onsemi

MC33074AP - 44V Quad Op Amp, 4.5MHz, 14-DIP | onsemi

MPN: MC33074AP ✓ সক্রিয়
3.0V to 44V Vdss 14-pin plastic DIP Package
সর্বনিম্ন অর্ডার পরিমাণ: 1 |

MC33074AP সারাংশ

onsemi MC33074AP is a quad general-purpose operational amplifier with four single-ended amplifiers in a 14-pin plastic DIP package. It supports single-supply operation from 3.0V to 44V and provides 4.5MHz gain-bandwidth product, 13V/us slew rate, and 3mV input offset voltage. The four amplifiers are designed for broad industrial, instrumentation, signal-conditioning, and control applications requiring economical precision.

An operational amplifier, or op amp, is a high-gain differential amplifier whose open-loop behavior is shaped by external feedback. The MC33074AP belongs to the bipolar operational-amplifier family within the broader amplifier IC and analog semiconductor hierarchy. Each of its four channels can operate from a common positive supply and ground while supporting applications that involve signal amplification, buffering, comparisons, summing, and feedback-controlled analog circuits.

The MC33074AP combines a 4.5MHz gain-bandwidth product with a 13V/us slew rate, allowing useful bandwidth beyond audio frequencies and rapid output transitions in transient signals. Its 3mV input offset voltage provides a defined level of input imbalance that must be included in precision-chain error budgets. The 3.0V to 44V supply range covers low-voltage circuits, conventional ±15V industrial systems, and higher single-supply rails. The monolithic quad construction reduces the number of separate amplifier packages required on a board.

The bipolar internal design avoids the input-bias-current behavior associated with JFET-input amplifiers. This makes the MC33074AP appropriate for general-purpose signal conditioning where input bias current, offset voltage, slew rate, and supply range are the principal selection criteria. Because four amplifiers share one package, thermal behavior, supply decoupling, unused-channel handling, and channel-to-channel matching should be considered together rather than treating each section as an isolated component.

Typical uses include industrial sensor interfaces, low-level control-signal amplification, audio preamplification, active filtering, waveform conditioning, and four-channel monitoring systems. The 44V maximum supply also provides headroom for systems with elevated rail voltages, although the complete circuit must remain within the absolute maximum ratings of every connected device. Grounded-source sensors, transducers, and analog front ends can benefit from the channel count and common package organization.

For a new design, confirm the 14-pin DIP footprint and verify every pin function against the manufacturer pin-description table before layout release. Place the power-supply bypass capacitor close to the supply pin, provide a stable ground reference, and avoid leaving unused op-amp inputs floating. Confirm output swing, common-mode range, stability with the intended feedback network, and required noise performance at the actual supply voltage and signal frequency.

This product page combines the manufacturer device information with practical supply, layout, comparison, and selection guidance. It also distinguishes exact package compatibility from merely similar amplifier functions, helping engineers identify replacements that can be considered for a PCB-level substitution and those that require a broader redesign.

এর জন্য ড্রপ-ইন বিকল্প MC33074AP — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।

MC33074APG

✅ ড্রপ-ইন
📦 14-pin plastic DIP
Same MC33074 family and 4.5MHz bandwidth; suffix-level package and temperature details must be confirmed, with no quantified electrical difference established

📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)

MC34074AP

✅ ড্রপ-ইন ⚠️ স্পেক যাচাইকৃত নয়
📦 14-pin plastic DIP
Same onsemi quad DIP package; input offset and other family-level limits differ, with up to 30% parameter variation requiring verification

📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)

MC33074AP সর্বোচ্চ রেটিং ও বৈদ্যুতিক বৈশিষ্ট্য

Number of Amplifiers 4 amplifiers
Amplifier Type Single-ended general-purpose operational amplifier
Supply Voltage Range 3.0V to 44V
Gain-Bandwidth Product 4.5MHz
Slew Rate 13V/us
Input Offset Voltage 3mV
Internal Transistor Technology Bipolar
প্যাকেজ 14-pin plastic DIP
মাউন্টিং টাইপ Through-hole
Number of Channels 4

MC33074AP 14-pin plastic dip পিন কনফিগারেশন গাইড

MC33074AP (14-pin plastic dip প্যাকেজ)-এর পিন কনফিগারেশন। এই অ্যানালগ কম্পোনেন্টে ইনপুট, আউটপুট ও পাওয়ার সাপ্লাই পিন রয়েছে। অফসেট নাল, কম্পেনসেশন ও এনেবল পিন কনফিগারেশনের জন্য প্রস্তুতকারকের ডেটাশিট দেখুন। সিগন্যাল কন্ডিশনিং ও অ্যামপ্লিফায়ার সার্কিটের জন্য আদর্শ।

MC33074AP-এর জন্য 14-pin plastic dip প্যাকেজ পিনআউট ডায়াগ্রাম

এর জন্য বিস্তারিত পিনআউট ডেটা পাওয়া যায়নি MC33074AP.

দেখুন ডেটাশিট সম্পূর্ণ পিন কনফিগারেশনের জন্য।

সাধারণ ব্যবহার

MC33074AP এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Industrial Sensor Signal Conditioning, Active Audio Preamplification, Precision Filter and Integrator Design, Quad-Channel Control Monitoring, Data Acquisition Front End, General Instrumentation Buffering.

🏭

Industrial Sensor Signal Conditioning

The MC33074AP fits four-channel industrial sensor conditioning because it combines four amplifiers in one 14-pin DIP and accepts a 3.0V to 44V supply. Each channel can amplify a low-level transducer signal and establish the gain required by a downstream controller. The 4.5MHz gain-bandwidth product provides more bandwidth than the signal path commonly requires, while 13V/us slew rate allows comparatively rapid response to step changes. Designers should still verify the input common-mode range, output swing, offset error, and source impedance for the selected sensor. The 3mV input offset contributes directly to signal accuracy, particularly when the conditioned output is near the lower end of the controller input range.

🎧

Active Audio Preamplification

The MC33074AP can provide four general-purpose preamplifier channels in audio and communication equipment. Its 4.5MHz gain-bandwidth product covers the audio band with additional bandwidth margin, while the 13V/us slew rate can improve large-signal transient handling compared with slower amplifiers. The 3.0V to 44V supply range permits operation from compact single-supply rails or conventional bipolar-style supplies within the device limits. Four channels in one package simplify the physical design when sources require independent buffering or gain stages. Audio design should account for input offset, output-headroom limits, noise, and the need for an output coupling or biasing solution in single-supply configurations.

🔧

Precision Filter and Integrator Design

The MC33074AP is suitable for active filters, integrators, and closed-loop control blocks because its four bipolar operational amplifiers can form independent active stages. The 4.5MHz gain-bandwidth product gives designers useful open-loop loop gain near the selected signal frequencies, which can improve closed-loop accuracy when the operating frequency remains appropriately below the amplifier bandwidth. A 13V/us slew rate supports signals with finite edge rates. Component tolerances and the amplifier's 3mV input offset can influence DC accuracy, especially in integrators where offset accumulates over time. Stable feedback-network layout and common supply decoupling are essential for repeatable filter behavior.

⚡

Quad-Channel Control Monitoring

A single MC33074AP package can implement four closely related control or monitoring channels where a quad DIP footprint simplifies assembly. Each amplifier can buffer a sensor, comparator-style threshold signal, or error amplifier in a multi-axis system. The 3.0V to 44V operating range accommodates control systems with different rail architectures, while the 4.5MHz bandwidth and 13V/us slew rate support signals beyond slow DC-only operation. All four channels share the same package and supply, so power-distribution design should avoid long traces between the bypass capacitor and the supply pins. Engineers should verify channel-specific output loading, saturation recovery, and any required isolation between command and feedback paths.

🖥️

Data Acquisition Front End

The MC33074AP can serve as the first amplification stage in a multi-channel data-acquisition front end when the source impedance, bandwidth, and accuracy requirements fit its bipolar input characteristics. Its 4.5MHz gain-bandwidth product and 13V/us slew rate provide ample bandwidth for many sensor and control signals, while four channels reduce the number of packages on the board. The 3mV input offset must be included in the overall accuracy calculation, and the common-mode and output-swing limits constrain the usable signal range. Pairing the amplifiers with suitable high-impedance sensors and carefully designed protection can create a practical conditioning stage, but source loading and anti-aliasing requirements must be evaluated independently.

📺

General Instrumentation Buffering

The MC33074AP is appropriate for general instrumentation buffering where four measurement or control signals must be conditioned with a bipolar operational amplifier. Its 4.5MHz gain-bandwidth product supports moderate-bandwidth signals, and the 13V/us slew rate limits large-signal distortion for rapidly changing waveforms. The common 3.0V to 44V supply range simplifies procurement for laboratories, industrial panels, and embedded test equipment that use several rail arrangements. Buffering does not eliminate the need for an input common-mode check: the amplifier must remain within its linear input range, and outputs must not saturate at the selected rail voltage. Stable reference grounding and short feedback paths are essential when preserving low-level measurement accuracy.

What is the MC33074AP?
The MC33074AP is a quad general-purpose bipolar operational amplifier in a 14-pin plastic DIP package. According to the onsemi MC33074 product page, it provides four amplifiers, a 3.0V to 44V supply range, 4.5MHz gain-bandwidth product, and 13V/us slew rate. It is suitable for general industrial signal conditioning, buffering, active filtering, and control applications where one package must provide several amplifier channels.
What is the operating voltage of MC33074AP?
The MC33074AP operates from a 3.0V to 44V common supply, according to the onsemi MC33074 manufacturer product page. This range supports low-voltage single-supply systems as well as conventional split-supply arrangements within the specified limits. Actual circuit performance still depends on output swing, input common-mode range, and thermal conditions at the selected supply voltage.
What are the key specifications of MC33074AP that engineers should know?
The principal MC33074AP specifications are four amplifier channels, a 3.0V to 44V supply range, 4.5MHz gain-bandwidth product, 13V/us slew rate, 3mV input offset voltage, and a 14-pin plastic DIP package. The onsemi product information identifies bipolar fabrication and general-purpose signal conditioning as the core positioning. These figures make the device suitable for industrial instrumentation, active filters, audio paths, and feedback-based control circuits.
Where to download the MC33074AP datasheet PDF?
The MC33074AP datasheet and product documentation are available from the onsemi MC33074 product page at https://www.onsemi.com/products/standard-products/amplifiers-comparators/operational-amplifiers-op-amps/mc33074. Use the manufacturer document for the authoritative pin description, electrical limits, test conditions, typical-performance curves, and ordering information. The 14-pin DIP footprint and four-channel assignment should be confirmed before schematic capture or PCB layout release.
Where can I find the MC33074AP pinout?
The MC33074AP pinout is published in the manufacturer datasheet under the MC33074 family documentation. The device is a 14-pin through-hole DIP containing four operational amplifiers and common power connections. Use the pin-description table rather than inferring connections from another quad amplifier, because pin assignments can differ among 14-pin packages. The complete pin list is not reproduced on this page because individual pin names were not included in the technical listing.
Is MC33074AP suitable for industrial instrumentation?
The MC33074AP is suitable for many industrial instrumentation and control tasks because it combines a 4.5MHz gain-bandwidth product, 13V/us slew rate, and a 3.0V to 44V supply range in one 14-pin DIP. The onsemi product page identifies the MC33074 as a general-purpose operational-amplifier family. Suitability for a specific measurement chain should be checked against signal amplitude, common-mode limits, required accuracy, noise, and grounding conditions.
What is the best drop-in replacement for MC33074AP?
The MC33074APG is the closest same-family candidate identified for a possible package-level replacement because it is the onsemi MC33074 variant associated with the same quad bipolar amplifier family. A replacement should still be checked for exact package, pinout, temperature rating, offset voltage, and supply compatibility before use. The Request a Quote form on this page can identify additional sourcing options, but functional similarity alone does not establish drop-in compatibility.
Can MC33074APG replace MC33074AP?
MC33074APG can be considered as a candidate for MC33074AP because both belong to the onsemi MC33074 quad amplifier family and are associated with the same core performance characteristics. The manufacturer family description lists 4.5MHz gain-bandwidth product, 13V/us slew rate, bipolar fabrication, and operation from 3.0V to 44V. Confirm the exact lead package, pinout, operating-temperature range, and ordering suffix against the manufacturer datasheet before making a substitution.
MC33074AP vs MC34074AP - which is better for an industrial control circuit?
The MC33074AP is the appropriate choice when the design specifically targets the MC33074 family's 3.0V to 44V operating range, 4.5MHz gain-bandwidth product, 13V/us slew rate, and 3mV offset specification. MC34074AP is a different onsemi amplifier family, so its supply range, input stage, offset, bias current, noise, and exact limits must be checked independently. Use the MC34074 only after confirming its pin-level and parametric compatibility.
When should I choose MC33074AP over MC33074APG?
Choose MC33074AP when its exact onsemi ordering code, 14-pin plastic DIP package, and specified electrical limits match the design requirements. Consider MC33074APG when its manufacturer-defined temperature grade, package form, or ordering configuration better fits the production build. Both are associated with the MC33074 family and its 4.5MHz bandwidth and 13V/us slew-rate characteristics, but the suffix-level specifications and package details determine the final choice.
Is MC33074AP the same as a standard quad op amp?
The MC33074AP is a standard general-purpose quad operational amplifier, but it is not automatically interchangeable with every other quad op amp. The onsemi MC33074 family uses bipolar construction and specifies a 3.0V to 44V supply range, 4.5MHz gain-bandwidth product, 13V/us slew rate, and 3mV input offset voltage. A valid replacement must also match the package, pinout, supply limits, common-mode behavior, output swing, and required noise performance.
What can replace MC33074AP?
MC33074APG is the most direct same-brand candidate located for a possible replacement because it is part of the onsemi MC33074 family and shares the family's core quad bipolar architecture. Exact compatibility must still be confirmed against the package and pin-description tables. No cross-brand candidate with documented pin compatibility and a complete 14-pin DIP footprint comparison was established, so an unqualified substitute should not be assumed.
What is the best onsemi equivalent for MC33074AP?
MC33074APG is the leading onsemi-family candidate for evaluating as an MC33074AP equivalent. It is associated with the same MC33074 family description: four monolithic bipolar operational amplifiers, 4.5MHz gain-bandwidth product, 13V/us slew rate, and 3.0V to 44V single-supply capability. The exact suffix, package, pinout, temperature range, and electrical limits should be compared with the MC33074AP datasheet before production use.
Where to buy MC33074AP online?
Use the Request a Quote form on this page to request MC33074AP availability, lead time, and ordering support from XAIPART. The manufacturer identifies the MC33074 as a standard operational-amplifier product, and current distributor listings show the exact MPN in a 14-pin plastic DIP configuration. Share the required quantity, date code, and target shipment location with the quote request to obtain a procurement-ready response.
What is the price and lead time of MC33074AP?
Current MC33074AP commercial terms are handled through the Request a Quote form on this page. Submit the required quantity, preferred package, date-code preference, and delivery destination so XAIPART can confirm price and lead time for the exact ordering code. The product is associated with a 14-pin plastic DIP package and the onsemi MC33074 family, but production scheduling and commercial availability should be confirmed for the requested quantity.
Is MC33074AP in stock?
MC33074AP availability should be confirmed through the Request a Quote form on this page for the exact quantity and delivery requirements. Current product listings identify the MC33074AP as a standard onsemi quad operational amplifier in a 14-pin plastic DIP package, but temporary inventory conditions can vary by order quantity and date code. Provide the required purchase quantity and target date to receive a current availability response.

এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা MC33074AP — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।

নির্বাচন গাইড

Choose MC33074AP when the board requires a general-purpose quad bipolar op amp in a 14-pin DIP, with a documented 3.0V to 44V supply range, 4.5MHz gain-bandwidth product, 13V/us slew rate, and 3mV input offset. It is well suited to industrial signal conditioning, active filtering, audio preamplification, and four-channel monitoring. Consider MC33074APG first when checking a same-family onsemi option, since it is associated with the same core performance characteristics; verify the suffix-specific package and temperature details before release. MC34074AP may be considered only after its electrical limits and exact pinout are confirmed against the design requirements. Neither candidate should be treated as an automatic replacement. The choice ultimately depends on the required accuracy, common-mode range, output swing, source impedance, temperature grade, and availability of the exact ordering code.

বিকল্পের সাথে তুলনা

পারামিটার এই পণ্য MC33074APG MC34074AP
Package 14-pin plastic DIP 14-pin plastic DIP 14-pin plastic DIP
Brand onsemi onsemi onsemi
Number of Amplifiers 4 4 4
Primary Application General-purpose quad signal conditioning General-purpose quad signal conditioning General-purpose quad operational amplifier
Mounting Type Through-hole Through-hole Through-hole

মূল পার্থক্যসমূহ

  • Four matched functional channels in one through-hole package (বনামMC34074AP)
  • Direct same-family configuration option (বনামMC33074APG)
  • Wide single-supply operating range (বনামMC34074AP)

ডিজাইন নোট

Place the supply bypass capacitor immediately adjacent to the MC33074AP power pins, with a short ground return to reduce supply impedance. The manufacturer specifies a 3.0V to 44V operating range, but this rating does not guarantee acceptable performance at every intermediate supply voltage. Verify input common-mode range, output swing, quiescent current, and thermal conditions at the actual rail. For split supplies, confirm the total voltage and ground handling requirements against the family documentation.

Keep each op-amp feedback loop compact and route output signals away from high-impedance input nodes to reduce parasitic coupling and oscillation risk. Four amplifiers in one package share supply pins, so high-current outputs should not create large voltage drops in common traces. Use a solid ground plane, keep unused inputs at a defined common-mode potential rather than leaving them floating, and follow the manufacturer pin-description table when assigning the 14 DIP leads.

The 4.5MHz gain-bandwidth product and 13V/us slew rate are not guarantees of usable closed-loop bandwidth at every gain. Select the feedback resistors and capacitors for the intended closed-loop response, and verify stability using the manufacturer's typical-performance information. Include the 3mV input offset in DC accuracy calculations and check input bias current against the source impedance, particularly when operating with high-impedance sensors.

Do not assume that every 14-pin quad amplifier is pin compatible with the MC33074AP. Confirm the exact package, pin numbering, power connections, input/output assignments, and common-mode limits before replacing a component. Also verify that a proposed substitute meets the required 3.0V to 44V supply range, offset voltage, bandwidth, slew rate, and temperature requirements. Functional descriptions such as quad amplifier or instrumentation amplifier do not establish drop-in compatibility.

কমপ্লায়েন্স তথ্য

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
লিড ফ্রি
Unknown
হ্যালোজেন ফ্রি
Unknown
কনফ্লিক্ট মিনারেলস
Unknown

Compliance declarations were not included in the product listing. Check the current onsemi product documentation and declaration files for the exact MC33074AP ordering code before making a compliance claim.

ডেটা যাচাই করা হয়েছে: 2026-11-16 — ডেটা XAIPART-এর কম্পোনেন্ট ইঞ্জিনিয়ারিং টিম দ্বারা যাচাই ও কিউরেট করা হয়েছে

সম্পর্কিত অনুসন্ধান

MC33074AP datasheet MC33074AP pinout MC33074AP datasheet pdf MC33074AP equivalent MC33074AP replacement MC33074AP cross reference MC33074AP vs MC33074APG MC33074AP 14-DIP footprint MC33074AP 44V quad op amp MC33074AP 4.5MHz 13V/us MC33074AP price MC33074AP stock onsemi MC33074AP MC33074AP industrial signal conditioning

সম্পর্কিত কম্পোনেন্ট ও শর্তাবলী

onsemi MC33074AP MC33074APG MC34074AP MC33074 quad operational amplifier general-purpose operational amplifier bipolar operational amplifier amplifier IC analog semiconductor single-supply operation gain-bandwidth product slew rate input offset voltage input bias current active filter signal conditioning industrial instrumentation audio preamplifier 14-pin plastic DIP through-hole package surface-mount transition feedback network power-supply bypassing
তাৎক্ষণিক বিলওয়াছে রেকোজিউইট
সম্পূর্ণ বিবরণ পূরণ করুন — আমাদের সেলস টিম 24 ঘণ্টার মধ্যে উত্তর দেবে
পার্ট নম্বর উৎপাদক প্যাকেজ QTY লক্ষ্যমূল্য প্রসারিত
✓
বিল প্রস্তুত করা হয়েছে!

আমরা ২৪ ঘণ্টার মধ্যে আপনার ইমেইলে প্রত্যুত্তর দেব

1
RFQ জমা হয়েছে
2
কোটেশন পাওয়া গেছে
3
অর্ডার দেওয়া হয়েছে
4
পেমেন্ট
5
শিপ করা হয়েছে
6
ডেলিভারি হয়েছে
RFQ বিবরণ দেখুন