MC33204PG - Quad Rail-to-Rail Op Amp | onsemi
MPN: MC33204PG ✓ פעילMC33204PG סקירה
An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. A rail-to-rail input amplifier accepts common-mode input voltages close to the positive and negative supply rails, while a rail-to-rail output amplifier can swing its output close to those rails. This expands the usable input and output range compared with conventional fixed-range amplifiers, especially when the supply voltage is only a few volts above the signal amplitude.
The MC33204 family combines four amplifiers in one package, reducing board area and simplifying multi-channel designs where identical amplifier performance is useful. Its inputs may be driven approximately 200 mV beyond the supply rails without phase reversal at the outputs. The output can swing to within approximately 50 mV of either rail. A gain-bandwidth product of 2.2 MHz supports signal bandwidths suitable for audio, instrumentation, filtering, and feedback-control circuits.
The 1 V/us slew rate provides practical full-power-bandwidth capability for low- and mid-frequency analog signals. The device is intended for general-purpose amplification rather than high-speed precision applications, so input offset voltage, input bias current, noise density, and stability characteristics should be reviewed against the precision required by each circuit. Decoupling capacitors should be placed close to the supply pins to control impedance in feedback networks and prevent oscillation.
Typical uses include low-voltage sensor interfaces, current-to-voltage conversion, active filtering, audio summing stages, joystick and touch inputs, and general instrumentation. Because the MC33204PG contains four matched-function amplifiers in one PDIP package, it is especially useful where a design needs several channels of similar gain, bandwidth, and output-drive capability.
When designing with the MC33204, verify that the signal and output ranges remain within the rail limits at the lowest operating supply voltage. Check the required common-mode range for sensor outputs and confirm that capacitive loads connected to the output remain inside the stable operating region. Use the pin-description table in the onsemi MC33204 datasheet when assigning PCB tracks.
This page combines the manufacturer product information with ordering details, drop-in replacement analysis, application guidance, and practical design notes. It helps engineers evaluate the MC33204PG for low-voltage analog signal chains while keeping package, sourcing, and circuit-integration considerations in one place.
חלופות תחליף ישיר עבור MC33204PG — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
וריאנטים בסדרה זו
דגמים מאותה סדרה התואמים Drop-in עם MC33204PG (אותו גורם צורה וטביעת רגל) — שונים ב Package.
MC33204P
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←MC33204PG דירוגים מרביים ומאפיינים חשמליים
| Number of Amplifiers | 4 circuits |
| Amplifier Type | General-purpose operational amplifier |
| Input Common-Mode Range | Rail-to-rail |
| Output Swing | Rail-to-rail, within approximately 50 mV of each rail |
| Maximum Input Overdrive | Approximately 200 mV beyond the supply rails without output phase reversal |
| Supply Voltage Range | 1.8 V to 12 V |
| Gain-Bandwidth Product | 2.2 MHz |
| Slew Rate | 1 V/us |
| מארז | 14-pin PDIP |
| מארז / Case | 14-DIP (0.300 in, 7.62 mm pitch) |
| סוג הרכבה | Through-hole |
| Packaging Type | Tube |
| Unity-Gain Bandwidth | 2.2 MHz |
תצורת פינים של MC33204PG
| פין 1 | OUT1 — Amplifier 1 output |
| פין 2 | IN1- — Amplifier 1 inverting input |
| פין 3 | IN1+ — Amplifier 1 non-inverting input |
| פין 4 | V- — Negative supply connection |
| פין 5 | IN2+ — Amplifier 2 non-inverting input |
| פין 6 | IN2- — Amplifier 2 inverting input |
| פין 7 | OUT2 — Amplifier 2 output |
| פין 8 | OUT3 — Amplifier 3 output |
| פין 9 | IN3- — Amplifier 3 inverting input |
| פין 10 | IN3+ — Amplifier 3 non-inverting input |
| פין 11 | V+ — Positive supply connection |
| פין 12 | IN4+ — Amplifier 4 non-inverting input |
| פין 13 | IN4- — Amplifier 4 inverting input |
| פין 14 | OUT4 — Amplifier 4 output |
יישומים טיפוסיים
MC33204PG מתאים עבור 6 יישוםs: Low-Voltage Sensor Signal Conditioning, Active Filtering and Gain Stages, Current-to-Voltage Conversion, Audio Preamp and Summing Stages, Industrial Control and Data Acquisition, Joystick, Touch, and Position Interfaces.
Low-Voltage Sensor Signal Conditioning
The MC33204PG suits low-energy sensor front ends because each of its four amplifiers accepts and produces signals close to the supply rails. The 1.8 V minimum supply and rail-to-rail operation preserve usable headroom when a sensor, resistive divider, or transducer operates near a 3.3 V rail. A 2.2 MHz gain-bandwidth product supports moderate-bandwidth conditioning stages, while the 1 V/us slew rate handles typical sensor transients. Configure the gain so bandwidth remains adequate at the selected closed-loop gain, and verify offset, noise, and bias-current requirements against the sensor source impedance.
מומלץ
Active Filtering and Gain Stages
The MC33204PG can implement four similar active-filter or fixed-gain stages on one board when each channel operates within the same bandwidth and stability limits. Its 2.2 MHz gain-bandwidth product provides useful closed-loop bandwidth for audio-range and instrumentation filters, and the 1 V/us slew rate limits large-signal distortion. Keep the feedback network close to the amplifier and follow the manufacturer stability guidance for capacitive loading. Rail-to-rail input and output capability is especially helpful when the filter must accept or generate signals near the low supply rails.
מומלץ
Current-to-Voltage Conversion
The MC33204PG is useful in current-measurement front ends because its rail-to-rail inputs accept the voltage generated by a shunt or current-feedback network with minimal wasted signal range. Four channels allow a design to monitor several currents when their gain and bandwidth requirements are similar. The 2.2 MHz gain-bandwidth product supports shunt-amplifier bandwidths common in laboratory and industrial control equipment, while the 1 V/us slew rate provides useful dynamic range for rapidly changing current waveforms. Compensation must account for the shunt and feedback parasitic capacitance.
מומלץ
Audio Preamp and Summing Stages
The MC33204PG can serve as a quad low-voltage audio preamp when the design requires input and output headroom close to the operating rails. Its rail-to-rail input stage accepts small microphone-level or line-level signals, and the rail-to-rail output reduces distortion when the signal approaches the available output range. The 2.2 MHz gain-bandwidth product exceeds the bandwidth of many audio-band signal paths, while the 1 V/us slew rate supports moderate output amplitudes. Confirm output-current limits, noise performance, and the maximum input signal before setting closed-loop gain.
מומלץ
Industrial Control and Data Acquisition
The MC33204PG is appropriate for industrial interface boards requiring several low-voltage amplifier channels without allocating a separate package for each signal. Rail-to-rail inputs help accommodate outputs from sensors and control converters operating close to 5 V or 3.3 V rails, while the output stage can drive downstream ADC drivers within its current capability. Its general-purpose 2.2 MHz bandwidth suits slow process-control, transducer, and monitoring loops rather than high-speed data capture. Protection, grounding, and isolation requirements determine how closely the amplifier should be placed to the field wiring.
מומלץ
Joystick, Touch, and Position Interfaces
The MC33204PG can buffer resistive, capacitive, or position-sensing inputs that operate on low-voltage rails. Rail-to-rail inputs preserve signal amplitude at the ends of the sensor's travel, and the output stage can present the conditioned level to a controller or comparator. Four channels are useful when a system combines multiple analog controls, and the 2.2 MHz gain-bandwidth product is adequate for many human-interface and low-frequency position systems. Check input capacitance, sensor drive requirements, and any filtering needed to reject switching or display noise.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור MC33204PG — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | MC33204P |
|---|---|---|
| Brand | onsemi | onsemi |
| Package | 14-pin PDIP | 14-pin PDIP - same |
| Number of Amplifiers | 4 | 4 |
| Supply Voltage Range | 1.8 V to 12 V | 1.8 V to 12 V |
| Input Common-Mode Range | Rail-to-rail | Rail-to-rail |
| Output Swing | Rail-to-rail, within approximately 50 mV of each rail | Rail-to-rail, within approximately 50 mV of each rail |
| Gain-Bandwidth Product | 2.2 MHz | 2.2 MHz |
| Slew Rate | 1 V/us | 1 V/us |
| Input Overdrive Tolerance | Approximately 200 mV beyond the supply rails without phase reversal | Approximately 200 mV beyond the supply rails without phase reversal |
מבדילים עיקריים
- Four rail-to-rail amplifiers in one through-hole package (לעומתMC33204P)
- Usable signal headroom from low-voltage supplies (לעומתMC33204P)
- Input overdrive behavior for sensor interfaces (לעומתMC33204P)
הערות תכנון
Keep the MC33204 supply within the 1.8 V to 12 V device range and account for rail-to-rail output headroom at the lowest operating supply. Place bypass capacitors close to the V+ and V- pins with short, low-inductance connections. When the amplifier sources current near its limit, verify the output-current capability and dissipation in the manufacturer characteristic curves rather than assuming full rail-to-rail swing under load.
Rail-to-rail input operation does not make the amplifier immune to supply-referenced overvoltage. Although the inputs tolerate approximately 200 mV beyond the rails, sustained large excursions can damage internal input structures. In exposed systems, use series resistance, clamping devices, or an appropriate protection network. Also avoid assuming that a 14-pin quad amplifier from another family is interchangeable solely because its package has 14 leads.
Route the sensitive input and feedback nodes as short as possible, keep the feedback components close to the amplifier, and maintain a continuous ground plane beneath the circuit. Place the supply bypass network at the power pins and separate it from high-current switching paths. When driving capacitive loads, use an isolation resistor or an output-buffer arrangement if the load can exceed the device's stable operating region.
מידע על תאימות
The onsemi product page identifies MC33204 as a standard operational amplifier product. No explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals statement was available for this orderable MPN, so those fields remain unknown. AEC-Q100 qualification is not applicable to this general-purpose commercial amplifier.