Microchip Technology

MCP3422A7-E/MC - 18-Bit Dual-Input ADC | Microchip Technology

N.º da peça: MCP3422A7-E/MC ✓ Ativo
2.7 V to 5.5 V Vdss 8-pin DFN, 2 x 3 mm Package
MOQ: 1 |

MCP3422A7-E/MC Visão geral

The Microchip Technology MCP3422A7-E/MC is an 18-bit, dual-input delta-sigma analog-to-digital converter with differential inputs, an integrated precision 2.048 V reference, and a two-wire I2C-compatible interface. It operates from a single 2.7 V to 5.5 V supply and is packaged in an 8-pin DFN measuring 2 x 3 mm. The MCP3422A7-E/MC supports a differential input range of plus or minus 2.048 V with its internal reference.

A delta-sigma ADC is a voltage-to-digital converter category that uses oversampling, noise shaping, and digital filtering to obtain high resolution from low-resolution internal converters. The MCP3422 belongs to the broader ADC, data-converter, and semiconductor hierarchy. Its differential architecture is useful when the measured signal is centered around a bias voltage, while its low-noise design supports precision instrumentation, industrial measurement, and sensor acquisition systems.

The principal features include resolution up to 18 bits, two differential input channels, a 3.75 Hz conversion rate for this configuration, and a programmable gain amplifier. The converter uses a 2.048 V on-board precision reference and communicates through a two-wire I2C-compatible serial interface. A single supply range of 2.7 V to 5.5 V allows the device to operate in both 3.3 V and 5 V systems.

Delta-sigma conversion trades conversion speed for resolution and noise performance. The MCP3422 family is therefore most appropriate for slowly changing sensor signals, process-control variables, temperature measurements, pressure readings, and low-bandwidth instrumentation rather than high-rate waveform acquisition. Differential inputs can reduce common-mode noise when the source is balanced and both signal wires have similar impedances and layout symmetry.

Typical applications include industrial process monitoring, bridge-sensor and pressure-sensor interfaces, battery monitoring, laboratory measurement equipment, environmental sensing, and low-rate data acquisition. The integrated 2.048 V reference provides a convenient full-scale basis for differential measurements, while the PGA allows the analog front end to accommodate signals closer to the differential input range.

PCB implementation requires careful attention to analog grounding, supply bypassing, and differential routing. Place the decoupling capacitor close to the supply and ground pins, keep the analog input traces short, and route the two inputs as a matched pair. A common ground reference and balanced source impedance help preserve the common-mode rejection and noise advantages inherent to the differential converter.

This product page combines the MCP3422A7-E/MC specifications, verified manufacturer information, family-level drop-in alternatives, and practical PCB guidance. It supports faster part selection by distinguishing protocol, package, channel-count, resolution, and conversion-rate considerations while keeping the final component decision grounded in the manufacturer documentation.

Alternativas drop-in para MCP3422A7-E/MC — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.

Variantes desta série

Modelos da mesma série compatíveis como drop-in com MCP3422A7-E/MC (mesmo formato e footprint) — diferindo em Conversion Rate, Differential Input Range, Package, Resolution.

Microchip Technology
Conversion Rate: 4 samples/s
Differential Input Range: ±2.048 V
Package: 8-DFN, 2x3 mm

MCP3422A4T-E/MC

✅ Drop-In
📦 8-DFN (2x3)
Resolution remains 18 bits (0% difference) and the package and terminals are consistent; the family conversion-rate option differs, with 3.75 samples/s for MCP3422A7-E/MC and the A4 suffix indicating a different rate option

📋 Alternativa de referência (fora do catálogo)

MCP3422A0T-E/MC

✅ Drop-In ⚠️ Especificações não verificadas
📦 8-DFN (2x3)
Resolution remains 18 bits (0% difference) and the MCP3422 family supply and interface architecture are retained; the A0 conversion-rate option differs from the 3.75 samples/s A7 option

📋 Alternativa de referência (fora do catálogo)

MCP3422A1T-E/MC

✅ Drop-In ⚠️ Especificações não verificadas
📦 8-DFN (2x3)
Resolution remains 18 bits (0% difference) with the same MCP3422 differential-input architecture; the A1 conversion-rate option differs from the 3.75 samples/s A7 option

📋 Alternativa de referência (fora do catálogo)

MCP3422A2T-E/MC

✅ Drop-In ⚠️ Especificações não verificadas
📦 8-DFN (2x3)
Resolution remains 18 bits (0% difference) with the same MCP3422 differential-input architecture; the A2 conversion-rate option differs from the 3.75 samples/s A7 option

📋 Alternativa de referência (fora do catálogo)

MCP3422A6T-E/MC

✅ Drop-In ⚠️ Especificações não verificadas
📦 8-DFN (2x3)
Resolution remains 18 bits (0% difference) with the same MCP3422 differential-input architecture; the A6 conversion-rate option differs from the 3.75 samples/s A7 option

📋 Alternativa de referência (fora do catálogo)

MCP3422A7-E/MC Classificações máximas e características elétricas

Resolução 18 bits
Input Channels 2 differential inputs
ADC Architecture Delta-sigma
Conversion Rate 3.75 samples/s
Supply Voltage Range 2.7 V to 5.5 V
Internal Reference Voltage 2.048 V
Differential Input Range +/-2.048 V with internal reference
Programmable Gain Amplifier Integrated PGA
Serial Interface Two-wire I2C-compatible
Encapsulamento 8-pin DFN, 2 x 3 mm
Tipo de montagem Surface mount
Automotive Qualification Automotive
Status RoHS RoHS

Guia de Configuração de Pinos do MCP3422A7-E/MC 8-pin dfn, 2 x 3 mm

Configuração de pinos para MCP3422A7-E/MC (pacote 8-pin dfn, 2 x 3 mm). Este componente analógico possui pinos de entrada, saída e alimentação. Consulte o datasheet do fabricante para configurações de offset null, compensação e pino de enable. Ideal para circuitos de condicionamento de sinal e amplificadores.

Diagrama de pinagem do pacote 8-pin dfn, 2 x 3 mm para MCP3422A7-E/MC

Nenhum dado detalhado de pinagem disponível para MCP3422A7-E/MC.

Consulte a ficha técnica para a configuração completa dos pinos.

Aplicações típicas

MCP3422A7-E/MC é adequado para 6 aplicaçãos: Industrial Pressure Sensor Interface, Temperature and Thermocouple Monitoring, Battery Cell Monitoring, Process-Control Instrumentation, Environmental Data Acquisition, Laboratory Precision Measurement.

🏭

Industrial Pressure Sensor Interface

The MCP3422A7-E/MC fits bridge-based pressure sensing because it combines 18-bit resolution with two differential inputs and an integrated programmable gain amplifier. The 2.048 V internal reference establishes a stable conversion basis, while differential sampling helps reject common-mode voltage present on industrial sensor lines. Its 3.75 samples/s rate is appropriate for slowly changing pressure and can be filtered for a stable process-control reading. Place the converter close to the sensor or bridge excitation network, use matched input routing, and provide local supply bypassing. The principal trade-off is throughput: pressure loops that require hundreds of samples per second should use a faster converter.

🌡️

Temperature and Thermocouple Monitoring

The MCP3422A7-E/MC can acquire slowly changing temperature signals at 18-bit resolution while operating from a 2.7 V to 5.5 V supply. Differential inputs allow a low-level sensor voltage to be measured relative to a biased return rather than directly to ground, improving common-mode immunity in longer cable runs. The integrated 2.048 V reference supports consistent conversion scaling, while the programmable gain amplifier can accommodate small sensor outputs. A 3.75 samples/s conversion rate is more than adequate for thermal monitoring. The primary design concern is thermocouple polarity and cold-junction compensation, which must be implemented correctly in the analog and digital system.

⚡

Battery Cell Monitoring

The MCP3422A7-E/MC is appropriate for slow battery-cell voltage acquisition where energy efficiency and measurement resolution matter more than high conversion throughput. Its 2.7 V to 5.5 V supply range supports common embedded supply rails, and the two differential inputs can monitor a cell or differential element without requiring separate single-ended channels. The 18-bit conversion resolution supports fine voltage resolution, while the internal 2.048 V reference provides a controlled measurement basis. Designers should verify the actual input range, PGA configuration, and absolute accuracy at the operating temperature. Cell balancing and high-current protection remain separate functions and must not be placed in the precision ADC signal path.

⚙️

Process-Control Instrumentation

The MCP3422A7-E/MC supports process-control modules that monitor slow variables such as level, flow, or differential pressure. Its differential inputs are valuable when the transmitter produces a signal centered around a midpoint or includes significant common-mode noise. The 18-bit resolution and programmable gain amplifier improve use of the converter's dynamic range, while the 2.048 V reference simplifies calibration. At 3.75 samples/s, the device works well for supervisory measurements rather than high-speed closed-loop dynamics. For reliable industrial operation, isolate ground currents from the analog return path, use a stable supply, and follow the manufacturer layout guidance for the exposed pad and input filtering.

🧩

Environmental Data Acquisition

The MCP3422A7-E/MC can digitize slow environmental measurements such as humidity, carbon dioxide concentration, soil moisture, and ambient light when the sensor output is differential or referenced to a bias. Its low-noise delta-sigma architecture is well matched to signals that do not require millisecond-level sampling. The integrated 2.048 V reference and programmable gain amplifier help preserve resolution across different sensor ranges. Use matched input traces, shielded or guarded sensor connections, and filtering at the analog inputs to reject environmental electrical noise. The 3.75 samples/s rate should be included in the sensor's settling-time calculation, especially for thermal humidity sensors that require a long response time.

🧪

Laboratory Precision Measurement

The MCP3422A7-E/MC suits laboratory instruments that measure low-level differential voltages with limited acquisition bandwidth. Its 18-bit resolution, integrated precision reference, and programmable gain amplifier provide a compact measurement front end without requiring a separate reference device. The two-wire I2C-compatible interface simplifies connection to a controller, while the small DFN package supports dense instrument boards. A 3.75 samples/s conversion rate allows time for digital filtering and is appropriate for calibrated DC measurements. Designers should account for input bias current, source impedance, reference accuracy, and the acquisition settling period in the calibration procedure, and should route analog and digital return currents to minimize measurement perturbations.

What is the MCP3422A7-E/MC?
The MCP3422A7-E/MC is a Microchip Technology 18-bit, dual-input delta-sigma ADC with differential inputs, an integrated 2.048 V precision reference, a programmable gain amplifier, and a two-wire I2C-compatible interface. According to the manufacturer product page, it operates from a single 2.7 V to 5.5 V supply and is housed in an 8-pin DFN package measuring 2 x 3 mm.
What are the key specifications of MCP3422A7-E/MC that engineers should know?
The MCP3422A7-E/MC combines 18-bit resolution, two differential inputs, delta-sigma conversion, a 3.75 samples/s conversion rate, and an integrated 2.048 V reference. The manufacturer identifies a 2.7 V to 5.5 V operating range and a two-wire I2C-compatible interface. Its 8-pin DFN package is only 2 x 3 mm, making the device suitable for compact precision-measurement instruments.
What is the input voltage range of MCP3422A7-E/MC?
The MCP3422A7-E/MC supports a differential input range of plus or minus 2.048 V when operated with its on-board 2.048 V precision reference. According to Microchip Technology, the differential input arrangement is intended for measuring signals centered around the selected reference or bias point. Exact headroom, common-mode limits, and gain-dependent input limits should be confirmed in the manufacturer datasheet.
How fast does the MCP3422A7-E/MC perform conversions?
The MCP3422A7-E/MC performs conversions at 3.75 samples/s in this A7 configuration. The manufacturer describes the MCP3422 as a low-noise, high-accuracy delta-sigma converter family, and the DigiKey listing identifies this part as a single-channel 18-bit converter with a 4 sps class of conversion speed. It is suited to slow sensor signals rather than high-rate waveform sampling.
What interface does MCP3422A7-E/MC use?
The MCP3422A7-E/MC uses a two-wire I2C-compatible serial interface for conversion data and device control. This reduces the number of signal connections compared with a parallel ADC and allows the converter to share a bus with other compatible peripherals. The address and register details should be taken from the manufacturer datasheet when designing the firmware and bus termination.
Where can I download the MCP3422A7-E/MC datasheet PDF?
The official MCP3422 documentation is available through the Microchip Technology MCP3422 product page at https://www.microchip.com/en-us/product/MCP3422. Select the datasheet or product documentation link for the authoritative electrical characteristics, pin descriptions, register map, and application information. The manufacturer page is preferable to third-party copies because it reflects the latest controlled documentation.
Where can I find the MCP3422A7-E/MC pinout?
Use the pin-description table and package drawing in the official MCP3422 manufacturer documentation to assign PCB functions. The MCP3422A7-E/MC uses an 8-pin DFN package measuring 2 x 3 mm, with differential analog inputs, power pins, ground, and I2C interface connections. The exposed-pad and thermal-land requirements must also be implemented according to the package drawing and layout guidance.
What can replace the MCP3422A7-E/MC?
The MCP3422A4T-E/MC is a documented family-level replacement candidate because the manufacturer comparison states that its terminal arrangement and package are consistent and that replacement does not require circuit modification. Other MCP3422A-series members can be evaluated as same-family options when their conversion-rate option is acceptable. Confirm the exact suffix, package, gain settings, and timing requirements before approving any substitution.
Is the MCP3422A7-E/MC suitable for industrial sensor measurement?
The MCP3422A7-E/MC is suitable for slow industrial sensor measurements requiring differential input accuracy and low noise. Its 18-bit resolution, integrated 2.048 V reference, and programmable gain amplifier suit pressure, temperature, and bridge-sensor interfaces, while differential routing helps reject common-mode noise. The 3.75 samples/s conversion rate limits throughput, so it is better for temperature or pressure than fast-moving control signals.
MCP3422A7-E/MC vs MCP3422A4T-E/MC - which is better for a sensor interface?
Choose the MCP3422A7-E/MC when its 3.75 samples/s conversion rate matches the required response time, and choose the MCP3422A4T-E/MC when its lower-rate configuration is sufficient. The manufacturer comparison describes the A4T part as a complete replacement with consistent terminals and packages. Both belong to the 18-bit MCP3422 family, so final selection should also consider noise, conversion timing, and software configuration.
When should I choose MCP3422A7-E/MC over another MCP3422 family member?
Choose the MCP3422A7-E/MC when the application needs a 3.75 samples/s conversion rate and can operate with an 8-pin DFN package. Choose a slower MCP3422 option when lower conversion throughput is acceptable and power or system timing constraints favor it. Because family members can differ in conversion-rate option, confirm register behavior and acquisition timing in the manufacturer documentation.
Can MCP3422A4T-E/MC replace MCP3422A7-E/MC without PCB changes?
Yes, the MCP3422A4T-E/MC can be considered as a pin-compatible replacement candidate according to the manufacturer comparison, which states that the terminals and packages are consistent and that replacement requires no existing-circuit modification. Both devices provide 18-bit conversion and use the MCP3422 family architecture. Firmware timing and the acceptable conversion-rate difference should still be reviewed.
What is the best Microchip Technology equivalent for MCP3422A7-E/MC?
The MCP3422A4T-E/MC is the best explicitly documented family-level equivalent found for the MCP3422A7-E/MC because it uses consistent terminals and packages and can replace the part without modifying the existing circuit. Other MCP3422A-series devices may provide different conversion-rate options. Choose the closest suffix after checking acquisition time, noise performance, and firmware expectations.
Where can I buy MCP3422A7-E/MC online and what is its price?
Use the Request a Quote form on this page to request the current MCP3422A7-E/MC unit price, stock position, minimum order quantity, and lead time. A current web listing shows a single-unit reference price, but the commercial offer should be confirmed through the quote workflow because inventory, volume, and sourcing conditions can change. The form connects the request with XAIPART without relying on static price text.
Is MCP3422A7-E/MC in stock and what is its lead time?
The MCP3422A7-E/MC is offered through a quote-based procurement workflow on this page, so submit a Request a Quote request for the current stock position and lead time. Lead time can vary with order quantity, package availability, and purchasing conditions. Avoid treating a distributor search result as a firm inventory commitment until the order is acknowledged.
How should differential inputs be routed for the MCP3422A7-E/MC?
Route the two differential inputs as a closely matched pair on the PCB, keep them short, and maintain similar impedances at the source. Place the supply bypass capacitor close to the power and ground pins, and use a quiet analog-ground path without carrying high-current return currents beneath the converter. The manufacturer application guidance should be followed for decoupling, grounding, and exposed-pad layout.
Is the MCP3422A7-E/MC RoHS compliant?
The MCP3422A7-E/MC is identified as RoHS in the product listing, indicating compliance with restrictions on hazardous substances for that catalog entry. The manufacturer product page identifies the automotive-oriented MCP3422 family, but the exact temperature grade, package marking, and certification documents should be checked against the ordering code. The device is also suitable for non-automotive industrial and instrumentation designs when its electrical ratings meet the system requirements.

Dados de referência de engenharia para MCP3422A7-E/MC — comparação, orientação de projeto e informações de conformidade.

Guia de seleção

Choose the MCP3422A7-E/MC for a compact, low-rate measurement system that needs 18-bit resolution, two differential inputs, an integrated 2.048 V reference, and a 3.75 samples/s conversion option. It is particularly suitable for slow pressure, temperature, battery, process, and environmental sensors where common-mode noise must be rejected and board area is limited. The MCP3422A4T-E/MC is the explicitly documented family-level replacement candidate, with consistent terminals and packages, and should be preferred when its conversion timing better matches the measurement system. The A0, A1, A2, and A6 family alternatives retain the core resolution, differential input, reference, supply, and interface architecture but use different conversion-rate options. Before substituting any family member, verify the required sampling latency, noise performance, PGA behavior, software configuration, exposed-pad layout, and exact package suffix.

Comparação com alternativas

Parâmetro Este produto MCP3422A4T-E/MC MCP3422A0T-E/MC MCP3422A1T-E/MC MCP3422A2T-E/MC MCP3422A6T-E/MC
Brand Microchip Technology Microchip Technology Microchip Technology Microchip Technology Microchip Technology Microchip Technology
Package 8-DFN (2x3) 8-DFN (2x3) 8-DFN (2x3) 8-DFN (2x3) 8-DFN (2x3) 8-DFN (2x3)
Resolution 18 bits 18 bits 18 bits 18 bits 18 bits 18 bits
Input Channels 2 differential inputs 2 differential inputs 2 differential inputs 2 differential inputs 2 differential inputs 2 differential inputs
Supply Voltage Range 2.7 V to 5.5 V 2.7 V to 5.5 V 2.7 V to 5.5 V 2.7 V to 5.5 V 2.7 V to 5.5 V 2.7 V to 5.5 V
Internal Reference 2.048 V precision reference 2.048 V precision reference 2.048 V precision reference 2.048 V precision reference 2.048 V precision reference 2.048 V precision reference
Serial Interface Two-wire I2C-compatible Two-wire I2C-compatible Two-wire I2C-compatible Two-wire I2C-compatible Two-wire I2C-compatible Two-wire I2C-compatible
Programmable Gain Amplifier Integrated PGA Integrated PGA Integrated PGA Integrated PGA Integrated PGA Integrated PGA
Differential Input Range +/-2.048 V with internal reference +/-2.048 V with internal reference +/-2.048 V with internal reference +/-2.048 V with internal reference +/-2.048 V with internal reference +/-2.048 V with internal reference

Principais diferenciais

  • Conversion option selected for 3.75 samples/s operation (vs MCP3422A4T-E/MC)
  • Compact differential measurement front end (vs MCP3422A0T-E/MC)
  • No separate precision reference required (vs MCP3422A1T-E/MC)
  • Single-supply operation with integrated PGA (vs MCP3422A2T-E/MC)

Notas de projeto

Route the two differential inputs as a matched pair, keep both traces short, and avoid switching nodes beneath the analog inputs. Terminate the source network so the impedances seen by both inputs remain similar. This preserves common-mode rejection and reduces conversion error caused by unequal settling. Use a quiet analog return and keep digital interface current away from the reference and input ground paths.

Place the supply bypass capacitor immediately beside the converter's supply and ground pins, with a short and low-inductance connection. Keep the analog and digital grounds joined at a controlled location near the device or power-entry point. The MCP3422A7-E/MC accepts 2.7 V to 5.5 V, but the selected rail must remain within that range during startup, transient, and fault conditions.

Do not treat the 18-bit nominal resolution as 18 bits of guaranteed absolute accuracy; reference error, offset, noise, input impedance, and conversion timing affect the usable result. Account for the 3.75 samples/s acquisition rate when setting sensor settling time or control-loop latency. For the 2 x 3 mm DFN package, implement the exposed-pad connection and land pattern exactly as shown in the manufacturer package drawing.

Add analog filtering close to the ADC pins when the sensor cable can pick up high-frequency interference. Choose filter capacitors and resistors that preserve the required settling time at the selected PGA gain and conversion rate. Differential filtering components should be closely matched. If a front-end op-amp drives the converter, verify its settling behavior for the selected gain rather than relying only on its small-signal bandwidth.

Informações de conformidade

RoHS
Compliant
REACH
Unknown
AEC-Q100
Unknown
Sem chumbo
Unknown
Sem halogênios
Unknown
Minerais de conflito
Unknown

The product listing identifies the MCP3422A7-E/MC as RoHS. The automotive designation appears in the family listing, but no separate AEC-Q100 qualification statement, lead-free statement, halogen-free statement, or conflict-minerals statement is provided.

Dados verificados em: 2026-11-20 — dados verificados e curados pela equipe de engenharia de componentes da XAIPART

Buscas relacionadas

MCP3422A7-E/MC datasheet MCP3422A7-E/MC specifications MCP3422A7-E/MC pinout MCP3422A7-E/MC datasheet pdf Microchip MCP3422A7-E/MC MCP3422A7-E/MC equivalent MCP3422A7-E/MC replacement MCP3422A7-E/MC cross reference MCP3422A7-E/MC vs MCP3422A4T-E/MC MCP3422A7-E/MC price MCP3422A7-E/MC stock MCP3422A7-E/MC application circuit 18-bit dual-input delta-sigma ADC 8-DFN 2x3 precision ADC

Componentes & termos relacionados

Microchip Technology MCP3422A7-E/MC MCP3422A4T-E/MC MCP3422A0T-E/MC MCP3422A1T-E/MC MCP3422A2T-E/MC MCP3422A6T-E/MC MCP3422 MCP3301T-BI/SN MCP607T-I/SN ADC analog-to-digital converter delta-sigma ADC differential input programmable gain amplifier PGA internal precision reference 2.048 V reference I2C-compatible interface 8-DFN package DFN-8 surface-mount package precision measurement pressure sensor interface
RFQ de cotação rápida
Preencha todos os detalhes — nossa equipe de vendas responderá em até 24 horas
Part number Fabricante Encapsulamento QTY Preço-alvo Total
✓
Cotação enviada!

Responderemos seu e-mail em até 24 horas

1
RFQ enviada
2
Cotação recebida
3
Pedido realizado
4
Pagamento
5
Enviado
6
Entregue
Ver detalhes da RFQ