Analog Devices

MAX3490EESA+T - 12Mbps RS-485 Transceiver | Analog Devices

MPN: MAX3490EESA+T ✓ সক্রিয়
3.0V to 3.6V Vdss True RS-485 and RS-422 Rds(on) 8-pin SOIC Package
সর্বনিম্ন অর্ডার পরিমাণ: 1 |

MAX3490EESA+T সারাংশ

Analog Devices MAX3490EESA+T is a 3.3V-powered, single-channel RS-485/RS-422 transceiver with one driver and one receiver, supporting data rates up to 12Mbps in an 8-pin SOIC package. The MAX3490E combines true RS-485 and RS-422 operation with slew-rate-limited signaling and ±15kV ESD protection, making it appropriate for industrial communication links where both high throughput and surge robustness are required.

An RS-485/RS-422 transceiver is a physical-layer interface integrated circuit that converts logic-level signals into balanced differential bus voltages and converts incoming differential signals back into digital logic. The differential signaling improves common-mode noise immunity and allows reliable data transmission over longer cable runs. Positioned within the hierarchy of interface ICs, communications transceivers, and data-bus interface devices, the MAX3490E supports point-to-point RS-422 links as well as multi-drop RS-485 networks when the bus topology, termination, and biasing are designed correctly.

Principal features include a 3.3V supply, a maximum data rate of 12Mbps, ±15kV ESD protection, and slew-rate-limited driver outputs. The EESA variant provides an extended -40°C to +85°C operating range, while the +T suffix identifies the tape-and-reel ordering option. The device also includes a receiver with a fail-safe bias network, which helps determine a defined logic state when the bus is idle, disconnected, or shorted.

The MAX3490E architecture uses a differential driver and a differential receiver in one package, reducing board area compared with separate driver and receiver ICs. Slew-rate limiting reduces high-frequency EMI and helps suppress reflections on imperfectly terminated cables. Because the device supports both RS-485 and RS-422 standards, one transceiver can cover point-to-point industrial links, multidrop buses, motor-control networks, and data-acquisition equipment when the appropriate termination and idle-bias components are installed.

Typical applications include industrial PLC and factory-automation links, instrumentation buses, motor-driver control interfaces, building-automation equipment, and embedded data-acquisition systems. The 12Mbps capability supports demanding factory and motor-control traffic, while the 3.3V supply simplifies interfacing with modern low-voltage controllers, FPGAs, and microprocessors.

Design the bus network carefully: terminate both ends of a long RS-485 cable, avoid star branches, keep stub lengths short, and provide a bias resistor only at one location when the transceiver configuration requires idle biasing. Validate differential swing, common-mode range, isolation requirements, and ESD grounding before releasing the PCB layout.

এর জন্য ড্রপ-ইন বিকল্প MAX3490EESA+T — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।

এই সিরিজের ভ্যারিয়েন্ট

একই সিরিজের মডেল যেগুলো drop-in compatible MAX3490EESA+T (একই form factor এবং footprint) — পার্থক্য রয়েছে Driver Type, Package, Maximum Data Rate, Supply Voltage, Supported Standards.

Analog Devices
Driver Type: Slew-rate-limited true driver
Package: 8-pin NSOIC
Maximum Data Rate: 12 Mbps
এর সাথে তুলনা করুন MAX3490EESA+T →
Analog Devices
Package: 8-SOIC, 0.154 inch wide and 3.90 mm long
Maximum Data Rate: 10 Mbps
এর সাথে তুলনা করুন MAX3490EESA+T →
Analog Devices
Driver Type: Slew-rate-limited true RS-485/RS-422 driver
Supply Voltage: 3.3 V
Supported Standards: RS-422 and RS-485
এর সাথে তুলনা করুন MAX3490EESA+T →
Analog Devices
Maximum Data Rate: 12 Mbps
Supply Voltage: 3.3 V
এর সাথে তুলনা করুন MAX3490EESA+T →
Analog Devices
Driver Type: Slew-rate-limited differential driver
Maximum Data Rate: 12 Mbps
Supply Voltage: 3.3 V
এর সাথে তুলনা করুন MAX3490EESA+T →
Maxim Integrated
Driver Type: Slew-rate limited
Package: 8-SOIC
Supply Voltage: 3.3V
এর সাথে তুলনা করুন MAX3490EESA+T →
Analog Devices
Package: 8-SOIC
Maximum Data Rate: 10 Mbps
এর সাথে তুলনা করুন MAX3490EESA+T →

MAX3490CSA+

✅ ড্রপ-ইন
Analog Devices
📦 8-SOIC
RS-422/RS-485 interface transceiver · 3.3 V · 10 Mbps · 1 · 1 · RS-422 and RS-485 · Slew-rate-limited true RS-485/RS-422 driver · 8-pin SOIC

মূল্যের জন্য যোগাযোগ করুন

ডেটাশিট দেখুন →

MAX3490ECSA+

✅ ড্রপ-ইন
Analog Devices
📦 8-SOIC
RS-485/RS-422 transceiver · 3.3 V · 12 Mbps · 10 Mbps · ±15 kV · 1 driver · 1 receiver · RS-485 and RS-422

মূল্যের জন্য যোগাযোগ করুন

ডেটাশিট দেখুন →

MAX3491EESA+

✅ ড্রপ-ইন ⚠️ স্পেক যাচাইকৃত নয়
📦 8-SOIC
Same-family 8-pin SOIC transceiver with identical 3.3V, 12Mbps, ±15kV ESD, and extended-temperature positioning; enable-pin behavior must be checked

📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)

MAX3464ESA+

✅ ড্রপ-ইন
📦 8-SOIC
Related MAX346x 3.3V transceiver in the same 8-pin SOIC footprint; data rate and enable logic differ by up to 30%

📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)

MAX3469ESA+T

✅ ড্রপ-ইন
📦 8-SOIC
Related MAX346x transceiver in the same 8-pin SOIC package; lower-speed selection with different data-rate and enable characteristics

📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)

MAX3490EESA+T বিশেষণ

Product Type RS-485/RS-422 transceiver
Transceiver Configuration 1 transmitter and 1 receiver
সাপ্লাই ভোল্টেজ 3.0V to 3.6V
Maximum Data Rate 12Mbps
Distributor-Listed Data Rate 10Mbps
ESD Protection ±15kV
Driver Type Slew-rate-limited
Supported Standards True RS-485 and RS-422
অপারেটিং তাপমাত্রা -40°C to +85°C
প্যাকেজ 8-pin SOIC
মাউন্টিং টাইপ Surface Mount
Ordering Package Tape and Reel

MAX3490EESA+T tape and reel পিন কনফিগারেশন গাইড

MAX3490EESA+T (tape and reel প্যাকেজ)-এর পিন কনফিগারেশন। পিন নম্বরিং, ফাংশন এবং সংযোগ ডায়াগ্রাম প্রস্তুতকারকের ডেটাশিটে সংজ্ঞায়িত করা আছে। সঠিক ফুটপ্রিন্ট এবং সোল্ডারিং নির্দেশিকার জন্য এটি দেখুন।

MAX3490EESA+T-এর জন্য tape and reel প্যাকেজ পিনআউট ডায়াগ্রাম

এর জন্য বিস্তারিত পিনআউট ডেটা পাওয়া যায়নি MAX3490EESA+T.

দেখুন ডেটাশিট সম্পূর্ণ পিন কনফিগারেশনের জন্য।

সাধারণ ব্যবহার

MAX3490EESA+T এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Industrial PLC and Factory Automation, Motor Drive and Encoder Control, Instrumentation and Data Acquisition, Building Automation and Environmental Control, Embedded Controller and FPGA Communication, Long-Distance RS-422 Point-to-Point Link.

🏭

Industrial PLC and Factory Automation

The MAX3490EESA+T suits factory-control networks where a controller must communicate over a long industrial cable at a high data rate. Its 12Mbps maximum rate, 3.3V supply, and -40°C to +85°C operating range provide margin for temperature-variable environments, while the ±15kV ESD protection helps the bus interface tolerate industrial ESD events. Install 120-ohm termination at both ends of the trunk, keep device stubs short, and place any fail-safe bias network at one designated point. The slew-rate-limited driver reduces high-frequency EMI, but a linear daisy-chain layout remains necessary for reliable operation.

⚡

Motor Drive and Encoder Control

The MAX3490EESA+T can carry differential commands between a motor controller and external drive electronics over industrial cabling. Its 12Mbps data-rate capability provides headroom for position and status traffic, and the slew-rate-limited outputs help reduce EMI near power-conversion circuitry. The extended -40°C to +85°C range supports enclosure temperature variation. Because motor systems often experience large switching transients, follow the data-sheet grounding recommendations, keep the bus reference close to the transceiver, and verify the common-mode range of every connected node before deployment.

📊

Instrumentation and Data Acquisition

The MAX3490EESA+T is appropriate for laboratory and industrial measurement systems that distribute commands or collected data between remote instrumentation and a central controller. The combination of true RS-485/RS-422 operation and differential signaling improves noise immunity on cables running near motors and switching supplies. A 12Mbps bus rate supports burst-oriented transfer, while the 3.3V supply allows direct interfacing with modern controllers. Use isolated power and ground barriers where instruments float, and test the complete cable, connector, and termination network for reflections rather than relying on logic-level bench tests alone.

🏠

Building Automation and Environmental Control

The MAX3490EESA+T fits building-automation controllers, HVAC equipment, and environmental-monitoring nodes that exchange sensor readings and actuator commands over a wired RS-485 network. Its 12Mbps maximum data rate allows efficient polling and firmware-update traffic, and its -40°C to +85°C range covers equipment installed in unheated cabinets or variable-temperature spaces. The ±15kV ESD rating adds protection for exposed building-wiring interfaces. Keep cable routing away from mains wiring where possible, use a linear bus with termination only at the endpoints, and observe any single-point biasing requirement to prevent contention when multiple nodes transmit.

🖥️

Embedded Controller and FPGA Communication

The MAX3490EESA+T connects a 3.3V microprocessor, microcontroller, or FPGA to an external differential bus when the design requires a compact single-package driver-and-receiver solution. Combining both functions saves board area compared with separate ICs, while the 12Mbps capability supports moderately fast command and telemetry streams. The transceiver's logic-side enable pins should be driven only by signals with defined states during reset and power-up. Review propagation-delay and enable timing against the controller clock budget, and provide local bypassing close to the supply pins for dependable operation during fast edge rates.

🌐

Long-Distance RS-422 Point-to-Point Link

The MAX3490EESA+T supports true RS-422 point-to-point communication between two systems over a balanced cable, including industrial control and remote sensor links. The differential receiver rejects common-mode noise, and the 12Mbps maximum data rate provides useful margin over moderate-rate links. RS-422 does not permit the same multi-drop configuration as RS-485, so each driver should feed one receiver and the cable must be terminated appropriately at the source and load. Keep the interface ground reference close to the signal return and verify the full system common-mode range for long cables or ground-potential differences.

সুপারিশকৃত পণ্যের সারসংক্ষেপ

MAX3490CSA+ Analog Devices ব্যবহৃত হয়: Industrial PLC and Factory Automation, Instrumentation and Data Acquisition, Building Automation and Environmental Control, Long-Distance RS-422 Point-to-Point Link MAX3491EESA+ Related MAX349x RS-485/RS-422 interface in the same package family ব্যবহৃত হয়: Industrial PLC and Factory Automation, Building Automation and Environmental Control MAX3490ECSA+ Analog Devices ব্যবহৃত হয়: Motor Drive and Encoder Control, Embedded Controller and FPGA Communication MAX3469ESA+T Related differential bus transceiver for lower-speed control links ব্যবহৃত হয়: Motor Drive and Encoder Control, Long-Distance RS-422 Point-to-Point Link MAX3464ESA+ Related MAX346x transceiver for compatible differential data-acquisition links ব্যবহৃত হয়: Instrumentation and Data Acquisition, Embedded Controller and FPGA Communication
What is the MAX3490EESA+T used for?
The MAX3490EESA+T is a 3.3V-powered RS-485/RS-422 transceiver that provides one differential transmitter and one differential receiver in an 8-pin SOIC package. According to the Analog Devices MAX3490E product page, it is a slew-rate-limited, true RS-485/RS-422 device rated for data rates up to 12Mbps and protected to ±15kV ESD. It is suited to industrial links, motor-control networks, instrumentation, and data-acquisition systems.
What is the maximum data rate of the MAX3490EESA+T?
The MAX3490EESA+T supports a maximum data rate of 12Mbps according to the Analog Devices MAX3490E product page. One distributor listing identifies the same device as a 10Mbps RS-422/RS-485 transceiver, so system timing should be based on the manufacturer data sheet for the exact ordering code. The slew-rate-limited driver is intended to reduce EMI and cable reflections at high signaling rates.
Where can I download the MAX3490EESA+T datasheet PDF?
The official MAX3490EESA+T datasheet is available from the Analog Devices MAX3490E product page at analog.com. The manufacturer identifies the MAX3490E data sheet as Revision 1, and the device page includes the documentation, product-selection table, sample ordering information, and lifecycle status. Use the manufacturer PDF for the authoritative pin descriptions, electrical characteristics, and application guidance.
Where can I find the MAX3490EESA+T pinout?
The MAX3490EESA+T uses an 8-pin SOIC package, and its complete numbered pinout is shown in the pin-configuration section of the Analog Devices MAX3490E data sheet. The package contains the driver and receiver differential bus terminals, supply pins, ground pins, and driver-enable and receiver-enable controls. Use that table to assign PCB nets rather than relying on third-party package drawings.
Is the MAX3490EESA+T an RS-485 or RS-422 transceiver?
The MAX3490EESA+T supports both true RS-485 and RS-422 operation. According to the Analog Devices product page, it is a 3.3V-powered, slew-rate-limited, true RS-485/RS-422 transceiver with one driver and one receiver. The operating mode depends on bus topology, termination, idle-bias implementation, and how the enable inputs are driven.
What is the difference between MAX3490EESA+T and MAX3490CSA+?
The MAX3490CSA+ is the non-E temperature-grade member of the MAX3490 family, while the MAX3490EESA+T provides an extended -40°C to +85°C range. A component comparison identifies the CSA+ as a 15Mbps, 8-pin SOIC part with consistent terminals and package characteristics, supporting replacement without PCB changes. Choose the EESA+T when the industrial temperature range is required.
What is the difference between MAX3490EESA+T and MAX3490ECSA+?
The principal documented difference is the operating-temperature grade. A published comparison specifies -40°C to +85°C for the MAX3490EESA+T versus 0°C to +70°C for the MAX3490ECSA+, while both remain members of the MAX3490 family in the 8-pin SOIC format. The EESA+T is therefore the appropriate choice for industrial environments outside the commercial temperature range.
Can MAX3490CSA+ replace MAX3490EESA+T?
Yes, the MAX3490CSA+ can serve as a drop-in replacement when the commercial 0°C to +70°C operating range is acceptable. Cross-reference data describes its 8-pin SOIC terminals and package as consistent with the MAX3490EESA+T and identifies it as a complete replacement. The MAX3490CSA+ also offers a 15Mbps rating compared with the MAX3490EESA+T's 12Mbps manufacturer rating.
When should I choose the MAX3490EESA+T over the MAX3490CSA+?
Choose the MAX3490EESA+T when the equipment must operate across -40°C to +85°C, particularly in industrial automation, factory control, or motor-drive environments. The MAX3490CSA+ is appropriate where a 0°C to +70°C range is adequate. Both use an 8-pin SOIC package, so the choice is primarily temperature grade, qualification requirements, and production availability.
Is the MAX3490EESA+T suitable for industrial factory automation?
Yes, the MAX3490EESA+T fits industrial factory-automation links that require a 3.3V interface, high data throughput, and robust differential signaling. Its 12Mbps maximum data rate, slew-rate-limited driver, ±15kV ESD protection, and -40°C to +85°C operating range support demanding bus traffic. Cable termination, grounding, and bus topology remain essential to reliable operation.
What can replace the MAX3490EESA+T?
The MAX3490CSA+ is the clearest drop-in replacement because it uses the same 8-pin SOIC format and is described as having consistent terminals and package characteristics. The MAX3490ECSA+ is another family member with the same package but a narrower 0°C to +70°C temperature range. Verify the required temperature grade, data rate, enable logic, and supply constraints before substituting either part.
What is the best Analog Devices alternative for the MAX3490EESA+T?
Analog Devices MAX3490CSA+ is the closest documented alternative for applications operating from 0°C to +70°C. It retains the 8-pin SOIC footprint, is identified as a complete replacement, and is rated for 15Mbps versus the MAX3490EESA+T's 12Mbps rating. For designs requiring -40°C to +85°C operation, retaining the MAX3490EESA+T avoids a temperature-grade downgrade.
Does the MAX3490EESA+T need external termination resistors?
External termination is generally required at both ends of a long RS-485 cable to control reflections, while RS-422 point-to-point links also benefit from proper source and load termination. The MAX3490EESA+T provides the active differential drivers and receivers, not the cable termination network. Place termination close to the bus endpoints and follow the data-sheet application guidance for resistor values and bus loading.
How should an RS-485 bus be configured around the MAX3490EESA+T?
Configure the MAX3490EESA+T network as a linear daisy chain, terminate both physical ends, and keep branch stubs short. Use only one designated bias location when fail-safe idle biasing is needed, and drive the driver-enable and receiver-enable inputs according to the intended half-duplex direction control. Star topologies and long unterminated stubs increase reflection and common-mode risks.
Where can I buy the MAX3490EESA+T and check its lead time?
Use the Request a Quote form on this page to ask about MAX3490EESA+T availability, current lead time, and minimum order quantity. The manufacturer lists the MAX3490E family as in production, but live inventory and lead time vary by order quantity and market conditions. The +T ordering option is supplied in tape-and-reel format.
What are the key specifications engineers should know about MAX3490EESA+T?
The key MAX3490EESA+T specifications are a 3.0V to 3.6V supply, one driver and one receiver, true RS-485/RS-422 operation, a 12Mbps maximum data rate, ±15kV ESD protection, and a -40°C to +85°C operating range. It is packaged in an 8-pin SOIC and uses slew-rate-limited outputs. These specifications make it suitable for high-speed, noise-tolerant industrial differential-bus links.

এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা MAX3490EESA+T — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।

নির্বাচন গাইড

Choose the MAX3490EESA+T when the design requires a 3.3V RS-485/RS-422 interface with up to 12Mbps operation, ±15kV ESD protection, and operation from -40°C to +85°C. It is the appropriate choice for industrial controllers, motor systems, and exposed building-wiring interfaces. Select the MAX3490CSA+ when the same 8-SOIC footprint is needed but the 0°C to +70°C commercial range is sufficient; its 15Mbps rating also exceeds the target's 12Mbps rating. The MAX3490ECSA+ is another same-package option with the narrower commercial temperature range. MAX3491EESA+ belongs to the related MAX349x family and should be selected only after confirming enable behavior and system timing. Use MAX3464ESA+ or MAX3469ESA+T only when their lower-speed characteristics still satisfy the bus timing budget. In every case, verify the exact electrical limits, enable polarity, and bus biasing requirements against the manufacturer data sheet.

বিকল্পের সাথে তুলনা

পারামিটার এই পণ্য MAX3490CSA+ MAX3490ECSA+ MAX3491EESA+ MAX3464ESA+ MAX3469ESA+T
Brand Analog Devices / Maxim Integrated Analog Devices / Maxim Integrated Analog Devices / Maxim Integrated Analog Devices / Maxim Integrated Analog Devices / Maxim Integrated Analog Devices / Maxim Integrated
Package 8-SOIC 8-SOIC 8-SOIC 8-SOIC 8-SOIC 8-SOIC
Supply Voltage 3.0V to 3.6V 3.0V to 3.6V 3.0V to 3.6V 3.0V to 3.6V 3.0V to 3.6V 3.0V to 3.6V

মূল পার্থক্যসমূহ

  • Extended-temperature operation with a 12Mbps interface (বনামMAX3490CSA+)
  • Higher data-rate rating than the commercial-grade family member (বনামMAX3490CSA+)
  • Same package and bus interface as related MAX3490 options (বনামMAX3490ECSA+)
  • Compact integrated driver and receiver (বনামMAX3469ESA+T)

ডিজাইন নোট

Route the MAX3490EESA+T differential bus as a short, tightly coupled pair and connect the interface ground reference to the logic ground through the layout recommended by the data sheet. Keep connector and protection-device paths ahead of the transceiver so surge current is diverted away from the IC. Avoid routing the bus parallel to switching-node edges or high-current motor conductors, and maintain a continuous ground reference beneath the interface section.

Do not terminate an RS-485 bus at every node: install termination only at the two physical ends of the trunk, and keep stubs short. For idle-bias arrangements, place the fail-safe bias network at one designated location to avoid multiple devices fighting on the bus. Star branches and long unterminated cables can produce reflections that appear as intermittent communication errors even when the transceiver itself is operating correctly.

The 12Mbps rating is the upper communications-rate limit, not a guarantee that every cable installation will close cleanly at that rate. Derive the usable rate from cable length, propagation delay, connector impedance, topology, and the allowed receiver timing. Place bypass capacitance close to the supply pins, validate differential input and common-mode limits over the complete system, and use high-speed differential measurement techniques when troubleshooting a marginal link.

কমপ্লায়েন্স তথ্য

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
লিড ফ্রি
Unknown
হ্যালোজেন ফ্রি
Unknown
কনফ্লিক্ট মিনারেলস
Unknown

The manufacturer identifies the MAX3490E family as being in production, but specific RoHS, REACH, halogen-free, and conflict-minerals statements were not established from the cited product information. AEC-Q100 qualification is not indicated for this commercial interface IC.

ডেটা যাচাই করা হয়েছে: 2026-11-09 — ডেটা XAIPART-এর কম্পোনেন্ট ইঞ্জিনিয়ারিং টিম দ্বারা যাচাই ও কিউরেট করা হয়েছে

সম্পর্কিত অনুসন্ধান

MAX3490EESA+T datasheet MAX3490EESA+T datasheet pdf MAX3490EESA+T pinout MAX3490EESA+T equivalent MAX3490EESA+T drop-in replacement MAX3490EESA+T vs MAX3490CSA+ MAX3490EESA+T price MAX3490EESA+T stock Analog Devices MAX3490EESA+T MAX3490E 12Mbps RS-485 transceiver MAX3490EESA 8-SOIC pinout MAX3490EESA industrial RS-422 MAX3490EESA ESD protection MAX3490EESA cross reference

সম্পর্কিত কম্পোনেন্ট ও শর্তাবলী

Analog Devices Maxim Integrated MAX3490EESA+T MAX3490E MAX3490CSA+ MAX3490ECSA+ MAX3491EESA+ MAX3464ESA+ MAX3469ESA+T RS-485 transceiver RS-422 transceiver communications transceiver interface IC differential signaling balanced bus slew-rate-limited driver fail-safe bias 12Mbps data rate 3.3V power supply ±15kV ESD protection 8-SOIC package surface-mount package factory automation industrial PLC motor control
তাৎক্ষণিক বিলওয়াছে রেকোজিউইট
সম্পূর্ণ বিবরণ পূরণ করুন — আমাদের সেলস টিম 24 ঘণ্টার মধ্যে উত্তর দেবে
পার্ট নম্বর উৎপাদক প্যাকেজ QTY লক্ষ্যমূল্য প্রসারিত
✓
বিল প্রস্তুত করা হয়েছে!

আমরা ২৪ ঘণ্টার মধ্যে আপনার ইমেইলে প্রত্যুত্তর দেব

1
RFQ জমা হয়েছে
2
কোটেশন পাওয়া গেছে
3
অর্ডার দেওয়া হয়েছে
4
পেমেন্ট
5
শিপ করা হয়েছে
6
ডেলিভারি হয়েছে
RFQ বিবরণ দেখুন