MAX3221IDBRG4 - 250kbps Single RS-232 Transceiver | Texas Instruments
MPN: MAX3221IDBRG4 ✓ সক্রিয়MAX3221IDBRG4 সারাংশ
An RS-232 transceiver is an interface IC that converts logic-level transmit and receive signals into RS-232 line levels and back again. It belongs to the transceiver hierarchy within interface ICs and combines a line driver, line receiver, and charge-pump voltage generation in one package. The MAX3221 is intended for point-to-point serial links, industrial equipment, data acquisition systems, and legacy peripheral connections that do not require multiple RS-232 channels.
The MAX3221IDBRG4 accepts a 3 V to 5.5 V supply and can operate with a 3.3 V supply even when its digital input signals reach 5 V. Four external 0.1 µF charge-pump capacitors are specified. Typical standby current is only 1 µA, helping conserve power when the interface is inactive. The device also meets or exceeds the requirements of TIA/EIA-232-F and ITU V.28, providing standards-based operation for conventional RS-232 links.
Internally, the dual charge-pump circuit develops the positive and negative voltages required by the RS-232 driver. The receiver converts the corresponding differential voltage at its input back into a logic-level signal. This architecture allows the MAX3221 to communicate with systems whose logic supply is lower than the traditional 5 V RS-232 interface level while avoiding a separate negative supply rail in the equipment.
Typical applications include industrial serial controllers, test equipment, configuration interfaces, printers, scanners, and embedded systems that expose an RS-232 port. The 250 kbit/s maximum data rate is suitable for moderate-speed control and data-transfer links. Designers should still account for cable length, baud-rate tolerance, grounding, and transceiver enable timing when establishing a reliable connection.
The principal design consideration is the charge-pump capacitor network. Place the four 0.1 µF capacitors close to their associated IC pins, follow the polarity shown in the manufacturer datasheet, and keep the high-voltage RS-232 outputs away from sensitive logic traces. The bus pins receive ±15 kV HBM ESD protection, but cable-side transients and secondary protection requirements should be evaluated for the completed system.
This product page consolidates the exact electrical ratings, package information, drop-in cross-reference options, interface applications, and PCB-design considerations needed to evaluate and implement the MAX3221IDBRG4. It also distinguishes confirmed same-package replacements from options that require a different footprint, helping prevent redesign errors during sourcing and second-source decisions.
এর জন্য ড্রপ-ইন বিকল্প MAX3221IDBRG4 — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।
এই সিরিজের ভ্যারিয়েন্ট
একই সিরিজের মডেল যেগুলো drop-in compatible MAX3221IDBRG4 (একই form factor এবং footprint) — পার্থক্য রয়েছে ESD Protection, Maximum Data Rate, RS-232 Compliance.
MAX3221IDBR
✅ ড্রপ-ইনমূল্যের জন্য যোগাযোগ করুন
ডেটাশিট দেখুন →SN65C3221EDBRG4
✅ ড্রপ-ইন📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
MAX3221IDBRG4 বিশেষণ
| Product Type | Single-channel RS-232 line driver and receiver |
| Supply Voltage Range | 3 V to 5.5 V |
| Maximum Data Rate | 250 kbit/s |
| Number of Drivers | 1 |
| Number of Receivers | 1 |
| ESD Protection | ±15 kV HBM on RS-232 bus pins |
| Low Standby Current | 1 µA typical |
| External Charge-Pump Capacitors | 4 × 0.1 µF |
| 5 V Logic Input Compatibility | Accepted with 3.3 V supply |
| RS-232 Compliance | Meets or exceeds TIA/EIA-232-F |
| ITU Compliance | Meets or exceeds ITU V.28 |
| প্যাকেজ | 16-pin SSOP |
| মাউন্টিং টাইপ | Surface mount |
MAX3221IDBRG4 16-pin ssop পিন কনফিগারেশন গাইড
MAX3221IDBRG4 (16-pin ssop প্যাকেজ)-এর পিন কনফিগারেশন। পিন নম্বরিং, ফাংশন এবং সংযোগ ডায়াগ্রাম প্রস্তুতকারকের ডেটাশিটে সংজ্ঞায়িত করা আছে। সঠিক ফুটপ্রিন্ট এবং সোল্ডারিং নির্দেশিকার জন্য এটি দেখুন।
এর জন্য বিস্তারিত পিনআউট ডেটা পাওয়া যায়নি MAX3221IDBRG4.
দেখুন ডেটাশিট সম্পূর্ণ পিন কনফিগারেশনের জন্য।
সাধারণ ব্যবহার
MAX3221IDBRG4 এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Industrial Controller Serial Port, Embedded UART to RS-232 Bridge, Data Acquisition Equipment, Test and Measurement Interface, Legacy Peripheral Configuration Port, Portable Diagnostic Equipment.
Industrial Controller Serial Port
The MAX3221IDBRG4 fits industrial controllers that need a wired RS-232 command or configuration port while operating from a 3 V or 3.3 V logic supply. Its one-driver and one-receiver implementation supports full-duplex point-to-point communication at rates up to 250 kbit/s, while the internal dual charge-pump removes the need for a separate negative supply rail. The ±15 kV HBM bus-pin protection is useful when the connector is exposed to routine human-contact ESD events. Designers should still evaluate the finished enclosure, cable routing, grounding, and industrial surge environment.
সুপারিশকৃত
Embedded UART to RS-232 Bridge
The MAX3221IDBRG4 provides a straightforward interface between a microcontroller UART and an RS-232 peer. Its 3 V to 5.5 V operating range supports both 3.3 V and 5 V systems, while the ability to accept 5 V logic input with a 3.3 V supply simplifies mixed-voltage designs. One driver and one receiver are sufficient for a full-duplex link operating up to 250 kbit/s. Firmware must configure the UART baud rate and data framing to match the connected equipment, and the cable must use the correct signal and ground assignments.
সুপারিশকৃত
Data Acquisition Equipment
The MAX3221IDBRG4 is appropriate for laboratory and industrial data-acquisition units that communicate with a legacy RS-232 controller. The 250 kbit/s maximum rate supports moderate-speed command and measurement traffic without using a multi-channel transceiver. Its low 1 µA typical standby current is advantageous in portable or intermittently powered instruments, while the 3 V to 5.5 V supply range supports compact mixed-voltage hardware. For reliable measurements, route the interface ground carefully, keep cable transients away from sensitive signal paths, and verify grounding at the system boundary.
সুপারিশকৃত
Test and Measurement Interface
The MAX3221IDBRG4 can add a service or control port to test and measurement equipment without requiring a legacy negative-voltage supply. Its dual charge-pump architecture develops the required RS-232 levels internally, and the external 0.1 µF capacitor network should be placed according to the manufacturer layout guidance. A single channel is appropriate for remote commands, calibration files, or status reporting at rates up to 250 kbit/s. Technicians connecting unfamiliar cables should also use appropriate external transient protection when the test environment includes severe surges.
সুপারিশকৃত
Legacy Peripheral Configuration Port
The MAX3221IDBRG4 is useful for connecting a modern controller to printers, scanners, scales, or other legacy peripherals that expose an RS-232 port. Its one-driver and one-receiver arrangement matches a standard full-duplex RS-232 link, and its 250 kbit/s capability is generally suitable for configuration and short data transfers. The interface can run from 3.3 V while accepting compatible 5 V logic inputs, reducing the need for level-shifters in mixed embedded systems. Confirm connector pinout, DTE or DCE roles, and cable directionality before production use.
সুপারিশকৃত
Portable Diagnostic Equipment
The MAX3221IDBRG4 supports portable diagnostic tools that need a wired RS-232 connection but cannot depend on a 5 V-only interface circuit. Its 3 V to 5.5 V operating range and 1 µA typical standby current suit battery-managed equipment, while ±15 kV HBM protection reduces sensitivity to common connector ESD events. The 250 kbit/s limit is adequate for diagnostic commands and moderate diagnostic packets. A complete portable design should account for battery-voltage variation, connector grounding, cable retention, and any protection required beyond the IC's specified human-body-model ESD rating.
সুপারিশকৃত
সুপারিশকৃত পণ্যের সারসংক্ষেপ
এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা MAX3221IDBRG4 — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।
নির্বাচন গাইড
বিকল্পের সাথে তুলনা
| পারামিটার | এই পণ্য | MAX3221IDBR | SN65C3221EDBRG4 |
|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 16-pin SSOP | 16-pin SSOP - same package | 16-pin SSOP - same package |
| Device Type | Single-channel RS-232 transceiver | Single-channel RS-232 transceiver | Single-channel RS-232 transceiver |
| Drivers | 1 | 1 | 1 |
| Receivers | 1 | 1 | 1 |
মূল পার্থক্যসমূহ
- Single-channel RS-232 operation with integrated charge pump (বনামSN65C3221EDBRG4)
- Wide low-voltage supply compatibility (বনামMAX3221IDBR)
- Documented bus-pin ESD protection (বনামSN65C3221EDBRG4)
ডিজাইন নোট
Place the four 0.1 µF charge-pump capacitors immediately beside the MAX3221IDBRG4 capacitor pins, following the exact polarity and topology in the Texas Instruments datasheet. Keep each trace short and avoid routing sensitive signals beneath the charge-pump network. The pins should also be decoupled according to the manufacturer layout guidance. Correct placement reduces capacitor-loop area, supports stable charge-pump operation, and limits coupling of generated noise into adjacent circuitry.
Do not infer RS-232 pin compatibility from package size alone. Confirm the receiver-enable behavior, signal names, logic thresholds, supply range, and charge-pump connections for any proposed replacement. The MAX3221IDBR and SN65C3221EDBRG4 are confirmed same-package candidates, but a production substitution still requires comparison of the complete electrical specifications and application diagrams. Also verify whether the connected equipment expects DTE or DCE pinout and cable directionality.
Keep the RS-232 driver outputs and charge-pump nodes away from sensitive analog traces, clocks, and communication lines. Use a solid ground plane, provide a low-impedance chassis or signal-ground path at the connector, and route the cable-side interface according to the completed system's EMC strategy. The integrated ±15 kV HBM protection handles specified human-body-model ESD, but it does not replace surge protection for severe industrial cable environments.
কমপ্লায়েন্স তথ্য
The MAX3221 documentation identifies ±15 kV HBM ESD protection and compliance with TIA/EIA-232-F and ITU V.28. RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations were not established from the cited manufacturer and distributor records.