Texas Instruments

MAX3232MDBREP - 2/2 RS-232 Transceiver, 16-SSOP, +/-15kV ESD | TI

MPN: MAX3232MDBREP ✓ Aktif
3 V to 5.5 V Vdss TIA/EIA-232-F, ITU V.28 Rds(on) 16-SSOP (DB), 5.30 mm body width Package
MOQ: 1 |

MAX3232MDBREP Ringkasan

The Texas Instruments MAX3232MDBREP is a dual RS-232 line driver and dual line receiver transceiver with on-chip charge-pump voltage conversion, operating from a 3 V to 5.5 V single supply and packaged in a 16-pin SSOP (DB) package. It delivers data rates up to 250 kbps and provides +/-15 kV human-body-model ESD protection on all bus pins, including ground.

An RS-232 transceiver is a type of interface IC that converts logic-level TTL/CMOS signals into RS-232 bipolar levels and back again. In the signal-chain hierarchy, an RS-232 transceiver sits between an asynchronous communication controller (UART) and a physical serial-port connector, and it forms the electrical interface layer of the RS-232 standard (TIA/EIA-232-F and ITU V.28). The MAX3232 implements this function with integrated charge pumps, so no external RS-232 line-power supply is needed.

Key features of the MAX3232MDBREP include a 3 V to 5.5 V operating range, 250 kbps maximum data rate, 2 drivers and 2 receivers per package, and pin-to-pin ESD protection of +/-15 kV using the human-body model. It needs only four small external 0.1 uF charge-pump capacitors, and the SSOP (DB) package with a 5.30 mm body width saves board area over the classic SO-16 alternative.

Internally, the device uses a dual charge-pump topology that generates the positive and negative voltages required to swing an RS-232 signal beyond the logic rails. The enhanced (-EP) MAX3232 variant is the part that TI recommends for new designs where margin against ±15 kV ESD events is required, while the classic MAX3232 remains functionally compatible.

Typical applications include RS-232 ports on industrial control equipment, POS terminals, barcode scanners, serial-to-Ethernet gateways, security access readers, and legacy PC serial-port adapters, as well as level translation between 3.3 V UARTs and ±6 V RS-232 lines.

When laying out the board, place the four 0.1 uF charge-pump capacitors on the C1+, C1-, C2+, and C2- pins close to the pins, keep the bus traces away from the charge-pump nodes to avoid coupling noise into the RS-232 signal, and reserve a chassis or signal-ground connection path for surge current return.

This page consolidates parametric specifications, package and pin details, drop-in replacement options, and practical layout guidance into a single engineering reference, adding design context that the manufacturer datasheet does not cover in narrative form.

Alternatif penggantian untuk MAX3232MDBREP — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.

MAX3232ECDBR

✅ Drop-In
Texas Instruments
📦 16-SSOP (DB)
RS-232 · Transceiver · 2 · 2 · 3 V to 5.5 V · 250 kbps (minimum) · ±15 kV (HBM) · ±15 kV contact discharge / ±15 kV air-gap discharge

Kontak untuk harga

Lihat Datasheet →

MAX3232MDBR

✅ Drop-In ⚠️ Spesifikasi Tidak Disahkan
📦 16-SSOP (DB)
Identical DB SSOP footprint and 2/2 RS-232 function at 3 V to 5.5 V and 250 kbps; standard rather than -EP enhanced product, so ESD margin over the +/-15 kV HBM rating is lower

📋 Alternatif referensi (tidak dalam katalog)

MAX3232CDBR

✅ Drop-In ⚠️ Spesifikasi Tidak Disahkan
Texas Instruments
📦 16-SSOP (DB)
RS-232 line driver/receiver transceiver · 2 · 2 · 3 V to 5.5 V · 250 kbit/s · 5 V logic · 300 uA · 0.1 uF

Kontak untuk harga

Lihat Datasheet →

MAX3232MDBREP Spesifikasi

Number of Drivers/Receivers 2/2
Transceiver Type Full RS232, 2 drivers / 2 receivers
Supply Voltage Range 3 V to 5.5 V
Nominal Supply Voltage 3.3 V to 5 V
Maximum Data Rate 250 kbps
ESD Protection (Bus Pins) +/-15 kV using HBM
Standards Compliance TIA/EIA-232-F, ITU V.28
Paket 16-SSOP (DB), 5.30 mm body width
Jumlah Pin 16
External Capacitors Required 4 x 0.1 uF charge-pump capacitors
Charge Pump Topology Dual charge-pump with on-chip voltage conversion
Tipe Mounting Surface Mount
Packaging Tape and Reel (TR)
Status RoHS Compliant

Konfigurasi Pin MAX3232MDBREP

SSOP-16 Package Pinout Diagram SSOP-16 3.9x6.0mm, P0.635mm, JEDEC MO-150. 1 16 2 15 3 14 4 13 5 12 6 11 7 10 8 9 SSOP-16
Pin produk 1 C1+ — Charge-pump flyback capacitor 1 positive node
Pin produk 2 V+ — Charge-pump positive output node
Pin produk 3 C1- — Charge-pump flyback capacitor 1 negative node
Pin produk 4 C2+ — Charge-pump flyback capacitor 2 positive node
Pin produk 5 C2- — Charge-pump flyback capacitor 2 negative node
Pin produk 6 V- — Charge-pump negative output node
Pin produk 7 R1OUT — Receiver 1 output (logic level)
Pin produk 8 R2OUT — Receiver 2 output (logic level)
Pin produk 9 T2IN — Driver 2 logic input
Pin produk 10 T2OUT — Driver 2 RS-232 output
Pin produk 11 T1IN — Driver 1 logic input
Pin produk 12 T1OUT — Driver 1 RS-232 output
Pin produk 13 R2IN — Receiver 2 RS-232 input
Pin produk 14 R1IN — Receiver 1 RS-232 input
Pin produk 15 GND — Ground
Pin produk 16 VCC — Supply voltage input, 3 V to 5.5 V

Aplikasi Umum

MAX3232MDBREP cocok untuk 6 aplikasis: Industrial Control Panel RS-232 Port, Point-of-Sale Terminal and Barcode Scanner Interface, Serial-to-Ethernet Gateway, Access Control and Security Reader Interconnect, Instrumentation and Test Equipment Front Panel, Legacy PC and Retro-Fit Serial Adapter.

🏭

Industrial Control Panel RS-232 Port

The MAX3232MDBREP gives a 3.3 V or 5 V industrial controller a standards-compliant RS-232 port without adding a separate line-power supply. Its 2 drivers and 2 receivers support a console link plus one service port, and the 250 kbps rate covers both 115.2 kbps and 921.6 kbps baud settings. Because the serial pins carry +/-15 kV HBM ESD protection, connector-side handling during field installation is far safer than with unprotected logic drivers. The 16-pin SSOP (DB) footprint keeps the interface compact on a densely populated control board, and the on-chip dual charge pump needs only four external 0.1 uF capacitors.

🏭

Point-of-Sale Terminal and Barcode Scanner Interface

Retail POS terminals and barcode scanners still rely on RS-232 for scale, reader and printer connectivity. The MAX3232MDBREP handles the 3 V to 5.5 V logic side from a low-power system-on-chip while generating the bipolar RS-232 swing internally, so only one supply rail is needed at the interface. The +/-15 kV HBM protection on bus pins including ground survives repeated plugging and unplugging of service connectors, a common source of field failures. Two drivers and two receivers per package allow the terminal to serve a printer port and a scanner port from one device when board space is tight.

🌐

Serial-to-Ethernet Gateway

Gateway products must accept legacy RS-232 equipment and re-emit it over IP. The MAX3232MDBREP provides the physical interface with 250 kbps headroom, well beyond the 9.6 kbps to 115.2 kbps rates typical of industrial instruments, so a single transceiver can serve a high-speed configuration port and a slower legacy device. The small SSOP (DB) body, only 5.30 mm wide, leaves room for the Ethernet magnetics and processor in compact DIN-rail and wall-mount housings. Internal charge-pump conversion also simplifies the power tree, since the gateway needs only one logic rail at the interface.

🎥

Access Control and Security Reader Interconnect

Door controllers, credential readers and intercoms are repeatedly connected and disconnected by users, which makes ESD immunity a primary design requirement. The MAX3232MDBREP provides +/-15 kV human-body-model protection on the serial-port connection pins including ground, protecting the controller UART from direct contact events. With two drivers and two receivers, one device can run a reader port and an intercom or alarm port simultaneously. The device operates from 3 V to 5.5 V, matching the narrow power budgets typical of access-control boards, and requires only four 0.1 uF charge-pump capacitors.

🔧

Instrumentation and Test Equipment Front Panel

Laboratory and field test instruments expose RS-232 on the front panel for PC connection and legacy instrument control. The MAX3232MDBREP is a natural fit because its 250 kbps capability supports instrument control protocols faster than legacy serial, and its TIA/EIA-232-F and ITU V.28 compliance ensures interoperability with older analyzers and controllers. The 16-pin SSOP (DB) package frees front-panel board space for display and keypad routing, and the single 3 V to 5.5 V supply range lets the same PCB serve both benchtop and battery-portable instrument variants.

🖥️

Legacy PC and Retro-Fit Serial Adapter

Retrofit and industrial-PC designs frequently need to bridge a modern CPU to a DB9 or DB25 RS-232 connector that predates USB. The MAX3232MDBREP provides the converter in a single IC with no external line-power components, and its 250 kbps ceiling covers legacy IRQ-driven UART traffic without error. ESD protection at +/-15 kV HBM directly on the connector pins, including ground, is valuable when users attach unknown equipment. The small SSOP footprint allows the adapter to fit behind a compact panel-mount connector where a SOIC-16 part would not leave room for the shell.

What is the MAX3232MDBREP?
The MAX3232MDBREP is a Texas Instruments dual RS-232 line driver and dual line receiver transceiver with integrated charge-pump voltage conversion, supplied in a 16-pin SSOP (DB) package. According to the MAX3232-EP datasheet, the device operates from a single 3 V to 5.5 V supply, supports data rates up to 250 kbps, and provides +/-15 kV human-body-model ESD protection pin-to-pin on the serial-port connection pins including ground. It interfaces directly between an asynchronous communication controller and an RS-232 connector without an external line-power supply.
What is the operating voltage range of MAX3232MDBREP?
The MAX3232MDBREP operates from 3 V to 5.5 V, making it usable directly from 3.3 V and 5 V rails. The manufacturer describes it as a 3-V to 5.5-V multichannel RS-232 line driver/receiver, and the charge-pump and driver architecture means the RS-232 bipolar swing is generated internally regardless of the logic supply level. This lets a single board host a 3.3 V UART and a legacy RS-232 port without level-shifting logic families separately.
How fast can MAX3232MDBREP transmit data?
The MAX3232MDBREP supports a maximum data rate of 250 kbps, which is well above the standard 9600, 19.2 kbps, 115.2 kbps, and 921.6 kbps RS-232 port rates used in most industrial and commercial equipment. Its dual charge-pump design supplies the bipolar line voltage needed for reliable signalling at these rates, so a single device can serve both a legacy data port and a higher-speed diagnostic or firmware channel on the same board.
What is the difference between MAX3232MDBREP and MAX3232E?
The MAX3232MDBREP is the enhanced-product version of the MAX3232 family, and the two are pin-compatible with essentially identical electrical function: 2 drivers, 2 receivers, 3 V to 5.5 V supply, and 250 kbps data rate. The key difference is the level of on-chip protection and process maturity in the enhanced part, which is the variant TI recommends for new designs. Because the pinout and function set match, MAX3232E-based parts in the same package can be substituted where supply conditions require.
Where can I download the MAX3232MDBREP datasheet PDF?
The MAX3232MDBREP datasheet is available from the Texas Instruments MAX3232-EP product page and its part-details listing for MAX3232MDBREP, and the same PDF is mirrored on parts aggregator sites such as alldatasheet and datasheets.com. The document describes a 3-V to 5.5-V multichannel RS-232 line driver/receiver with +/-15-kV ESD protection and is 14 pages in length. Use the pin-description table and typical application circuit in that document when assigning PCB tracks and selecting the charge-pump capacitors.
Where can I find the MAX3232MDBREP pinout?
The MAX3232MDBREP pinout is given in the pin-configuration section of the manufacturer datasheet for the 16-pin SSOP (DB) package. The device uses the standard MAX3232 arrangement: pins 1 to 6 are the charge-pump network (C1+, V+, C1-, C2+, C2-, V-), pins 7 and 8 are R1OUT and R2OUT, pins 9 to 12 are T2IN, T2OUT, T1IN and T1OUT, pins 13 and 14 are R2IN and R1IN, pin 15 is GND and pin 16 is VCC.
How many external capacitors does MAX3232MDBREP need?
The MAX3232MDBREP requires four small external 0.1 uF capacitors to complete its dual charge-pump circuit, connected to the C1+, C1-, C2+ and C2- pins with V+ and V- on the remaining charge-pump nodes. The manufacturer describes the topology as a dual charge-pump circuit with four small external capacitors. Keep these components close to the corresponding pins because long trace lengths add ESR and reduce the effectiveness of the pumped supply.
Can MAX3232MDBREP replace MAX3232IPW on an existing PCB?
The MAX3232MDBREP can replace a MAX3232IPW only if the footprint is changed, because MAX3232IPW is a 16-pin SOIC while MAX3232MDBREP is a 16-pin SSOP with a wider 5.30 mm body. Within the SSOP (DB) footprint, however, the MAX3232E and MAX3232 variants are true pin-to-pin drop-ins with identical charge-pump and driver/receiver pin assignments, so the same board revision can move between the standard and enhanced parts without a layout change.
What is the best drop-in replacement for MAX3232MDBREP?
The closest drop-in replacement is the MAX3232ECDBR, which uses the identical 16-pin SSOP (DB) footprint with the same 2/2 driver-receiver arrangement, 3 V to 5.5 V supply range and 250 kbps data rate. It is the enhanced-product MAX3232E variant in the same package, making it a like-for-like substitution. When sourcing alternatives, match the package code and pin count first, because SOIC (SE/DW) and PDIP (PE) siblings cannot be soldered onto an SSOP land pattern without board rework.
Is MAX3232MDBREP the same as SN65C3232?
The MAX3232MDBREP and the SN65C3232 are functionally similar 2/2 RS-232 transceivers, but they are not footprint-compatible for an SSOP board. The SN65C3232 is offered in the narrow SOIC-16 (DG) package while the MAX3232MDBREP uses the wider SSOP-16 (DB) package, so a direct substitution would require a new PCB footprint and a different pin location for the ground and driver/receiver pins. Treat the SN65C3232 family as a functional alternative for a fresh design, not a drop-in replacement.
When should I choose MAX3232MDBREP over MAX3232E in the SOIC package?
Choose the MAX3232MDBREP when board area is tight and you want the enhanced-product ESD robustness of the -EP family, because the 16-pin SSOP (DB) body is only 5.30 mm wide versus the ~3.9 mm SOIC body, yet it carries a 250 kbps data rate and +/-15 kV HBM protection. Choose the MAX3232E in the SOIC (SE) package when your existing board layout was built around the narrow SOIC footprint and you do not need to reclaim board area. Both are 3 V to 5.5 V, 2/2 transceivers with the same charge-pump pin pattern.
Is MAX3232MDBREP suitable for industrial equipment?
The MAX3232MDBREP suits industrial serial-port equipment because it meets TIA/EIA-232-F and ITU V.28 signalling requirements, tolerates 3 V to 5.5 V supply variation common in industrial rails, and provides +/-15 kV HBM ESD protection on the connector-side pins. Its 250 kbps capability also allows a single device to serve a control port and a higher-speed service or firmware port. For temperature extremes or radiated/conducted industrial immunity beyond HBM, specify the variant with the temperature grade your enclosure requires.
How do I protect the RS-232 lines when using MAX3232MDBREP?
Use the MAX3232MDBREP as the line driver but add board-level protection for the connector, because HBM-rated on-chip protection does not replace a surge or TVS array at the connector. Keep the RS-232 traces short, route them away from the charge-pump nodes C1+, C1-, C2+ and C2-, and provide a low-impedance return path to chassis or signal ground so ESD and surge current does not flow through sensitive logic ground. A series resistor of 22 ohm to 100 ohm in each driver line also limits fault current to the ESD structures.
What are the key specifications of MAX3232MDBREP that engineers should know?
The MAX3232MDBREP is a 2-driver/2-receiver full RS-232 transceiver running from a 3 V to 5.5 V supply at up to 250 kbps, in a 16-pin SSOP (DB) package with tape-and-reel packaging. Its on-chip dual charge pump needs only four external 0.1 uF capacitors, and the serial-port pins carry +/-15 kV human-body-model ESD protection. The device meets TIA/EIA-232-F and ITU V.28 requirements, and it is the enhanced-product (-EP) member of the MAX3232 family that TI recommends for new designs.
Where can I buy MAX3232MDBREP online?
The MAX3232MDBREP is stocked in volume by major authorized distributors, and XAIPART also lists the part with a Request a Quote form on this page for current pricing, stock and lead time. Use the Request a Quote form on this page to obtain a committed price and delivery schedule for your quantities, including reel quantities and scheduled deliveries, since distributor pricing and inventory move continuously. For full technical confirmation, reference the MAX3232-EP datasheet and the TI part-details page for MAX3232MDBREP.
What is the lead time and typical order quantity for MAX3232MDBREP?
The MAX3232MDBREP ships in tape-and-reel packaging, which is the standard production format for this 16-pin SSOP device and is normally supplied in full reels. Current lead time and minimum order quantity change with demand and inventory position, so request the latest figure through the Request a Quote form on this page rather than relying on a static value. Provide your reel quantity, date code requirement and target ship date so the manufacturer or authorized channel can commit a schedule.
Can MAX3232MDBREP drive an RS-232 port with a 3.3 V UART?
Yes, the MAX3232MDBREP accepts 3.3 V logic levels while running from a 3 V to 5.5 V supply, so it can be paired directly with a 3.3 V microcontroller or SoC UART. The internal charge pump generates the RS-232 bipolar line voltage independently of the logic level swing, so the receiver thresholds stay compatible with TIA/EIA-232-F signalling. Keep the logic-side traces short and away from the connector-side bus pins to prevent coupling from the high-voltage swing back into the UART pins.
What is the best equivalent MAX3232 family part for MAX3232MDBREP?
The MAX3232ECDBR is the best equivalent for the MAX3232MDBREP because it shares the 16-pin SSOP (DB) package and the identical 2/2 driver-receiver, 3 V to 5.5 V, 250 kbps electrical configuration with the same charge-pump pin arrangement. For a functional rather than drop-in choice on a redesigned board, the SN65C3232 in SOIC-16 and the MAX3232E family in SOIC-16 or PDIP-16 offer the same RS-232 function in different packages. Confirm the package code before committing to any substitution.

Data referensi engineering untuk MAX3232MDBREP — pembandingan, panduan desain, dan informasi konformitas.

Panduan Pemilihan

Choose the MAX3232MDBREP when your design needs an RS-232 port on a 16-pin SSOP land pattern, a 3 V to 5.5 V single supply, and the enhanced-product ESD robustness of +/-15 kV HBM on the connector pins. Pick MAX3232ECDBR when you want the MAX3232E enhanced silicon in the same DB package, which is a like-for-like substitution when sourcing flexibility matters. Choose MAX3232MDBR only if you have a legacy board already qualified around the standard MAX3232 grade, and you accept its lower ESD margin. Move to MAX3232EIDW or another SOIC-16 (DW) part only if your PCB is already built around the narrow SOIC footprint; the DB and DW packages are not footprint-compatible and require different boards. For a fresh board with no legacy constraint, validate the SSOP (DB) option first because it preserves the most board area. If your interface must survive surge events rather than only ESD, add a dedicated TVS array at the connector, since HBM-rated on-chip protection does not replace that stage.

Pembandingan dengan Alternatif

Parameter Umum Produk Ini MAX3232ECDBR MAX3232MDBR MAX3232CDBR
Package 16-SSOP (DB), 5.30 mm body width 16-SSOP (DB) - same footprint 16-SSOP (DB) - same footprint 16-SSOP (DB) - same footprint
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Number of Drivers/Receivers 2/2 2/2 2/2 2/2
Supply Voltage Range 3 V to 5.5 V 3 V to 5.5 V 3 V to 5.5 V 3 V to 5.5 V
Maximum Data Rate 250 kbps 250 kbps 250 kbps 250 kbps
Standard Compliance TIA/EIA-232-F, ITU V.28 TIA/EIA-232-F, ITU V.28 TIA/EIA-232-F, ITU V.28 TIA/EIA-232-F, ITU V.28
External Charge-Pump Capacitors 4 x 0.1 uF 4 x 0.1 uF 4 x 0.1 uF 4 x 0.1 uF
Product Grade Enhanced product (-EP) Enhanced product (MAX3232E) Standard MAX3232 Legacy standard grade
Packaging Tape and Reel (TR) Tape and Reel (TR) Tape and Reel (TR) Tape and Reel (TR)

Diferensiator Kunci

  • Enhanced-product ESD margin in a compact SSOP footprint (vsMAX3232MDBR)
  • Higher data rate than legacy RS-232 transceivers of the same era (vsMAX3232CDBR)
  • Narrow package width for space-constrained boards (vsMAX3232EIDW)
  • Single-supply operation simplifies the power tree (vsMAX3232CPE+)

Catatan Desain

Place the four 0.1 uF charge-pump capacitors directly across the C1+, C1-, C2+ and C2- pins, with the ground-side connection returned to the device ground pin rather than to a distant star point. Keep these loops short and wide: long traces add ESR to the pumped supply and reduce the effective swing available on the RS-232 output. Route the bus-side nets T1OUT, T2OUT, R1IN and R2IN away from the charge-pump nodes so that the switched-capacitor ripple is not coupled into the differential signal path.

The MAX3232MDBREP charge pump switches internally at a frequency above the RS-232 signal band, but its harmonics can still appear on a poorly terminated bus. Terminate the RS-232 lines at the connector side and avoid long stubs or test pads that behave as unterminated transmission lines. For chassis-mounted equipment, provide a short, low-impedance path from the connector shell to chassis ground and keep the signal ground return separate from that path, so ESD and surge current is diverted away from the logic ground of the controller.

Do not substitute a SOIC-16 (SE) or PDIP-16 (PE) sibling onto an SSOP (DB) land pattern; the SSOP body is 5.30 mm wide while the SOIC body is about 3.9 mm, so the pads do not align and the pin numbering relative to the body differs. Also confirm the logic-level supply: the receiver thresholds are referenced to VCC, so a 5 V supply will not reliably detect 3.3 V driver levels from an external RS-232 receiver. Confirm the supply rail, package code and connector-side protection scheme before releasing the layout.

Estimated: with a 5 V supply, the MAX3232MDBREP charge pump and drivers draw a modest steady current from VCC plus a dynamic component proportional to the number of transitions on T1IN and T2IN. Budget the interface current separately from the host logic rail and keep a 0.1 uF bypass capacitor at pin 16 VCC plus a bulk capacitor near the connector-side return. If the same rail feeds a switching converter, place the RS-232 interface downstream of the converter but add local filtering so converter ripple does not modulate the RS-232 line amplitude.

Informasi Konformitas

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
Bebas Logam Lengket
Unknown
Bebas Halogena
Unknown
Mineral Konflik
Unknown

RoHS compliance is stated on the Texas Instruments product documentation for this device. This is an industrial/communications interface IC and is not AEC-Q100 qualified; REACH, lead-free, halogen-free and conflict-minerals declarations were not found in the manufacturer pages reviewed.

Data disahkan pada: 2026-11-09 — data disahkan dan disusun oleh tim engineering komponen XAIPART

Pencarian Terkait

max3232mdbrep data sheet MAX3232MDBREP datasheet pdf MAX3232MDBREP pinout MAX3232MDBREP 16-SSOP package Texas Instruments MAX3232MDBREP MAX3232MDBREP equivalent MAX3232MDBREP drop-in replacement MAX3232MDBREP vs MAX3232ECDBR MAX3232 cross reference SSOP DB MAX3232MDBREP price MAX3232MDBREP stock RS-232 2/2 transceiver 3V to 5.5V 250kbps MAX3232 charge pump capacitor layout RS-232 transceiver 16-SSOP for industrial port

Komponen dan Istilah Terkait

Texas Instruments MAX3232MDBREP MAX3232ECDBR MAX3232MDBR MAX3232CDBR MAX3232E RS-232 transceiver line driver line receiver interface IC charge pump TIA/EIA-232-F ITU V.28 ESD protection human body model (HBM) SSOP-16 DB package surface mount SMD RoHS 3.3 V UART 250 kbps industrial control panel serial-to-Ethernet gateway
Kutipan Cepat RFQ
Isi detail lengkap — tim penjualan kami akan membalas dalam 24 jam
Nomor Part Manufaktur Paket QTY Harga Target Lengkap
✓
Kutipan telah disubmit!

Kami akan membalas email Anda dalam 24 jam

1
RFQ Dikirim
2
Kutipan Diterima
3
Order Ditempatkan
4
Pembayaran
5
Dikirim
6
Dikirim
Lihat Detil RFQ