MAX339CSE+ - Dual 4:1 Low-Leakage Analog Multiplexer | Analog Devices
MPN: MAX339CSE+ ✓ সক্রিয়MAX339CSE+ সারাংশ
An analog multiplexer is a semiconductor switching network that connects one of several input terminals to a shared output. The MAX339CSE+ belongs to the analog switch and multiplexer hierarchy, where low-leakage CMOS construction is valuable for high-impedance measurement circuits. Each half of the device uses two binary address inputs to select one of four channels, while enable inputs control whether the selected path is connected.
Key electrical characteristics include a maximum on-resistance of 650 ohms, a single-supply operating range of 4.5 V to 30 V, and dual-supply operation from ±4.5 V to ±20 V. Address and enable logic inputs are TTL compatible from 0.8 V to 2.4 V across the specified temperature and supply ranges. These features support both legacy positive-supply systems and higher-voltage industrial measurement equipment.
The MAX339CSE+ is fabricated using Maxim's 44 V silicon-gate process, providing the voltage headroom needed for the stated 30 V single-supply or ±20 V dual-supply operation. Its low-leakage behavior is particularly useful when source impedance is high and leakage current could otherwise create measurement offsets. The manufacturer also identifies the MAX339 as a pin-compatible upgrade for the industry-standard DG508A and DG509A.
Typical uses include battery and bench instrumentation, process-control signal routing, automated test equipment, data acquisition, multiplexed sensor interfaces, and general-purpose analog signal selection. The dual 4-channel organization allows two independent analog paths on one device, reducing component count when the system does not require a single 8:1 configuration.
Designers should account for off leakage, switch resistance, charge injection, and logic levels when defining the input impedance and settling time. Use the manufacturer pin-description table to assign PCB tracks and confirm that the selected connector, protection network, and source impedance preserve the required measurement accuracy. The 16-pin NSOIC footprint also requires conventional surface-mount assembly and adequate spacing for routing both analog and digital control signals.
This page combines manufacturer specifications, package information, sourcing guidance, drop-in alternatives, and practical circuit-planning notes to support component selection, PCB implementation, and replacement decisions for the MAX339CSE+.
এর জন্য ড্রপ-ইন বিকল্প MAX339CSE+ — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।
এই সিরিজের ভ্যারিয়েন্ট
একই সিরিজের মডেল যেগুলো drop-in compatible MAX339CSE+ (একই form factor এবং footprint) — পার্থক্য রয়েছে Multiplexer Configuration, Package.
MAX339ESE+
✅ ড্রপ-ইন📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
MAX339CSE
✅ ড্রপ-ইন📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
MAX339CSE+ বিশেষণ
| Multiplexer Configuration | Dual 4:1 |
| Total Channels | 8 |
| Architecture | CMOS analog multiplexer |
| On-Resistance | 650 ohms maximum |
| Single-Supply Voltage Range | 4.5 V to 30 V |
| Dual-Supply Voltage Range | ±4.5 V to ±20 V |
| Control Input Compatibility | TTL compatible |
| Control Input Logic Range | 0.8 V to 2.4 V |
| Address Inputs per Multiplexer | 2 binary inputs |
| Enable Inputs | Active-low control inputs |
| প্যাকেজ | 16-pin NSOIC |
| মাউন্টিং টাইপ | Surface mount |
| Process Technology | 44 V silicon-gate CMOS process |
| Operating Mode | Multiplexer or demultiplexer |
MAX339CSE+ 16-pin nsoic পিন কনফিগারেশন গাইড
MAX339CSE+ (16-pin nsoic প্যাকেজ)-এর পিন কনফিগারেশন। পিন নম্বরিং, ফাংশন এবং সংযোগ ডায়াগ্রাম প্রস্তুতকারকের ডেটাশিটে সংজ্ঞায়িত করা আছে। সঠিক ফুটপ্রিন্ট এবং সোল্ডারিং নির্দেশিকার জন্য এটি দেখুন।
এর জন্য বিস্তারিত পিনআউট ডেটা পাওয়া যায়নি MAX339CSE+.
দেখুন ডেটাশিট সম্পূর্ণ পিন কনফিগারেশনের জন্য।
সাধারণ ব্যবহার
MAX339CSE+ এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Automated Test Equipment Signal Routing, Process-Control Sensor Multiplexing, Battery-Powered Data Acquisition, Multiplexed Sensor Interface, General-Purpose Analog Signal Selection, Dual Independent Analog Routing.
Automated Test Equipment Signal Routing
The MAX339CSE+ fits automated test equipment that must route several low-level analog sources to a common measurement channel. Two independent 4:1 sections provide eight paths in total, while the maximum on-resistance of 650 ohms supports use with relatively low-impedance sources. Its 4.5 V to 30 V single-supply range permits operation from conventional 5 V laboratory rails or higher-voltage industrial test systems. TTL-compatible address and enable controls simplify integration with legacy test-controller logic. Engineers should include the switch resistance in the measurement path and verify settling time, leakage, and charge injection against the required test accuracy.
সুপারিশকৃত
Process-Control Sensor Multiplexing
The MAX339CSE+ can route multiple plant sensors into a controller or data-acquisition front end while preserving a compact interface footprint. Its low-leakage CMOS construction is valuable when sensors have high source impedance and leakage current could create an unacceptable measurement offset. The dual 4:1 organization allows two independently controlled measurement groups on one IC. A 4.5 V minimum single supply suits 5 V process electronics, while the 30 V maximum adds flexibility for higher-voltage instrumentation. Design the input network to account for 650 ohms maximum on-resistance and ensure that transient protection does not compromise leakage-sensitive accuracy.
সুপারিশকৃত
Battery-Powered Data Acquisition
The MAX339CSE+ is appropriate for compact battery-powered data-acquisition systems that must select among several analog sensors using limited logic resources. Each 4:1 section needs only two address inputs, allowing a microcontroller to choose a channel while an enable input controls connection timing. Operation from a single 4.5 V to 30 V supply supports both low-voltage portable systems and higher-voltage industrial installations. The low-leakage characteristic helps preserve accuracy with resistive sensors, although total system error must include sensor impedance, mux on-resistance, input bias current, and leakage. Power-budget calculations should also include the logic levels and quiescent behavior of the selected operating mode.
সুপারিশকৃত
Multiplexed Sensor Interface
The MAX339CSE+ can connect resistive, thermocouple, or other slowly varying analog sensors to a shared signal-conditioning channel. Its two 4:1 sections permit separate positive and reference routing schemes, while TTL-compatible controls allow simple interfacing with a digital controller. The 4.5 V minimum supply supports 5 V systems, and the 30 V ceiling is useful for industrial sensors with wider common-mode requirements when the circuit is configured appropriately. Because the device has a 650-ohm maximum on-resistance, use it where source impedance permits that resistance to remain small compared with the sensor impedance. Verify cold-junction, leakage, and settling requirements in the final analog path.
সুপারিশকৃত
General-Purpose Analog Signal Selection
The MAX339CSE+ provides a straightforward way to route two banks of four analog signals to common outputs in laboratory, educational, and control equipment. The device can also be used as a demultiplexer when a selected signal must be distributed among multiple outputs. Its broad 4.5 V to 30 V supply range makes it suitable for legacy positive-supply systems, while the 44 V silicon-gate process supports the specified operating voltages. TTL-compatible address and enable inputs reduce controller-interface complexity. For switching waveforms or precision settling tests, evaluate transition behavior and charge injection from the manufacturer data sheet rather than treating the mux as an ideal zero-resistance switch.
সুপারিশকৃত
Dual Independent Analog Routing
The MAX339CSE+ is useful when a system needs two separate 4:1 paths rather than one 8:1 selector, such as paired reference and measurement routing or coordinated control of two signal groups. Independent address selection prevents one bank from disturbing the other, while the shared package reduces board area compared with two single-channel selector assemblies. The 16-pin NSOIC format supports conventional surface-mount routing and keeps control signals separate from analog tracks. The maximum 650-ohm on-resistance remains the principal accuracy consideration, especially with high-impedance sources. Use short analog traces, a quiet ground reference, and deliberate return paths to avoid adding pickup to the low-leakage measurement architecture.
সুপারিশকৃত
সুপারিশকৃত পণ্যের সারসংক্ষেপ
এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা MAX339CSE+ — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।
নির্বাচন গাইড
বিকল্পের সাথে তুলনা
| পারামিটার | এই পণ্য | MAX339ESE+ | MAX339CSE |
|---|---|---|---|
| Package | 16-pin NSOIC | 16-pin NSOIC | 16-pin SOIC |
| Brand | Analog Devices | Analog Devices | Analog Devices |
| Multiplexer Configuration | Dual 4:1 | Dual 4:1 | Dual 4:1 |
| Total Channels | 8 | 8 | 8 |
| Maximum On-Resistance | 650 ohms | 650 ohms | 400 ohms |
| Architecture | Low-leakage CMOS analog multiplexer | Low-leakage CMOS analog multiplexer | CMOS analog multiplexer |
মূল পার্থক্যসমূহ
- Supports a broad positive-supply operating range (বনামMAX339ESE+)
- Provides two independent 4:1 switch sections (বনামMAX339CSE)
- Uses a 44 V silicon-gate process (বনামMAX339ESE+)
ডিজাইন নোট
Treat the selected channel as a resistive network rather than an ideal conductor. The MAX339CSE+ has a maximum on-resistance of 650 ohms, so include it when calculating divider attenuation, input loading, amplifier offset, and settling time. For a high-impedance source, the 650-ohm contribution may be small compared with the sensor impedance, but it can still dominate a precision measurement. Add the leakage current of the selected amplifier and protection devices to the total error budget.
Keep analog input and common-output traces short and route address and enable controls away from sensitive analog paths. The common output and supply return are critical to low-leakage performance; avoid long copper traces, test pads, and connectors that can add surface leakage. Place any input protection network close to the device while accounting for its leakage and capacitance, and connect the supply ground with a low-impedance path to the package ground pins.
Do not infer every pin function from the generic 16-pin SOIC outline. Use the MAX338/MAX339 manufacturer pin-description table to assign address inputs, enable inputs, common outputs, channel inputs, positive supply, and negative supply. Also distinguish the MAX339CSE+ from the MAX339ESE+ temperature grade and verify leakage, switching-time, and absolute-maximum ratings before approving either part as a substitute.
কমপ্লায়েন্স তথ্য
No explicit RoHS, REACH, halogen-free, lead-free, conflict-minerals, or automotive-qualification statement appears in the product information used for this record. AEC-Q100 is not applicable to the documented general-purpose MAX339CSE+ ordering information.