Texas Instruments

MAX3221IDBRG4 - 250kbps Single RS-232 Transceiver | Texas Instruments

MPN: MAX3221IDBRG4 ✓ Aktif
3 V to 5.5 V Vdss 1 µA typical Id 16-pin SSOP Package
MOQ: 1 |

MAX3221IDBRG4 Ringkasan

The Texas Instruments MAX3221IDBRG4 is a single-channel RS-232 line driver and receiver operating from a 3 V to 5.5 V supply at rates up to 250 kbit/s. The device is packaged in a 16-pin SSOP and provides one driver and one receiver with ±15 kV electrostatic-discharge protection on the bus pins. Its dual charge-pump design supports low-voltage digital systems that must communicate through an RS-232 interface.

An RS-232 transceiver is an interface IC that converts logic-level transmit and receive signals into RS-232 line levels and back again. It belongs to the transceiver hierarchy within interface ICs and combines a line driver, line receiver, and charge-pump voltage generation in one package. The MAX3221 is intended for point-to-point serial links, industrial equipment, data acquisition systems, and legacy peripheral connections that do not require multiple RS-232 channels.

The MAX3221IDBRG4 accepts a 3 V to 5.5 V supply and can operate with a 3.3 V supply even when its digital input signals reach 5 V. Four external 0.1 µF charge-pump capacitors are specified. Typical standby current is only 1 µA, helping conserve power when the interface is inactive. The device also meets or exceeds the requirements of TIA/EIA-232-F and ITU V.28, providing standards-based operation for conventional RS-232 links.

Internally, the dual charge-pump circuit develops the positive and negative voltages required by the RS-232 driver. The receiver converts the corresponding differential voltage at its input back into a logic-level signal. This architecture allows the MAX3221 to communicate with systems whose logic supply is lower than the traditional 5 V RS-232 interface level while avoiding a separate negative supply rail in the equipment.

Typical applications include industrial serial controllers, test equipment, configuration interfaces, printers, scanners, and embedded systems that expose an RS-232 port. The 250 kbit/s maximum data rate is suitable for moderate-speed control and data-transfer links. Designers should still account for cable length, baud-rate tolerance, grounding, and transceiver enable timing when establishing a reliable connection.

The principal design consideration is the charge-pump capacitor network. Place the four 0.1 µF capacitors close to their associated IC pins, follow the polarity shown in the manufacturer datasheet, and keep the high-voltage RS-232 outputs away from sensitive logic traces. The bus pins receive ±15 kV HBM ESD protection, but cable-side transients and secondary protection requirements should be evaluated for the completed system.

This product page consolidates the exact electrical ratings, package information, drop-in cross-reference options, interface applications, and PCB-design considerations needed to evaluate and implement the MAX3221IDBRG4. It also distinguishes confirmed same-package replacements from options that require a different footprint, helping prevent redesign errors during sourcing and second-source decisions.

Alternatif penggantian untuk MAX3221IDBRG4 — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.

Variasi di dalam seri ini

Model-series yang sama yang kompatibel dengan penggantian MAX3221IDBRG4 (sama faktor bentuk dan footprint) — berbeda di dalam ESD Protection, Maximum Data Rate, RS-232 Compliance.

Texas Instruments
ESD Protection: ±15 kV HBM on serial-port connection pins, including GND
Maximum Data Rate: 250 kbps
RS-232 Compliance: TIA/EIA-232-F and ITU V.28
Bandingkan dengan MAX3221IDBRG4 →

MAX3221IDBR

✅ Drop-In
Texas Instruments
📦 16-pin SSOP
Single-channel RS-232 line driver and receiver · 3 V to 5.5 V · 250 kbps · 1 · 1 · ±15 kV HBM on serial-port connection pins, including GND · 1 µA · 4 × 0.1 µF

Kontak untuk harga

Lihat Datasheet →

SN65C3221EDBRG4

✅ Drop-In
📦 16-pin SSOP
Matching 16-pin SSOP with equivalent 1-driver and 1-receiver RS-232 topology; enable, timing, and protection details require datasheet comparison.

📋 Alternatif referensi (tidak dalam katalog)

MAX3221IDBRG4 Spesifikasi

Product Type Single-channel RS-232 line driver and receiver
Supply Voltage Range 3 V to 5.5 V
Maximum Data Rate 250 kbit/s
Number of Drivers 1
Number of Receivers 1
ESD Protection ±15 kV HBM on RS-232 bus pins
Low Standby Current 1 µA typical
External Charge-Pump Capacitors 4 × 0.1 µF
5 V Logic Input Compatibility Accepted with 3.3 V supply
RS-232 Compliance Meets or exceeds TIA/EIA-232-F
ITU Compliance Meets or exceeds ITU V.28
Paket 16-pin SSOP
Tipe Mounting Surface mount

MAX3221IDBRG4 16-pin ssop Diamant Konfigurasi Panduan

Konfigurasi pin untuk MAX3221IDBRG4 (16-pin ssop pakai pakai). Penomoran pin, fungsi, dan diagram koneksi ditetapkan dalam datasheet produsen. Lihatnya untuk footprint dan pedoman perpindahan paruh.

Diamant diagram pakai pakai 16-pin ssop untuk MAX3221IDBRG4

Tidak ada data diatribut pin yang tersedia untuk MAX3221IDBRG4.

Lihat ke: datasheet produk untuk konfigurasi pin penuh.

Aplikasi Umum

MAX3221IDBRG4 cocok untuk 6 aplikasis: Industrial Controller Serial Port, Embedded UART to RS-232 Bridge, Data Acquisition Equipment, Test and Measurement Interface, Legacy Peripheral Configuration Port, Portable Diagnostic Equipment.

🏭

Industrial Controller Serial Port

The MAX3221IDBRG4 fits industrial controllers that need a wired RS-232 command or configuration port while operating from a 3 V or 3.3 V logic supply. Its one-driver and one-receiver implementation supports full-duplex point-to-point communication at rates up to 250 kbit/s, while the internal dual charge-pump removes the need for a separate negative supply rail. The ±15 kV HBM bus-pin protection is useful when the connector is exposed to routine human-contact ESD events. Designers should still evaluate the finished enclosure, cable routing, grounding, and industrial surge environment.

🔧

Embedded UART to RS-232 Bridge

The MAX3221IDBRG4 provides a straightforward interface between a microcontroller UART and an RS-232 peer. Its 3 V to 5.5 V operating range supports both 3.3 V and 5 V systems, while the ability to accept 5 V logic input with a 3.3 V supply simplifies mixed-voltage designs. One driver and one receiver are sufficient for a full-duplex link operating up to 250 kbit/s. Firmware must configure the UART baud rate and data framing to match the connected equipment, and the cable must use the correct signal and ground assignments.

📟

Data Acquisition Equipment

The MAX3221IDBRG4 is appropriate for laboratory and industrial data-acquisition units that communicate with a legacy RS-232 controller. The 250 kbit/s maximum rate supports moderate-speed command and measurement traffic without using a multi-channel transceiver. Its low 1 µA typical standby current is advantageous in portable or intermittently powered instruments, while the 3 V to 5.5 V supply range supports compact mixed-voltage hardware. For reliable measurements, route the interface ground carefully, keep cable transients away from sensitive signal paths, and verify grounding at the system boundary.

🖥️

Test and Measurement Interface

The MAX3221IDBRG4 can add a service or control port to test and measurement equipment without requiring a legacy negative-voltage supply. Its dual charge-pump architecture develops the required RS-232 levels internally, and the external 0.1 µF capacitor network should be placed according to the manufacturer layout guidance. A single channel is appropriate for remote commands, calibration files, or status reporting at rates up to 250 kbit/s. Technicians connecting unfamiliar cables should also use appropriate external transient protection when the test environment includes severe surges.

🖨️

Legacy Peripheral Configuration Port

The MAX3221IDBRG4 is useful for connecting a modern controller to printers, scanners, scales, or other legacy peripherals that expose an RS-232 port. Its one-driver and one-receiver arrangement matches a standard full-duplex RS-232 link, and its 250 kbit/s capability is generally suitable for configuration and short data transfers. The interface can run from 3.3 V while accepting compatible 5 V logic inputs, reducing the need for level-shifters in mixed embedded systems. Confirm connector pinout, DTE or DCE roles, and cable directionality before production use.

📱

Portable Diagnostic Equipment

The MAX3221IDBRG4 supports portable diagnostic tools that need a wired RS-232 connection but cannot depend on a 5 V-only interface circuit. Its 3 V to 5.5 V operating range and 1 µA typical standby current suit battery-managed equipment, while ±15 kV HBM protection reduces sensitivity to common connector ESD events. The 250 kbit/s limit is adequate for diagnostic commands and moderate diagnostic packets. A complete portable design should account for battery-voltage variation, connector grounding, cable retention, and any protection required beyond the IC's specified human-body-model ESD rating.

What is the MAX3221IDBRG4?
The MAX3221IDBRG4 is a Texas Instruments single-channel RS-232 transceiver containing one line driver, one receiver, and a dual charge-pump circuit. According to the Texas Instruments MAX3221 datasheet, it operates from a 3 V to 5.5 V supply, supports data rates up to 250 kbit/s, and provides ±15 kV HBM ESD protection on the RS-232 bus pins. It is packaged in a 16-pin SSOP for compact embedded and industrial equipment.
What is the operating voltage of MAX3221IDBRG4?
The MAX3221IDBRG4 operates from 3 V to 5.5 V. According to the Texas Instruments MAX3221 datasheet, the device also accepts 5 V logic input signals when its supply is 3.3 V. This combination allows it to bridge a 3.3 V controller with a conventional RS-232 connector while keeping the interface supply below the traditional 5 V level. Check the selected logic thresholds in the datasheet before connecting external signals.
What is the maximum data rate of MAX3221IDBRG4?
The MAX3221IDBRG4 supports RS-232 data rates up to 250 kbit/s. This rate is appropriate for configuration ports, industrial controllers, test equipment, and legacy peripheral connections rather than high-volume storage transfers. Actual throughput also depends on the UART, protocol efficiency, cable characteristics, grounding, and receiver threshold behavior. The Texas Instruments MAX3221 datasheet identifies 250 kbit/s as the maximum operating rate.
Where can I download the MAX3221IDBRG4 datasheet PDF?
The official MAX3221IDBRG4 technical documentation is available from the Texas Instruments MAX3221 product page at https://www.ti.com/product/MAX3221. The page provides the manufacturer datasheet, ordering information, pin data, and device parameters. Use the manufacturer PDF for the charge-pump capacitor connections, pin assignments, electrical characteristics, and recommended application circuit rather than relying on a secondary document for design sign-off.
Where can I find the MAX3221IDBRG4 pinout?
The MAX3221IDBRG4 pinout is shown in the Texas Instruments MAX3221 datasheet, available from the official product page. The device uses a 16-pin SSOP and requires four external 0.1 µF charge-pump capacitors. Assign PCB nets from the datasheet pin-description table and drawing, paying particular attention to driver outputs, receiver inputs, enable pins, supply, ground, and capacitor polarity. The pinout is left null here to avoid reproducing an unverified pin assignment.
Does MAX3221IDBRG4 need external charge-pump capacitors?
Yes, the MAX3221IDBRG4 requires four external 0.1 µF capacitors for its dual charge-pump circuit. According to the Texas Instruments MAX3221 datasheet, these capacitors are external rather than integrated. Place each capacitor directly beside the corresponding device pin and follow the polarity and connection diagram in the datasheet. Incorrect capacitor placement or polarity can impair voltage generation, upset communication, and increase EMI.
What does ±15 kV ESD protection mean for MAX3221IDBRG4?
The ±15 kV rating means the MAX3221IDBRG4 bus pins withstand ±15 kV human-body-model ESD events under the conditions defined by the Texas Instruments datasheet. The protection applies to the RS-232 connection pins, including ground as indicated in the device documentation. It does not guarantee immunity from every surge event or eliminate the need for system-level cable protection in severe industrial environments.
What can replace the MAX3221IDBRG4?
The SN65C3221EDBRG4 from Texas Instruments is a confirmed drop-in candidate with a matching 16-pin SSOP and equivalent one-driver, one-receiver RS-232 function. The MAX3221IDBR is also a same-package device-family option. Confirm supply voltage, data rate, enable logic, charge-pump capacitor values, ESD rating, and the exact footprint against the manufacturer datasheets before approving a substitution for production.
Is SN65C3221EDBRG4 the same as MAX3221IDBRG4?
The SN65C3221EDBRG4 is a pin-compatible SSOP-16 alternative to the MAX3221IDBRG4, with the same one-driver and one-receiver RS-232 topology. The cross-reference comparison identifies consistent terminals and packages. Before interchangeability is confirmed, compare both datasheets for operating voltage, maximum data rate, receiver enable behavior, charge-pump capacitor requirements, ESD rating, and propagation-delay limits.
When should I choose MAX3221IDBRG4 instead of SN65C3221EDBRG4?
Choose the MAX3221IDBRG4 when its documented supply range, 250 kbit/s rate, enable arrangement, and ±15 kV ESD specification match the finished product better than the SN65C3221EDBRG4. The SN65C3221EDBRG4 is appropriate when its electrical characteristics satisfy the design and its sourcing status offers an advantage. A valid drop-in decision must include a complete datasheet comparison, not footprint matching alone.
Is MAX3221IDBRG4 suitable for an industrial RS-232 interface?
The MAX3221IDBRG4 is suitable for many industrial RS-232 interfaces because it supports 3 V to 5.5 V operation, 250 kbit/s communication, 1 µA typical standby current, and ±15 kV HBM ESD protection. Industrial suitability still depends on the complete operating-temperature grade, electromagnetic environment, cable design, surge requirements, and system grounding. These conditions should be verified for each industrial product configuration.
How should the MAX3221IDBRG4 charge-pump capacitors be placed?
Place the four 0.1 µF charge-pump capacitors as close as practical to their associated MAX3221IDBRG4 pins, following the exact connection and polarity diagram in the Texas Instruments datasheet. Keep the routing short and symmetric where possible, and avoid routing charge-pump nodes beneath sensitive analog or high-speed signal traces. Adequate placement reduces loop area, supports predictable charge-pump operation, and limits generated EMI.
Can MAX3221IDBRG4 interface with a 3.3 V UART?
Yes, the MAX3221IDBRG4 can operate from a 3.3 V supply and accepts 5 V logic inputs according to the Texas Instruments MAX3221 datasheet. It therefore supports connection to a 3.3 V UART and other compatible logic circuits. Verify the UART voltage levels, receiver enable state, ground reference, and signal polarity in the system schematic, since interface standards alone do not guarantee compatibility with every peripheral.
Where can I buy MAX3221IDBRG4 online?
Use the Request a Quote form on this page to request MAX3221IDBRG4 availability, current pricing, and the required delivery quantity. The form is the appropriate route for a transactional inquiry because market pricing and stock can change rapidly. Include your target quantity, reel or tray preference, date code requirements, and shipping destination so the quote reflects the configuration you actually need.
What is the lead time for MAX3221IDBRG4?
Submit a lead-time request through the Request a Quote form on this page. The form captures the quantity and project schedule needed for an allocation response, avoiding reliance on a static stock statement that may change without notice. Include the required ship date and acceptable packaging configuration when requesting the quotation. Current lead time is therefore handled as a live commercial request rather than a fixed product specification.
What are the key specifications of MAX3221IDBRG4 that engineers should know?
The key MAX3221IDBRG4 specifications are a 3 V to 5.5 V supply, one RS-232 driver, one RS-232 receiver, and operation up to 250 kbit/s. According to the Texas Instruments MAX3221 datasheet, the 16-pin SSOP device also uses four external 0.1 µF capacitors, draws 1 µA in typical standby, accepts 5 V logic inputs with a 3.3 V supply, and provides ±15 kV HBM bus-pin ESD protection.

Data referensi engineering untuk MAX3221IDBRG4 — pembandingan, panduan desain, dan informasi konformitas.

Panduan Pemilihan

Choose the MAX3221IDBRG4 for a compact, single-channel RS-232 port that must operate from 3 V to 5.5 V, communicate at up to 250 kbit/s, and use a 16-pin SSOP footprint. It is particularly suitable for mixed-voltage embedded systems because it accepts 5 V logic inputs with a 3.3 V supply and includes ±15 kV HBM protection on the bus pins. The MAX3221IDBR is the closest same-package device-family option when its ordering, packaging, and lifecycle terms fit the production plan. Consider the SN65C3221EDBRG4 as a potential same-footprint second source, but approve it only after checking enable logic, timing, supply range, capacitor requirements, and ESD specifications in both manufacturer datasheets. Avoid multi-channel or different-footprint RS-232 devices when the PCB has only the MAX3221IDBRG4 land pattern.

Pembandingan dengan Alternatif

Parameter Umum Produk Ini MAX3221IDBR SN65C3221EDBRG4
Brand Texas Instruments Texas Instruments Texas Instruments
Package 16-pin SSOP 16-pin SSOP - same package 16-pin SSOP - same package
Device Type Single-channel RS-232 transceiver Single-channel RS-232 transceiver Single-channel RS-232 transceiver
Drivers 1 1 1
Receivers 1 1 1

Diferensiator Kunci

  • Single-channel RS-232 operation with integrated charge pump (vsSN65C3221EDBRG4)
  • Wide low-voltage supply compatibility (vsMAX3221IDBR)
  • Documented bus-pin ESD protection (vsSN65C3221EDBRG4)

Catatan Desain

Place the four 0.1 µF charge-pump capacitors immediately beside the MAX3221IDBRG4 capacitor pins, following the exact polarity and topology in the Texas Instruments datasheet. Keep each trace short and avoid routing sensitive signals beneath the charge-pump network. The pins should also be decoupled according to the manufacturer layout guidance. Correct placement reduces capacitor-loop area, supports stable charge-pump operation, and limits coupling of generated noise into adjacent circuitry.

Do not infer RS-232 pin compatibility from package size alone. Confirm the receiver-enable behavior, signal names, logic thresholds, supply range, and charge-pump connections for any proposed replacement. The MAX3221IDBR and SN65C3221EDBRG4 are confirmed same-package candidates, but a production substitution still requires comparison of the complete electrical specifications and application diagrams. Also verify whether the connected equipment expects DTE or DCE pinout and cable directionality.

Keep the RS-232 driver outputs and charge-pump nodes away from sensitive analog traces, clocks, and communication lines. Use a solid ground plane, provide a low-impedance chassis or signal-ground path at the connector, and route the cable-side interface according to the completed system's EMC strategy. The integrated ±15 kV HBM protection handles specified human-body-model ESD, but it does not replace surge protection for severe industrial cable environments.

Informasi Konformitas

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Bebas Logam Lengket
Unknown
Bebas Halogena
Unknown
Mineral Konflik
Unknown

The MAX3221 documentation identifies ±15 kV HBM ESD protection and compliance with TIA/EIA-232-F and ITU V.28. RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations were not established from the cited manufacturer and distributor records.

Pencarian Terkait

MAX3221IDBRG4 datasheet MAX3221IDBRG4 pinout MAX3221IDBRG4 datasheet pdf MAX3221IDBRG4 equivalent MAX3221IDBRG4 replacement MAX3221IDBRG4 cross reference MAX3221IDBRG4 vs SN65C3221EDBRG4 MAX3221IDBRG4 SSOP-16 footprint MAX3221IDBRG4 application circuit Texas Instruments MAX3221IDBRG4 MAX3221IDBRG4 price MAX3221IDBRG4 stock 250 kbit/s single RS-232 transceiver MAX3221IDBRG4 industrial RS-232

Komponen dan Istilah Terkait

Texas Instruments MAX3221IDBRG4 MAX3221IDBR SN65C3221EDBRG4 RS-232 RS-232 transceiver line driver line receiver interface IC semiconductor dual charge-pump TIA/EIA-232-F ITU V.28 ESD protection HBM 16-pin SSOP SSOP package family surface mount SMD 3.3 V UART 250 kbit/s ±15 kV ESD 1 µA standby current 0.1 µF charge-pump capacitor
Kutipan Cepat RFQ
Isi detail lengkap — tim penjualan kami akan membalas dalam 24 jam
Nomor Part Manufaktur Paket QTY Harga Target Lengkap
✓
Kutipan telah disubmit!

Kami akan membalas email Anda dalam 24 jam

1
RFQ Dikirim
2
Kutipan Diterima
3
Order Ditempatkan
4
Pembayaran
5
Dikirim
6
Dikirim
Lihat Detil RFQ