MAX362EPE - 4-Channel 85Ω SPST Analog Switch | Maxim
N.º de pieza: MAX362EPE ✗ Fin de vidaMAX362EPE Descripción general
An analog switch is a semiconductor device that connects or disconnects an analog signal path under digital control. The SPST architecture provides one selectable path for each circuit, while the quad configuration integrates four independent switches into one package. Within the signal-path hierarchy, MAX362EPE belongs to the analog switch and multiplexing category, where low on resistance, predictable channel behavior, and control-signal compatibility are central design considerations.
The MAX362EPE differentiates itself through its four normally open switch functions and listed 85 Ω on resistance. Its 1:1 configuration preserves signal polarity rather than inverting the selected path. The device is listed in an industrial temperature grade and uses a rectangular PDIP-16 package. Four independent control inputs allow a microcontroller or logic circuit to route separate analog nodes without requiring a separate single-channel package for each function.
The MAX361 and MAX362 share the same precision quad-SPST family, but their default contact states differ. MAX362 uses normally open switches, which leave each channel disconnected until the corresponding control signal asserts the connection. This behavior is useful when signal isolation during reset or power-up is required. Exact voltage ratings, leakage currents, channel-to-channel resistance matching, switching-time limits, and absolute maximum conditions should be confirmed in the manufacturer datasheet before a new design is released.
Typical uses include multiplexed sensor acquisition, instrumentation signal routing, test-equipment input selection, industrial control interfaces, and precision analog measurement systems. In these applications, the four switch channels can reduce the number of discrete relays or routing components while allowing software-controlled path selection. Engineers must still check the signal amplitude, bandwidth, leakage, and control-logic thresholds against the complete operating specification.
A practical design consideration is to route each analog trace away from fast digital or switching-regulator nodes, and to place any protection or filtering components close to the connector or source. Because the MAX362EPE uses normally open contacts, system startup and fault-response logic should account for the unasserted state. Confirm the complete pin mapping and control polarity against the manufacturer datasheet before laying out a board.
This product page consolidates the exact MPN identity, package information, lifecycle information, commercial ordering path, and available drop-in comparison for the obsolete MAX362EPE. It also adds practical guidance on analog-signal integrity, default switch state, control sequencing, and the checks required when replacing legacy through-hole analog switches.
Alternativas directas para MAX362EPE — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con MAX362EPE (mismo factor de forma y huella) — difiere en Package, Temperature Grade.
MAX362CPE+
✅ Sustitución directaConsulte el precio
Ver hoja de datos →MAX362EPE Valores máximos y características eléctricas
| Number of Circuits | 4 circuits |
| Switch Type | Single-pole single-throw (SPST) |
| Default Contact State | Normally open (NO) |
| Channel-to-Channel Ratio | 1:1 |
| On Resistance | 85 ohm |
| Technology | CMOS |
| Encapsulado | 16-pin PDIP |
| Package Type | PDIP-16 through-hole |
| Package Shape | Rectangular |
| Surface Mount | No |
| Temperature Grade | Industrial |
| Number of Terminals | 16 terminals |
Guía de configuración de pines de MAX362EPE rectangular
Configuración de pines para MAX362EPE (encapsulado rectangular). La numeración de pines, las funciones y los diagramas de conexión se definen en la hoja de datos del fabricante. Consúltela para conocer el footprint exacto y las directrices de soldadura.
No hay datos detallados de patillaje disponibles para MAX362EPE.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
MAX362EPE es adecuado para 6 aplicacións: Multiplexed Sensor Acquisition, Precision Test and Measurement, Industrial Control Signal Routing, Communication and Data Acquisition, Audio and Measurement Path Selection, Legacy Peripheral Signal Multiplexing.
Multiplexed Sensor Acquisition
The MAX362EPE can route four sensor signals through a shared analog front end while its normally open contacts keep each channel isolated until explicitly enabled. The listed 85 Ω on resistance provides a defined series impedance for the selected path, while four independent control inputs simplify microcontroller-controlled channel selection. This arrangement is useful in industrial monitoring systems that must scan temperature, pressure, and level transducers through one measurement chain. Before implementation, verify that the sensor excitation range, source impedance, leakage, and settling time remain acceptable after the switch and its surrounding acquisition circuitry are included.
Recomendado
Precision Test and Measurement
MAX362EPE fits instrument front ends that must select among several analog inputs without using a separate switch package for every channel. Its four 1:1 SPST paths preserve signal polarity, while the normally open state provides a defined disconnected condition before measurement begins. The 85 Ω on resistance is relevant when calculating source impedance, attenuation, and amplifier-input interactions. Engineers should confirm the complete signal bandwidth, charge injection, off leakage, and switching-time specifications against the highest expected source impedance and shortest required measurement interval.
Recomendado
Industrial Control Signal Routing
The MAX362EPE can provide software-controlled selection of four industrial analog command or feedback paths when the controller requires independent, isolated connections. Its normally open switch behavior supports fail-safe logic if the control firmware leaves every channel deasserted during initialization or fault handling. The 16-pin PDIP package is appropriate for through-hole legacy and industrial-control boards. Design review should cover the maximum switched voltage, control thresholds, surge exposure, and the effect of the 85 Ω path resistance on actuator or feedback-network calculations.
Recomendado
Communication and Data Acquisition
The MAX362EPE is suitable for older communication equipment that uses four switched analog branches feeding a shared converter or transceiver path. Independent control inputs permit channel selection from digital logic, while the 1:1 configuration avoids signal inversion. Its 85 Ω on resistance contributes to the total source impedance seen by the receiving circuit and must be included in gain and bandwidth analysis. Because this is a legacy through-hole device, maintainers should also check system-level grounding, connector transients, and nearby switching-supply noise before reusing the existing board architecture.
Recomendado
Audio and Measurement Path Selection
MAX362EPE can select among four low-level analog sources in measurement equipment when each source must remain disconnected until selected. The normally open contacts prevent unintended signal paths from loading shared circuitry during setup, while the 85 Ω on resistance must be included in the source-impedance and noise analysis. The device is most appropriate for controlled, legacy-style signal routing rather than high-bandwidth audio multiplexing. Confirm off-state isolation, channel matching, maximum input amplitude, and control-signal behavior in the manufacturer datasheet before finalizing the audio-path topology.
Recomendado
Legacy Peripheral Signal Multiplexing
The MAX362EPE offers a compact through-hole way to multiplex four peripheral signals in legacy embedded systems. Its quad arrangement reduces the number of separate single-switch packages, and independent control inputs can be driven from a microcontroller or latch. The normally open topology can simplify reset-state behavior by leaving external lines disconnected until the system has completed initialization. Validate voltage levels, source impedance, leakage into adjacent circuits, and switching transients against the original system requirements, particularly when modern low-power peripherals are connected to the same analog node.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para MAX362EPE — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | MAX362CPE+ |
|---|---|---|
| Package | PDIP-16 | PDIP-16 |
| Brand | Maxim Integrated | Maxim Integrated |
| Number of Circuits | 4 circuits | 4 circuits |
| Switch Type | Single-pole single-throw (SPST) | Single-pole single-throw (SPST) |
| Default Contact State | Normally open | Normally open |
| On Resistance | 85 ohm | 85 ohm |
| Channel-to-Channel Ratio | 1:1 | 1:1 |
| Temperature Grade | Industrial | Commercial |
| Mounting Type | Through-hole | Through-hole |
Diferenciadores clave
- Four independent normally open analog paths (frente a MAX362CPE+)
- Industrial-grade temperature classification (frente a MAX362CPE+)
- Established through-hole footprint (frente a MAX362CPE+)
Notas de diseño
Keep each switched analog path short and place any termination, filtering, or clamping components close to the signal source or connector. Treat the 85 Ω on resistance as part of the complete source impedance seen by the next amplifier or converter. Avoid routing sensitive nodes beside digital control lines, clock outputs, and high-current switching paths, because capacitive coupling through the control and power pins can create errors even when the switch is in its open state.
Define the power-up and reset behavior explicitly because all four MAX362EPE channels are normally open. Pull control inputs to a defined inactive state if the supervising controller can tri-state or reset unexpectedly, and avoid floating control inputs. Confirm the device’s supply range, control thresholds, and quiescent behavior from the manufacturer datasheet, then calculate the supply current required by the surrounding system before assigning the analog and digital ground connections.
Do not assume that a 16-pin PDIP replacement is interchangeable solely because its outline matches. MAX362CPE+ retains the listed 85 Ω, four-channel normally open SPST configuration, but its commercial temperature grade differs from the MAX362EPE industrial grade. Confirm minimum and maximum ambient temperature, control polarity, pin names, electrical limits, and obsolete-part availability before approving it as a drop-in substitute.
Información de cumplimiento
No specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals statement was identified for the exact MAX362EPE ordering code. AEC-Q100 is not applicable because this is an industrial analog interface switch rather than an automotive-qualified device.