Maxim Integrated

MAX379CPE+ - Fault-Protected 4:1 Multiplexer | Maxim Integrated

MPN: MAX379CPE+ ✓ সক্রিয়
Fault-protected Vdss A few nA Id 3.5 kOhm Rds(on) 16-pin PDIP Package
সর্বনিম্ন অর্ডার পরিমাণ: 1 |

MAX379CPE+ সারাংশ

The Maxim Integrated MAX379CPE+ is a high-voltage, fault-protected analog multiplexer with two 4:1 switches, a 3.5 kOhm on-resistance, and a 16-pin PDIP package. It is a differential 2-of-8 multiplexer, allowing eight source inputs to be organized into four selectable differential pairs for measurement, routing, and instrumentation systems.

A multiplexer is an analog switch network that routes one of several signal sources to a common output. The MAX379 belongs to the broader analog switch and multiplexer hierarchy within interface ICs. Its differential architecture is intended for paired signals, while its 4:1 configuration provides four selections per switch. The series N-channel, P-channel, and N-channel structure is specifically designed to improve protection when the device supplies are off but external input voltages remain present.

The key features of the MAX379CPE+ include its fault-tolerant input structure, two independent 4:1 circuits, and 3.5 kOhm switch resistance. Differential routing reduces the influence of common-mode effects when paired signals are measured together. The high-voltage, fault-protected design is useful when transient or powered-off conditions could otherwise stress the input network. Two circuits in one package also reduce board area compared with separate single-ended or differential switch assemblies.

Technically, the MAX379 is described as an 8-channel, high-voltage, fault-protected multiplexer. The manufacturer identifies the MAX379 as a four-channel differential, 2-of-8 multiplexer, while the MAX378 in the same family is an eight-channel single-ended, 1-of-8 device. During an unintended power-off condition, the MAX379 channels turn off and the input current falls to only a few nanoamperes. This behavior helps isolate applied signals from the internal switching path when supply power is absent.

Typical uses include automated test equipment, data-acquisition systems, battery or power-system monitoring, industrial control interfaces, and laboratory measurement equipment. The differential configuration is especially appropriate for bridge sensors, paired analog channels, and systems where a common measurement reference is required.

PCB layout should preserve the pin assignments of the 16-pin PDIP package and route high-impedance analog nodes with short, guarded traces. Check signal amplitude and fault conditions against the manufacturer operating limits before connecting external sources. Because this is a through-hole package, component height, lead spacing, and connector orientation also require mechanical validation.

This product page combines the manufacturer function description, exact distributor package and resistance information, lifecycle context, and practical guidance for selecting, sourcing, and implementing the MAX379CPE+ in analog-routing systems.

এর জন্য ড্রপ-ইন বিকল্প MAX379CPE+ — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।

MAX379CPE

✅ ড্রপ-ইন
📦 16-pin PDIP
Same 4:1 topology, 3.5 kOhm resistance, and 16-pin PDIP package; disclosed functional difference is 0%

📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)

MAX379EPE

✅ ড্রপ-ইন ⚠️ স্পেক যাচাইকৃত নয়
📦 16-pin PDIP
Same 4:1 topology, 3.5 kOhm resistance, and 16-pin PDIP package; disclosed functional difference is 0%

📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)

MAX379EPE+

✅ ড্রপ-ইন ⚠️ স্পেক যাচাইকৃত নয়
📦 16-pin PDIP
Same 4:1 topology, 3.5 kOhm resistance, and 16-pin PDIP package; disclosed functional difference is 0%

📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)

DG412CUE+

✅ ড্রপ-ইন
📦 16-pin PDIP
Same dual 4:1 routing and 16-pin PDIP package; published MAX379CPE comparison identifies it as a complete replacement, while on-resistance differs by 0.3 kOhm at the stated 3.5 kOhm versus 3.8 kOhm level

📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)

MAX328EPE

✅ ড্রপ-ইন
📦 16-pin PDIP
Same dual 4:1 routing and 16-pin PDIP package identified in the comparison; disclosed functional difference is 0% for the common switch function

📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)

MAX379CPE+ বিশেষণ

Multiplexer Configuration 2 circuit, 4:1 switch
Channel Arrangement 8 channels, 4-channel differential 2-of-8
On Resistance 3.5 kOhm
Input Protection Structure Series N-channel, P-channel, N-channel
Off-State Input Current A few nA
Package Type 16-pin PDIP
Package Shape Rectangular
Mounting Method Through-hole, non-surface-mount
Number of Terminals 16
Temperature Grade Commercial
Number of Circuits 2
Switch Type SP4T
High-Voltage Protection Fault-protected
Production Status Production

MAX379CPE+ rectangular পিন কনফিগারেশন গাইড

MAX379CPE+ (rectangular প্যাকেজ)-এর পিন কনফিগারেশন। পিন নম্বরিং, ফাংশন এবং সংযোগ ডায়াগ্রাম প্রস্তুতকারকের ডেটাশিটে সংজ্ঞায়িত করা আছে। সঠিক ফুটপ্রিন্ট এবং সোল্ডারিং নির্দেশিকার জন্য এটি দেখুন।

MAX379CPE+-এর জন্য rectangular প্যাকেজ পিনআউট ডায়াগ্রাম

এর জন্য বিস্তারিত পিনআউট ডেটা পাওয়া যায়নি MAX379CPE+.

দেখুন ডেটাশিট সম্পূর্ণ পিন কনফিগারেশনের জন্য।

সাধারণ ব্যবহার

MAX379CPE+ এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Automated Test Equipment Signal Routing, Bridge Sensor Data Acquisition, Industrial Control Signal Multiplexing, Battery Monitoring Systems, Laboratory Measurement Systems, Data Acquisition Interface Cards.

⚡

Automated Test Equipment Signal Routing

The MAX379CPE+ suits automated test equipment that must route several paired measurement channels into shared instrumentation. Its two 4:1 switch circuits provide four differential selections while occupying one 16-pin PDIP package, reducing the number of separate switch assemblies on a through-hole test fixture. The 3.5 kOhm on-resistance must be included in the measurement uncertainty budget, particularly for high-impedance sensors. The manufacturer’s fault-protected series N-channel/P-channel/N-channel structure is valuable when a fixture or external source can remain energized during a system power-down.

🧩

Bridge Sensor Data Acquisition

The MAX379CPE+ is appropriate for bridge-sensor and other paired-signal data-acquisition systems because it routes four differential selections across two internal switch circuits. Differential selection helps keep excitation and sensing paths paired when the measurement front end compares a sensor signal against a reference. Its 3.5 kOhm on-resistance can affect source loading, so the input impedance and acquisition timing should be calculated together. If the sensor wiring can experience voltage during equipment shutdown, the MAX379 fault-protected architecture adds useful isolation compared with an unprotected analog switch.

🏭

Industrial Control Signal Multiplexing

The MAX379CPE+ can reduce analog routing complexity in industrial controllers that must select among multiple paired process signals. Two 4:1 circuits share one package, allowing controller boards to route four differential channel groups without using separate switch packages. Its fault-protected structure is useful when external field wiring remains connected while control electronics are unpowered. The commercial-grade PDIP package is mechanically convenient for through-hole industrial assemblies, although the selected MAX379 suffix and its temperature rating must satisfy the enclosure’s environmental requirements.

⚡

Battery Monitoring Systems

The MAX379CPE+ can be used in battery and power-system monitoring equipment where several voltage pairs must be presented to one measurement channel. The two independent 4:1 circuits permit organized routing of paired battery-cell or rail voltages, while the high-voltage fault-protection characteristic helps manage unusual field conditions. Designers should verify the applicable signal and supply limits in the manufacturer operating table and account for the 3.5 kOhm path resistance when the monitored source has meaningful impedance. The package also allows a straightforward retrofit to existing through-hole monitoring designs.

🔧

Laboratory Measurement Systems

The MAX379CPE+ is useful in laboratory instruments that require repeatable selection among paired analog inputs. Its differential organization helps maintain symmetry between the active and reference paths, while the dual 4:1 arrangement expands a single measurement channel into eight selectable inputs. The 3.5 kOhm switch resistance should be included in precision calculations and may require high-impedance buffers when signal attenuation is critical. Its fault-protected structure also improves robustness in instrument systems where test leads can remain attached during shutdown or range changes.

🖥️

Data Acquisition Interface Cards

The MAX379CPE+ can expand a legacy data-acquisition interface by selecting multiple differential channel groups through a single 16-pin PDIP device. Two 4:1 circuits provide four differential routes, which is helpful when amplifier stages, isolation amplifiers, or converters require channel selection rather than simultaneous sampling. Because the device is a multiplexer, the selected signals are routed sequentially rather than sampled concurrently. The 3.5 kOhm on-resistance, acquisition-settling time, and source impedance determine practical accuracy, so the complete analog chain must be validated at the required sampling rate.

সুপারিশকৃত পণ্যের সারসংক্ষেপ

MAX379CPE+ Maxim Integrated ব্যবহৃত হয়: Automated Test Equipment Signal Routing, Bridge Sensor Data Acquisition, Industrial Control Signal Multiplexing, Battery Monitoring Systems, Laboratory Measurement Systems, Data Acquisition Interface Cards MAX379CPE Same-family PDIP routing device ব্যবহৃত হয়: Automated Test Equipment Signal Routing, Industrial Control Signal Multiplexing, Battery Monitoring Systems MAX378CPE Single-ended companion multiplexer ব্যবহৃত হয়: Automated Test Equipment Signal Routing, Bridge Sensor Data Acquisition, Laboratory Measurement Systems MAX379EPE+ Same-family alternative configuration ব্যবহৃত হয়: Bridge Sensor Data Acquisition DG412CUE+ Dual 4:1 PDIP switching alternative ব্যবহৃত হয়: Industrial Control Signal Multiplexing, Data Acquisition Interface Cards MAX328EPE Dual 4:1 routing option ব্যবহৃত হয়: Battery Monitoring Systems, Data Acquisition Interface Cards MAX379EPE Same-family alternative ব্যবহৃত হয়: Laboratory Measurement Systems
What is the MAX379CPE+ used for?
The MAX379CPE+ is a high-voltage, fault-protected analog multiplexer used to route differential measurement signals. It contains two 4:1 switches and is described by the manufacturer as an eight-channel, four-channel differential 2-of-8 multiplexer. According to the manufacturer datasheet for the MAX379 family, its series N-channel/P-channel/N-channel structure limits fault current when external inputs remain energized while the device supplies are off.
How many channels and switches does MAX379CPE+ have?
The MAX379CPE+ provides eight multiplexed channels organized as four differential pairs and contains two independent 4:1 switch circuits. The manufacturer describes the MAX379 as a four-channel differential, 2-of-8 multiplexer. A distributor listing for the exact MAX379CPE+ part identifies it as a two-circuit IC switch with a 4:1 configuration and 3.5 kOhm on-resistance.
What is the on-resistance of MAX379CPE+?
The MAX379CPE+ has a specified on-resistance of 3.5 kOhm. This value describes the resistance of each selected analog path when the switch is conducting. According to the exact-part DigiKey listing, the MAX379CPE+ is a two-circuit, 4:1 analog switch with 3.5 kOhm resistance. For precision measurements, include this resistance in the complete signal-path error budget.
Why is the MAX379 described as fault-protected?
The MAX379 is fault-protected because its series N-channel/P-channel/N-channel structure controls current when external signals are applied while the device is not powered. According to the manufacturer product page, all channels turn off under that condition and input current falls to only a few nanoamperes. The architecture helps protect the multiplexer from inadvertent input voltages that could otherwise exceed its normal operating state.
What is the difference between MAX379 and MAX378?
The MAX379 is a four-channel differential 2-of-8 multiplexer, whereas the MAX378 is an eight-channel single-ended 1-of-8 multiplexer. The manufacturer describes both parts as high-voltage, fault-protected devices using the same series N-channel/P-channel/N-channel protection approach. Choose MAX379 for paired or differential signals and MAX378 when eight independent single-ended channels are required.
Where can I download the MAX379CPE+ datasheet PDF?
The official MAX379 datasheet and product resources are available on the Analog Devices product page for MAX379. That page links the manufacturer data sheet, product selection table, documentation, and lifecycle information for the MAX379 family. It is the preferred source for electrical characteristics, the pin-description table, operating limits, and the exact ordering information associated with MAX379CPE+.
Where is the MAX379CPE+ pinout located?
The MAX379CPE+ pinout is documented in the pin-description table of the manufacturer MAX379 datasheet. The exact MAX379CPE+ ordering code uses a 16-pin PDIP package. Use the manufacturer pin table and package drawing to assign enable, select, common, input, output, and supply connections because the complete pin names are not reproduced on this product page.
Is MAX379CPE+ in stock and how long is the lead time?
The manufacturer lists the MAX379 family in production, while distributor inventory and lead time can change by order quantity. Request current stock, minimum order quantity, and lead time through the Request a Quote form on this page. The form provides a direct quotation channel without requiring reliance on outdated inventory claims.
What is the price of MAX379CPE+?
Current pricing for the MAX379CPE+ should be obtained through the Request a Quote form on this page because commercial pricing and availability are time-sensitive. Quote requests can confirm the exact MAX379CPE+ suffix, 16-pin PDIP package, order quantity, and delivery requirements. No fixed price should be inferred from general MAX379 family list-price information.
Can I buy MAX379CPE+ online?
The MAX379CPE+ can be requested for quotation through the Request a Quote form on this page. State the required quantity and delivery destination so the exact ordering code, package, current availability, and lead time can be confirmed. Because this is an active Maxim Integrated production part, quotation is preferable to relying on historical inventory information.
What can replace MAX379CPE+?
A drop-in replacement must use the same 16-pin PDIP footprint, preserve the 4:1 routing arrangement, and provide compatible differential-channel behavior and voltage limits. MAX379CPE, MAX379EPE, and MAX379EPE+ are same-family candidates, while DG412CUE+ is identified as a complete replacement in a public comparison. Confirm the manufacturer pin table and operating limits before approving any substitute.
Is DG412CUE+ the same as MAX379CPE+?
DG412CUE+ is presented as a complete replacement for MAX379CPE in a public part comparison, with both devices described as dual 4:1 multiplexers in 16-pin PDIP packages. The replacement still requires an engineering review of signal polarity, enable logic, channel mapping, voltage ratings, and fault behavior. Treat the cross-reference as a starting point and compare the two manufacturer datasheets before production use.
When should I choose MAX379CPE+ over a generic 4:1 analog switch?
Choose the MAX379CPE+ when the design needs paired differential signals, two 4:1 switches in one package, and protection against external input voltages applied while the device is unpowered. A generic 4:1 switch may be adequate for ordinary low-voltage routing, but it may not reproduce the MAX379 channel arrangement or series N-channel/P-channel/N-channel fault-protection structure. The 16-pin PDIP package also favors through-hole and legacy industrial designs.
Is the MAX379CPE+ suitable for high-voltage instrumentation?
The MAX379CPE+ is specifically described as an 8-channel, high-voltage, fault-protected multiplexer and is suitable for instrumentation designs that need differential selection and fault-current limitation. The exact maximum signal and supply voltages must be taken from the manufacturer operating table before connection. High voltage in this context denotes the device family’s protection characteristics, not permission to exceed its specified ratings.
What are the key specifications of MAX379CPE+ engineers should know?
The essential MAX379CPE+ specifications are its two 4:1 switch circuits, eight-channel differential 2-of-8 organization, 3.5 kOhm on-resistance, 16-pin PDIP package, and high-voltage fault-protected input architecture. The exact-part DigiKey listing confirms the two-circuit 4:1 configuration, resistance, and package. According to the manufacturer datasheet, the series N-channel/P-channel/N-channel structure limits current to only a few nanoamperes when inputs remain applied while the supplies are off.

এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা MAX379CPE+ — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।

নির্বাচন গাইড

Choose the MAX379CPE+ when the design needs two 4:1 switches, four differential selections, a 3.5 kOhm on-resistance, and the MAX379 family’s fault-protected input architecture in a 16-pin PDIP package. It is particularly suitable for paired instrumentation signals, test systems, and equipment where external inputs may remain energized during shutdown. MAX379CPE, MAX379EPE, and MAX379EPE+ are same-family candidates when lifecycle or temperature-grade requirements differ, although each ordering suffix must be checked. Consider DG412CUE+ for a cross-brand dual 4:1 PDIP implementation, but its stated 3.8 kOhm resistance is 0.3 kOhm higher and its fault-protection behavior must be compared directly. Avoid choosing solely from package count: channel mapping, common connections, enable polarity, signal polarity, absolute-maximum ratings, and settling behavior determine whether a device is truly interchangeable.

বিকল্পের সাথে তুলনা

পারামিটার এই পণ্য MAX379CPE MAX379EPE MAX379EPE+ DG412CUE+ MAX328EPE
Package 16-pin PDIP 16-pin PDIP 16-pin PDIP 16-pin PDIP 16-pin PDIP 16-pin PDIP
Brand Maxim Integrated Maxim Integrated Maxim Integrated Maxim Integrated Microchip Technology Maxim Integrated
Switch Configuration Dual 4:1 Dual 4:1 Dual 4:1 Dual 4:1 Dual 4:1 Dual 4:1
Number of Circuits 2 2 2 2 2 2

মূল পার্থক্যসমূহ

  • Two 4:1 circuits support four differential selections (বনামMAX378CPE)
  • Lower on-resistance than the identified DG412CUE+ replacement (বনামDG412CUE+)
  • Explicit series N-channel/P-channel/N-channel fault-protection structure (বনামDG412CUE+)
  • Combines differential multiplexing with a 16-pin PDIP footprint (বনামADG452BRZ)

ডিজাইন নোট

Do not assume generic 4:1 analog-switch behavior is interchangeable with the MAX379. The MAX379 is organized as a four-channel differential 2-of-8 multiplexer with two 4:1 circuits, and its protection behavior depends on the series N-channel/P-channel/N-channel structure. Before substituting another 16-pin PDIP device, compare channel mapping, common-pin connections, enable polarity, signal polarity, supply requirements, and maximum operating voltages against the manufacturer pin and operating tables.

Route the analog inputs, outputs, common connections, and select-control traces as short as practical, with high-impedance nodes surrounded by grounded guard traces where supported by the circuit layout. Keep the 16-pin PDIP footprint and connector orientation unchanged so the component can be replaced without PCB changes. Because the package is through-hole rather than surface-mount, also verify lead pitch, drilled diameter, body clearance, and component height against the enclosure or connector mechanical drawing.

Include the 3.5 kOhm on-resistance in the acquisition error budget and check settling time against the signal source impedance and required measurement bandwidth. A higher-impedance sensor can produce a larger attenuation error than the switch resistance alone would suggest. For differential channels, preserve symmetry between paired routing paths and place any input buffers close enough to the multiplexer that leakage, capacitance, and pickup do not dominate the measurement.

The manufacturer states that when the supplies are inadvertently turned off while input voltages remain applied, the MAX379 channels turn off and input current is limited to a few nanoamperes. This fault behavior still depends on correct supply decoupling and a valid power-up sequence. Use the manufacturer’s recommended bypass capacitors, place them adjacent to the supply pins, and avoid allowing uncontrolled external-source energy to exceed the absolute-maximum ratings listed in the datasheet.

কমপ্লায়েন্স তথ্য

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
লিড ফ্রি
Unknown
হ্যালোজেন ফ্রি
Unknown
কনফ্লিক্ট মিনারেলস
Unknown

The manufacturer identifies the MAX379 family as being in production, but no specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals declarations were identified in the product information. The device is not described as an automotive-qualified part.

ডেটা যাচাই করা হয়েছে: 2026-11-14 — ডেটা XAIPART-এর কম্পোনেন্ট ইঞ্জিনিয়ারিং টিম দ্বারা যাচাই ও কিউরেট করা হয়েছে

সম্পর্কিত অনুসন্ধান

MAX379CPE+ datasheet MAX379CPE+ pinout MAX379CPE+ datasheet pdf MAX379CPE+ equivalent MAX379CPE+ replacement MAX379CPE+ cross reference Maxim Integrated MAX379CPE+ MAX379CPE+ vs DG412CUE+ MAX379CPE+ 3.5 kOhm multiplexer MAX379CPE+ 16-pin PDIP MAX379CPE+ price MAX379CPE+ stock MAX379 differential multiplexer application MAX379CPE+ footprint MAX379CPE+ schematic

সম্পর্কিত কম্পোনেন্ট ও শর্তাবলী

Maxim Integrated MAX379CPE+ MAX379CPE MAX379EPE MAX379EPE+ MAX378CPE MAX328EPE DG412CUE+ ADG452BRZ analog multiplexer analog switch differential multiplexer 2-of-8 multiplexer 4:1 switch interface IC fault-protected multiplexer high-voltage analog switch series N-channel/P-channel/N-channel structure on resistance powered-off input current PDIP-16 through-hole package automated test equipment bridge sensor data acquisition industrial control signal routing
তাৎক্ষণিক বিলওয়াছে রেকোজিউইট
সম্পূর্ণ বিবরণ পূরণ করুন — আমাদের সেলস টিম 24 ঘণ্টার মধ্যে উত্তর দেবে
পার্ট নম্বর উৎপাদক প্যাকেজ QTY লক্ষ্যমূল্য প্রসারিত
✓
বিল প্রস্তুত করা হয়েছে!

আমরা ২৪ ঘণ্টার মধ্যে আপনার ইমেইলে প্রত্যুত্তর দেব

1
RFQ জমা হয়েছে
2
কোটেশন পাওয়া গেছে
3
অর্ডার দেওয়া হয়েছে
4
পেমেন্ট
5
শিপ করা হয়েছে
6
ডেলিভারি হয়েছে
RFQ বিবরণ দেখুন