MC3486NE4 - Quad Differential Line Receiver | Texas Instruments
MPN: MC3486NE4 ✓ সক্রিয়MC3486NE4 সারাংশ
A differential line receiver converts the voltage difference between two conductors into a conventional logic-level output. This receiver belongs to the line-driver and line-receiver hierarchy, within interface ICs and data-communication ICs. Differential signaling improves common-mode-noise rejection and allows data to be transmitted reliably over longer cable runs than a single-ended interface. The MC3486NE4 implements four such channels in one package, reducing component count in multi-channel industrial, communications, and data-processing equipment.
The principal features include four independent differential receivers, TTL-compatible outputs, 3-state operation for bus-oriented connection, and compatibility with ANSI TIA/EIA-422-B, ANSI TIA/EIA-423-B, ITU V.10, and ITU V.11 interface standards. Its through-hole 16-pin DIP construction supports conventional PCB assembly and repair. The MC3486NE4 suffix identifies the commercial-temperature, plastic-DIP ordering configuration, although individual electrical limits should be confirmed against the manufacturer datasheet for the operating conditions of the finished design.
In a typical interface, a remote transmitter sends balanced data into a twisted pair, and the MC3486NE4 detects the differential voltage to produce a logic output for a UART, microprocessor, programmable logic, or other digital controller. Because each receiver is independent, four unrelated channels can be decoded in parallel. The 3-state output feature also permits a receiver output to be disconnected when multiple devices share a bus, provided the control and pull-up arrangements follow the system design requirements.
Typical applications include industrial control links, instrumentation interfaces, peripheral data links, telecommunications equipment, and legacy computer peripherals. The device is especially relevant where a modern controller must connect to an RS-422 or RS-423 interface while minimizing the number of receiver packages. Its four-channel architecture can also simplify multi-axis positioning, test systems, and distributed control networks that carry several low-speed differential signals.
Designers should verify input voltage limits, common-mode range, propagation delay, enable timing, output drive capability, and temperature limits against the manufacturer datasheet before finalizing the interface. Decoupling and signal-return paths should be arranged to prevent fast digital edges and cable transients from coupling into adjacent channels. Through-hole construction provides mechanical robustness, but the PCB must preserve the exact pin orientation and provide adequate clearance for the receiver's through-hole leads.
This page organizes the manufacturer interface standards, package information, sourcing details, candidate replacements, and practical selection guidance for engineers evaluating the MC3486NE4. Cross-references are presented as design aids and should be checked against the complete pinout, timing characteristics, logic states, and environmental limits before a substitution is approved.
এর জন্য ড্রপ-ইন বিকল্প MC3486NE4 — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।
এই সিরিজের ভ্যারিয়েন্ট
একই সিরিজের মডেল যেগুলো drop-in compatible MC3486NE4 (একই form factor এবং footprint) — পার্থক্য রয়েছে Package, Output State, Supported Standards.
MC3486N
✅ ড্রপ-ইনমূল্যের জন্য যোগাযোগ করুন
ডেটাশিট দেখুন →MC3486NG4
✅ ড্রপ-ইনমূল্যের জন্য যোগাযোগ করুন
ডেটাশিট দেখুন →DS3486N
✅ ড্রপ-ইন📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
HD75173P
✅ ড্রপ-ইন📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
MC3486NE4 বিশেষণ
| Receiver Configuration | 4 independent differential line receivers |
| Number of Differential Input Pairs | 4 pairs |
| Output Logic Compatibility | TTL-compatible |
| Output States | 3-state including high-impedance |
| Input Interface | Differential |
| RS-422 Compatibility | ANSI TIA/EIA-422-B |
| RS-423 Compatibility | ANSI TIA/EIA-423-B |
| ITU Compatibility | V.10 and V.11 |
| প্যাকেজ | 16-pin DIP |
| Terminal Count | 16 terminals |
| মাউন্টিং টাইপ | Through-hole |
| Package Shape | Rectangular |
| Temperature Grade | Commercial |
MC3486NE4 rectangular পিন কনফিগারেশন গাইড
MC3486NE4 (rectangular প্যাকেজ)-এর পিন কনফিগারেশন। পিন নম্বরিং, ফাংশন এবং সংযোগ ডায়াগ্রাম প্রস্তুতকারকের ডেটাশিটে সংজ্ঞায়িত করা আছে। সঠিক ফুটপ্রিন্ট এবং সোল্ডারিং নির্দেশিকার জন্য এটি দেখুন।
এর জন্য বিস্তারিত পিনআউট ডেটা পাওয়া যায়নি MC3486NE4.
দেখুন ডেটাশিট সম্পূর্ণ পিন কনফিগারেশনের জন্য।
সাধারণ ব্যবহার
MC3486NE4 এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Industrial Control Data Links, Instrumentation and Test Systems, Telecommunications Equipment Interfaces, Computer Peripherals and Legacy Data Links, Multi-Axis Positioning Interfaces, Distributed Control Networks.
Industrial Control Data Links
The MC3486NE4 is suitable for industrial control equipment that receives several low-speed differential data signals from field equipment or a remote controller. Its four independent differential receivers can recover TTL-compatible logic levels in a single 16-pin DIP package, while the manufacturer datasheet identifies ANSI TIA/EIA-422-B and TIA/EIA-423-B compatibility. The 3-state outputs can support bus-oriented arrangements when the system provides the required biasing and a verified control sequence. Keep each differential pair routed as a controlled impedance path, maintain a continuous return route, and confirm common-mode range, propagation delay, and enable timing in the electrical tables.
সুপারিশকৃত
Instrumentation and Test Systems
The MC3486NE4 can receive four differential command or status channels in instrumentation, test, and measurement systems where a controller must communicate over balanced wiring. The four-channel arrangement reduces the number of receiver packages compared with discrete single-channel solutions, while TTL-compatible outputs connect naturally to digital control logic. The 16-pin through-hole package also suits legacy or serviceable test hardware. When applying the receiver, verify the permitted common-mode range at the longest cable length, place input protection away from the IC pins when needed, and use the manufacturer timing limits to establish sampling margins around incoming data edges.
সুপারিশকৃত
Telecommunications Equipment Interfaces
The MC3486NE4 is appropriate for telecommunications or data-communication equipment that needs multiple balanced receive channels. According to the manufacturer datasheet, the receiver supports ANSI TIA/EIA-422-B, ANSI TIA/EIA-423-B, and ITU V.10 and V.11 interfaces, making it suitable for established differential-interface designs. The four independent channels can handle separate control, status, or data signals, and the 3-state outputs permit bus participation when the system architecture requires it. Check propagation delay against the target bit rate, preserve pair symmetry through connector and cable transitions, and confirm supply and temperature limits from the device specification.
সুপারিশকৃত
Computer Peripherals and Legacy Data Links
The MC3486NE4 can be used in computer peripherals and legacy data-link equipment that still relies on balanced differential signaling. Its TTL-compatible outputs provide a straightforward interface between the recovered logic signals and a microprocessor, UART, or other controller, while the four receivers support parallel control functions in one package. The through-hole DIP construction is useful for repairable boards and industrial equipment with long service lives. Confirm that the legacy interface uses a voltage arrangement covered by the receiver's input limits, and account for the MC3486 enable and output timing before connecting a channel to a shared bus.
সুপারিশকৃত
Multi-Axis Positioning Interfaces
The MC3486NE4 can support multi-axis positioning equipment by receiving differential position, limit, or drive-status signals through four independent channels. Consolidating these signals into one receiver package simplifies the interface between a motion controller and external axis electronics. The 3-state outputs may also assist bus-oriented control schemes, provided pull-up or pull-down components and enable sequencing are designed correctly. The receiver's TTL-compatible output can connect to a digital controller after the differential signal has been recovered. Use the manufacturer propagation-delay and enable-timing limits to set control timing, and validate common-mode margin at each axis cable length.
সুপারিশকৃত
Distributed Control Networks
The MC3486NE4 is useful in distributed control systems where remote nodes send multiple differential signals back to a central controller. Its four independent receivers combine several data or acknowledgment channels without requiring four separate IC packages, and the documented TIA/EIA-422-B, TIA/EIA-423-B, ITU V.10, and ITU V.11 support covers several established interface conventions. Use matched routing for each differential pair, provide a suitable ground or return strategy as required by the installation, and isolate the receiver from cable transients when the installation environment introduces surge exposure. Validate all signal thresholds and timing at the intended temperature and supply voltage.
সুপারিশকৃত
সুপারিশকৃত পণ্যের সারসংক্ষেপ
এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা MC3486NE4 — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।
নির্বাচন গাইড
বিকল্পের সাথে তুলনা
| পারামিটার | এই পণ্য | MC3486N | MC3486NG4 | DS3486N | HD75173P |
|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | National Semiconductor | Renesas Electronics |
| Package | 16-pin DIP | 16-pin DIP | 16-pin DIP | 16-pin DIP | 16-pin DIP |
| Receiver Channels | 4 differential receivers | 4 differential receivers | 4 differential receivers | 4 differential receivers | 4 differential receivers |
মূল পার্থক্যসমূহ
- Four differential channels in one receiver package (বনামHD75173P)
- Documented support for four interface conventions (বনামDS3486N)
- Three-state TTL-compatible outputs (বনামMC3486N)
ডিজাইন নোট
Route each differential input as a controlled pair with consistent spacing and impedance. Avoid sharing a return-current path with noisy switching nodes, and minimize stub branches between the connector, protection components, and MC3486NE4 inputs. Confirm the receiver's common-mode range and differential thresholds against the worst-case cable voltage, ground offset, noise, and surge conditions before treating the interface as compliant.
Do not infer enable polarity, input limits, or bus timing from the term 3-state alone. Use the MC3486 manufacturer datasheet to identify the active logic level, disable time, output leakage, and input thresholds. A high-impedance output does not remove the need for suitable bias resistors, and it must not be used to hold a wired-OR bus at a valid logic level without a deliberate pull-up or pull-down arrangement.
Use a 16-pin through-hole DIP footprint with the physical pin-1 orientation verified against the package drawing. Maintain adequate clearance between adjacent input pairs and keep sensitive receive traces away from transformer windings, relay contacts, clock lines, and high-current switching paths. If the board is wave-soldered, inspect the underside for solder bridges and confirm that no receiver output is driven by two external devices at the same time.
The MC3486NE4, MC3486N, and MC3486NG4 are not automatically interchangeable in every BOM because suffix codes can represent different package, temperature, or qualification conditions. Perform a line-by-line comparison of the ordering table, pin functions, electrical characteristics, and environmental limits. For a direct substitution, preserve the same 16-pin footprint and verify that supply voltage, logic thresholds, enable behavior, propagation delay, and temperature coverage are equivalent.
কমপ্লায়েন্স তথ্য
The manufacturer datasheet identifies ANSI TIA/EIA-422-B, ANSI TIA/EIA-423-B, ITU V.10, and ITU V.11 interface standards. Material-compliance declarations were not identified and are recorded as unknown.