MAX3386EIPW - 3V RS-232 Transceiver | Texas Instruments
MPN: MAX3386EIPW ⚠ শেষ কিনার সময়MAX3386EIPW সারাংশ
An RS-232 transceiver is an interface IC that converts between digital logic-level signals and the bipolar voltage levels used by RS-232 equipment. In the product hierarchy, it belongs to the transceiver class of interface ICs, where line drivers transmit logic signals onto the cable and line receivers reconstruct valid logic signals from the cable. The MAX3386EIPW therefore connects low-voltage digital systems to external RS-232 ports while providing the voltage translation and electrostatic-discharge protection required at exposed connectors.
The MAX3386E family supports operation from 3V to 5.5V, allowing its logic-side supply to match 3.3V or 5V systems. The separate VL pin improves compatibility with mixed-voltage systems by supplying the receiver and driver interface at the desired logic level. Its 250kbps maximum data rate is suitable for moderate-speed serial links, while three drivers and two receivers support asymmetric full-duplex connections. The 20-pin TSSOP also supports compact surface-mount PCB layouts.
This device does not include the integrated charge-pump capacitors found in some RS-232 transceivers. Its split-supply architecture requires the external supply arrangements specified by the manufacturer datasheet, and the logic-side supply level must be selected to match the connected digital circuitry. This makes the device particularly appropriate when a controlled logic-side voltage is preferred over a single fixed internal supply arrangement.
Typical uses include industrial control equipment, test and measurement instruments, data-acquisition systems, POS terminals, and embedded serial-port interfaces. In an industrial sensor interface, the MAX3386EIPW can translate between a 3.3V controller and a ±12V RS-232 bus while the ±15kV IEC ESD protection helps reduce connector-borne discharge damage. The interface should still be paired with suitable board-level grounding and enclosure practices.
When laying out the PCB, place the device near the protected RS-232 connector and route driver and receiver traces away from sensitive analog or high-speed digital signals. Confirm the logic-side voltage, external capacitor requirements, and input slew behavior against the manufacturer datasheet before release. Validate the assembled interface for the required cable length, ground-reference arrangement, and system ESD level.
This page combines the manufacturer family specifications, package information, lifecycle indication, verified drop-in cross-reference information, and practical interface-design guidance to support component selection and PCB planning.
এর জন্য ড্রপ-ইন বিকল্প MAX3386EIPW — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।
এই সিরিজের ভ্যারিয়েন্ট
একই সিরিজের মডেল যেগুলো drop-in compatible MAX3386EIPW (একই form factor এবং footprint) — পার্থক্য রয়েছে Package, Data Rate, Driver Count, Lifecycle Status, Receiver Count.
TRS3386EIPWR
✅ ড্রপ-ইন📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
MAX3386EIPW বিশেষণ
| Product Type | RS-232 transceiver |
| Driver Count | 3 drivers |
| Receiver Count | 2 receivers |
| ডেটা রেট | 250kbps |
| Supply Voltage Range | 3V to 5.5V |
| Logic-Side Supply | Split VL supply pin |
| ESD Protection | ±15kV IEC ESD protection |
| Protected RIN Inputs | ±15kV human-body-model ESD protection |
| Protected DOUT Outputs | ±15kV human-body-model ESD protection |
| প্যাকেজ | 20-pin TSSOP (PW) |
| Package Width | 4.40mm |
| মাউন্টিং টাইপ | Surface mount |
| লাইফসাইকেল স্ট্যাটাস | Last Time Buy |
MAX3386EIPW 4.40mm পিন কনফিগারেশন গাইড
MAX3386EIPW (4.40mm প্যাকেজ)-এর পিন কনফিগারেশন। পিন নম্বরিং, ফাংশন এবং সংযোগ ডায়াগ্রাম প্রস্তুতকারকের ডেটাশিটে সংজ্ঞায়িত করা আছে। সঠিক ফুটপ্রিন্ট এবং সোল্ডারিং নির্দেশিকার জন্য এটি দেখুন।
এর জন্য বিস্তারিত পিনআউট ডেটা পাওয়া যায়নি MAX3386EIPW.
দেখুন ডেটাশিট সম্পূর্ণ পিন কনফিগারেশনের জন্য।
সাধারণ ব্যবহার
MAX3386EIPW এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Industrial Sensor and Controller Interfaces, Test and Measurement Equipment, Point-of-Sale Terminals, Data Acquisition Systems, Embedded Serial Port Expansion, Communications and Networking Gateways.
Industrial Sensor and Controller Interfaces
The MAX3386EIPW fits industrial controller designs that expose an RS-232 port while operating from a 3.3V or 5V logic rail. Its three drivers and two receivers support a multi-wire full-duplex interface, and the 250kbps rate is sufficient for many sensors, indicators, and configuration links. The split VL connection lets the designer align the interface voltage with the controller logic. The ±15kV IEC ESD protection on exposed RIN and DOUT paths adds useful protection for equipment that may be connected to user-accessible cabling, although the complete product still requires appropriate board grounding and enclosure design.
সুপারিশকৃত
Test and Measurement Equipment
The MAX3386EIPW is useful in bench instruments and field-test equipment that need a compact RS-232 command port. A 250kbps link is appropriate for configuration commands, result transfer, and firmware-related interfaces where throughput beyond a standard RS-232 port is unnecessary. The 20-pin TSSOP allows placement close to the connector, helping keep exposed cable-side traces short. Its split VL supply architecture supports mixed 3.3V and 5V system partitioning, while enhanced IEC ESD protection improves robustness at the connector boundary. Validate the cable length, ground reference, and receiver threshold behavior under the intended operating conditions.
সুপারিশকৃত
Point-of-Sale Terminals
The MAX3386EIPW can support the legacy RS-232 port found on point-of-sale equipment, scales, and receipt peripherals. The three-driver and two-receiver arrangement accommodates the common transmit, receive, and handshake signal mix, while 250kbps is more than adequate for many transaction commands and status messages. Its 3V-to-5.5V operating range allows the interface to coexist with both 3.3V and 5V embedded systems. Placing the TSSOP device near the connector shortens cable-side routing, and the ±15kV IEC ESD rating helps protect the port from charged cable and connector events. Mechanical retention and board-level grounding remain important system protections.
সুপারিশকৃত
Data Acquisition Systems
The MAX3386EIPW is appropriate for data-acquisition equipment that must communicate with a host computer or controller through RS-232. The 250kbps rate supports moderate command traffic and periodic measurement results without requiring a higher-speed differential interface. Its dedicated VL pin gives the designer flexibility when the acquisition controller and transceiver logic domains use different voltage levels. Three drivers and two receivers allow multiple signal lines to be carried on one RS-232 port, which can simplify wiring to legacy equipment. For laboratory and industrial deployments, use the enhanced ESD capability as one layer of protection and validate signal integrity against the selected cable and grounding arrangement.
সুপারিশকৃত
Embedded Serial Port Expansion
The MAX3386EIPW can add an RS-232 port to an embedded controller that otherwise exposes only USB, UART, or proprietary serial interfaces. Its 250kbps maximum rate suits configuration links and low-bandwidth command protocols, while the three-driver and two-receiver arrangement provides practical line coverage. The 20-pin TSSOP is compatible with compact surface-mount assemblies, and the split VL architecture lets the logic side follow the embedded processor voltage. The designer must account for the external supply and capacitance network specified by the family datasheet rather than assuming a fully self-contained charge-pump implementation. This arrangement is useful when compatibility with existing RS-232 peripherals is more important than maximum data throughput.
সুপারিশকৃত
Communications and Networking Gateways
The MAX3386EIPW can serve as a legacy RS-232 leg within gateways, protocol converters, and service equipment that combine older serial interfaces with newer embedded systems. Its 3V-to-5.5V range and split VL pin simplify interface partitioning when the gateway logic uses a different supply from the main transceiver domain. The three transmitters and two receivers map well to typical RS-232 data and control lines, and 250kbps is suitable for configuration and supervisory traffic rather than bulk file transfer. Locate the transceiver near the connector, keep ground and cable routes controlled, and use the manufacturer’s ESD ratings as part of the enclosure and surge-protection strategy.
সুপারিশকৃত
সুপারিশকৃত পণ্যের সারসংক্ষেপ
এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা MAX3386EIPW — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।
নির্বাচন গাইড
বিকল্পের সাথে তুলনা
| পারামিটার | এই পণ্য | TRS3386EIPWR |
|---|---|---|
| Brand | Texas Instruments | Texas Instruments |
| Package | 20-pin TSSOP (PW) | 20-pin TSSOP - same package |
| Product Type | RS-232 transceiver | RS-232 transceiver |
| Supply Voltage Range | 3V to 5.5V | 3V to 5.5V |
| Maximum Data Rate | 250kbps | 250kbps |
| Driver Count | 3 drivers | 3 drivers |
| Receiver Count | 2 receivers | 2 receivers |
মূল পার্থক্যসমূহ
- Documented drop-in compatibility with the TRS3386EIPWR (বনামTRS3386EIPWR)
- Split logic-side supply architecture (বনামTRS3386EIPWR)
- Specified connector-side ESD capability (বনামTRS3386EIPWR)
- Three-driver and two-receiver RS-232 configuration (বনামTRS3386EIPWR)
ডিজাইন নোট
Place the MAX3386EIPW close to the RS-232 connector and keep driver, receiver, and connector traces short. Route the split VL connection and its decoupling directly to the logic-side supply, while following the manufacturer datasheet for every external capacitor connection and value. Keep the exposed cable-side interface away from clocks, precision analog inputs, and sensitive control nets. Confirm that the PCB land pattern uses the 20-pin PW TSSOP dimensions and that the pin-1 orientation matches the package marking.
Do not reuse the charge-pump capacitor network from a MAX3223-family design without checking the MAX3386E datasheet, because the MAX3386EIPW uses a split-supply architecture and does not have the same integrated charge-pump arrangement. Select VL to match the connected logic thresholds and current requirements. Also verify the external network, bypass capacitors, operating temperature grade, and package code before release, particularly because the family is designated last-time-buy and may not be the preferred choice for new designs when an active equivalent is available.
Use the MAX3386EIPW as the connector-side protection element rather than the complete EMC solution. Provide a low-impedance return path between the interface ground and the system reference plane, consider a suitable chassis or signal-ground arrangement, and keep the RS-232 cable away from high-energy switching nodes. The ±15kV IEC ESD rating addresses electrostatic-disense events on the specified pins; it does not eliminate the need for surge protection, cable shielding, or correct enclosure grounding.
Although the rated data rate is 250kbps, interface behavior still depends on the external capacitance network, receiver thresholds, cable length, and ground reference. Use the manufacturer test conditions as the starting point and verify the assembled board with the actual cable and peripheral. Avoid long stubs between the transceiver and connector, and ensure the logic-side receiver sees clean levels at the maximum specified data rate and operating supply.
কমপ্লায়েন্স তথ্য
The MAX3386E is specified with ±15kV IEC ESD protection. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status were not established from the manufacturer information and remain unknown.