onsemi

MC33204PG - Quad Rail-to-Rail Op Amp | onsemi

MPN: MC33204PG ✓ সক্রিয়
1.8 V to 12 V Vdss 14-pin PDIP Package
সর্বনিম্ন অর্ডার পরিমাণ: 1 |

MC33204PG সারাংশ

The onsemi MC33204PG is a quad general-purpose operational amplifier with rail-to-rail input and output operation in a 14-pin PDIP package. It provides four amplifiers per device, a 2.2 MHz gain-bandwidth product, and a 1 V/us slew rate. The MC33204 operates from 1.8 V to 12 V, making it suitable for low-voltage battery-powered, industrial control, sensor-conditioning, and general signal-processing systems.

An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. A rail-to-rail input amplifier accepts common-mode input voltages close to the positive and negative supply rails, while a rail-to-rail output amplifier can swing its output close to those rails. This expands the usable input and output range compared with conventional fixed-range amplifiers, especially when the supply voltage is only a few volts above the signal amplitude.

The MC33204 family combines four amplifiers in one package, reducing board area and simplifying multi-channel designs where identical amplifier performance is useful. Its inputs may be driven approximately 200 mV beyond the supply rails without phase reversal at the outputs. The output can swing to within approximately 50 mV of either rail. A gain-bandwidth product of 2.2 MHz supports signal bandwidths suitable for audio, instrumentation, filtering, and feedback-control circuits.

The 1 V/us slew rate provides practical full-power-bandwidth capability for low- and mid-frequency analog signals. The device is intended for general-purpose amplification rather than high-speed precision applications, so input offset voltage, input bias current, noise density, and stability characteristics should be reviewed against the precision required by each circuit. Decoupling capacitors should be placed close to the supply pins to control impedance in feedback networks and prevent oscillation.

Typical uses include low-voltage sensor interfaces, current-to-voltage conversion, active filtering, audio summing stages, joystick and touch inputs, and general instrumentation. Because the MC33204PG contains four matched-function amplifiers in one PDIP package, it is especially useful where a design needs several channels of similar gain, bandwidth, and output-drive capability.

When designing with the MC33204, verify that the signal and output ranges remain within the rail limits at the lowest operating supply voltage. Check the required common-mode range for sensor outputs and confirm that capacitive loads connected to the output remain inside the stable operating region. Use the pin-description table in the onsemi MC33204 datasheet when assigning PCB tracks.

This page combines the manufacturer product information with ordering details, drop-in replacement analysis, application guidance, and practical design notes. It helps engineers evaluate the MC33204PG for low-voltage analog signal chains while keeping package, sourcing, and circuit-integration considerations in one place.

এর জন্য ড্রপ-ইন বিকল্প MC33204PG — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।

এই সিরিজের ভ্যারিয়েন্ট

একই সিরিজের মডেল যেগুলো drop-in compatible MC33204PG (একই form factor এবং footprint) — পার্থক্য রয়েছে Package.

onsemi
Package: 14-pin plastic dual in-line package
এর সাথে তুলনা করুন MC33204PG →

MC33204P

✅ ড্রপ-ইন
onsemi
📦 14-pin PDIP
General-purpose operational amplifier · 4 circuits · 1.8 V to 12 V · Yes · Yes · 200 mV without output phase reversal · Within 50 mV of each rail · 14-pin plastic dual in-line package

মূল্যের জন্য যোগাযোগ করুন

ডেটাশিট দেখুন →

MC33204PG সর্বোচ্চ রেটিং ও বৈদ্যুতিক বৈশিষ্ট্য

Number of Amplifiers 4 circuits
Amplifier Type General-purpose operational amplifier
Input Common-Mode Range Rail-to-rail
Output Swing Rail-to-rail, within approximately 50 mV of each rail
Maximum Input Overdrive Approximately 200 mV beyond the supply rails without output phase reversal
Supply Voltage Range 1.8 V to 12 V
Gain-Bandwidth Product 2.2 MHz
Slew Rate 1 V/us
প্যাকেজ 14-pin PDIP
প্যাকেজ / কেস 14-DIP (0.300 in, 7.62 mm pitch)
মাউন্টিং টাইপ Through-hole
Packaging Type Tube
Unity-Gain Bandwidth 2.2 MHz

MC33204PG পিন কনফিগারেশন

DIP-14 Package Pinout Diagram DIP-14 14-pin dual inline, 7.62mm pitch, JEDEC MS-001. 1 14 2 13 3 12 4 11 5 10 6 9 7 8 DIP-14
পিন 1 OUT1 — Amplifier 1 output
পিন 2 IN1- — Amplifier 1 inverting input
পিন 3 IN1+ — Amplifier 1 non-inverting input
পিন 4 V- — Negative supply connection
পিন 5 IN2+ — Amplifier 2 non-inverting input
পিন 6 IN2- — Amplifier 2 inverting input
পিন 7 OUT2 — Amplifier 2 output
পিন 8 OUT3 — Amplifier 3 output
পিন 9 IN3- — Amplifier 3 inverting input
পিন 10 IN3+ — Amplifier 3 non-inverting input
পিন 11 V+ — Positive supply connection
পিন 12 IN4+ — Amplifier 4 non-inverting input
পিন 13 IN4- — Amplifier 4 inverting input
পিন 14 OUT4 — Amplifier 4 output

সাধারণ ব্যবহার

MC33204PG এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Low-Voltage Sensor Signal Conditioning, Active Filtering and Gain Stages, Current-to-Voltage Conversion, Audio Preamp and Summing Stages, Industrial Control and Data Acquisition, Joystick, Touch, and Position Interfaces.

🧩

Low-Voltage Sensor Signal Conditioning

The MC33204PG suits low-energy sensor front ends because each of its four amplifiers accepts and produces signals close to the supply rails. The 1.8 V minimum supply and rail-to-rail operation preserve usable headroom when a sensor, resistive divider, or transducer operates near a 3.3 V rail. A 2.2 MHz gain-bandwidth product supports moderate-bandwidth conditioning stages, while the 1 V/us slew rate handles typical sensor transients. Configure the gain so bandwidth remains adequate at the selected closed-loop gain, and verify offset, noise, and bias-current requirements against the sensor source impedance.

🌐

Active Filtering and Gain Stages

The MC33204PG can implement four similar active-filter or fixed-gain stages on one board when each channel operates within the same bandwidth and stability limits. Its 2.2 MHz gain-bandwidth product provides useful closed-loop bandwidth for audio-range and instrumentation filters, and the 1 V/us slew rate limits large-signal distortion. Keep the feedback network close to the amplifier and follow the manufacturer stability guidance for capacitive loading. Rail-to-rail input and output capability is especially helpful when the filter must accept or generate signals near the low supply rails.

⚡

Current-to-Voltage Conversion

The MC33204PG is useful in current-measurement front ends because its rail-to-rail inputs accept the voltage generated by a shunt or current-feedback network with minimal wasted signal range. Four channels allow a design to monitor several currents when their gain and bandwidth requirements are similar. The 2.2 MHz gain-bandwidth product supports shunt-amplifier bandwidths common in laboratory and industrial control equipment, while the 1 V/us slew rate provides useful dynamic range for rapidly changing current waveforms. Compensation must account for the shunt and feedback parasitic capacitance.

🎧

Audio Preamp and Summing Stages

The MC33204PG can serve as a quad low-voltage audio preamp when the design requires input and output headroom close to the operating rails. Its rail-to-rail input stage accepts small microphone-level or line-level signals, and the rail-to-rail output reduces distortion when the signal approaches the available output range. The 2.2 MHz gain-bandwidth product exceeds the bandwidth of many audio-band signal paths, while the 1 V/us slew rate supports moderate output amplitudes. Confirm output-current limits, noise performance, and the maximum input signal before setting closed-loop gain.

🏭

Industrial Control and Data Acquisition

The MC33204PG is appropriate for industrial interface boards requiring several low-voltage amplifier channels without allocating a separate package for each signal. Rail-to-rail inputs help accommodate outputs from sensors and control converters operating close to 5 V or 3.3 V rails, while the output stage can drive downstream ADC drivers within its current capability. Its general-purpose 2.2 MHz bandwidth suits slow process-control, transducer, and monitoring loops rather than high-speed data capture. Protection, grounding, and isolation requirements determine how closely the amplifier should be placed to the field wiring.

📱

Joystick, Touch, and Position Interfaces

The MC33204PG can buffer resistive, capacitive, or position-sensing inputs that operate on low-voltage rails. Rail-to-rail inputs preserve signal amplitude at the ends of the sensor's travel, and the output stage can present the conditioned level to a controller or comparator. Four channels are useful when a system combines multiple analog controls, and the 2.2 MHz gain-bandwidth product is adequate for many human-interface and low-frequency position systems. Check input capacitance, sensor drive requirements, and any filtering needed to reject switching or display noise.

What is the onsemi MC33204PG?
The onsemi MC33204PG is a quad general-purpose operational amplifier with rail-to-rail input and output operation in a 14-pin PDIP package. According to the onsemi MC33204 product page, it contains four amplifiers, operates across a 1.8 V to 12 V supply range, and provides a 2.2 MHz gain-bandwidth product with a 1 V/us slew rate. It is intended for low-voltage analog signal conditioning, instrumentation, filtering, and multi-channel amplifier applications.
What are the key specifications of MC33204PG that engineers should know?
The MC33204PG provides four rail-to-rail input and output amplifiers, a 2.2 MHz gain-bandwidth product, and a 1 V/us slew rate from a 1.8 V to 12 V supply. The onsemi MC33204 datasheet also states that the inputs may be driven approximately 200 mV beyond the supply rails without phase reversal, while outputs swing to within approximately 50 mV of either rail. The 14-pin PDIP package supports through-hole assembly and prototype or legacy designs.
Can MC33204PG accept input signals above the supply voltage?
Yes. The onsemi MC33204 datasheet states that the inputs can be driven as high as approximately 200 mV beyond the supply rails without phase reversal on the outputs. This overvoltage tolerance is useful when a sensor output approaches or briefly exceeds the rail-limited input range. It does not remove the need to protect the device from large or sustained overvoltage, so external clamping may still be required in exposed industrial systems.
How close to the supply rails can the MC33204PG output swing?
The MC33204PG has a rail-to-rail output stage, and the onsemi MC33204 family documentation states that the output can swing within approximately 50 mV of each supply rail. Actual headroom depends on supply voltage, output current, and device temperature. When a downstream circuit requires nearly the full rail-to-rail range, verify the output-voltage-versus-current curves in the manufacturer datasheet for the operating load.
What is the difference between MC33204PG and MC33204P?
The MC33204PG and MC33204P have consistent terminal assignments and package construction, allowing the ordered form to be used where the same 14-pin PDIP footprint is required. The orderable suffix indicates the packaging presentation: the MC33204PG is listed in tube packaging. The electrical function, amplifier count, supply range, bandwidth, and pin arrangement remain the relevant board-level considerations when checking a replacement.
Is MC33204PG suitable for low-voltage sensor conditioning?
The MC33204PG is well suited to low-voltage sensor conditioning because its inputs and outputs operate rail-to-rail from a 1.8 V to 12 V supply. A 2.2 MHz gain-bandwidth product supports common sensor, filtering, and buffering stages, while the 1 V/us slew rate handles moderate-amplitude signals. Choose the gain, source impedance, and compensation network to maintain stability, and confirm the sensor's output range against the input common-mode limits.
What is the best drop-in replacement for MC33204PG?
The MC33204P is the closest identified same-family choice because it has the same functional parameters, 14-pin PDIP terminal arrangement, and package construction; the primary documented difference is the orderable packaging presentation. When substituting a different manufacturer's amplifier, confirm rail-to-rail input and output behavior, supply range, unity-gain stability, output-current capability, and the exact pinout. A nominal quad-op-amp replacement should not be accepted without those checks.
Can an LM324 replace the MC33204PG?
An LM324 can use a 14-pin PDIP footprint in some board layouts, but it is not a direct functional replacement for the MC33204PG. The MC33204PG provides rail-to-rail input and output operation and a specified 2.2 MHz gain-bandwidth product with 1 V/us slew rate. An LM324 has different input-range, output-swing, bandwidth, noise, and stability characteristics, so verify every operating requirement before substituting it.
When should I choose MC33204PG over a conventional quad op amp?
Choose the MC33204PG when a low-voltage circuit needs usable input and output ranges close to the supply rails. Its rail-to-rail operation preserves signal headroom at 1.8 V and higher supplies, while four amplifiers in one 14-pin PDIP package simplify multi-channel designs. A conventional amplifier may remain preferable when low cost dominates, the signal range is far from the rails, and the exact offset, noise, and stability characteristics suit the application.
Where can I download the MC33204PG datasheet PDF?
Download the MC33204 family documentation from the onsemi MC33204 product page linked on this page. The manufacturer datasheet describes the rail-to-rail input and output behavior, the 1.8 V to 12 V operating range, the 2.2 MHz gain-bandwidth product, the 1 V/us slew rate, electrical characteristics, and the 14-pin pin assignment. Use the pin-description table and characteristic curves when finalizing a schematic or PCB layout.
Where can I find the MC33204PG 14-pin pinout?
The MC33204PG pinout is defined in the onsemi MC33204 datasheet for the 14-pin PDIP package. Pin 1 is the output of amplifier 1, and the package follows the standard dual-inline outline with a notch identifying the end of the device. When assigning PCB tracks, use the manufacturer pin-description table to identify output, input, positive-supply, and negative-supply connections on every amplifier channel.
How should decoupling capacitors be placed around the MC33204PG?
Place the supply bypass capacitors as close as practical to the positive and negative supply pins of the MC33204PG. Short, low-inductance return paths help prevent feedback-network oscillation and reduce the influence of supply impedance on output behavior. The manufacturer's typical-application circuit is the appropriate reference for capacitor placement and values, while the completed layout should keep copper returns compact and electrically continuous.
Does the MC33204PG need a heatsink?
The MC33204PG normally does not require a heatsink in low-voltage, low-current signal-conditioning applications because its supply voltage is limited to 12 V and most of the dissipated power occurs in the amplifier output stage. Dissipation rises with output current, the voltage difference between the output and the lower rail, and ambient temperature. Review the package thermal information and estimate worst-case dissipation before deciding whether copper spreading is sufficient.
Where can I buy MC33204PG and what is the lead time?
MC33204PG can be ordered through the Request a Quote form on this page, which allows you to confirm current inventory, order quantity, and lead time for the 14-pin PDIP device. The listing identifies the component as a tube-packaged, through-hole operational amplifier. Because production schedules and stock levels change, request a written quotation for the quantity and delivery schedule required by your build.
Is MC33204PG available in stock?
Current stock status should be confirmed through the Request a Quote form on this page rather than treated as a fixed value. The MC33204PG is listed as a standard onsemi product and is available in a 14-pin PDIP tube package. Submit your required quantity, target date, and any date-code or traceability requirements so the order can be scheduled against current channel inventory.
What is the onsemi MC33204PG price?
Use the Request a Quote form on this page for the current MC33204PG quotation. The form is the appropriate route for quantity pricing, schedule, and availability because commercial terms can change with order size, lead time, and channel inventory. Submit the required tube quantity and target delivery date to receive a current response for this exact 14-pin PDIP orderable MPN.
What can replace the MC33204PG in a legacy design?
The MC33204P is the closest same-family replacement because it retains the functional parameters, terminal arrangement, and 14-pin PDIP package construction, with packaging presentation as the practical ordering difference. Other amplifier families may fit the footprint but can differ in rail-to-rail behavior, bandwidth, slew rate, stability, and output drive. Check the schematic, feedback configuration, supply voltage, load, and required common-mode range before approving any substitute.

এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা MC33204PG — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।

নির্বাচন গাইড

Choose the MC33204PG when a legacy or industrial through-hole design needs four general-purpose amplifiers with rail-to-rail input and output operation from a 1.8 V to 12 V supply. It is particularly useful when sensor, filter, audio, or interface signals operate close to the supply rails and the 2.2 MHz bandwidth is adequate. The MC33204P is the closest identified drop-in alternative when its orderable packaging presentation suits the assembly plan. Other quad amplifiers should be considered only after checking input common-mode range, output swing, gain-bandwidth product, slew rate, output drive, unity-gain stability, and the complete 14-pin terminal assignment. For high-precision or high-speed instrumentation, verify offset voltage, bias current, noise, and dynamic-range requirements before committing to this general-purpose amplifier family.

বিকল্পের সাথে তুলনা

পারামিটার এই পণ্য MC33204P
Brand onsemi onsemi
Package 14-pin PDIP 14-pin PDIP - same
Number of Amplifiers 4 4
Supply Voltage Range 1.8 V to 12 V 1.8 V to 12 V
Input Common-Mode Range Rail-to-rail Rail-to-rail
Output Swing Rail-to-rail, within approximately 50 mV of each rail Rail-to-rail, within approximately 50 mV of each rail
Gain-Bandwidth Product 2.2 MHz 2.2 MHz
Slew Rate 1 V/us 1 V/us
Input Overdrive Tolerance Approximately 200 mV beyond the supply rails without phase reversal Approximately 200 mV beyond the supply rails without phase reversal

মূল পার্থক্যসমূহ

  • Four rail-to-rail amplifiers in one through-hole package (বনামMC33204P)
  • Usable signal headroom from low-voltage supplies (বনামMC33204P)
  • Input overdrive behavior for sensor interfaces (বনামMC33204P)

ডিজাইন নোট

Keep the MC33204 supply within the 1.8 V to 12 V device range and account for rail-to-rail output headroom at the lowest operating supply. Place bypass capacitors close to the V+ and V- pins with short, low-inductance connections. When the amplifier sources current near its limit, verify the output-current capability and dissipation in the manufacturer characteristic curves rather than assuming full rail-to-rail swing under load.

Rail-to-rail input operation does not make the amplifier immune to supply-referenced overvoltage. Although the inputs tolerate approximately 200 mV beyond the rails, sustained large excursions can damage internal input structures. In exposed systems, use series resistance, clamping devices, or an appropriate protection network. Also avoid assuming that a 14-pin quad amplifier from another family is interchangeable solely because its package has 14 leads.

Route the sensitive input and feedback nodes as short as possible, keep the feedback components close to the amplifier, and maintain a continuous ground plane beneath the circuit. Place the supply bypass network at the power pins and separate it from high-current switching paths. When driving capacitive loads, use an isolation resistor or an output-buffer arrangement if the load can exceed the device's stable operating region.

কমপ্লায়েন্স তথ্য

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
লিড ফ্রি
Unknown
হ্যালোজেন ফ্রি
Unknown
কনফ্লিক্ট মিনারেলস
Unknown

The onsemi product page identifies MC33204 as a standard operational amplifier product. No explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals statement was available for this orderable MPN, so those fields remain unknown. AEC-Q100 qualification is not applicable to this general-purpose commercial amplifier.

ডেটা যাচাই করা হয়েছে: 2026-11-16 — ডেটা XAIPART-এর কম্পোনেন্ট ইঞ্জিনিয়ারিং টিম দ্বারা যাচাই ও কিউরেট করা হয়েছে

সম্পর্কিত অনুসন্ধান

MC33204PG datasheet MC33204PG datasheet pdf MC33204PG pinout onsemi MC33204PG MC33204PG 14 pin PDIP MC33204PG rail to rail op amp MC33204PG 2.2MHz MC33204PG drop-in replacement MC33204P vs MC33204PG MC33204PG price MC33204PG stock MC33204PG sensor amplifier MC33204PG active filter circuit

সম্পর্কিত কম্পোনেন্ট ও শর্তাবলী

onsemi MC33204PG MC33204P MC33201P MC33202P operational amplifier quad operational amplifier general-purpose amplifier rail-to-rail input rail-to-rail output low-dropout analog signal conditioning gain-bandwidth product slew rate input common-mode range PDIP package dual inline package through-hole mount tube packaging sensor interface active filter current-to-voltage conversion audio preamplifier industrial control input overdrive tolerance
তাৎক্ষণিক বিলওয়াছে রেকোজিউইট
সম্পূর্ণ বিবরণ পূরণ করুন — আমাদের সেলস টিম 24 ঘণ্টার মধ্যে উত্তর দেবে
পার্ট নম্বর উৎপাদক প্যাকেজ QTY লক্ষ্যমূল্য প্রসারিত
✓
বিল প্রস্তুত করা হয়েছে!

আমরা ২৪ ঘণ্টার মধ্যে আপনার ইমেইলে প্রত্যুত্তর দেব

1
RFQ জমা হয়েছে
2
কোটেশন পাওয়া গেছে
3
অর্ডার দেওয়া হয়েছে
4
পেমেন্ট
5
শিপ করা হয়েছে
6
ডেলিভারি হয়েছে
RFQ বিবরণ দেখুন