Maxim Integrated

MAX362EPE - 4-Channel 85Ω SPST Analog Switch | Maxim

MPN: MAX362EPE ✗ জীবনকালের সমাপ্তি
85 ohm Rds(on) 16-pin PDIP Package
সর্বনিম্ন অর্ডার পরিমাণ: 1 |

MAX362EPE সারাংশ

Maxim MAX362EPE is a precision quad-channel, single-pole single-throw analog switch with four normally open circuits, an 85 Ω on resistance, and a 16-pin PDIP package. The device provides 1:1 signal routing for four independent analog channels and is packaged for through-hole PCB assembly rather than surface mounting.

An analog switch is a semiconductor device that connects or disconnects an analog signal path under digital control. The SPST architecture provides one selectable path for each circuit, while the quad configuration integrates four independent switches into one package. Within the signal-path hierarchy, MAX362EPE belongs to the analog switch and multiplexing category, where low on resistance, predictable channel behavior, and control-signal compatibility are central design considerations.

The MAX362EPE differentiates itself through its four normally open switch functions and listed 85 Ω on resistance. Its 1:1 configuration preserves signal polarity rather than inverting the selected path. The device is listed in an industrial temperature grade and uses a rectangular PDIP-16 package. Four independent control inputs allow a microcontroller or logic circuit to route separate analog nodes without requiring a separate single-channel package for each function.

The MAX361 and MAX362 share the same precision quad-SPST family, but their default contact states differ. MAX362 uses normally open switches, which leave each channel disconnected until the corresponding control signal asserts the connection. This behavior is useful when signal isolation during reset or power-up is required. Exact voltage ratings, leakage currents, channel-to-channel resistance matching, switching-time limits, and absolute maximum conditions should be confirmed in the manufacturer datasheet before a new design is released.

Typical uses include multiplexed sensor acquisition, instrumentation signal routing, test-equipment input selection, industrial control interfaces, and precision analog measurement systems. In these applications, the four switch channels can reduce the number of discrete relays or routing components while allowing software-controlled path selection. Engineers must still check the signal amplitude, bandwidth, leakage, and control-logic thresholds against the complete operating specification.

A practical design consideration is to route each analog trace away from fast digital or switching-regulator nodes, and to place any protection or filtering components close to the connector or source. Because the MAX362EPE uses normally open contacts, system startup and fault-response logic should account for the unasserted state. Confirm the complete pin mapping and control polarity against the manufacturer datasheet before laying out a board.

This product page consolidates the exact MPN identity, package information, lifecycle information, commercial ordering path, and available drop-in comparison for the obsolete MAX362EPE. It also adds practical guidance on analog-signal integrity, default switch state, control sequencing, and the checks required when replacing legacy through-hole analog switches.

এর জন্য ড্রপ-ইন বিকল্প MAX362EPE — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।

এই সিরিজের ভ্যারিয়েন্ট

একই সিরিজের মডেল যেগুলো drop-in compatible MAX362EPE (একই form factor এবং footprint) — পার্থক্য রয়েছে Package, Temperature Grade.

Maxim Integrated
Package: 16-PDIP
Temperature Grade: Commercial grade
এর সাথে তুলনা করুন MAX362EPE →

MAX362CPE+

✅ ড্রপ-ইন
Analog Devices
📦 PDIP-16
4 circuits · 4 independent SPST channels · 1:1 · Normally open (NO) · 85 ohm · Within 2 ohm · 9 ohm · 16-pin PDIP

মূল্যের জন্য যোগাযোগ করুন

ডেটাশিট দেখুন →

MAX362EPE সর্বোচ্চ রেটিং ও বৈদ্যুতিক বৈশিষ্ট্য

Number of Circuits 4 circuits
Switch Type Single-pole single-throw (SPST)
Default Contact State Normally open (NO)
Channel-to-Channel Ratio 1:1
On Resistance 85 ohm
Technology CMOS
প্যাকেজ 16-pin PDIP
Package Type PDIP-16 through-hole
Package Shape Rectangular
Surface Mount No
Temperature Grade Industrial
Number of Terminals 16 terminals

MAX362EPE rectangular পিন কনফিগারেশন গাইড

MAX362EPE (rectangular প্যাকেজ)-এর পিন কনফিগারেশন। পিন নম্বরিং, ফাংশন এবং সংযোগ ডায়াগ্রাম প্রস্তুতকারকের ডেটাশিটে সংজ্ঞায়িত করা আছে। সঠিক ফুটপ্রিন্ট এবং সোল্ডারিং নির্দেশিকার জন্য এটি দেখুন।

MAX362EPE-এর জন্য rectangular প্যাকেজ পিনআউট ডায়াগ্রাম

এর জন্য বিস্তারিত পিনআউট ডেটা পাওয়া যায়নি MAX362EPE.

দেখুন ডেটাশিট সম্পূর্ণ পিন কনফিগারেশনের জন্য।

সাধারণ ব্যবহার

MAX362EPE এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Multiplexed Sensor Acquisition, Precision Test and Measurement, Industrial Control Signal Routing, Communication and Data Acquisition, Audio and Measurement Path Selection, Legacy Peripheral Signal Multiplexing.

🏭

Multiplexed Sensor Acquisition

The MAX362EPE can route four sensor signals through a shared analog front end while its normally open contacts keep each channel isolated until explicitly enabled. The listed 85 Ω on resistance provides a defined series impedance for the selected path, while four independent control inputs simplify microcontroller-controlled channel selection. This arrangement is useful in industrial monitoring systems that must scan temperature, pressure, and level transducers through one measurement chain. Before implementation, verify that the sensor excitation range, source impedance, leakage, and settling time remain acceptable after the switch and its surrounding acquisition circuitry are included.

🔧

Precision Test and Measurement

MAX362EPE fits instrument front ends that must select among several analog inputs without using a separate switch package for every channel. Its four 1:1 SPST paths preserve signal polarity, while the normally open state provides a defined disconnected condition before measurement begins. The 85 Ω on resistance is relevant when calculating source impedance, attenuation, and amplifier-input interactions. Engineers should confirm the complete signal bandwidth, charge injection, off leakage, and switching-time specifications against the highest expected source impedance and shortest required measurement interval.

🏭

Industrial Control Signal Routing

The MAX362EPE can provide software-controlled selection of four industrial analog command or feedback paths when the controller requires independent, isolated connections. Its normally open switch behavior supports fail-safe logic if the control firmware leaves every channel deasserted during initialization or fault handling. The 16-pin PDIP package is appropriate for through-hole legacy and industrial-control boards. Design review should cover the maximum switched voltage, control thresholds, surge exposure, and the effect of the 85 Ω path resistance on actuator or feedback-network calculations.

🌐

Communication and Data Acquisition

The MAX362EPE is suitable for older communication equipment that uses four switched analog branches feeding a shared converter or transceiver path. Independent control inputs permit channel selection from digital logic, while the 1:1 configuration avoids signal inversion. Its 85 Ω on resistance contributes to the total source impedance seen by the receiving circuit and must be included in gain and bandwidth analysis. Because this is a legacy through-hole device, maintainers should also check system-level grounding, connector transients, and nearby switching-supply noise before reusing the existing board architecture.

🎧

Audio and Measurement Path Selection

MAX362EPE can select among four low-level analog sources in measurement equipment when each source must remain disconnected until selected. The normally open contacts prevent unintended signal paths from loading shared circuitry during setup, while the 85 Ω on resistance must be included in the source-impedance and noise analysis. The device is most appropriate for controlled, legacy-style signal routing rather than high-bandwidth audio multiplexing. Confirm off-state isolation, channel matching, maximum input amplitude, and control-signal behavior in the manufacturer datasheet before finalizing the audio-path topology.

🧩

Legacy Peripheral Signal Multiplexing

The MAX362EPE offers a compact through-hole way to multiplex four peripheral signals in legacy embedded systems. Its quad arrangement reduces the number of separate single-switch packages, and independent control inputs can be driven from a microcontroller or latch. The normally open topology can simplify reset-state behavior by leaving external lines disconnected until the system has completed initialization. Validate voltage levels, source impedance, leakage into adjacent circuits, and switching transients against the original system requirements, particularly when modern low-power peripherals are connected to the same analog node.

What is the MAX362EPE?
The MAX362EPE is a Maxim precision quad analog switch containing four independent, normally open SPST circuits in a 16-pin PDIP package. Its listed on resistance is 85 Ω, and each channel provides a 1:1 signal path. The four control inputs allow a digital controller to connect four analog signals independently. According to the MAX362EPE datasheet description, the device is intended for precision analog routing applications.
What are the key specifications of MAX362EPE that engineers should know?
The MAX362EPE provides four normally open SPST switch functions, an 85 Ω on resistance, a 1:1 signal configuration, CMOS construction, and a 16-pin PDIP package. It is listed as an industrial-grade, non-surface-mount device. According to the MAX362EPE datasheet and component listing, these characteristics make it suitable for through-hole precision analog-routing designs requiring four independent switched paths.
Is MAX362EPE normally open or normally closed?
The MAX362EPE contains four normally open switches, so each analog path remains disconnected until its control input activates the corresponding channel. This differs from the MAX361 family member, which uses normally closed contacts. According to the MAX361/MAX362 family description, the normally open behavior of MAX362 is useful when a disconnected or isolated signal path is required during reset.
Where can I download the MAX362EPE datasheet PDF?
The MAX362EPE datasheet PDF can be accessed through the MAX362EPE datasheet page linked on this product page. The document is titled “Precision, Quad, SPST Analog Switches” and covers the MAX361/MAX362 family. Use the manufacturer datasheet pin-description table when assigning PCB signals and verify voltage, leakage, switching-time, and absolute-maximum ratings before production release.
Where can I find the MAX362EPE pinout?
The MAX362EPE pin assignment is documented in the manufacturer datasheet’s pin-description and ordering-information sections. The exact numbered pin names are not reproduced on this page because a complete manufacturer pin table was not available. Use the MAX362EPE datasheet to map the four control inputs, four analog pairs, power pins, and ground connections before laying out a replacement board.
Where can I buy MAX362EPE online?
You can request a quote for the MAX362EPE through the “Request a Quote” form on this page. The part is an obsolete Maxim device in a 16-pin PDIP package, so availability can vary for legacy inventory. Provide the required quantity, assembly packaging preference, and target delivery location with the request to obtain the current sourcing response.
What is the price of MAX362EPE?
The current commercial price for the MAX362EPE should be requested through the “Request a Quote” form on this page. The device is listed as obsolete, and legacy inventory may have different quantity breaks, test status, or packaging conditions. Submit your required quantity and any acceptable manufacturer or traceability requirements so the quote can reflect the exact MAX362EPE orderable configuration.
What is the lead time for MAX362EPE?
The current lead time for the obsolete MAX362EPE should be confirmed through the “Request a Quote” form on this page. Lead time depends on remaining factory, distributor, or excess-stock inventory and can differ by order quantity. Include the required delivery date and annual usage in the request, and request an update if the part becomes unavailable.
Is MAX362EPE in stock?
Stock status for the obsolete MAX362EPE must be confirmed through the “Request a Quote” form on this page. The device has historically appeared in catalog and legacy inventory channels, but that does not establish current availability or traceability. Request a quantity-specific stock confirmation and include any date-code, inspection, or assembly requirements.
What can replace MAX362EPE?
The MAX362CPE+ is the closest listed drop-in candidate because it retains the four-channel normally open SPST configuration, 85 Ω on resistance, 1:1 routing, and 16-pin PDIP package. Its temperature-grade suffix differs from the MAX362EPE, so engineers should verify the required commercial or industrial temperature range before substitution. Use the “Request a Quote” form to confirm availability of the exact replacement MPN.
Is MAX362EPE the same as MAX362CPE+?
The MAX362EPE and MAX362CPE+ share the key routing architecture and package: four normally open SPST switches, 85 Ω on resistance, 1:1 configuration, and a 16-pin PDIP outline. Their E and C suffix designations identify different temperature grades, making the C-grade part unsuitable for some industrial environments. Confirm the operating-temperature requirement and pin mapping before treating it as a drop-in replacement.
MAX362EPE vs MAX362CPE+ - which is better for an industrial design?
The MAX362EPE is generally the better match for an industrial-temperature requirement because its E suffix denotes the industrial temperature grade, while MAX362CPE+ carries the commercial-grade designation. Both use the same four-channel, normally open SPST architecture, 85 Ω on resistance, and 16-pin PDIP package. The final choice depends on minimum and maximum ambient-temperature requirements and verified operating limits.
When should I choose MAX362EPE over MAX362CPE+?
Choose MAX362EPE when the board must operate across the industrial temperature range and the MAX362EPE’s E-grade status is required by the system specification. Choose MAX362CPE+ when the equipment operates only within commercial-temperature limits and a currently sourced legacy alternative is preferable. Both parts use the same 16-pin PDIP footprint and four normally open switch channels.
Is MAX362EPE suitable for instrumentation and sensor measurement?
The MAX362EPE is suitable for instrumentation and sensor-routing designs that require four independent, normally open analog paths at an 85 Ω on resistance. The normally open state also provides isolation until the control logic enables a channel. Verify the actual sensor voltage, leakage, bandwidth, injection current, and switching timing against the complete datasheet before using it in high-impedance measurement circuits.
How should MAX362EPE control inputs and analog traces be routed?
Route each MAX362EPE analog path with a short, continuous trace and keep it separated from clocks, high-current switching nodes, and other sources of injection noise. Connect the control signals through clean logic paths and ensure their levels meet the device’s input thresholds. Because the switches are normally open, also define the intended state during reset, power-up, and firmware initialization.

এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা MAX362EPE — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।

নির্বাচন গাইড

Choose MAX362EPE when maintaining an industrial-temperature, through-hole design that requires four independent normally open SPST analog channels and an 85 Ω on resistance. Its obsolete lifecycle status means procurement should be coordinated with the “Request a Quote” form on this page, including quantity, traceability, and date-code requirements. MAX362CPE+ is the closest listed drop-in option because it retains the same 16-pin PDIP package, four-channel normally open architecture, 85 Ω on resistance, and 1:1 configuration. Select it only when the commercial temperature grade is acceptable and its lifecycle status is suitable for the intended program. No other verified same-package alternatives were identified, so do not substitute an analog-multiplexer or relay with a different pinout without accepting a PCB redesign.

বিকল্পের সাথে তুলনা

পারামিটার এই পণ্য MAX362CPE+
Package PDIP-16 PDIP-16
Brand Maxim Integrated Maxim Integrated
Number of Circuits 4 circuits 4 circuits
Switch Type Single-pole single-throw (SPST) Single-pole single-throw (SPST)
Default Contact State Normally open Normally open
On Resistance 85 ohm 85 ohm
Channel-to-Channel Ratio 1:1 1:1
Temperature Grade Industrial Commercial
Mounting Type Through-hole Through-hole

মূল পার্থক্যসমূহ

  • Four independent normally open analog paths (বনামMAX362CPE+)
  • Industrial-grade temperature classification (বনামMAX362CPE+)
  • Established through-hole footprint (বনামMAX362CPE+)

ডিজাইন নোট

Keep each switched analog path short and place any termination, filtering, or clamping components close to the signal source or connector. Treat the 85 Ω on resistance as part of the complete source impedance seen by the next amplifier or converter. Avoid routing sensitive nodes beside digital control lines, clock outputs, and high-current switching paths, because capacitive coupling through the control and power pins can create errors even when the switch is in its open state.

Define the power-up and reset behavior explicitly because all four MAX362EPE channels are normally open. Pull control inputs to a defined inactive state if the supervising controller can tri-state or reset unexpectedly, and avoid floating control inputs. Confirm the device’s supply range, control thresholds, and quiescent behavior from the manufacturer datasheet, then calculate the supply current required by the surrounding system before assigning the analog and digital ground connections.

Do not assume that a 16-pin PDIP replacement is interchangeable solely because its outline matches. MAX362CPE+ retains the listed 85 Ω, four-channel normally open SPST configuration, but its commercial temperature grade differs from the MAX362EPE industrial grade. Confirm minimum and maximum ambient temperature, control polarity, pin names, electrical limits, and obsolete-part availability before approving it as a drop-in substitute.

কমপ্লায়েন্স তথ্য

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
লিড ফ্রি
Unknown
হ্যালোজেন ফ্রি
Unknown
কনফ্লিক্ট মিনারেলস
Unknown

No specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals statement was identified for the exact MAX362EPE ordering code. AEC-Q100 is not applicable because this is an industrial analog interface switch rather than an automotive-qualified device.

ডেটা যাচাই করা হয়েছে: 2026-11-19 — ডেটা XAIPART-এর কম্পোনেন্ট ইঞ্জিনিয়ারিং টিম দ্বারা যাচাই ও কিউরেট করা হয়েছে

সম্পর্কিত অনুসন্ধান

MAX362EPE datasheet MAX362EPE pinout MAX362EPE datasheet pdf MAX362EPE equivalent MAX362EPE replacement MAX362EPE cross reference MAX362EPE vs MAX362CPE+ MAX362EPE PDIP-16 footprint Maxim MAX362EPE MAX362EPE price MAX362EPE stock MAX362EPE application circuit

সম্পর্কিত কম্পোনেন্ট ও শর্তাবলী

Maxim Integrated MAX362EPE MAX362CPE+ MAX361 MAX362 analog switch SPST switch normally open switch quad analog switch analog multiplexing interface IC CMOS on resistance 85 ohm 1:1 signal routing PDIP-16 through-hole package industrial temperature grade multiplexed sensor acquisition test and measurement signal integrity obsolete component XAI PART
তাৎক্ষণিক বিলওয়াছে রেকোজিউইট
সম্পূর্ণ বিবরণ পূরণ করুন — আমাদের সেলস টিম 24 ঘণ্টার মধ্যে উত্তর দেবে
পার্ট নম্বর উৎপাদক প্যাকেজ QTY লক্ষ্যমূল্য প্রসারিত
✓
বিল প্রস্তুত করা হয়েছে!

আমরা ২৪ ঘণ্টার মধ্যে আপনার ইমেইলে প্রত্যুত্তর দেব

1
RFQ জমা হয়েছে
2
কোটেশন পাওয়া গেছে
3
অর্ডার দেওয়া হয়েছে
4
পেমেন্ট
5
শিপ করা হয়েছে
6
ডেলিভারি হয়েছে
RFQ বিবরণ দেখুন