MC33074AP - 44V Quad Op Amp, 4.5MHz, 14-DIP | onsemi
Teilenummer: MC33074AP ✓ AktivMC33074AP Übersicht
An operational amplifier, or op amp, is a high-gain differential amplifier whose open-loop behavior is shaped by external feedback. The MC33074AP belongs to the bipolar operational-amplifier family within the broader amplifier IC and analog semiconductor hierarchy. Each of its four channels can operate from a common positive supply and ground while supporting applications that involve signal amplification, buffering, comparisons, summing, and feedback-controlled analog circuits.
The MC33074AP combines a 4.5MHz gain-bandwidth product with a 13V/us slew rate, allowing useful bandwidth beyond audio frequencies and rapid output transitions in transient signals. Its 3mV input offset voltage provides a defined level of input imbalance that must be included in precision-chain error budgets. The 3.0V to 44V supply range covers low-voltage circuits, conventional ±15V industrial systems, and higher single-supply rails. The monolithic quad construction reduces the number of separate amplifier packages required on a board.
The bipolar internal design avoids the input-bias-current behavior associated with JFET-input amplifiers. This makes the MC33074AP appropriate for general-purpose signal conditioning where input bias current, offset voltage, slew rate, and supply range are the principal selection criteria. Because four amplifiers share one package, thermal behavior, supply decoupling, unused-channel handling, and channel-to-channel matching should be considered together rather than treating each section as an isolated component.
Typical uses include industrial sensor interfaces, low-level control-signal amplification, audio preamplification, active filtering, waveform conditioning, and four-channel monitoring systems. The 44V maximum supply also provides headroom for systems with elevated rail voltages, although the complete circuit must remain within the absolute maximum ratings of every connected device. Grounded-source sensors, transducers, and analog front ends can benefit from the channel count and common package organization.
For a new design, confirm the 14-pin DIP footprint and verify every pin function against the manufacturer pin-description table before layout release. Place the power-supply bypass capacitor close to the supply pin, provide a stable ground reference, and avoid leaving unused op-amp inputs floating. Confirm output swing, common-mode range, stability with the intended feedback network, and required noise performance at the actual supply voltage and signal frequency.
This product page combines the manufacturer device information with practical supply, layout, comparison, and selection guidance. It also distinguishes exact package compatibility from merely similar amplifier functions, helping engineers identify replacements that can be considered for a PCB-level substitution and those that require a broader redesign.
Drop-in-Alternativen für MC33074AP – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
MC33074APG
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
MC34074AP
✅ Drop-In ⚠️ Spezifikationen ungeprüft📋 Referenzalternative (nicht im Katalog)
MC33074AP Grenzwerte & elektrische Eigenschaften
| Number of Amplifiers | 4 amplifiers |
| Amplifier Type | Single-ended general-purpose operational amplifier |
| Supply Voltage Range | 3.0V to 44V |
| Gain-Bandwidth Product | 4.5MHz |
| Slew Rate | 13V/us |
| Input Offset Voltage | 3mV |
| Internal Transistor Technology | Bipolar |
| Gehäuse | 14-pin plastic DIP |
| Montageart | Through-hole |
| Number of Channels | 4 |
MC33074AP 14-pin plastic dip Pinbelegungsleitfaden
Pinbelegung für MC33074AP (14-pin plastic dip-Gehäuse). Dieses analoge Bauteil verfügt über Eingangs-, Ausgangs- und Versorgungspins. Offset-Null-, Kompensations- und Enable-Pin-Konfigurationen entnehmen Sie dem Herstellerdatenblatt. Ideal für Signalaufbereitung und Verstärkerschaltungen.
Keine detaillierten Pinbelegungsdaten verfügbar für MC33074AP.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
MC33074AP ist geeignet für 6 Anwendungs: Industrial Sensor Signal Conditioning, Active Audio Preamplification, Precision Filter and Integrator Design, Quad-Channel Control Monitoring, Data Acquisition Front End, General Instrumentation Buffering.
Industrial Sensor Signal Conditioning
The MC33074AP fits four-channel industrial sensor conditioning because it combines four amplifiers in one 14-pin DIP and accepts a 3.0V to 44V supply. Each channel can amplify a low-level transducer signal and establish the gain required by a downstream controller. The 4.5MHz gain-bandwidth product provides more bandwidth than the signal path commonly requires, while 13V/us slew rate allows comparatively rapid response to step changes. Designers should still verify the input common-mode range, output swing, offset error, and source impedance for the selected sensor. The 3mV input offset contributes directly to signal accuracy, particularly when the conditioned output is near the lower end of the controller input range.
Empfohlen
Active Audio Preamplification
The MC33074AP can provide four general-purpose preamplifier channels in audio and communication equipment. Its 4.5MHz gain-bandwidth product covers the audio band with additional bandwidth margin, while the 13V/us slew rate can improve large-signal transient handling compared with slower amplifiers. The 3.0V to 44V supply range permits operation from compact single-supply rails or conventional bipolar-style supplies within the device limits. Four channels in one package simplify the physical design when sources require independent buffering or gain stages. Audio design should account for input offset, output-headroom limits, noise, and the need for an output coupling or biasing solution in single-supply configurations.
Empfohlen
Precision Filter and Integrator Design
The MC33074AP is suitable for active filters, integrators, and closed-loop control blocks because its four bipolar operational amplifiers can form independent active stages. The 4.5MHz gain-bandwidth product gives designers useful open-loop loop gain near the selected signal frequencies, which can improve closed-loop accuracy when the operating frequency remains appropriately below the amplifier bandwidth. A 13V/us slew rate supports signals with finite edge rates. Component tolerances and the amplifier's 3mV input offset can influence DC accuracy, especially in integrators where offset accumulates over time. Stable feedback-network layout and common supply decoupling are essential for repeatable filter behavior.
Empfohlen
Quad-Channel Control Monitoring
A single MC33074AP package can implement four closely related control or monitoring channels where a quad DIP footprint simplifies assembly. Each amplifier can buffer a sensor, comparator-style threshold signal, or error amplifier in a multi-axis system. The 3.0V to 44V operating range accommodates control systems with different rail architectures, while the 4.5MHz bandwidth and 13V/us slew rate support signals beyond slow DC-only operation. All four channels share the same package and supply, so power-distribution design should avoid long traces between the bypass capacitor and the supply pins. Engineers should verify channel-specific output loading, saturation recovery, and any required isolation between command and feedback paths.
Empfohlen
Data Acquisition Front End
The MC33074AP can serve as the first amplification stage in a multi-channel data-acquisition front end when the source impedance, bandwidth, and accuracy requirements fit its bipolar input characteristics. Its 4.5MHz gain-bandwidth product and 13V/us slew rate provide ample bandwidth for many sensor and control signals, while four channels reduce the number of packages on the board. The 3mV input offset must be included in the overall accuracy calculation, and the common-mode and output-swing limits constrain the usable signal range. Pairing the amplifiers with suitable high-impedance sensors and carefully designed protection can create a practical conditioning stage, but source loading and anti-aliasing requirements must be evaluated independently.
Empfohlen
General Instrumentation Buffering
The MC33074AP is appropriate for general instrumentation buffering where four measurement or control signals must be conditioned with a bipolar operational amplifier. Its 4.5MHz gain-bandwidth product supports moderate-bandwidth signals, and the 13V/us slew rate limits large-signal distortion for rapidly changing waveforms. The common 3.0V to 44V supply range simplifies procurement for laboratories, industrial panels, and embedded test equipment that use several rail arrangements. Buffering does not eliminate the need for an input common-mode check: the amplifier must remain within its linear input range, and outputs must not saturate at the selected rail voltage. Stable reference grounding and short feedback paths are essential when preserving low-level measurement accuracy.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für MC33074AP – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | MC33074APG | MC34074AP |
|---|---|---|---|
| Package | 14-pin plastic DIP | 14-pin plastic DIP | 14-pin plastic DIP |
| Brand | onsemi | onsemi | onsemi |
| Number of Amplifiers | 4 | 4 | 4 |
| Primary Application | General-purpose quad signal conditioning | General-purpose quad signal conditioning | General-purpose quad operational amplifier |
| Mounting Type | Through-hole | Through-hole | Through-hole |
Wichtigste Unterscheidungsmerkmale
- Four matched functional channels in one through-hole package (vs. MC34074AP)
- Direct same-family configuration option (vs. MC33074APG)
- Wide single-supply operating range (vs. MC34074AP)
Designhinweise
Place the supply bypass capacitor immediately adjacent to the MC33074AP power pins, with a short ground return to reduce supply impedance. The manufacturer specifies a 3.0V to 44V operating range, but this rating does not guarantee acceptable performance at every intermediate supply voltage. Verify input common-mode range, output swing, quiescent current, and thermal conditions at the actual rail. For split supplies, confirm the total voltage and ground handling requirements against the family documentation.
Keep each op-amp feedback loop compact and route output signals away from high-impedance input nodes to reduce parasitic coupling and oscillation risk. Four amplifiers in one package share supply pins, so high-current outputs should not create large voltage drops in common traces. Use a solid ground plane, keep unused inputs at a defined common-mode potential rather than leaving them floating, and follow the manufacturer pin-description table when assigning the 14 DIP leads.
The 4.5MHz gain-bandwidth product and 13V/us slew rate are not guarantees of usable closed-loop bandwidth at every gain. Select the feedback resistors and capacitors for the intended closed-loop response, and verify stability using the manufacturer's typical-performance information. Include the 3mV input offset in DC accuracy calculations and check input bias current against the source impedance, particularly when operating with high-impedance sensors.
Do not assume that every 14-pin quad amplifier is pin compatible with the MC33074AP. Confirm the exact package, pin numbering, power connections, input/output assignments, and common-mode limits before replacing a component. Also verify that a proposed substitute meets the required 3.0V to 44V supply range, offset voltage, bandwidth, slew rate, and temperature requirements. Functional descriptions such as quad amplifier or instrumentation amplifier do not establish drop-in compatibility.
Compliance-Informationen
Compliance declarations were not included in the product listing. Check the current onsemi product documentation and declaration files for the exact MC33074AP ordering code before making a compliance claim.