MAX3232MDBREP - 2/2 RS-232 Transceiver, 16-SSOP, +/-15kV ESD | TI
MPN: MAX3232MDBREP ✓ সক্রিয়MAX3232MDBREP সারাংশ
An RS-232 transceiver is a type of interface IC that converts logic-level TTL/CMOS signals into RS-232 bipolar levels and back again. In the signal-chain hierarchy, an RS-232 transceiver sits between an asynchronous communication controller (UART) and a physical serial-port connector, and it forms the electrical interface layer of the RS-232 standard (TIA/EIA-232-F and ITU V.28). The MAX3232 implements this function with integrated charge pumps, so no external RS-232 line-power supply is needed.
Key features of the MAX3232MDBREP include a 3 V to 5.5 V operating range, 250 kbps maximum data rate, 2 drivers and 2 receivers per package, and pin-to-pin ESD protection of +/-15 kV using the human-body model. It needs only four small external 0.1 uF charge-pump capacitors, and the SSOP (DB) package with a 5.30 mm body width saves board area over the classic SO-16 alternative.
Internally, the device uses a dual charge-pump topology that generates the positive and negative voltages required to swing an RS-232 signal beyond the logic rails. The enhanced (-EP) MAX3232 variant is the part that TI recommends for new designs where margin against ±15 kV ESD events is required, while the classic MAX3232 remains functionally compatible.
Typical applications include RS-232 ports on industrial control equipment, POS terminals, barcode scanners, serial-to-Ethernet gateways, security access readers, and legacy PC serial-port adapters, as well as level translation between 3.3 V UARTs and ±6 V RS-232 lines.
When laying out the board, place the four 0.1 uF charge-pump capacitors on the C1+, C1-, C2+, and C2- pins close to the pins, keep the bus traces away from the charge-pump nodes to avoid coupling noise into the RS-232 signal, and reserve a chassis or signal-ground connection path for surge current return.
This page consolidates parametric specifications, package and pin details, drop-in replacement options, and practical layout guidance into a single engineering reference, adding design context that the manufacturer datasheet does not cover in narrative form.
এর জন্য ড্রপ-ইন বিকল্প MAX3232MDBREP — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।
MAX3232ECDBR
✅ ড্রপ-ইনমূল্যের জন্য যোগাযোগ করুন
ডেটাশিট দেখুন →MAX3232MDBR
✅ ড্রপ-ইন ⚠️ স্পেক যাচাইকৃত নয়📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
MAX3232CDBR
✅ ড্রপ-ইন ⚠️ স্পেক যাচাইকৃত নয়মূল্যের জন্য যোগাযোগ করুন
ডেটাশিট দেখুন →MAX3232MDBREP বিশেষণ
| Number of Drivers/Receivers | 2/2 |
| Transceiver Type | Full RS232, 2 drivers / 2 receivers |
| Supply Voltage Range | 3 V to 5.5 V |
| Nominal Supply Voltage | 3.3 V to 5 V |
| Maximum Data Rate | 250 kbps |
| ESD Protection (Bus Pins) | +/-15 kV using HBM |
| Standards Compliance | TIA/EIA-232-F, ITU V.28 |
| প্যাকেজ | 16-SSOP (DB), 5.30 mm body width |
| পিন সংখ্যা | 16 |
| External Capacitors Required | 4 x 0.1 uF charge-pump capacitors |
| Charge Pump Topology | Dual charge-pump with on-chip voltage conversion |
| মাউন্টিং টাইপ | Surface Mount |
| Packaging | Tape and Reel (TR) |
| RoHS স্ট্যাটাস | Compliant |
MAX3232MDBREP পিন কনফিগারেশন
| পিন 1 | C1+ — Charge-pump flyback capacitor 1 positive node |
| পিন 2 | V+ — Charge-pump positive output node |
| পিন 3 | C1- — Charge-pump flyback capacitor 1 negative node |
| পিন 4 | C2+ — Charge-pump flyback capacitor 2 positive node |
| পিন 5 | C2- — Charge-pump flyback capacitor 2 negative node |
| পিন 6 | V- — Charge-pump negative output node |
| পিন 7 | R1OUT — Receiver 1 output (logic level) |
| পিন 8 | R2OUT — Receiver 2 output (logic level) |
| পিন 9 | T2IN — Driver 2 logic input |
| পিন 10 | T2OUT — Driver 2 RS-232 output |
| পিন 11 | T1IN — Driver 1 logic input |
| পিন 12 | T1OUT — Driver 1 RS-232 output |
| পিন 13 | R2IN — Receiver 2 RS-232 input |
| পিন 14 | R1IN — Receiver 1 RS-232 input |
| পিন 15 | GND — Ground |
| পিন 16 | VCC — Supply voltage input, 3 V to 5.5 V |
সাধারণ ব্যবহার
MAX3232MDBREP এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Industrial Control Panel RS-232 Port, Point-of-Sale Terminal and Barcode Scanner Interface, Serial-to-Ethernet Gateway, Access Control and Security Reader Interconnect, Instrumentation and Test Equipment Front Panel, Legacy PC and Retro-Fit Serial Adapter.
Industrial Control Panel RS-232 Port
The MAX3232MDBREP gives a 3.3 V or 5 V industrial controller a standards-compliant RS-232 port without adding a separate line-power supply. Its 2 drivers and 2 receivers support a console link plus one service port, and the 250 kbps rate covers both 115.2 kbps and 921.6 kbps baud settings. Because the serial pins carry +/-15 kV HBM ESD protection, connector-side handling during field installation is far safer than with unprotected logic drivers. The 16-pin SSOP (DB) footprint keeps the interface compact on a densely populated control board, and the on-chip dual charge pump needs only four external 0.1 uF capacitors.
সুপারিশকৃত
Point-of-Sale Terminal and Barcode Scanner Interface
Retail POS terminals and barcode scanners still rely on RS-232 for scale, reader and printer connectivity. The MAX3232MDBREP handles the 3 V to 5.5 V logic side from a low-power system-on-chip while generating the bipolar RS-232 swing internally, so only one supply rail is needed at the interface. The +/-15 kV HBM protection on bus pins including ground survives repeated plugging and unplugging of service connectors, a common source of field failures. Two drivers and two receivers per package allow the terminal to serve a printer port and a scanner port from one device when board space is tight.
সুপারিশকৃত
Serial-to-Ethernet Gateway
Gateway products must accept legacy RS-232 equipment and re-emit it over IP. The MAX3232MDBREP provides the physical interface with 250 kbps headroom, well beyond the 9.6 kbps to 115.2 kbps rates typical of industrial instruments, so a single transceiver can serve a high-speed configuration port and a slower legacy device. The small SSOP (DB) body, only 5.30 mm wide, leaves room for the Ethernet magnetics and processor in compact DIN-rail and wall-mount housings. Internal charge-pump conversion also simplifies the power tree, since the gateway needs only one logic rail at the interface.
সুপারিশকৃত
Access Control and Security Reader Interconnect
Door controllers, credential readers and intercoms are repeatedly connected and disconnected by users, which makes ESD immunity a primary design requirement. The MAX3232MDBREP provides +/-15 kV human-body-model protection on the serial-port connection pins including ground, protecting the controller UART from direct contact events. With two drivers and two receivers, one device can run a reader port and an intercom or alarm port simultaneously. The device operates from 3 V to 5.5 V, matching the narrow power budgets typical of access-control boards, and requires only four 0.1 uF charge-pump capacitors.
সুপারিশকৃত
Instrumentation and Test Equipment Front Panel
Laboratory and field test instruments expose RS-232 on the front panel for PC connection and legacy instrument control. The MAX3232MDBREP is a natural fit because its 250 kbps capability supports instrument control protocols faster than legacy serial, and its TIA/EIA-232-F and ITU V.28 compliance ensures interoperability with older analyzers and controllers. The 16-pin SSOP (DB) package frees front-panel board space for display and keypad routing, and the single 3 V to 5.5 V supply range lets the same PCB serve both benchtop and battery-portable instrument variants.
সুপারিশকৃত
Legacy PC and Retro-Fit Serial Adapter
Retrofit and industrial-PC designs frequently need to bridge a modern CPU to a DB9 or DB25 RS-232 connector that predates USB. The MAX3232MDBREP provides the converter in a single IC with no external line-power components, and its 250 kbps ceiling covers legacy IRQ-driven UART traffic without error. ESD protection at +/-15 kV HBM directly on the connector pins, including ground, is valuable when users attach unknown equipment. The small SSOP footprint allows the adapter to fit behind a compact panel-mount connector where a SOIC-16 part would not leave room for the shell.
সুপারিশকৃত
সুপারিশকৃত পণ্যের সারসংক্ষেপ
এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা MAX3232MDBREP — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।
নির্বাচন গাইড
বিকল্পের সাথে তুলনা
| পারামিটার | এই পণ্য | MAX3232ECDBR | MAX3232MDBR | MAX3232CDBR |
|---|---|---|---|---|
| Package | 16-SSOP (DB), 5.30 mm body width | 16-SSOP (DB) - same footprint | 16-SSOP (DB) - same footprint | 16-SSOP (DB) - same footprint |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Number of Drivers/Receivers | 2/2 | 2/2 | 2/2 | 2/2 |
| Supply Voltage Range | 3 V to 5.5 V | 3 V to 5.5 V | 3 V to 5.5 V | 3 V to 5.5 V |
| Maximum Data Rate | 250 kbps | 250 kbps | 250 kbps | 250 kbps |
| Standard Compliance | TIA/EIA-232-F, ITU V.28 | TIA/EIA-232-F, ITU V.28 | TIA/EIA-232-F, ITU V.28 | TIA/EIA-232-F, ITU V.28 |
| External Charge-Pump Capacitors | 4 x 0.1 uF | 4 x 0.1 uF | 4 x 0.1 uF | 4 x 0.1 uF |
| Product Grade | Enhanced product (-EP) | Enhanced product (MAX3232E) | Standard MAX3232 | Legacy standard grade |
| Packaging | Tape and Reel (TR) | Tape and Reel (TR) | Tape and Reel (TR) | Tape and Reel (TR) |
মূল পার্থক্যসমূহ
- Enhanced-product ESD margin in a compact SSOP footprint (বনামMAX3232MDBR)
- Higher data rate than legacy RS-232 transceivers of the same era (বনামMAX3232CDBR)
- Narrow package width for space-constrained boards (বনামMAX3232EIDW)
- Single-supply operation simplifies the power tree (বনামMAX3232CPE+)
ডিজাইন নোট
Place the four 0.1 uF charge-pump capacitors directly across the C1+, C1-, C2+ and C2- pins, with the ground-side connection returned to the device ground pin rather than to a distant star point. Keep these loops short and wide: long traces add ESR to the pumped supply and reduce the effective swing available on the RS-232 output. Route the bus-side nets T1OUT, T2OUT, R1IN and R2IN away from the charge-pump nodes so that the switched-capacitor ripple is not coupled into the differential signal path.
The MAX3232MDBREP charge pump switches internally at a frequency above the RS-232 signal band, but its harmonics can still appear on a poorly terminated bus. Terminate the RS-232 lines at the connector side and avoid long stubs or test pads that behave as unterminated transmission lines. For chassis-mounted equipment, provide a short, low-impedance path from the connector shell to chassis ground and keep the signal ground return separate from that path, so ESD and surge current is diverted away from the logic ground of the controller.
Do not substitute a SOIC-16 (SE) or PDIP-16 (PE) sibling onto an SSOP (DB) land pattern; the SSOP body is 5.30 mm wide while the SOIC body is about 3.9 mm, so the pads do not align and the pin numbering relative to the body differs. Also confirm the logic-level supply: the receiver thresholds are referenced to VCC, so a 5 V supply will not reliably detect 3.3 V driver levels from an external RS-232 receiver. Confirm the supply rail, package code and connector-side protection scheme before releasing the layout.
Estimated: with a 5 V supply, the MAX3232MDBREP charge pump and drivers draw a modest steady current from VCC plus a dynamic component proportional to the number of transitions on T1IN and T2IN. Budget the interface current separately from the host logic rail and keep a 0.1 uF bypass capacitor at pin 16 VCC plus a bulk capacitor near the connector-side return. If the same rail feeds a switching converter, place the RS-232 interface downstream of the converter but add local filtering so converter ripple does not modulate the RS-232 line amplitude.
কমপ্লায়েন্স তথ্য
RoHS compliance is stated on the Texas Instruments product documentation for this device. This is an industrial/communications interface IC and is not AEC-Q100 qualified; REACH, lead-free, halogen-free and conflict-minerals declarations were not found in the manufacturer pages reviewed.