MAX3490EESA+T - 12Mbps RS-485 Transceiver | Analog Devices
料号: MAX3490EESA+T ✓ 量产中MAX3490EESA+T 概述
An RS-485/RS-422 transceiver is a physical-layer interface integrated circuit that converts logic-level signals into balanced differential bus voltages and converts incoming differential signals back into digital logic. The differential signaling improves common-mode noise immunity and allows reliable data transmission over longer cable runs. Positioned within the hierarchy of interface ICs, communications transceivers, and data-bus interface devices, the MAX3490E supports point-to-point RS-422 links as well as multi-drop RS-485 networks when the bus topology, termination, and biasing are designed correctly.
Principal features include a 3.3V supply, a maximum data rate of 12Mbps, ±15kV ESD protection, and slew-rate-limited driver outputs. The EESA variant provides an extended -40°C to +85°C operating range, while the +T suffix identifies the tape-and-reel ordering option. The device also includes a receiver with a fail-safe bias network, which helps determine a defined logic state when the bus is idle, disconnected, or shorted.
The MAX3490E architecture uses a differential driver and a differential receiver in one package, reducing board area compared with separate driver and receiver ICs. Slew-rate limiting reduces high-frequency EMI and helps suppress reflections on imperfectly terminated cables. Because the device supports both RS-485 and RS-422 standards, one transceiver can cover point-to-point industrial links, multidrop buses, motor-control networks, and data-acquisition equipment when the appropriate termination and idle-bias components are installed.
Typical applications include industrial PLC and factory-automation links, instrumentation buses, motor-driver control interfaces, building-automation equipment, and embedded data-acquisition systems. The 12Mbps capability supports demanding factory and motor-control traffic, while the 3.3V supply simplifies interfacing with modern low-voltage controllers, FPGAs, and microprocessors.
Design the bus network carefully: terminate both ends of a long RS-485 cable, avoid star branches, keep stub lengths short, and provide a bias resistor only at one location when the transceiver configuration requires idle biasing. Validate differential swing, common-mode range, isolation requirements, and ESD grounding before releasing the PCB layout.
直接替换替代料: MAX3490EESA+T ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: MAX3490EESA+T (相同外形与封装尺寸) ——差异在于 Driver Type, Package, Maximum Data Rate, Supply Voltage, Supported Standards.
MAX3490CSA+
✅ 直接替换联系询价
查看数据手册 →MAX3490ECSA+
✅ 直接替换联系询价
查看数据手册 →MAX3491EESA+
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
MAX3464ESA+
✅ 直接替换📋 参考替代料(不在目录中)
MAX3469ESA+T
✅ 直接替换📋 参考替代料(不在目录中)
MAX3490EESA+T 规格参数
| Product Type | RS-485/RS-422 transceiver |
| Transceiver Configuration | 1 transmitter and 1 receiver |
| 电源电压 | 3.0V to 3.6V |
| Maximum Data Rate | 12Mbps |
| Distributor-Listed Data Rate | 10Mbps |
| ESD Protection | ±15kV |
| Driver Type | Slew-rate-limited |
| Supported Standards | True RS-485 and RS-422 |
| 工作温度 | -40°C to +85°C |
| 封装 | 8-pin SOIC |
| 安装类型 | Surface Mount |
| Ordering Package | Tape and Reel |
MAX3490EESA+T tape and reel 引脚配置指南
MAX3490EESA+T(tape and reel 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: MAX3490EESA+T.
请参阅 数据手册 以查看完整引脚配置。
典型应用
MAX3490EESA+T 适用于 6 应用s: Industrial PLC and Factory Automation, Motor Drive and Encoder Control, Instrumentation and Data Acquisition, Building Automation and Environmental Control, Embedded Controller and FPGA Communication, Long-Distance RS-422 Point-to-Point Link.
Industrial PLC and Factory Automation
The MAX3490EESA+T suits factory-control networks where a controller must communicate over a long industrial cable at a high data rate. Its 12Mbps maximum rate, 3.3V supply, and -40°C to +85°C operating range provide margin for temperature-variable environments, while the ±15kV ESD protection helps the bus interface tolerate industrial ESD events. Install 120-ohm termination at both ends of the trunk, keep device stubs short, and place any fail-safe bias network at one designated point. The slew-rate-limited driver reduces high-frequency EMI, but a linear daisy-chain layout remains necessary for reliable operation.
推荐
Motor Drive and Encoder Control
The MAX3490EESA+T can carry differential commands between a motor controller and external drive electronics over industrial cabling. Its 12Mbps data-rate capability provides headroom for position and status traffic, and the slew-rate-limited outputs help reduce EMI near power-conversion circuitry. The extended -40°C to +85°C range supports enclosure temperature variation. Because motor systems often experience large switching transients, follow the data-sheet grounding recommendations, keep the bus reference close to the transceiver, and verify the common-mode range of every connected node before deployment.
推荐
Instrumentation and Data Acquisition
The MAX3490EESA+T is appropriate for laboratory and industrial measurement systems that distribute commands or collected data between remote instrumentation and a central controller. The combination of true RS-485/RS-422 operation and differential signaling improves noise immunity on cables running near motors and switching supplies. A 12Mbps bus rate supports burst-oriented transfer, while the 3.3V supply allows direct interfacing with modern controllers. Use isolated power and ground barriers where instruments float, and test the complete cable, connector, and termination network for reflections rather than relying on logic-level bench tests alone.
推荐
Building Automation and Environmental Control
The MAX3490EESA+T fits building-automation controllers, HVAC equipment, and environmental-monitoring nodes that exchange sensor readings and actuator commands over a wired RS-485 network. Its 12Mbps maximum data rate allows efficient polling and firmware-update traffic, and its -40°C to +85°C range covers equipment installed in unheated cabinets or variable-temperature spaces. The ±15kV ESD rating adds protection for exposed building-wiring interfaces. Keep cable routing away from mains wiring where possible, use a linear bus with termination only at the endpoints, and observe any single-point biasing requirement to prevent contention when multiple nodes transmit.
推荐
Embedded Controller and FPGA Communication
The MAX3490EESA+T connects a 3.3V microprocessor, microcontroller, or FPGA to an external differential bus when the design requires a compact single-package driver-and-receiver solution. Combining both functions saves board area compared with separate ICs, while the 12Mbps capability supports moderately fast command and telemetry streams. The transceiver's logic-side enable pins should be driven only by signals with defined states during reset and power-up. Review propagation-delay and enable timing against the controller clock budget, and provide local bypassing close to the supply pins for dependable operation during fast edge rates.
推荐
Long-Distance RS-422 Point-to-Point Link
The MAX3490EESA+T supports true RS-422 point-to-point communication between two systems over a balanced cable, including industrial control and remote sensor links. The differential receiver rejects common-mode noise, and the 12Mbps maximum data rate provides useful margin over moderate-rate links. RS-422 does not permit the same multi-drop configuration as RS-485, so each driver should feed one receiver and the cable must be terminated appropriately at the source and load. Keep the interface ground reference close to the signal return and verify the full system common-mode range for long cables or ground-potential differences.
推荐
推荐产品汇总
工程参考数据: MAX3490EESA+T ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | MAX3490CSA+ | MAX3490ECSA+ | MAX3491EESA+ | MAX3464ESA+ | MAX3469ESA+T |
|---|---|---|---|---|---|---|
| Brand | Analog Devices / Maxim Integrated | Analog Devices / Maxim Integrated | Analog Devices / Maxim Integrated | Analog Devices / Maxim Integrated | Analog Devices / Maxim Integrated | Analog Devices / Maxim Integrated |
| Package | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC |
| Supply Voltage | 3.0V to 3.6V | 3.0V to 3.6V | 3.0V to 3.6V | 3.0V to 3.6V | 3.0V to 3.6V | 3.0V to 3.6V |
关键差异点
- Extended-temperature operation with a 12Mbps interface (对比 MAX3490CSA+)
- Higher data-rate rating than the commercial-grade family member (对比 MAX3490CSA+)
- Same package and bus interface as related MAX3490 options (对比 MAX3490ECSA+)
- Compact integrated driver and receiver (对比 MAX3469ESA+T)
设计说明
Route the MAX3490EESA+T differential bus as a short, tightly coupled pair and connect the interface ground reference to the logic ground through the layout recommended by the data sheet. Keep connector and protection-device paths ahead of the transceiver so surge current is diverted away from the IC. Avoid routing the bus parallel to switching-node edges or high-current motor conductors, and maintain a continuous ground reference beneath the interface section.
Do not terminate an RS-485 bus at every node: install termination only at the two physical ends of the trunk, and keep stubs short. For idle-bias arrangements, place the fail-safe bias network at one designated location to avoid multiple devices fighting on the bus. Star branches and long unterminated cables can produce reflections that appear as intermittent communication errors even when the transceiver itself is operating correctly.
The 12Mbps rating is the upper communications-rate limit, not a guarantee that every cable installation will close cleanly at that rate. Derive the usable rate from cable length, propagation delay, connector impedance, topology, and the allowed receiver timing. Place bypass capacitance close to the supply pins, validate differential input and common-mode limits over the complete system, and use high-speed differential measurement techniques when troubleshooting a marginal link.
合规信息
The manufacturer identifies the MAX3490E family as being in production, but specific RoHS, REACH, halogen-free, and conflict-minerals statements were not established from the cited product information. AEC-Q100 qualification is not indicated for this commercial interface IC.