MC33072PG - Dual 44V 4.5MHz Op Amp | onsemi
MPN: MC33072PG ✓ সক্রিয়MC33072PG সারাংশ
An operational amplifier is an analog building block that provides high open-loop gain and uses negative feedback to amplify or process signals. The MC33072 belongs to the hierarchy of operational amplifier, voltage-feedback amplifier, analog signal-processing IC, and semiconductor. Its bipolar construction avoids JFET input devices while providing a practical combination of bandwidth, slew rate, input characteristics, and supply flexibility.
The two amplifier sections offer 5 mV input offset voltage and a nominal 97 dB common-mode rejection ratio. Their 4.5 MHz gain-bandwidth product supports signal bandwidth beyond audio fundamentals, while the 13 V/us slew rate allows relatively rapid transitions. A 3.0 V to 44 V operating range accommodates conventional ±15 V supplies, lower-voltage asymmetric rails, and higher industrial supply arrangements when the circuit and output limits permit.
The MC33072 series uses quality bipolar fabrication and monolithic construction. Each channel can operate as an inverting amplifier, non-inverting amplifier, voltage follower, comparator, or general feedback stage when suitable output swing and stability conditions are respected. Because it is a dual amplifier, both channels share the package supply pins and ground connection, allowing two related signal operations to be implemented in one component.
Typical uses include industrial sensor conditioning, current-loop receivers, audio preamplification, active filters, waveform shaping, and general instrumentation. The 13 V/us slew rate is beneficial for low-amplitude, higher-frequency signals, while the 5 mV offset specification supports accurate closed-loop operation around a stable reference. Its single-supply capability is useful in portable and embedded equipment where generating a negative rail would otherwise add cost and complexity.
Design the circuit around the manufacturer's recommended operating region and ensure the input common-mode range and output swing remain valid at the selected supply voltage. Keep feedback-loop compensation stable, place decoupling capacitors close to the supply pins, and route high-impedance input nodes with short traces and suitable guarding. The 8-pin PDIP package is intended for through-hole assembly and thermal evaluation on the board rather than compact surface-mount designs.
This page combines the manufacturer's MC33072 product information with package characteristics, drop-in alternatives, application guidance, and practical circuit-design notes. It is intended to accelerate component selection while preserving the need to verify operating limits, external circuitry, and PCB-specific requirements before production release.
এর জন্য ড্রপ-ইন বিকল্প MC33072PG — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।
এই সিরিজের ভ্যারিয়েন্ট
একই সিরিজের মডেল যেগুলো drop-in compatible MC33072PG (একই form factor এবং footprint) — পার্থক্য রয়েছে Mounting Type, Slew Rate, Input Offset Voltage, Package, Amplifier Type.
MC34072PG
✅ ড্রপ-ইনমূল্যের জন্য যোগাযোগ করুন
ডেটাশিট দেখুন →MC33072AP
✅ ড্রপ-ইন📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
MC34072AP
✅ ড্রপ-ইন ⚠️ স্পেক যাচাইকৃত নয়📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
TL072CP
✅ ড্রপ-ইনমূল্যের জন্য যোগাযোগ করুন
ডেটাশিট দেখুন →LM072
✅ ড্রপ-ইন📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
MC33072PG সর্বোচ্চ রেটিং ও বৈদ্যুতিক বৈশিষ্ট্য
| Amplifier Type | General-purpose operational amplifier |
| Number of Amplifiers | 2 circuits |
| Architecture | Voltage-feedback dual amplifier |
| Semiconductor Technology | Bipolar |
| Supply Voltage Range | 3.0 V to 44 V |
| Single-Supply Operation | Supported |
| Split-Supply Operation | Supported |
| Gain-Bandwidth Product | 4.5 MHz |
| Slew Rate | 13 V/us |
| Input Offset Voltage | 5 mV maximum |
| Common-Mode Rejection Ratio | 97 dB nominal |
| অপারেটিং তাপমাত্রার পরিসর | -40 C to +85 C |
| প্যাকেজ | 8-PDIP, 0.300 inch (7.62 mm) pitch |
| Packaging | Tube |
| মাউন্টিং টাইপ | Through-hole |
| RoHS স্ট্যাটাস | RoHS-compliant and lead-free |
MC33072PG 8-pdip, 0.300 inch (7.62 mm) pitch পিন কনফিগারেশন গাইড
MC33072PG (8-pdip, 0.300 inch (7.62 mm) pitch প্যাকেজ)-এর পিন কনফিগারেশন। এই অ্যানালগ কম্পোনেন্টে ইনপুট, আউটপুট ও পাওয়ার সাপ্লাই পিন রয়েছে। অফসেট নাল, কম্পেনসেশন ও এনেবল পিন কনফিগারেশনের জন্য প্রস্তুতকারকের ডেটাশিট দেখুন। সিগন্যাল কন্ডিশনিং ও অ্যামপ্লিফায়ার সার্কিটের জন্য আদর্শ।
এর জন্য বিস্তারিত পিনআউট ডেটা পাওয়া যায়নি MC33072PG.
দেখুন ডেটাশিট সম্পূর্ণ পিন কনফিগারেশনের জন্য।
সাধারণ ব্যবহার
MC33072PG এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Industrial Sensor Signal Conditioning, Audio Preamplification, Current-Loop Signal Conditioning, Waveform Shaping and Filtering, Precision Control and Measurement, Portable Instrumentation.
Industrial Sensor Signal Conditioning
The MC33072PG fits industrial sensor-conditioning circuits that need two amplifiers in one 8-PDIP package. Its 4.5 MHz gain-bandwidth product and 13 V/us slew rate preserve signal fidelity for moderately fast sensor outputs, while the 5 mV maximum input offset voltage and 97 dB nominal CMRR support accurate amplification of low-level signals. The two channels can implement a differential input stage followed by a gain or filter stage, reducing external component count. The 3.0 V to 44 V supply range accommodates industrial rails, although the common-mode and output-swing limits must be checked at every operating point.
সুপারিশকৃত
Audio Preamplification
The MC33072PG is suitable for small audio preamplifier and active-filter stages where a dual amplifier provides economy and compactness. Its 13 V/us slew rate is substantially higher than the slew rate required by many low-frequency audio signals, providing margin for larger transient signals, while the 4.5 MHz gain-bandwidth product extends beyond the principal audio band. The bipolar architecture avoids the need for a JFET input stage. Designers should still verify input bias current, output swing, channel matching, and distortion at the selected gain and supply voltage before production.
সুপারিশকৃত
Current-Loop Signal Conditioning
The MC33072PG can support current-loop receivers and industrial transmitter interfaces requiring dual active filtering and amplification. Its 97 dB nominal common-mode rejection ratio helps reject differential noise present on shared measurement lines, while the 5 mV maximum input offset voltage supports low-level loop-voltage accuracy. The 4.5 MHz gain-bandwidth product permits closed-loop filters above the main measurement bandwidth, and the 13 V/us slew rate improves transient response. Supply the device from a rail compatible with the loop voltage and check input common-mode range carefully at the highest and lowest sensor outputs.
সুপারিশকৃত
Waveform Shaping and Filtering
The MC33072PG is useful in waveform-shaping, active-filter, and pulse-processing circuits where the 4.5 MHz gain-bandwidth product and 13 V/us slew rate provide useful bandwidth for low-amplitude signals. Its two channels can create complementary active stages or independent filter sections, reducing board area compared with separate single amplifiers. Because bipolar input devices draw bias current, source impedance and feedback-resistor values must be selected to control offset and bias-current errors. Validate the closed-loop response, output swing, and stability with the external component values planned for production.
সুপারিশকৃত
Precision Control and Measurement
The MC33072PG can be used in control and measurement circuits where two related analog channels amplify a sensed variable and buffer its reference. Its 5 mV maximum input offset voltage and nominal 97 dB CMRR support accurate operation around a low-level reference, while the 4.5 MHz bandwidth and 13 V/us slew rate accommodate practical control-loop dynamics. The 3.0 V to 44 V operating range supports operation from low-voltage systems through conventional bipolar-style rails. Compensation networks, grounding, and supply bypassing should be designed around the actual feedback topology and verified for noise, settling, and output-load behavior.
সুপারিশকৃত
Portable Instrumentation
The MC33072PG is suitable for portable instrumentation designed around a single positive supply. Starting operation at 3.0 V helps support compact systems, and the dual configuration can implement gain and filtering stages in one through-hole package. The 4.5 MHz gain-bandwidth product is adequate for many low-level measurement and control paths, while the 13 V/us slew rate reduces output-transition constraints. Single-supply designs normally require an input reference near mid-supply and careful attention to input and output ranges. Minimize power-supply noise, maintain a low-impedance reference, and confirm offset behavior across the intended temperature range.
সুপারিশকৃত
সুপারিশকৃত পণ্যের সারসংক্ষেপ
এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা MC33072PG — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।
নির্বাচন গাইড
বিকল্পের সাথে তুলনা
| পারামিটার | এই পণ্য | MC34072PG | MC33072AP | MC34072AP | TL072 | LM072 |
|---|---|---|---|---|---|---|
| Package | 8-PDIP (0.300 inch, 7.62 mm pitch) | 8-PDIP (0.300 inch, 7.62 mm pitch) | 8-PDIP (0.300 inch, 7.62 mm pitch) | 8-PDIP (0.300 inch, 7.62 mm pitch) | 8-PDIP (0.300 inch, 7.62 mm pitch) | 8-PDIP (0.300 inch, 7.62 mm pitch) |
| Brand | onsemi | onsemi | onsemi | onsemi | Texas Instruments | Texas Instruments |
| Amplifier Count | 2 circuits | 2 circuits | 2 circuits | 2 circuits | 2 circuits | 2 circuits |
| Gain-Bandwidth Product | 4.5 MHz | 4.5 MHz | 4.5 MHz | 4.5 MHz | Approximately 3 MHz | Approximately 3 MHz |
| Technology | Bipolar | Bipolar | Bipolar | Bipolar | Bipolar | Bipolar |
মূল পার্থক্যসমূহ
- Higher gain-bandwidth product than the TL072 cross-reference family (বনামTL072)
- Higher gain-bandwidth product than the LM072 cross-reference family (বনামLM072)
- Wide 3.0 V to 44 V supply operating range (বনামMC34072PG)
ডিজাইন নোট
Place the supply-decoupling capacitors close to the MC33072PG supply pins and connect them to a low-impedance ground plane. Keep the feedback components close to the relevant amplifier pins, and minimize the distance from high-impedance input nodes to the IC. In single-supply circuits, route the mid-supply reference through a quiet divider or buffered reference stage and avoid sharing that trace with output-load currents.
Do not assume that a nominal 44 V supply rating means the amplifier can process a 44 V input signal. The input common-mode range and output swing remain separate constraints, and the valid limits depend on the supply arrangement. Confirm both channels against the actual minimum and maximum signal values, including transient overshoot, before applying the device to high-voltage instrumentation.
Bipolar input bias current can create offset errors when source impedance is high. Keep source impedances balanced where channel matching matters and avoid excessive feedback-resistor values. For fast or low-amplitude stages, use short feedback paths, appropriate bandwidth compensation, and an output isolation resistor when capacitive loading requires it. Evaluate settling and ringing on a prototype rather than relying only on nominal bandwidth.
কমপ্লায়েন্স তথ্য
The product-page information identifies MC33072PG as RoHS-compliant and lead-free. No specific REACH, halogen-free, conflict-minerals, or automotive qualification statement was established for this exact ordering code.