MAX3243EEAI+G1Z - 250kbps RS-232 Transceiver | Maxim
MPN: MAX3243EEAI+G1Z ✓ সক্রিয়MAX3243EEAI+G1Z সারাংশ
An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 voltage levels and converts incoming RS-232 signals back into digital logic levels. It belongs to the serial-interface hierarchy: transceiver > RS-232 interface > communications interface > interface IC. This bidirectional signal-conditioning function allows equipment operating at different logic levels to communicate through the EIA/TIA-232 physical interface.
The MAX3243EEAI+G1Z combines three driver outputs with five receiver inputs, supporting applications that need multiple receive channels and a smaller number of transmit channels. Its 3.0 V to 5.5 V supply range accommodates modern 3.3 V and 5 V digital systems. The 250 kbps maximum data rate is suitable for moderate-speed serial links, including embedded control, instrumentation, and industrial communications equipment.
Automatic shutdown is a defining feature of the MAX3243E family. When no valid receiver signal is detected, the on-board power supply and drivers can shut down to reduce supply current to as little as 1 µA. Automatic wake-up reactivates the interface when valid data returns, reducing system power consumption without requiring host intervention.
Enhanced ESD protection strengthens the interface against electrostatic discharge encountered during cable installation or industrial environments. According to the MAX3243EEAI data-sheet description, transmitter outputs and receiver inputs support ±15 kV air-gap discharge and ±8 kV contact-discharge protection. These ratings are relevant to external cable-facing pins and should be considered alongside normal board-layout and grounding practices.
Typical uses include RS-232 links in industrial controllers, test equipment, data-acquisition systems, point-of-sale hardware, and embedded serial-port systems. The 28-pin SSOP package is compact, but its lead pitch and thermal behavior require careful PCB planning. Use the manufacturer pin-description table when assigning tracks and confirming the exposed-package or thermal details for the selected ordering code.
This page combines the family-level electrical characteristics, exact package identification, sourcing guidance, application fit, and practical design considerations. It also identifies genuine same-family alternatives while making the differences between ordering variants explicit for engineering review.
এর জন্য ড্রপ-ইন বিকল্প MAX3243EEAI+G1Z — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।
এই সিরিজের ভ্যারিয়েন্ট
একই সিরিজের মডেল যেগুলো drop-in compatible MAX3243EEAI+G1Z (একই form factor এবং footprint) — পার্থক্য রয়েছে Maximum Data Rate, Package, Product Type, Receiver Count, Supply Voltage Range.
MAX3243EAI+G1Z
✅ ড্রপ-ইন ⚠️ স্পেক যাচাইকৃত নয়মূল্যের জন্য যোগাযোগ করুন
ডেটাশিট দেখুন →MAX3243EAI+TG1Z
✅ ড্রপ-ইন ⚠️ স্পেক যাচাইকৃত নয়মূল্যের জন্য যোগাযোগ করুন
ডেটাশিট দেখুন →MAX3243EEAI+TG071
✅ ড্রপ-ইন ⚠️ স্পেক যাচাইকৃত নয়📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
MAX3243EEUI+T
✅ ড্রপ-ইন ⚠️ স্পেক যাচাইকৃত নয়মূল্যের জন্য যোগাযোগ করুন
ডেটাশিট দেখুন →MAX3237EAI+
✅ ড্রপ-ইন📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
MAX3243EEAI+G1Z বিশেষণ
| Product Type | 3/5 RS-232 transceiver |
| Transmitter Count | 3 |
| Receiver Count | 5 |
| Supply Voltage Range | 3.0 V to 5.5 V |
| Maximum Data Rate | 250 kbps |
| AutoShutdown Supply Current | 1 µA |
| Air-Gap ESD Protection | ±15 kV |
| Contact-Discharge ESD Protection | ±8 kV |
| প্যাকেজ | 28-pin SSOP |
| মাউন্টিং টাইপ | Surface mount |
| Interface Standard | EIA/TIA-232 and V.28/V.24 |
MAX3243EEAI+G1Z 28-pin ssop পিন কনফিগারেশন গাইড
MAX3243EEAI+G1Z (28-pin ssop প্যাকেজ)-এর পিন কনফিগারেশন। পিন নম্বরিং, ফাংশন এবং সংযোগ ডায়াগ্রাম প্রস্তুতকারকের ডেটাশিটে সংজ্ঞায়িত করা আছে। সঠিক ফুটপ্রিন্ট এবং সোল্ডারিং নির্দেশিকার জন্য এটি দেখুন।
এর জন্য বিস্তারিত পিনআউট ডেটা পাওয়া যায়নি MAX3243EEAI+G1Z.
দেখুন ডেটাশিট সম্পূর্ণ পিন কনফিগারেশনের জন্য।
সাধারণ ব্যবহার
MAX3243EEAI+G1Z এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Industrial Serial Controllers, Test and Measurement Equipment, Data-Acquisition Systems, Point-of-Sale and Retail Terminals, Embedded Serial Communication, Security and Access-Control Systems.
Industrial Serial Controllers
The MAX3243EEAI+G1Z suits industrial controllers that must expose several RS-232 receive channels while transmitting status or commands on fewer lines. Its three transmitters, five receivers, 250 kbps maximum rate, and 3.0 V to 5.5 V operating range support both 3.3 V and 5 V control electronics. Automatic shutdown reduces the 1 µA-level idle current when no valid receiver activity is detected. The 28-pin SSOP conserves board area, although cable routing should remain short and away from high-current switching nodes.
সুপারিশকৃত
Test and Measurement Equipment
The MAX3243EEAI+G1Z can connect laboratory and field-test equipment to legacy RS-232 instruments that require multiple receive inputs. Its 250 kbps rate is appropriate for command and measurement-data transfers, while the five receivers can monitor several control or status lines from one interface. The low shutdown current benefits portable instruments that spend substantial time between test sequences. Place the transceiver near the connector, maintain a common signal ground, and route the cable-side traces away from sensitive analog and reference circuitry.
সুপারিশকৃত
Data-Acquisition Systems
The MAX3243EEAI+G1Z is appropriate for data-acquisition controllers communicating with external sensors, laboratory modules, or service equipment over RS-232. Five receiver channels support multiple status inputs, and the three drivers can carry commands or trigger signals. The 3.0 V to 5.5 V supply range permits operation from common embedded rails. The 250 kbps ceiling supports moderate-rate command and status traffic but should be checked against cable capacitance and timing margins. Automatic wake-up helps reduce standby demand when the acquisition system polls its instruments intermittently.
সুপারিশকৃত
Point-of-Sale and Retail Terminals
Retail terminals can use the MAX3243EEAI+G1Z to interface a controller with RS-232 peripherals such as scales, printers, or magnetic-reader equipment. The combination of three transmitters and five receivers supports command output plus multiple peripheral-status inputs. Operation from 3.3 V or 5 V simplifies integration with embedded checkout hardware, and the AutoShutdown behavior limits consumption during inactive periods. Place surge and ESD protection strategy around the external connector, and verify that ground references meet the requirements of the connected peripherals.
সুপারিশকৃত
Embedded Serial Communication
The MAX3243EEAI+G1Z provides a compact bridge between an embedded processor and an RS-232 port in the 28-pin SSOP package. A 3.0 V to 5.5 V supply range allows direct operation from common embedded rails, while the 250 kbps rate covers many configuration, logging, and control protocols. Five receiver inputs can accept several status signals without requiring separate digital input buffers. Automatic shutdown and wake-up are especially useful in duty-cycled systems, although firmware must tolerate the receiver's signaling and transition behavior documented by the manufacturer.
সুপারিশকৃত
Security and Access-Control Systems
The MAX3243EEAI+G1Z can support access-control readers, alarm panels, and configuration tools that exchange RS-232 commands and status signals. Three transmit channels can serve separate reader or panel ports, while five receive channels can monitor door, alarm, and acknowledgment signals. The enhanced ±15 kV air-gap and ±8 kV contact ESD ratings are useful at externally accessible cable interfaces, although enclosure and installation practices remain essential. The automatic low-power state can also reduce consumption in sparsely accessed or intermittently networked installations.
সুপারিশকৃত
সুপারিশকৃত পণ্যের সারসংক্ষেপ
এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা MAX3243EEAI+G1Z — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।
নির্বাচন গাইড
বিকল্পের সাথে তুলনা
| পারামিটার | এই পণ্য | MAX3243EAI+G1Z | MAX3243EAI+TG1Z | MAX3243EEAI+TG071 | MAX3243EEUI+T | MAX3237EAI+ |
|---|---|---|---|---|---|---|
| Brand | Maxim Integrated | Maxim Integrated | Maxim Integrated | Maxim Integrated | Maxim Integrated | Maxim Integrated |
| Package | 28-pin SSOP | 28-pin SSOP | 28-pin SSOP | 28-pin SSOP | 28-pin SSOP | 28-pin SSOP |
| Transmitter Count | 3 | 3 | 3 | 3 | 3 | 3 |
| Receiver Count | 5 | 5 | 5 | 5 | 5 | 3 |
| Maximum Data Rate | 250 kbps | 250 kbps | 250 kbps | 250 kbps | 250 kbps | 250 kbps |
| Exact Ordering Grade | EEAI+G1Z | EAI+G1Z | EAI+TG1Z | EEAI+TG071 | EEUI+T | EAI+ |
মূল পার্থক্যসমূহ
- Five receivers provide greater input-channel capacity (বনামMAX3237EAI+)
- Exact ordering configuration for MAX3243EEAI-family designs (বনামMAX3243EAI+G1Z)
- Low-power automatic shutdown supports duty-cycled interfaces (বনামMAX3237EAI+)
ডিজাইন নোট
Do not infer that every MAX3243E-family suffix is electrically interchangeable. The MAX3243EEAI+G1Z is a specific ordering variant in a 28-pin SSOP family, while related E, EE, UI, and TG codes can identify different temperature grades, qualification levels, or packaging options. Before substitution, compare the complete ordering table, operating-temperature limits, exposed-terminal details, and lifecycle status against the original design requirements.
Place the MAX3243EEAI+G1Z close to the RS-232 connector and route driver outputs and receiver inputs as short, impedance-controlled traces where practical. Keep the transceiver and its charge-pump or support components away from sensitive analog inputs. Route the connector ground directly to the interface ground reference, and avoid sharing narrow ground paths with motors, relays, or switching-power stages that could disturb the receiver threshold.
The enhanced ±15 kV air-gap and ±8 kV contact-discharge ratings protect the interface pins under specified ESD test conditions, but they do not eliminate radiated or conducted emissions from attached equipment. Use the recommended bypass capacitance and support-component layout from the manufacturer data sheet. Keep external cables away from switching nodes and use chassis grounding or shield termination according to the final enclosure and connector design.
Validate the 1 µA shutdown figure in the intended system because it describes the AutoShutdown state rather than active communication power. During normal data transfer, calculate dissipation from the selected 3.3 V or 5 V supply, loaded driver levels, and enabled receiver count. Confirm that the supply remains within 3.0 V to 5.5 V over tolerance and that startup or wake-up timing meets the host communication protocol.
কমপ্লায়েন্স তথ্য
The exact MAX3243EEAI ordering code and environmental compliance declarations should be confirmed against the current manufacturer product documentation and declaration of compliance.