MCP3422A7-E/MC - 18-Bit Dual-Input ADC | Microchip Technology
MPN: MCP3422A7-E/MC ✓ সক্রিয়MCP3422A7-E/MC সারাংশ
A delta-sigma ADC is a voltage-to-digital converter category that uses oversampling, noise shaping, and digital filtering to obtain high resolution from low-resolution internal converters. The MCP3422 belongs to the broader ADC, data-converter, and semiconductor hierarchy. Its differential architecture is useful when the measured signal is centered around a bias voltage, while its low-noise design supports precision instrumentation, industrial measurement, and sensor acquisition systems.
The principal features include resolution up to 18 bits, two differential input channels, a 3.75 Hz conversion rate for this configuration, and a programmable gain amplifier. The converter uses a 2.048 V on-board precision reference and communicates through a two-wire I2C-compatible serial interface. A single supply range of 2.7 V to 5.5 V allows the device to operate in both 3.3 V and 5 V systems.
Delta-sigma conversion trades conversion speed for resolution and noise performance. The MCP3422 family is therefore most appropriate for slowly changing sensor signals, process-control variables, temperature measurements, pressure readings, and low-bandwidth instrumentation rather than high-rate waveform acquisition. Differential inputs can reduce common-mode noise when the source is balanced and both signal wires have similar impedances and layout symmetry.
Typical applications include industrial process monitoring, bridge-sensor and pressure-sensor interfaces, battery monitoring, laboratory measurement equipment, environmental sensing, and low-rate data acquisition. The integrated 2.048 V reference provides a convenient full-scale basis for differential measurements, while the PGA allows the analog front end to accommodate signals closer to the differential input range.
PCB implementation requires careful attention to analog grounding, supply bypassing, and differential routing. Place the decoupling capacitor close to the supply and ground pins, keep the analog input traces short, and route the two inputs as a matched pair. A common ground reference and balanced source impedance help preserve the common-mode rejection and noise advantages inherent to the differential converter.
This product page combines the MCP3422A7-E/MC specifications, verified manufacturer information, family-level drop-in alternatives, and practical PCB guidance. It supports faster part selection by distinguishing protocol, package, channel-count, resolution, and conversion-rate considerations while keeping the final component decision grounded in the manufacturer documentation.
এর জন্য ড্রপ-ইন বিকল্প MCP3422A7-E/MC — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।
এই সিরিজের ভ্যারিয়েন্ট
একই সিরিজের মডেল যেগুলো drop-in compatible MCP3422A7-E/MC (একই form factor এবং footprint) — পার্থক্য রয়েছে Conversion Rate, Differential Input Range, Package, Resolution.
MCP3422A4T-E/MC
✅ ড্রপ-ইন📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
MCP3422A0T-E/MC
✅ ড্রপ-ইন ⚠️ স্পেক যাচাইকৃত নয়📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
MCP3422A1T-E/MC
✅ ড্রপ-ইন ⚠️ স্পেক যাচাইকৃত নয়📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
MCP3422A2T-E/MC
✅ ড্রপ-ইন ⚠️ স্পেক যাচাইকৃত নয়📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
MCP3422A6T-E/MC
✅ ড্রপ-ইন ⚠️ স্পেক যাচাইকৃত নয়📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
MCP3422A7-E/MC সর্বোচ্চ রেটিং ও বৈদ্যুতিক বৈশিষ্ট্য
| রেজোলিউশন | 18 bits |
| Input Channels | 2 differential inputs |
| ADC Architecture | Delta-sigma |
| Conversion Rate | 3.75 samples/s |
| Supply Voltage Range | 2.7 V to 5.5 V |
| Internal Reference Voltage | 2.048 V |
| Differential Input Range | +/-2.048 V with internal reference |
| Programmable Gain Amplifier | Integrated PGA |
| Serial Interface | Two-wire I2C-compatible |
| প্যাকেজ | 8-pin DFN, 2 x 3 mm |
| মাউন্টিং টাইপ | Surface mount |
| Automotive Qualification | Automotive |
| RoHS স্ট্যাটাস | RoHS |
MCP3422A7-E/MC 8-pin dfn, 2 x 3 mm পিন কনফিগারেশন গাইড
MCP3422A7-E/MC (8-pin dfn, 2 x 3 mm প্যাকেজ)-এর পিন কনফিগারেশন। এই অ্যানালগ কম্পোনেন্টে ইনপুট, আউটপুট ও পাওয়ার সাপ্লাই পিন রয়েছে। অফসেট নাল, কম্পেনসেশন ও এনেবল পিন কনফিগারেশনের জন্য প্রস্তুতকারকের ডেটাশিট দেখুন। সিগন্যাল কন্ডিশনিং ও অ্যামপ্লিফায়ার সার্কিটের জন্য আদর্শ।
এর জন্য বিস্তারিত পিনআউট ডেটা পাওয়া যায়নি MCP3422A7-E/MC.
দেখুন ডেটাশিট সম্পূর্ণ পিন কনফিগারেশনের জন্য।
সাধারণ ব্যবহার
MCP3422A7-E/MC এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Industrial Pressure Sensor Interface, Temperature and Thermocouple Monitoring, Battery Cell Monitoring, Process-Control Instrumentation, Environmental Data Acquisition, Laboratory Precision Measurement.
Industrial Pressure Sensor Interface
The MCP3422A7-E/MC fits bridge-based pressure sensing because it combines 18-bit resolution with two differential inputs and an integrated programmable gain amplifier. The 2.048 V internal reference establishes a stable conversion basis, while differential sampling helps reject common-mode voltage present on industrial sensor lines. Its 3.75 samples/s rate is appropriate for slowly changing pressure and can be filtered for a stable process-control reading. Place the converter close to the sensor or bridge excitation network, use matched input routing, and provide local supply bypassing. The principal trade-off is throughput: pressure loops that require hundreds of samples per second should use a faster converter.
সুপারিশকৃত
Temperature and Thermocouple Monitoring
The MCP3422A7-E/MC can acquire slowly changing temperature signals at 18-bit resolution while operating from a 2.7 V to 5.5 V supply. Differential inputs allow a low-level sensor voltage to be measured relative to a biased return rather than directly to ground, improving common-mode immunity in longer cable runs. The integrated 2.048 V reference supports consistent conversion scaling, while the programmable gain amplifier can accommodate small sensor outputs. A 3.75 samples/s conversion rate is more than adequate for thermal monitoring. The primary design concern is thermocouple polarity and cold-junction compensation, which must be implemented correctly in the analog and digital system.
সুপারিশকৃত
Battery Cell Monitoring
The MCP3422A7-E/MC is appropriate for slow battery-cell voltage acquisition where energy efficiency and measurement resolution matter more than high conversion throughput. Its 2.7 V to 5.5 V supply range supports common embedded supply rails, and the two differential inputs can monitor a cell or differential element without requiring separate single-ended channels. The 18-bit conversion resolution supports fine voltage resolution, while the internal 2.048 V reference provides a controlled measurement basis. Designers should verify the actual input range, PGA configuration, and absolute accuracy at the operating temperature. Cell balancing and high-current protection remain separate functions and must not be placed in the precision ADC signal path.
সুপারিশকৃত
Process-Control Instrumentation
The MCP3422A7-E/MC supports process-control modules that monitor slow variables such as level, flow, or differential pressure. Its differential inputs are valuable when the transmitter produces a signal centered around a midpoint or includes significant common-mode noise. The 18-bit resolution and programmable gain amplifier improve use of the converter's dynamic range, while the 2.048 V reference simplifies calibration. At 3.75 samples/s, the device works well for supervisory measurements rather than high-speed closed-loop dynamics. For reliable industrial operation, isolate ground currents from the analog return path, use a stable supply, and follow the manufacturer layout guidance for the exposed pad and input filtering.
সুপারিশকৃত
Environmental Data Acquisition
The MCP3422A7-E/MC can digitize slow environmental measurements such as humidity, carbon dioxide concentration, soil moisture, and ambient light when the sensor output is differential or referenced to a bias. Its low-noise delta-sigma architecture is well matched to signals that do not require millisecond-level sampling. The integrated 2.048 V reference and programmable gain amplifier help preserve resolution across different sensor ranges. Use matched input traces, shielded or guarded sensor connections, and filtering at the analog inputs to reject environmental electrical noise. The 3.75 samples/s rate should be included in the sensor's settling-time calculation, especially for thermal humidity sensors that require a long response time.
সুপারিশকৃত
Laboratory Precision Measurement
The MCP3422A7-E/MC suits laboratory instruments that measure low-level differential voltages with limited acquisition bandwidth. Its 18-bit resolution, integrated precision reference, and programmable gain amplifier provide a compact measurement front end without requiring a separate reference device. The two-wire I2C-compatible interface simplifies connection to a controller, while the small DFN package supports dense instrument boards. A 3.75 samples/s conversion rate allows time for digital filtering and is appropriate for calibrated DC measurements. Designers should account for input bias current, source impedance, reference accuracy, and the acquisition settling period in the calibration procedure, and should route analog and digital return currents to minimize measurement perturbations.
সুপারিশকৃত
সুপারিশকৃত পণ্যের সারসংক্ষেপ
এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা MCP3422A7-E/MC — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।
নির্বাচন গাইড
বিকল্পের সাথে তুলনা
| পারামিটার | এই পণ্য | MCP3422A4T-E/MC | MCP3422A0T-E/MC | MCP3422A1T-E/MC | MCP3422A2T-E/MC | MCP3422A6T-E/MC |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 8-DFN (2x3) | 8-DFN (2x3) | 8-DFN (2x3) | 8-DFN (2x3) | 8-DFN (2x3) | 8-DFN (2x3) |
| Resolution | 18 bits | 18 bits | 18 bits | 18 bits | 18 bits | 18 bits |
| Input Channels | 2 differential inputs | 2 differential inputs | 2 differential inputs | 2 differential inputs | 2 differential inputs | 2 differential inputs |
| Supply Voltage Range | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V |
| Internal Reference | 2.048 V precision reference | 2.048 V precision reference | 2.048 V precision reference | 2.048 V precision reference | 2.048 V precision reference | 2.048 V precision reference |
| Serial Interface | Two-wire I2C-compatible | Two-wire I2C-compatible | Two-wire I2C-compatible | Two-wire I2C-compatible | Two-wire I2C-compatible | Two-wire I2C-compatible |
| Programmable Gain Amplifier | Integrated PGA | Integrated PGA | Integrated PGA | Integrated PGA | Integrated PGA | Integrated PGA |
| Differential Input Range | +/-2.048 V with internal reference | +/-2.048 V with internal reference | +/-2.048 V with internal reference | +/-2.048 V with internal reference | +/-2.048 V with internal reference | +/-2.048 V with internal reference |
মূল পার্থক্যসমূহ
- Conversion option selected for 3.75 samples/s operation (বনামMCP3422A4T-E/MC)
- Compact differential measurement front end (বনামMCP3422A0T-E/MC)
- No separate precision reference required (বনামMCP3422A1T-E/MC)
- Single-supply operation with integrated PGA (বনামMCP3422A2T-E/MC)
ডিজাইন নোট
Route the two differential inputs as a matched pair, keep both traces short, and avoid switching nodes beneath the analog inputs. Terminate the source network so the impedances seen by both inputs remain similar. This preserves common-mode rejection and reduces conversion error caused by unequal settling. Use a quiet analog return and keep digital interface current away from the reference and input ground paths.
Place the supply bypass capacitor immediately beside the converter's supply and ground pins, with a short and low-inductance connection. Keep the analog and digital grounds joined at a controlled location near the device or power-entry point. The MCP3422A7-E/MC accepts 2.7 V to 5.5 V, but the selected rail must remain within that range during startup, transient, and fault conditions.
Do not treat the 18-bit nominal resolution as 18 bits of guaranteed absolute accuracy; reference error, offset, noise, input impedance, and conversion timing affect the usable result. Account for the 3.75 samples/s acquisition rate when setting sensor settling time or control-loop latency. For the 2 x 3 mm DFN package, implement the exposed-pad connection and land pattern exactly as shown in the manufacturer package drawing.
Add analog filtering close to the ADC pins when the sensor cable can pick up high-frequency interference. Choose filter capacitors and resistors that preserve the required settling time at the selected PGA gain and conversion rate. Differential filtering components should be closely matched. If a front-end op-amp drives the converter, verify its settling behavior for the selected gain rather than relying only on its small-signal bandwidth.
কমপ্লায়েন্স তথ্য
The product listing identifies the MCP3422A7-E/MC as RoHS. The automotive designation appears in the family listing, but no separate AEC-Q100 qualification statement, lead-free statement, halogen-free statement, or conflict-minerals statement is provided.