Maxim Integrated

MAX318CSA+ - SPST NO CMOS Analog Switch, 35 Ohm | Maxim

Teilenummer: MAX318CSA+ ✓ Aktiv
35 Ohm Rds(on) 8-SOIC (NSOIC) Package
MOQ: 1 |

MAX318CSA+ Übersicht

The Maxim Integrated MAX318CSA+ is a precision, single-pole single-throw (SPST) normally-open CMOS analog switch with a maximum on-resistance of 35 Ohm, packaged in an 8-pin SOIC (NSOIC) surface-mount package. It is a 1:1 multiplexer: one independent switch, one signal path, complementary-family sibling to the MAX317 (normally closed) and MAX319 (SPDT) parts in the same series.

An analog switch is a solid-state, MOSFET-based signal router that connects or disconnects an analog signal path under digital control, sitting in the interface IC layer between sensors, converters and a system microcontroller. Unlike a mechanical relay, it switches in nanoseconds with negligible off-state leakage, making it the standard building block for sample-and-hold front ends, programmable gain stages, test-point muxes and isolated-signal routing.

Key characteristics of the MAX318CSA+ include a maximum on-resistance of 35 Ohm, on-resistance matching held within 2 Ohm between channels and variation of only 3 Ohm maximum across the analog signal range, and very low leakage of less than 250 pA at +25 degC rising to less than 6 nA at +85 degC. The part is listed in production by Analog Devices and is specified over a 0 degC to +70 degC commercial temperature range in the SOIC package.

Internally the device uses CMOS transmission gates, so the signal path is symmetrical and the switch behaviour does not depend on the control polarity in the same way a bipolar multiplexer does. The small, flat on-resistance curve preserves signal integrity for low-frequency analog signals, while the low leakage keeps the off-state contribution to system error negligible when a single measurement or sensor node is selected.

Typical uses include routing sensor outputs into a single ADC input, multiplexing discrete resistive networks into a programmable gain amplifier, isolating a precision reference from a measurement node, selecting between test points during board bring-up, and building small sample-and-hold front ends in instrumentation equipment. Any of these functions can also be handled with a relay, but the CMOS switch removes the slow mechanical switching time and the contact bounce that plague relay-based solutions at higher cycle rates.

When laying out the MAX318CSA+, place the device close to the source and destination of the analog path so that the switched trace stays short and the 35 Ohm series resistance has the least effect on signal settling. Keep the supply decoupling capacitor adjacent to the V+ and ground pins, and route control traces away from the analog node where board area allows, because charge injection through the control line can create a transient step at the moment of switching.

This page consolidates the distributor availability picture, the family-level drop-in alternatives in the same 8-SOIC footprint, and the practical routing and layout notes that engineers usually have to piece together from the manufacturer data sheet and application experience.

Drop-in-Alternativen für MAX318CSA+ – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.

MAX318ESA+

✅ Drop-In
📦 8-SOIC (NSOIC)
Extended temperature grade -40 degC to +85 degC vs 0 degC to +70 degC commercial; same SPST NO configuration, same 35 Ohm max on-resistance, same pinout

📋 Referenzalternative (nicht im Katalog)

MAX318CSA+T

✅ Drop-In
📦 8-SOIC (NSOIC)
Identical die and electrical characteristics, reel tape-and-reel packaging code; 0 degC to +70 degC commercial grade

📋 Referenzalternative (nicht im Katalog)

MAX318ESA+T

✅ Drop-In ⚠️ Spezifikationen ungeprüft
📦 8-SOIC (NSOIC)
Extended -40 degC to +85 degC temperature grade plus reel packaging; same 35 Ohm max on-resistance and identical SPST NO pinout

📋 Referenzalternative (nicht im Katalog)

MAX318CSA-T

✅ Drop-In
📦 8-SOIC (NSOIC)
Legacy tape-and-reel ordering code of the same die; electrical specifications identical, 35 Ohm max on-resistance and 0 degC to +70 degC commercial grade

📋 Referenzalternative (nicht im Katalog)

MAX318CSA+ Grenzwerte & elektrische Eigenschaften

Switch Configuration SPST (single-pole single-throw), 1:1 multiplexer
Switch State Normally open (NO)
Number of Circuits 1
On-Resistance (max) 35 Ohm
On-Resistance Matching Between Channels Within 2 Ohm
On-Resistance Variation Over Signal Range 3 Ohm max
Off-State Leakage at +25 degC Less than 250 pA
Off-State Leakage at +85 degC Less than 6 nA
Anzahl der Pins 8
Gehäuse 8-SOIC (NSOIC)
Montageart Surface mount
Betriebstemperaturbereich 0 degC to +70 degC
Process Technology Precision CMOS
Lebenszyklusstatus Production (per manufacturer product page)
RoHS-Status Compliant
Manufacturer Listed Lead Time 10 weeks (per distributor listing)

MAX318CSA+ 8-soic (nsoic) Pinbelegungsleitfaden

Pinbelegung für MAX318CSA+ (8-soic (nsoic)-Gehäuse). Pin-Nummerierung, Funktionen und Anschlussdiagramme sind im Herstellerdatenblatt definiert. Entnehmen Sie diesem den genauen Footprint und Lötrichtlinien.

Pinbelegungsdiagramm für MAX318CSA+ im 8-soic (nsoic)-Gehäuse

Keine detaillierten Pinbelegungsdaten verfügbar für MAX318CSA+.

Siehe die Datenblatt für die vollständige Pin-Konfiguration.

Typische Anwendungen

MAX318CSA+ ist geeignet für 6 Anwendungs: Precision ADC Front-End Sensor Multiplexer, Programmable Gain and Feedback Network Switching, Sample-and-Hold and Instrumentation Multiplexing, Battery-Powered Portable Sensor Terminals, Test Point Selection and Board Bring-Up, Audio and Low-Level Signal Routing.

📊

Precision ADC Front-End Sensor Multiplexer

The MAX318CSA+ suits designs that must bring several low-level sensor outputs into one conversion channel. Because the switch adds at most 35 Ohm in series and leaks less than 250 pA at +25 degC when open, the error it injects into a high-impedance sensor node is well below the noise floor of most resistive or capacitive sensors. Use it to place one thermocouple, bridge output or strain-gauge channel at a time onto the input of a precision SAR ADC such as the ADS1262IPW, with the on/off control driven by the host MCU. The flat on-resistance curve, varying no more than 3 Ohm across the signal range, keeps the switched-node gain error independent of input level. Add a small hold capacitor at the ADC input when the source impedance is high, so that the switch capacitance can settle within the acquisition window.

⚙️

Programmable Gain and Feedback Network Switching

In programmable-gain and feedback topologies, the MAX318CSA+ can select between discrete resistive networks without changing the amplifier gain stability analysis in a fundamental way. Switching a 35 Ohm series element in front of a high-impedance amplifier input adds only a small, predictable series term, while the leakage of less than 250 pA at +25 degC keeps the input bias error negligible relative to the resistor network itself. This makes the part suitable for gain-ranging stages built around precision amplifiers such as the AD8015ARZ, where the gain set must change under software control. Because the resistance is flat across the analog signal range, gain accuracy does not drift as the input signal rises. Keep the switched network ground-referenced close to the switch ground pin to prevent switching transients from modulating the amplifier input.

🧰

Sample-and-Hold and Instrumentation Multiplexing

The MAX318CSA+ is well suited to building compact sample-and-hold front ends in bench and field instrumentation, where a mechanical relay would be too slow. The CMOS transmission gate switches in nanoseconds and its off-state leakage of less than 250 pA at +25 degC keeps the held capacitor from discharging quickly, which is what makes a switched-capacitor hold stage practical. Route the switched node into a precision buffer such as the AD7492ARZ, a low-noise ADC driver, so that the hold capacitor sees a high input impedance rather than the switch itself. The 35 Ohm series resistance adds only a small settling term to the RC time constant, so a moderate hold capacitance is usually sufficient. Confirm the supply voltage limits and control-logic levels in the manufacturer data sheet before finalising the hold timing.

🔋

Battery-Powered Portable Sensor Terminals

In battery-powered field terminals and IoT sensor nodes, the MAX318CSA+ lets one analog input pin serve several sensing channels, which reduces both board area and the number of pins on a constrained microcontroller. The off-state leakage of less than 250 pA at +25 degC is negligible against the microamp-level standby currents typical of portable equipment, and the CMOS switch adds no significant quiescent current beyond its own control logic. A single SPST normally-open device is ideal for routing a reference or a thermistor line to a shared ADC when the system does not need fail-safe or SPDT behaviour. Because the switch sits between a long sensor trace and the converter input, place it near the converter to keep the switched section short and shielded from the field wiring that may pick up noise.

🔬

Test Point Selection and Board Bring-Up

The MAX318CSA+ provides a simple way to route several test points to a single measurement channel during board bring-up, functional test and production calibration. A CMOS analog switch isolates the nodes it is not selecting, so the leakage of less than 250 pA at +25 degC does not drag the measurement of an adjacent high-impedance node. Switching speeds in the nanosecond range let a tester scan nodes rapidly without the settling penalty of an electromechanical relay. Use the part to isolate a precision reference from a measurement node when the reference must remain undisturbed during a calibration sweep, and to select between an internal and external clock or reference in a mixed-signal board. Keep the control traces short and route them away from the sensitive analog pads during layout.

🎧

Audio and Low-Level Signal Routing

For low-level audio and baseband signal routing, the MAX318CSA+ can be used as a mute or source-select element in small-signal paths. Its low off-state leakage of less than 250 pA at +25 degC means that an open switch contributes negligibly to the input impedance of the following stage, and the on-resistance of 35 Ohm is acceptable when the source impedance is of the order of hundreds of ohms. Precision amplifiers such as the AD8016ARP or AD8018ARZ can sit behind the switch for headphone and line-level buffering, with the switch selecting between two sources or muting the chain. The flat on-resistance characteristic, varying 3 Ohm maximum over the signal range, means the gain error introduced is essentially independent of level, which keeps channel-to-channel matching predictable in stereo or multi-zone audio paths.

What is the MAX318CSA+ and what does it do?
The MAX318CSA+ is a precision, single-pole single-throw (SPST) normally-open CMOS analog switch from Maxim Integrated, with a maximum on-resistance of 35 Ohm in an 8-pin SOIC package. According to the MAX318 manufacturer data sheet, it is one of a family of precision CMOS monolithic analog switches: MAX317 is normally closed, MAX318 is normally open, and MAX319 is single-pole double-throw. The part connects or disconnects an analog signal path under digital control and is listed in production.
What is the on-resistance of the MAX318CSA+?
The MAX318CSA+ has a maximum on-resistance of 35 Ohm, and its on-resistance matches within 2 Ohm between channels while varying by no more than 3 Ohm across the analog signal range. That flat characteristic is what keeps the gain and settling behaviour of the switched node predictable across the input range. For comparison, a mechanical relay or a discrete MOSFET switch typically shows much larger resistance variation with signal amplitude.
What is the leakage current of the MAX318CSA+?
Off-state leakage is less than 250 pA at +25 degC and less than 6 nA at +85 degC. This low leakage keeps the switch nearly transparent when it is open, which matters in high-impedance sensor nodes and precision measurement chains where the leakage of the switch itself would otherwise appear as an offset error. Use the pin-description and leakage tables in the manufacturer data sheet when sizing the input impedance of the node behind the switch.
Is the MAX318CSA+ a drop-in replacement for the MAX318CSA?
The MAX318CSA+ is the lead-free, taped-and-reelled ordering code of the MAX318CSA, and both use the same 8-SOIC footprint with identical electrical characteristics. The suffix difference is a packaging and ordering convention rather than an electrical change. When you substitute one for the other in an existing design, the land pattern is unchanged, so no PCB rework is required.
What is the difference between MAX318CSA+ and MAX318ESA+?
The MAX318CSA+ is the commercial-temperature 0 degC to +70 degC grade, while the MAX318ESA+ is the extended-temperature grade running from -40 degC to +85 degC. Both are 8-SOIC precision SPST normally-open CMOS analog switches with the same 35 Ohm maximum on-resistance and the same pin arrangement, so the ESA variant can be fitted as a drop-in upgrade when the enclosure temperature exceeds the commercial range.
Can the MAX319CSA+T replace the MAX318CSA+?
No. The MAX319 is a single-pole double-throw switch, while the MAX318 is single-pole single-throw, so the two are not pin-for-pin interchangeable even though both are 8-SOIC parts. According to the MAX318 family documentation, the MAX319 provides one normally-open and one normally-closed throw, adding a second switch path that the MAX318 footprint does not wire in the same way. Use the MAX319 only when your circuit actually needs the SPDT function.
Is the MAX317CSA+ a substitute for the MAX318CSA+?
The MAX317 is the normally-closed member of the same family, so it is not a functional drop-in replacement for the normally-open MAX318. In a design that depends on the switch closing when the control input is deasserted, swapping to the MAX317 inverts the control logic and changes the fail-state behaviour of the circuit. Confirm the switch state required by your system before selecting the family member.
What is the operating temperature range of the MAX318CSA+?
The MAX318CSA+ in the SOIC package is specified from 0 degC to +70 degC, the commercial grade of the MAX318 series. Industrial or automotive designs that must work below 0 degC or above 70 degC should use the extended-temperature MAX318ESA+ variant, which shares the same 8-SOIC footprint and pinout. Verify the temperature grade in the ordering information for the exact package code you are placing.
Where can I download the MAX318CSA+ datasheet PDF?
The MAX318CSA+ datasheet PDF is available from the manufacturer product page for the MAX318 family, which links the precision SPST CMOS analog switch data sheet along with the product selection table. The data sheet includes the pin description, on-resistance and leakage characterisation, and the ordering table that lists the CSA and ESA suffixes. Use the analog.com MAX318 product page as the canonical starting point for the document.
Where do I find the MAX318CSA+ pinout?
The MAX318CSA+ pinout is documented in the pin-description table of the manufacturer MAX318 data sheet, which covers the 8-pin SOIC and NSOIC packages. Because the same family also includes SPDT and normally-closed variants, use the table for the specific MAX318 part rather than a generic family diagram. The package drawing and land pattern should be taken from the same document section.
How do I use the MAX318CSA+ in a sensor multiplexer?
Place the MAX318CSA+ between several sensor outputs and one ADC input, driving the on/off control line with the host microcontroller so that only one sensor is connected at a time. Because the switch adds up to 35 Ohm in series and less than 250 pA of leakage at +25 degC, the error it contributes to a high-impedance sensor node is small compared with the sensor's own noise floor. Add a small hold capacitor at the ADC input if the source impedance is high enough that the switch capacitance cannot settle the sample in the available acquisition time.
What are the key specifications of MAX318CSA+ that engineers should know?
The MAX318CSA+ is a precision SPST normally-open CMOS analog switch: 35 Ohm maximum on-resistance, on-resistance matched within 2 Ohm and varying 3 Ohm maximum over the signal range, less than 250 pA leakage at +25 degC and less than 6 nA at +85 degC, one switch in an 8-SOIC package, and a 0 degC to +70 degC commercial temperature range. It is listed in production, so supply is stable for designs entering volume.
What can replace the MAX318CSA+ if it becomes unavailable?
The closest drop-in replacements are the other ordering codes of the same die in the same 8-SOIC footprint, such as the MAX318CSA-T tape-and-reel code and the extended-temperature MAX318ESA+ and MAX318ESA+T, plus the reel packaging variant MAX318CSA+T. All keep the same 8-pin land pattern and the same 35 Ohm-class on-resistance. If none of those are available, request a quotation on this page so an equivalent precision CMOS SPST switch in the SOIC-8 footprint can be sourced for you.
What is the best Analog Devices equivalent for the MAX318CSA+?
Within the same manufacturer, the MAX318ESA+ is the closest equivalent because it shares the 8-SOIC footprint, the SPST normally-open configuration and the 35 Ohm-class on-resistance, adding only the extended -40 degC to +85 degC temperature range. A cross-manufacturer SOIC-8 precision SPST switch with comparable leakage would need to be qualified against the leakage and on-resistance matching figures in the MAX318 data sheet before it can be treated as a drop-in.
Is the MAX318CSA+ suitable for battery-powered instrumentation?
The MAX318CSA+ is suitable for low-power instrumentation provided the supply rail stays inside the range allowed by the manufacturer data sheet, which should be confirmed against the specific part. Its low off-state leakage of less than 250 pA at +25 degC means the switch adds very little drain to a battery-powered front end, and the CMOS construction avoids the quiescent draw that a bipolar multiplexer would impose. Keep the supply decoupling capacitor close to the device to keep switching transients out of the analog node.
How long is the lead time for the MAX318CSA+?
A distributor listing for the MAX318CSA family shows a manufacturer lead time of 10 weeks with the part supplied on 2,500-piece reels. Because the MAX318 is listed in production, long-term availability is expected, but you should confirm the current lead time, minimum order quantity and reel packaging for your design. Use the Request a Quote form on this page to get the current lead time and stock position for this exact ordering code.
How do I lay out the MAX318CSA+ on the PCB?
Route the switched analog trace as a short, direct path between the switch pins and the node they serve, and place the bypass capacitor immediately adjacent to the supply and ground pins. Keep the digital control trace away from the analog input pad and connect the ground reference close to the switch ground pin so switching charge injection has a short return path. If the node behind the switch is high impedance, add a small hold capacitor at the destination to give the switch capacitance time to settle.

Technische Referenzdaten für MAX318CSA+ – Vergleich, Designhinweise und Compliance-Informationen.

Auswahlhilfe

Choose the MAX318CSA+ when you need a single normally-open precision CMOS switch with a maximum on-resistance of 35 Ohm in an 8-SOIC package and your enclosure stays within 0 degC to +70 degC. Choose the MAX318ESA+ when the same pinout is needed but the ambient temperature extends to -40 degC to +85 degC; it is the drop-in upgrade with no layout change. Use MAX318CSA+T or MAX318CSA-T only to match your assembly and packaging format, since the electrical performance is identical to the tube-packed MAX318CSA+. If your design needs a normally-closed path, select the MAX317; if it needs two throws, select the MAX319 - neither is a drop-in for the MAX318 because the switching behaviour and pin configuration differ. For an application where the 35 Ohm series resistance is too high for the source impedance, or where a faster, lower-resistance switch is needed, specify a different part family rather than assuming an equivalence.

Vergleich mit Alternativen

Parameter Dieses Produkt MAX318ESA+ MAX318CSA+T MAX318ESA+T MAX318CSA-T
Package 8-SOIC (NSOIC) 8-SOIC (NSOIC) - same 8-SOIC (NSOIC) - same 8-SOIC (NSOIC) - same 8-SOIC (NSOIC) - same
Brand Maxim Integrated Maxim Integrated Maxim Integrated Maxim Integrated Maxim Integrated
Switch Configuration SPST, 1 circuit, normally open SPST, 1 circuit, normally open SPST, 1 circuit, normally open SPST, 1 circuit, normally open SPST, 1 circuit, normally open
On-Resistance (max) 35 Ohm 35 Ohm 35 Ohm 35 Ohm 35 Ohm
Off-State Leakage at +25 degC Less than 250 pA Less than 250 pA Less than 250 pA Less than 250 pA Less than 250 pA
Off-State Leakage at +85 degC Less than 6 nA Less than 6 nA Less than 6 nA Less than 6 nA Less than 6 nA
Operating Temperature Range 0 degC to +70 degC -40 degC to +85 degC (extended) 0 degC to +70 degC -40 degC to +85 degC (extended) 0 degC to +70 degC
On-Resistance Matching Between Channels Within 2 Ohm Within 2 Ohm Within 2 Ohm Within 2 Ohm Within 2 Ohm
On-Resistance Variation Over Signal Range 3 Ohm max 3 Ohm max 3 Ohm max 3 Ohm max 3 Ohm max
Packaging Form 8-SOIC, commercial grade ordering code 8-SOIC, extended grade, tube 8-SOIC, tape and reel 8-SOIC, extended grade, tape and reel 8-SOIC, legacy tape and reel

Wichtigste Unterscheidungsmerkmale

  • Extended-temperature sibling available in the identical footprint (vs. MAX318ESA+)
  • Low off-state leakage keeps the switched node effectively unloaded (vs. Mechanical relay alternative)
  • Flat on-resistance keeps gain error independent of signal level (vs. Discrete MOSFET switch implementation)
  • Ordering and packaging flexibility from the same die (vs. MAX318CSA-T)

Designhinweise

Keep the switched analog path short: place the MAX318CSA+ so the trace from the switch to the destination node is as short as possible, because the 35 Ohm maximum on-resistance acts in series with the source impedance and adds to settling time. Route the control line away from the analog pad, and connect the ground reference of the switch close to the device ground pin so that charge injection from the control transition returns locally instead of through the sensitive analog return path.

Do not treat the MAX318 family members as interchangeable. MAX318 is normally open, MAX317 is normally closed, and MAX319 is single-pole double-throw; only the same switching behaviour can be dropped into an existing board without changing the control logic. Confirm the required switch state, the supply voltage limits and the control logic levels in the manufacturer data sheet before fitting any ordering code of the family.

At the input of a high-impedance node the off-state leakage of less than 250 pA at +25 degC is usually negligible, but the on-state 35 Ohm plus the switch capacitance can slow the acquisition of a high-impedance source. If the ADC settling window is tight, add a small hold capacitor at the destination node and re-check the acquisition time with the switch capacitance included. The on-resistance flatness of 3 Ohm maximum across the signal range keeps the gain error level-independent.

Place the supply bypass capacitor immediately adjacent to the supply and ground pins of the device, and keep the supply decoupling loop as small as possible. Switching transients produced at the moment of turn-on are supplied locally in this way, preventing them from modulating the reference or the analog bus elsewhere on the board. Use a ceramic capacitor chosen per the decoupling guidance in the manufacturer data sheet for the operating frequency range of your system.

Compliance-Informationen

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
Bleifrei
Yes
Halogenfrei
Unknown
Konfliktmineralien
Unknown

RoHS compliance is indicated on the distributor series listing for the MAX318 family; the + suffix on the ordering code denotes the lead-free termination. No AEC-Q100 qualification is claimed for this part, and no REACH, halogen-free or conflict-minerals declaration was available for the MAX318CSA+.

Daten verifiziert am: 2026-11-18 – Daten geprüft und kuratiert vom Bauteil-Engineering-Team von XAIPART

Ähnliche Suchanfragen

MAX318CSA+ MAX318CSA+ datasheet MAX318CSA+ datasheet pdf MAX318CSA+ pinout MAX318CSA+ equivalent MAX318CSA+ replacement MAX318CSA+ drop-in replacement MAX318CSA+ vs MAX318ESA+ MAX318CSA+ price MAX318CSA+ stock MAX318 analog switch 35 ohm on-resistance MAX318CSA+ 8-SOIC footprint Maxim Integrated MAX318CSA+ SPST normally open CMOS switch SOIC-8 MAX318CSA+ sensor multiplexer application

Verwandte Bauteile & Begriffe

Maxim Integrated Analog Devices MAX318CSA+ MAX318CSA MAX318CSA+T MAX318CSA-T MAX318ESA+ MAX318ESA+T MAX317 MAX319 analog switch SPST normally open switch CMOS transmission gate multiplexer interface IC semiconductor on-resistance off-state leakage 8-SOIC NSOIC surface mount precision analog switch sample and hold RoHS lead-free termination
Schnellangebot-RFQ
Geben Sie alle Details an – unser Vertriebsteam antwortet innerhalb von 24 Stunden
Teilenummer Hersteller Gehäuse QTY Zielpreis Gesamt
✓
Angebotsanfrage gesendet!

Wir antworten innerhalb von 24 Stunden auf Ihre E-Mail

1
RFQ gesendet
2
Angebot erhalten
3
Bestellung aufgegeben
4
Zahlung
5
Versandt
6
Geliefert
RFQ-Details ansehen