最后一次采购通知: MAX3386EIPW 即将停产。最后下单日期: 联系我们. 查看可用的替代料号 →
Texas Instruments

MAX3386EIPW - 3V RS-232 Transceiver | Texas Instruments

料号: MAX3386EIPW ⚠ 最后一次采购
3V to 5.5V Vdss 20-pin TSSOP (PW) Package
最小起订量: 1 |

MAX3386EIPW 概述

Texas Instruments MAX3386EIPW is a 3V-to-5.5V RS-232 line driver and receiver capable of 250kbps operation, packaged in a 20-pin TSSOP. It combines three drivers, two receivers, a split logic-side supply connection, and enhanced IEC 61000-4-2 ESD protection rated to ±15kV on receiver inputs and driver outputs.

An RS-232 transceiver is an interface IC that converts between digital logic-level signals and the bipolar voltage levels used by RS-232 equipment. In the product hierarchy, it belongs to the transceiver class of interface ICs, where line drivers transmit logic signals onto the cable and line receivers reconstruct valid logic signals from the cable. The MAX3386EIPW therefore connects low-voltage digital systems to external RS-232 ports while providing the voltage translation and electrostatic-discharge protection required at exposed connectors.

The MAX3386E family supports operation from 3V to 5.5V, allowing its logic-side supply to match 3.3V or 5V systems. The separate VL pin improves compatibility with mixed-voltage systems by supplying the receiver and driver interface at the desired logic level. Its 250kbps maximum data rate is suitable for moderate-speed serial links, while three drivers and two receivers support asymmetric full-duplex connections. The 20-pin TSSOP also supports compact surface-mount PCB layouts.

This device does not include the integrated charge-pump capacitors found in some RS-232 transceivers. Its split-supply architecture requires the external supply arrangements specified by the manufacturer datasheet, and the logic-side supply level must be selected to match the connected digital circuitry. This makes the device particularly appropriate when a controlled logic-side voltage is preferred over a single fixed internal supply arrangement.

Typical uses include industrial control equipment, test and measurement instruments, data-acquisition systems, POS terminals, and embedded serial-port interfaces. In an industrial sensor interface, the MAX3386EIPW can translate between a 3.3V controller and a ±12V RS-232 bus while the ±15kV IEC ESD protection helps reduce connector-borne discharge damage. The interface should still be paired with suitable board-level grounding and enclosure practices.

When laying out the PCB, place the device near the protected RS-232 connector and route driver and receiver traces away from sensitive analog or high-speed digital signals. Confirm the logic-side voltage, external capacitor requirements, and input slew behavior against the manufacturer datasheet before release. Validate the assembled interface for the required cable length, ground-reference arrangement, and system ESD level.

This page combines the manufacturer family specifications, package information, lifecycle indication, verified drop-in cross-reference information, and practical interface-design guidance to support component selection and PCB planning.

直接替换替代料: MAX3386EIPW ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。

本系列中的变体

可与以下型号直接替换的同系列型号: MAX3386EIPW (相同外形与封装尺寸) ——差异在于 Package, Data Rate, Driver Count, Lifecycle Status, Receiver Count.

Texas Instruments
Package: 20-SOIC (0.295 inch, 7.50 mm width)
Driver Count: 3
Lifecycle Status: Obsolete
对比 MAX3386EIPW →
Analog Devices
Package: 24-TSSOP (4.40 mm)
Data Rate: 250 kbps
对比 MAX3386EIPW →

TRS3386EIPWR

✅ 直接替换
📦 20-pin TSSOP (PW)
Same 3V-to-5.5V rating, three-driver configuration, 250kbps data rate, and TSSOP-20 package; qualification and lifecycle details differ

📋 参考替代料(不在目录中)

MAX3386EIPW 规格参数

Product Type RS-232 transceiver
Driver Count 3 drivers
Receiver Count 2 receivers
数据速率 250kbps
Supply Voltage Range 3V to 5.5V
Logic-Side Supply Split VL supply pin
ESD Protection ±15kV IEC ESD protection
Protected RIN Inputs ±15kV human-body-model ESD protection
Protected DOUT Outputs ±15kV human-body-model ESD protection
封装 20-pin TSSOP (PW)
Package Width 4.40mm
安装类型 Surface mount
生命周期状态 Last Time Buy

MAX3386EIPW 4.40mm 引脚配置指南

MAX3386EIPW(4.40mm 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。

MAX3386EIPW 的 4.40mm 封装引脚图

暂无详细引脚数据: MAX3386EIPW.

请参阅 数据手册 以查看完整引脚配置。

典型应用

MAX3386EIPW 适用于 6 应用s: Industrial Sensor and Controller Interfaces, Test and Measurement Equipment, Point-of-Sale Terminals, Data Acquisition Systems, Embedded Serial Port Expansion, Communications and Networking Gateways.

🏭

Industrial Sensor and Controller Interfaces

The MAX3386EIPW fits industrial controller designs that expose an RS-232 port while operating from a 3.3V or 5V logic rail. Its three drivers and two receivers support a multi-wire full-duplex interface, and the 250kbps rate is sufficient for many sensors, indicators, and configuration links. The split VL connection lets the designer align the interface voltage with the controller logic. The ±15kV IEC ESD protection on exposed RIN and DOUT paths adds useful protection for equipment that may be connected to user-accessible cabling, although the complete product still requires appropriate board grounding and enclosure design.

🔧

Test and Measurement Equipment

The MAX3386EIPW is useful in bench instruments and field-test equipment that need a compact RS-232 command port. A 250kbps link is appropriate for configuration commands, result transfer, and firmware-related interfaces where throughput beyond a standard RS-232 port is unnecessary. The 20-pin TSSOP allows placement close to the connector, helping keep exposed cable-side traces short. Its split VL supply architecture supports mixed 3.3V and 5V system partitioning, while enhanced IEC ESD protection improves robustness at the connector boundary. Validate the cable length, ground reference, and receiver threshold behavior under the intended operating conditions.

🖥️

Point-of-Sale Terminals

The MAX3386EIPW can support the legacy RS-232 port found on point-of-sale equipment, scales, and receipt peripherals. The three-driver and two-receiver arrangement accommodates the common transmit, receive, and handshake signal mix, while 250kbps is more than adequate for many transaction commands and status messages. Its 3V-to-5.5V operating range allows the interface to coexist with both 3.3V and 5V embedded systems. Placing the TSSOP device near the connector shortens cable-side routing, and the ±15kV IEC ESD rating helps protect the port from charged cable and connector events. Mechanical retention and board-level grounding remain important system protections.

📡

Data Acquisition Systems

The MAX3386EIPW is appropriate for data-acquisition equipment that must communicate with a host computer or controller through RS-232. The 250kbps rate supports moderate command traffic and periodic measurement results without requiring a higher-speed differential interface. Its dedicated VL pin gives the designer flexibility when the acquisition controller and transceiver logic domains use different voltage levels. Three drivers and two receivers allow multiple signal lines to be carried on one RS-232 port, which can simplify wiring to legacy equipment. For laboratory and industrial deployments, use the enhanced ESD capability as one layer of protection and validate signal integrity against the selected cable and grounding arrangement.

🧩

Embedded Serial Port Expansion

The MAX3386EIPW can add an RS-232 port to an embedded controller that otherwise exposes only USB, UART, or proprietary serial interfaces. Its 250kbps maximum rate suits configuration links and low-bandwidth command protocols, while the three-driver and two-receiver arrangement provides practical line coverage. The 20-pin TSSOP is compatible with compact surface-mount assemblies, and the split VL architecture lets the logic side follow the embedded processor voltage. The designer must account for the external supply and capacitance network specified by the family datasheet rather than assuming a fully self-contained charge-pump implementation. This arrangement is useful when compatibility with existing RS-232 peripherals is more important than maximum data throughput.

🌐

Communications and Networking Gateways

The MAX3386EIPW can serve as a legacy RS-232 leg within gateways, protocol converters, and service equipment that combine older serial interfaces with newer embedded systems. Its 3V-to-5.5V range and split VL pin simplify interface partitioning when the gateway logic uses a different supply from the main transceiver domain. The three transmitters and two receivers map well to typical RS-232 data and control lines, and 250kbps is suitable for configuration and supervisory traffic rather than bulk file transfer. Locate the transceiver near the connector, keep ground and cable routes controlled, and use the manufacturer’s ESD ratings as part of the enclosure and surge-protection strategy.

推荐产品汇总

MAX3223IPW RS-232 transceiver with integrated charge-pump capacitors for comparison in industrial interface designs 用于: Industrial Sensor and Controller Interfaces, Test and Measurement Equipment, Point-of-Sale Terminals, Data Acquisition Systems, Embedded Serial Port Expansion, Communications and Networking Gateways MAX3386EIPW Texas Instruments 用于: Industrial Sensor and Controller Interfaces, Test and Measurement Equipment, Point-of-Sale Terminals, Data Acquisition Systems, Embedded Serial Port Expansion, Communications and Networking Gateways
What is the MAX3386EIPW?
The MAX3386EIPW is a 3V-to-5.5V, 250kbps RS-232 transceiver with three drivers, two receivers, a split logic-side supply pin, and ±15kV IEC ESD protection. According to the Texas Instruments product page and manufacturer datasheet, it is packaged in a 20-pin TSSOP and intended for compact systems that translate between low-voltage logic and RS-232 line levels. Its split VL arrangement is particularly useful when the connected digital logic operates at a voltage different from the charge-pump side.
What are the key specifications of MAX3386EIPW that engineers should know?
The MAX3386EIPW operates from 3V to 5.5V, supports data rates up to 250kbps, and provides three RS-232 drivers with two receivers in a 20-pin TSSOP package. The Texas Instruments product page identifies ±15kV IEC ESD protection, while the manufacturer datasheet describes enhanced protection on RIN inputs and DOUT outputs. A split VL supply pin permits the logic side to match mixed-voltage systems, and the absence of integrated charge-pump capacitors requires the recommended external network to be included in the PCB design.
Where can I download the MAX3386EIPW datasheet PDF?
The official MAX3386E datasheet and product resources are available from the Texas Instruments MAX3386E product page at https://www.ti.com/product/MAX3386E. This manufacturer page is the preferred starting point for the electrical characteristics, pin descriptions, external-capacitor requirements, and ordering information. The MAX3386EIPW ordering code identifies the industrial-temperature, 20-pin TSSOP configuration, while the family datasheet covers the shared MAX3386E electrical characteristics and application guidance.
Where can I find the MAX3386EIPW pinout?
The MAX3386EIPW pinout is published in the pin-description section of the Texas Instruments MAX3386E manufacturer datasheet. The device uses a 20-pin TSSOP package, designated PW by the ordering information, and its pins are assigned counter-clockwise beginning with pin 1. Use the datasheet pin table when assigning VCC, VL, ground, receiver outputs, driver inputs, and RS-232 line terminals because signal names and no-connect positions must be copied exactly into the schematic and layout.
How does the split VL pin help in a 3.3V system?
The split VL pin allows the logic-side voltage to be selected independently of the main transceiver supply, improving compatibility with mixed-voltage systems. According to the Texas Instruments manufacturer datasheet, the MAX3386E can operate over a 3V-to-5.5V supply range and includes a dedicated VL connection for the logic side. In a 3.3V controller design, VL can be connected to the appropriate 3.3V rail after checking the family datasheet for current, timing, and input-threshold requirements.
What is the difference between MAX3386EIPW and MAX3223IPW?
The MAX3386EIPW uses a split logic-side supply arrangement and does not include the integrated charge-pump capacitors associated with MAX3223IPW. The MAX3386EIPW supports 3V-to-5.5V operation, three drivers, two receivers, 250kbps signaling, and ±15kV IEC ESD protection. A MAX3223IPW circuit should not be assumed to be interchangeable without reviewing its capacitor connections, supply arrangement, and pin functions in both manufacturer datasheets.
Is the MAX3386EIPW suitable for industrial RS-232 equipment?
The MAX3386EIPW is suitable for industrial RS-232 interfaces that require a 3V-to-5.5V supply and moderate-speed operation up to 250kbps. Its ±15kV IEC ESD protection on the RS-232-facing pins adds connector protection, while the three-driver and two-receiver arrangement supports practical full-duplex equipment wiring. The manufacturer datasheet should be checked for the exact temperature grade and electrical limits, and the completed interface must still be validated against the required industrial ESD and ground-reference conditions.
What can replace the MAX3386EIPW?
The TRS3386EIPWR is a documented drop-in candidate for the MAX3386EIPW because the cross-reference identifies the same TSSOP-20 terminal arrangement and equivalent RS-232 transceiver characteristics. It is a 3V-to-5.5V RS-232 device with three drivers and a maximum data rate of 250kbps, matching the principal electrical ratings of the target. Engineers should still verify pin functions, external capacitor requirements, ESD ratings, lifecycle status, and qualification requirements before approving a production substitution.
Is the TRS3386EIPWR the same as the MAX3386EIPW?
The TRS3386EIPWR is not the same manufacturer part number, but its published cross-reference describes it as a complete, terminal- and package-consistent replacement for the MAX3386EIPW. Both are identified as 3V-to-5.5V RS-232 transceivers in TSSOP-20 packages, with three drivers and a 250kbps maximum rate. They should still be treated as different purchasable devices until lead time, lifecycle, environmental qualification, and exact pin-level compatibility have been reviewed.
When should I choose MAX3386EIPW over TRS3386EIPWR?
Choose the MAX3386EIPW when the system needs the Texas Instruments MAX3386E family, its documented split VL logic-side supply arrangement, and its stated ±15kV IEC ESD protection. Choose the TRS3386EIPWR when its compatible TSSOP-20 implementation offers a practical procurement path and its separate qualification record better fits the product program. Both support 3V-to-5.5V operation, three drivers, two receivers, and 250kbps signaling, so supply-chain and qualification requirements often become the deciding factors.
Where can I buy MAX3386EIPW online?
Use the Request a Quote form on this page to request current MAX3386EIPW availability, lead time, and an order quote. The requested device is the Texas Instruments 20-pin TSSOP configuration and should be identified by its complete MPN to avoid confusing it with other MAX3386E package or temperature options. Because the manufacturer lists the family as last-time-buy, buyers should request lifecycle confirmation and delivery information before committing a new production release.
What is the price of MAX3386EIPW?
Current MAX3386EIPW commercial terms should be requested through the Request a Quote form on this page. The part is a last-time-buy device, so quoted availability, quantity breaks, lead time, and any remaining authorized-channel inventory can change as the supply is depleted. State the required order quantity and delivery schedule in the request so the commercial response reflects the actual procurement need rather than a generic listing value.
What is the lead time for MAX3386EIPW?
The current lead time for MAX3386EIPW should be confirmed through the Request a Quote form on this page. Texas Instruments identifies the MAX3386E family as last-time-buy, making lot availability and scheduled depletion important considerations for production planning. Ask the supplier to confirm the quantity available, shipment date, traceability requirements, and whether any order allocation remains. Requesting a quote with the required delivery date provides the clearest basis for a sourcing decision.
Is MAX3386EIPW in stock?
MAX3386EIPW inventory should be checked through the Request a Quote form on this page. The manufacturer product information identifies the family as last-time-buy, while distributor listings may contain residual stock from different channels. Provide your required quantity, target date, and acceptable lot or traceability conditions with the request. This avoids treating a distributor’s historical inventory count as a guaranteed allocation and supports a clear production plan.
Does MAX3386EIPW need external charge-pump capacitors?
The MAX3386EIPW does not use the same integrated charge-pump arrangement as every competing RS-232 transceiver, so the required external network must be taken directly from the Texas Instruments manufacturer datasheet. Its split-supply architecture includes a dedicated VL pin for the logic side. Before layout, confirm the required VCC and VL connections, capacitance values, capacitor tolerances, and charge-pump connections in the current datasheet rather than reusing the external network from a MAX3223-family design.

工程参考数据: MAX3386EIPW ——对比、设计指导和合规信息。

选型指南

Choose the MAX3386EIPW when the design requires the MAX3386E family’s split VL logic-side supply, ±15kV IEC ESD protection, and a 20-pin TSSOP footprint. It is particularly appropriate for 3.3V or 5V industrial systems that need three RS-232 drivers, two receivers, and communication up to 250kbps. The TRS3386EIPWR is the documented drop-in choice when its supply status, qualification, and manufacturer records better fit the program. Both are listed with the same package, supply range, driver count, receiver count, and maximum data rate. Because the MAX3386E family is last-time-buy, use it primarily for compatible existing designs or scheduled migration programs, and prefer a current active product for new platforms whenever system requirements permit. Confirm the exact external capacitor network, pin functions, temperature grade, and production availability before approval.

与替代料对比

参数 本产品 TRS3386EIPWR
Brand Texas Instruments Texas Instruments
Package 20-pin TSSOP (PW) 20-pin TSSOP - same package
Product Type RS-232 transceiver RS-232 transceiver
Supply Voltage Range 3V to 5.5V 3V to 5.5V
Maximum Data Rate 250kbps 250kbps
Driver Count 3 drivers 3 drivers
Receiver Count 2 receivers 2 receivers

关键差异点

  • Documented drop-in compatibility with the TRS3386EIPWR (对比 TRS3386EIPWR)
  • Split logic-side supply architecture (对比 TRS3386EIPWR)
  • Specified connector-side ESD capability (对比 TRS3386EIPWR)
  • Three-driver and two-receiver RS-232 configuration (对比 TRS3386EIPWR)

设计说明

Place the MAX3386EIPW close to the RS-232 connector and keep driver, receiver, and connector traces short. Route the split VL connection and its decoupling directly to the logic-side supply, while following the manufacturer datasheet for every external capacitor connection and value. Keep the exposed cable-side interface away from clocks, precision analog inputs, and sensitive control nets. Confirm that the PCB land pattern uses the 20-pin PW TSSOP dimensions and that the pin-1 orientation matches the package marking.

Do not reuse the charge-pump capacitor network from a MAX3223-family design without checking the MAX3386E datasheet, because the MAX3386EIPW uses a split-supply architecture and does not have the same integrated charge-pump arrangement. Select VL to match the connected logic thresholds and current requirements. Also verify the external network, bypass capacitors, operating temperature grade, and package code before release, particularly because the family is designated last-time-buy and may not be the preferred choice for new designs when an active equivalent is available.

Use the MAX3386EIPW as the connector-side protection element rather than the complete EMC solution. Provide a low-impedance return path between the interface ground and the system reference plane, consider a suitable chassis or signal-ground arrangement, and keep the RS-232 cable away from high-energy switching nodes. The ±15kV IEC ESD rating addresses electrostatic-disense events on the specified pins; it does not eliminate the need for surge protection, cable shielding, or correct enclosure grounding.

Although the rated data rate is 250kbps, interface behavior still depends on the external capacitance network, receiver thresholds, cable length, and ground reference. Use the manufacturer test conditions as the starting point and verify the assembled board with the actual cable and peripheral. Avoid long stubs between the transceiver and connector, and ensure the logic-side receiver sees clean levels at the maximum specified data rate and operating supply.

合规信息

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
无铅
Unknown
无卤
Unknown
冲突矿物
Unknown

The MAX3386E is specified with ±15kV IEC ESD protection. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status were not established from the manufacturer information and remain unknown.

数据核验日期: 2026-11-09 ——数据由 XAIPART 元器件工程团队核验和整理

相关搜索

MAX3386EIPW datasheet MAX3386EIPW pinout MAX3386EIPW datasheet pdf MAX3386EIPW replacement MAX3386EIPW equivalent MAX3386EIPW price MAX3386EIPW stock MAX3386EIPW schematic MAX3386EIPW vs TRS3386EIPWR Texas Instruments MAX3386EIPW MAX3386EIPW 20-pin TSSOP MAX3386EIPW 250kbps RS-232 MAX3386EIPW industrial interface MAX3386EIPW drop-in replacement MAX3386EIPW footprint

相关元器件 & 术语

Texas Instruments MAX3386EIPW MAX3386E TRS3386EIPWR MAX3223IPW RS-232 RS-232 transceiver line driver line receiver interface IC semiconductor split logic-side supply VL pin 250kbps data rate 3V to 5.5V supply IEC ESD protection ±15kV ESD 20-pin TSSOP PW package surface mount industrial control equipment data acquisition test and measurement mixed-voltage systems
快速报价
填写完整信息——我们的销售团队将在 24 小时内回复
料号 制造商 封装 QTY 目标价 小计
✓
报价已提交!

我们将在 24 小时内回复您的邮件

1
询价已提交
2
已收到报价
3
已下单
4
支付
5
已发货
6
已送达
查看询价详情