Analog Devices

MAX339CSE+ - Dual 4:1 Low-Leakage Analog Multiplexer | Analog Devices

部品番号: MAX339CSE+ ✓ 生産中
4.5 V to 30 V Vdss 650 ohms maximum Rds(on) 16-pin NSOIC Package
MOQ: 1 |

MAX339CSE+ 概要

Analog Devices MAX339CSE+ is a low-leakage CMOS analog multiplexer containing two independent 4:1 switches, with eight channels in total when configured as a dual 4-channel mux. It supports a single supply of 4.5 V to 30 V or dual supplies of ±4.5 V to ±20 V and is packaged in a 16-pin NSOIC. The device can also operate as a demultiplexer, making it suitable for routing instrumentation, measurement, control, and low-leakage analog signals.

An analog multiplexer is a semiconductor switching network that connects one of several input terminals to a shared output. The MAX339CSE+ belongs to the analog switch and multiplexer hierarchy, where low-leakage CMOS construction is valuable for high-impedance measurement circuits. Each half of the device uses two binary address inputs to select one of four channels, while enable inputs control whether the selected path is connected.

Key electrical characteristics include a maximum on-resistance of 650 ohms, a single-supply operating range of 4.5 V to 30 V, and dual-supply operation from ±4.5 V to ±20 V. Address and enable logic inputs are TTL compatible from 0.8 V to 2.4 V across the specified temperature and supply ranges. These features support both legacy positive-supply systems and higher-voltage industrial measurement equipment.

The MAX339CSE+ is fabricated using Maxim's 44 V silicon-gate process, providing the voltage headroom needed for the stated 30 V single-supply or ±20 V dual-supply operation. Its low-leakage behavior is particularly useful when source impedance is high and leakage current could otherwise create measurement offsets. The manufacturer also identifies the MAX339 as a pin-compatible upgrade for the industry-standard DG508A and DG509A.

Typical uses include battery and bench instrumentation, process-control signal routing, automated test equipment, data acquisition, multiplexed sensor interfaces, and general-purpose analog signal selection. The dual 4-channel organization allows two independent analog paths on one device, reducing component count when the system does not require a single 8:1 configuration.

Designers should account for off leakage, switch resistance, charge injection, and logic levels when defining the input impedance and settling time. Use the manufacturer pin-description table to assign PCB tracks and confirm that the selected connector, protection network, and source impedance preserve the required measurement accuracy. The 16-pin NSOIC footprint also requires conventional surface-mount assembly and adequate spacing for routing both analog and digital control signals.

This page combines manufacturer specifications, package information, sourcing guidance, drop-in alternatives, and practical circuit-planning notes to support component selection, PCB implementation, and replacement decisions for the MAX339CSE+.

ドロップイン代替品: MAX339CSE+ — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。

このシリーズのバリエーション

同一シリーズでドロップイン互換のモデル: MAX339CSE+ (同一形状・フットプリント) — 相違点: Multiplexer Configuration, Package.

Analog Devices
Multiplexer Configuration: 8:1
Package: 16-pin narrow SOIC
比較対象 MAX339CSE+ →

MAX339ESE+

✅ ドロップイン
📦 16-pin NSOIC
Same dual 4:1 architecture, 16-pin NSOIC footprint, and 4.5 V to 30 V supply range; temperature grade and detailed leakage limits require confirmation

📋 参考代替品(カタログ未掲載)

MAX339CSE

✅ ドロップイン
📦 16-pin SOIC
Same MAX339 dual 4:1 family and 16-pin SOIC format; the listed 400-ohm figure differs from the 650-ohm MAX339CSE+ maximum by 38.5%

📋 参考代替品(カタログ未掲載)

MAX339CSE+ 仕様

Multiplexer Configuration Dual 4:1
Total Channels 8
Architecture CMOS analog multiplexer
On-Resistance 650 ohms maximum
Single-Supply Voltage Range 4.5 V to 30 V
Dual-Supply Voltage Range ±4.5 V to ±20 V
Control Input Compatibility TTL compatible
Control Input Logic Range 0.8 V to 2.4 V
Address Inputs per Multiplexer 2 binary inputs
Enable Inputs Active-low control inputs
パッケージ 16-pin NSOIC
実装タイプ Surface mount
Process Technology 44 V silicon-gate CMOS process
Operating Mode Multiplexer or demultiplexer

MAX339CSE+ 16-pin nsoic ピン配置ガイド

MAX339CSE+ (16-pin nsoic パッケージ) のピン配置。 ピン番号、機能、接続図はメーカーのデータシートで定義されています。正確なフットプリントとはんだ付けのガイドラインについては、データシートを参照してください。

MAX339CSE+ の 16-pin nsoic パッケージピン配置図

詳細なピン配置データはありません: MAX339CSE+.

詳細は データシート をご参照ください。

主な用途

MAX339CSE+ の用途: 6 件s: Automated Test Equipment Signal Routing, Process-Control Sensor Multiplexing, Battery-Powered Data Acquisition, Multiplexed Sensor Interface, General-Purpose Analog Signal Selection, Dual Independent Analog Routing.

⚡

Automated Test Equipment Signal Routing

The MAX339CSE+ fits automated test equipment that must route several low-level analog sources to a common measurement channel. Two independent 4:1 sections provide eight paths in total, while the maximum on-resistance of 650 ohms supports use with relatively low-impedance sources. Its 4.5 V to 30 V single-supply range permits operation from conventional 5 V laboratory rails or higher-voltage industrial test systems. TTL-compatible address and enable controls simplify integration with legacy test-controller logic. Engineers should include the switch resistance in the measurement path and verify settling time, leakage, and charge injection against the required test accuracy.

🏭

Process-Control Sensor Multiplexing

The MAX339CSE+ can route multiple plant sensors into a controller or data-acquisition front end while preserving a compact interface footprint. Its low-leakage CMOS construction is valuable when sensors have high source impedance and leakage current could create an unacceptable measurement offset. The dual 4:1 organization allows two independently controlled measurement groups on one IC. A 4.5 V minimum single supply suits 5 V process electronics, while the 30 V maximum adds flexibility for higher-voltage instrumentation. Design the input network to account for 650 ohms maximum on-resistance and ensure that transient protection does not compromise leakage-sensitive accuracy.

🔋

Battery-Powered Data Acquisition

The MAX339CSE+ is appropriate for compact battery-powered data-acquisition systems that must select among several analog sensors using limited logic resources. Each 4:1 section needs only two address inputs, allowing a microcontroller to choose a channel while an enable input controls connection timing. Operation from a single 4.5 V to 30 V supply supports both low-voltage portable systems and higher-voltage industrial installations. The low-leakage characteristic helps preserve accuracy with resistive sensors, although total system error must include sensor impedance, mux on-resistance, input bias current, and leakage. Power-budget calculations should also include the logic levels and quiescent behavior of the selected operating mode.

📡

Multiplexed Sensor Interface

The MAX339CSE+ can connect resistive, thermocouple, or other slowly varying analog sensors to a shared signal-conditioning channel. Its two 4:1 sections permit separate positive and reference routing schemes, while TTL-compatible controls allow simple interfacing with a digital controller. The 4.5 V minimum supply supports 5 V systems, and the 30 V ceiling is useful for industrial sensors with wider common-mode requirements when the circuit is configured appropriately. Because the device has a 650-ohm maximum on-resistance, use it where source impedance permits that resistance to remain small compared with the sensor impedance. Verify cold-junction, leakage, and settling requirements in the final analog path.

🔧

General-Purpose Analog Signal Selection

The MAX339CSE+ provides a straightforward way to route two banks of four analog signals to common outputs in laboratory, educational, and control equipment. The device can also be used as a demultiplexer when a selected signal must be distributed among multiple outputs. Its broad 4.5 V to 30 V supply range makes it suitable for legacy positive-supply systems, while the 44 V silicon-gate process supports the specified operating voltages. TTL-compatible address and enable inputs reduce controller-interface complexity. For switching waveforms or precision settling tests, evaluate transition behavior and charge injection from the manufacturer data sheet rather than treating the mux as an ideal zero-resistance switch.

🖥️

Dual Independent Analog Routing

The MAX339CSE+ is useful when a system needs two separate 4:1 paths rather than one 8:1 selector, such as paired reference and measurement routing or coordinated control of two signal groups. Independent address selection prevents one bank from disturbing the other, while the shared package reduces board area compared with two single-channel selector assemblies. The 16-pin NSOIC format supports conventional surface-mount routing and keeps control signals separate from analog tracks. The maximum 650-ohm on-resistance remains the principal accuracy consideration, especially with high-impedance sources. Use short analog traces, a quiet ground reference, and deliberate return paths to avoid adding pickup to the low-leakage measurement architecture.

What is the MAX339CSE+ and what does it do?
The MAX339CSE+ is a low-leakage CMOS analog multiplexer with two independent 4:1 switch sections, providing eight channels in total. Each section connects one of four inputs to a common output and can also operate as a demultiplexer. According to the Analog Devices MAX338/MAX339 datasheet, the device supports single supplies from 4.5 V to 30 V and dual supplies from ±4.5 V to ±20 V.
What is the on-resistance of the MAX339CSE+?
The MAX339CSE+ has a maximum on-resistance of 650 ohms. This figure comes from the Analog Devices product information for the MAX339 family and is consistent with the 16-pin NSOIC version identified in the MAX339CSE+ listing. On-resistance contributes directly to signal loss and should be included when calculating source impedance, insertion error, and settling behavior in a high-impedance measurement path.
What supply voltages are supported by the MAX339CSE+?
The MAX339CSE+ operates from a single 4.5 V to 30 V supply or from dual supplies of ±4.5 V to ±20 V. The Analog Devices MAX338/MAX339 datasheet specifies these ranges for the family. The selected supply arrangement determines signal-level headroom, while the address and enable inputs remain TTL compatible over the stated operating conditions.
Where can I download the MAX339CSE+ datasheet PDF?
The official MAX339CSE+ datasheet PDF is available from Analog Devices at the MAX338-MAX339 data-sheet URL listed on this page. The document describes the dual 4-channel low-leakage architecture, 4.5 V to 30 V single-supply range, dual-supply range, TTL-compatible controls, package information, and the electrical characteristics needed for circuit design.
Where can I find the MAX339CSE+ pinout?
The MAX339CSE+ pin assignment is documented in the Analog Devices MAX338/MAX339 datasheet, which is linked in the datasheet field on this page. The device is available in a 16-pin NSOIC package. Use the manufacturer pin-description table when laying out address inputs, enable inputs, analog channels, common outputs, and supply connections rather than relying on generic package drawings.
Can the MAX339CSE+ be used as a demultiplexer?
Yes, the MAX339CSE+ can operate as either a multiplexer or a demultiplexer. The Analog Devices data sheet describes the MAX338/MAX339 as monolithic CMOS analog multiplexers whose 4-channel sections route signals under address and enable control. In demultiplexer operation, the common path distributes a selected input to one of four outputs, subject to the same supply, leakage, and switching limitations.
Is the MAX339CSE+ TTL compatible?
The MAX339CSE+ address and enable inputs are TTL compatible over the full specified temperature range and the stated ±4.5 V to ±18 V supply range. According to the MAX338/MAX339 datasheet, the compatible control-input voltage is 0.8 V to 2.4 V. This allows direct interfacing with suitable TTL and CMOS control logic while preserving the mux's wider analog voltage range.
Where can I buy MAX339CSE+ and check current lead time?
Use the Request a Quote form on this page to request MAX339CSE+ availability, current lead time, and order quantities. The part is an Analog Devices 16-pin NSOIC analog multiplexer, and current sourcing terms can change by region and order volume. Submit the required quantity and target date with the request so procurement can confirm the applicable schedule.
What is the price of the MAX339CSE+?
Use the Request a Quote form on this page for the current MAX339CSE+ price and quantity schedule. The component is identified by the exact Analog Devices orderable MPN MAX339CSE+ in a 16-pin NSOIC package. Current commercial terms are handled through the quote workflow so that the response reflects quantity, date, and confirmation requirements.
Is MAX339CSE+ currently in stock?
Current MAX339CSE+ inventory status should be confirmed through the Request a Quote form on this page. The manufacturer product page lists the MAX339 in production, while channel inventory can vary by package, quantity, and date. Provide the required quantity and delivery target in the request to obtain a current availability response.
What can replace the MAX339CSE+?
The MAX339ESE+ is the closest documented same-package replacement candidate for the MAX339CSE+. Both are described as dual 4-channel, low-leakage CMOS analog multiplexers in a 16-pin NSOIC package and support the same 4.5 V to 30 V single-supply range. Confirm the exact pin functions, temperature grade, leakage, and electrical limits in the manufacturer data sheet before releasing a substitution.
MAX339CSE+ vs MAX339ESE+ - which is better for a replacement?
The MAX339ESE+ is the stronger candidate when a same-package replacement is required because it is described as a dual 4-channel low-leakage CMOS mux in a 16-pin NSOIC package with the same 4.5 V to 30 V supply range. The MAX339CSE+ and MAX339ESE+ temperature grades should still be compared for the target application, along with leakage and switching limits in the manufacturer documentation.
When should I choose the MAX339CSE+ instead of another 4-channel mux?
Choose the MAX339CSE+ when the design needs two independent 4:1 sections, low-leakage CMOS behavior, TTL-compatible control, and a broad single-supply range of 4.5 V to 30 V. It is especially suitable for higher-impedance instrumentation where leakage offsets matter. If lower voltage, lower on-resistance, automotive qualification, or a different logic family is required, compare those requirements before finalizing the selection.
Is the MAX339CSE+ suitable for high-impedance sensor measurement?
The MAX339CSE+ is suitable for high-impedance sensor routing when its low-leakage characteristics and input impedance are compatible with the measurement error budget. Its maximum on-resistance is 650 ohms, so source impedance must remain low enough that the switch does not dominate accuracy or settling time. The manufacturer data sheet should be used to confirm leakage, charge injection, and off-state behavior.
What are the key specifications of MAX339CSE+ that engineers should know?
The MAX339CSE+ combines two independent 4:1 CMOS analog switch sections in a 16-pin NSOIC package. According to Analog Devices, it supports 4.5 V to 30 V single-supply operation, ±4.5 V to ±20 V dual-supply operation, up to 650 ohms on-resistance, and TTL-compatible controls. It can function as a multiplexer or demultiplexer and uses a 44 V silicon-gate process.

エンジニアリング参考データ: MAX339CSE+ — 比較、設計ガイダンス、コンプライアンス情報。

選定ガイド

Choose the MAX339CSE+ when the design requires two independent 4:1 analog switch sections, low-leakage CMOS behavior, TTL-compatible address and enable controls, and operation from a 4.5 V to 30 V single supply. It is well suited to high-impedance instrumentation, process-control measurement, automated test systems, and data-acquisition equipment where channel count and leakage are more important than minimum on-resistance. The MAX339ESE+ is the closest documented NSOIC replacement candidate, with the same dual 4:1 configuration and voltage range, but temperature grade and detailed electrical limits should be checked before substitution. The MAX339CSE offers a related 16-pin SOIC option and is listed with 400-ohm on-resistance, 38.5% below the 650-ohm MAX339CSE+ maximum. Choose that variant only after checking whether its lower on-resistance, temperature grade, and leakage characteristics better match the application. For signals requiring less than 400 ohms, verify whether the available family variants can meet the required settling time and insertion loss.

代替品との比較

パラメータ この製品 MAX339ESE+ MAX339CSE
Package 16-pin NSOIC 16-pin NSOIC 16-pin SOIC
Brand Analog Devices Analog Devices Analog Devices
Multiplexer Configuration Dual 4:1 Dual 4:1 Dual 4:1
Total Channels 8 8 8
Maximum On-Resistance 650 ohms 650 ohms 400 ohms
Architecture Low-leakage CMOS analog multiplexer Low-leakage CMOS analog multiplexer CMOS analog multiplexer

主な差別化要因

  • Supports a broad positive-supply operating range (vs MAX339ESE+)
  • Provides two independent 4:1 switch sections (vs MAX339CSE)
  • Uses a 44 V silicon-gate process (vs MAX339ESE+)

設計ノート

Treat the selected channel as a resistive network rather than an ideal conductor. The MAX339CSE+ has a maximum on-resistance of 650 ohms, so include it when calculating divider attenuation, input loading, amplifier offset, and settling time. For a high-impedance source, the 650-ohm contribution may be small compared with the sensor impedance, but it can still dominate a precision measurement. Add the leakage current of the selected amplifier and protection devices to the total error budget.

Keep analog input and common-output traces short and route address and enable controls away from sensitive analog paths. The common output and supply return are critical to low-leakage performance; avoid long copper traces, test pads, and connectors that can add surface leakage. Place any input protection network close to the device while accounting for its leakage and capacitance, and connect the supply ground with a low-impedance path to the package ground pins.

Do not infer every pin function from the generic 16-pin SOIC outline. Use the MAX338/MAX339 manufacturer pin-description table to assign address inputs, enable inputs, common outputs, channel inputs, positive supply, and negative supply. Also distinguish the MAX339CSE+ from the MAX339ESE+ temperature grade and verify leakage, switching-time, and absolute-maximum ratings before approving either part as a substitute.

コンプライアンス情報

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
鉛フリー
Unknown
ハロゲンフリー
Unknown
紛争鉱物
Unknown

No explicit RoHS, REACH, halogen-free, lead-free, conflict-minerals, or automotive-qualification statement appears in the product information used for this record. AEC-Q100 is not applicable to the documented general-purpose MAX339CSE+ ordering information.

データ検証日: 2026-11-18 — データはXAIPARTの部品エンジニアリングチームによって検証・管理されています

関連検索

MAX339CSE+ datasheet MAX339CSE+ pinout MAX339CSE+ datasheet pdf MAX339CSE+ equivalent MAX339CSE+ replacement MAX339CSE+ cross reference MAX339CSE+ price MAX339CSE+ stock Analog Devices MAX339CSE+ MAX339CSE+ 30V multiplexer MAX339CSE+ NSOIC-16 MAX339CSE+ vs MAX339ESE+

関連部品&用語

Analog Devices MAX339CSE+ MAX339ESE+ MAX339CSE MAX338 MAX339 DG508A DG509A analog multiplexer analog switch demultiplexer low-leakage CMOS dual 4:1 multiplexer 8-channel analog mux TTL-compatible control on-resistance leakage current charge injection 4.5 V to 30 V supply 16-pin NSOIC SOIC family surface-mount package 44 V silicon-gate process high-impedance instrumentation
クイック見積RFQ
詳細をすべてご記入ください — 営業チームが24時間以内にご返信いたします
部品番号 メーカー パッケージ QTY 目標価格 小計
✓
見積を送信しました!

24時間以内にメールでご返信いたします

1
RFQ送信済み
2
見積受領
3
注文済み
4
お支払い
5
発送済み
6
配達済み
RFQの詳細を表示