MCP604T-I/SL - 2.8MHz Quad RRO Op Amp | Microchip Technology
MPN: MCP604T-I/SL ✓ সক্রিয়MCP604T-I/SL সারাংশ
An operational amplifier, or op amp, is a high-gain analog building block used to amplify weak sensor signals, buffer inputs, compare voltages, and drive control signals. The MCP604 belongs to the hierarchy of op amps, analog amplifiers, interface ICs, and semiconductors. Its four integrated amplifiers reduce component count in multi-channel instrumentation while preserving consistent electrical performance across each channel.
Principal features include a 2.8 MHz gain-bandwidth product, typical supply current of 230 µA per amplifier, input bias current of 1 pA, slew rate of 2.3 V/µs, and maximum input offset voltage of 2 mV. The rail-to-rail output stage supports low-voltage signal chains where the useful output range must approach the supply rails.
The MCP604 family uses Microchip's advanced CMOS technology to combine low bias current, high open-loop gain, and low operating current in a compact quad configuration. Each amplifier is unity-gain stable, simplifying buffer and general-purpose voltage-feedback layouts. Operation from 2.7 V supports battery-powered and modern low-voltage embedded systems without requiring a negative supply.
Typical uses include portable instrumentation, battery-operated sensor interfaces, industrial control modules, low-voltage data acquisition, audio signal conditioning, and general-purpose analog signal chains. Four channels in one package are particularly useful when several independent sensor outputs must be amplified with comparable circuitry.
When designing around the MCP604T-I/SL, maintain adequate output headroom for the connected load and account for input and output capacitance when estimating stability and bandwidth. Bypass the supply pins with a local ceramic capacitor and route sensitive input traces away from switching nodes and high-current return paths.
This product overview consolidates the device's core electrical characteristics, package information, sourcing guidance, comparison options, and application guidance. It also highlights practical differences among pin-compatible options so engineers can select a replacement according to grade, bandwidth, offset, and application requirements rather than package designation alone.
এর জন্য ড্রপ-ইন বিকল্প MCP604T-I/SL — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।
এই সিরিজের ভ্যারিয়েন্ট
একই সিরিজের মডেল যেগুলো drop-in compatible MCP604T-I/SL (একই form factor এবং footprint) — পার্থক্য রয়েছে Package, Mounting Type, Amplifier Type, Typical Operating Current, Input Bias Current.
MCP604T-E/SL
✅ ড্রপ-ইনমূল্যের জন্য যোগাযোগ করুন
ডেটাশিট দেখুন →MCP604-I/SL
✅ ড্রপ-ইনমূল্যের জন্য যোগাযোগ করুন
ডেটাশিট দেখুন →MCP6024T-I/SL
✅ ড্রপ-ইন📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
MCP6004T-I/SL
✅ ড্রপ-ইন📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
MCP6002T-I/SNVAO
✅ ড্রপ-ইন📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
MCP604T-I/SL সর্বোচ্চ রেটিং ও বৈদ্যুতিক বৈশিষ্ট্য
| Amplifier Count | 4 channels |
| Product Type | CMOS operational amplifier |
| Gain-Bandwidth Product | 2.8 MHz |
| Minimum Supply Voltage | 2.7 V |
| Maximum Supply Voltage | 6.0 V |
| Typical Supply Current | 230 µA per amplifier |
| Input Bias Current | 1 pA |
| Slew Rate | 2.3 V/µs |
| Maximum Input Offset Voltage | 2 mV |
| Output Swing | Rail-to-rail |
| Unity-Gain Stability | Yes |
| অপারেটিং তাপমাত্রার পরিসর | -40°C to +85°C |
| প্যাকেজ | 14-pin SOIC, 3.90 mm width |
| মাউন্টিং টাইপ | Surface mount |
| Automotive Qualification | AEC-Q100 |
| Supply Configuration | Single supply |
MCP604T-I/SL পিন কনফিগারেশন
| পিন 1 | OUTA — Amplifier A output |
| পিন 2 | -INA — Inverting input for amplifier A |
| পিন 3 | +INA — Noninverting input for amplifier A |
| পিন 4 | V- — Negative supply connection |
| পিন 5 | +INB — Noninverting input for amplifier B |
| পিন 6 | -INB — Inverting input for amplifier B |
| পিন 7 | OUTB — Amplifier B output |
| পিন 8 | OUTC — Amplifier C output |
| পিন 9 | -INC — Inverting input for amplifier C |
| পিন 10 | +INC — Noninverting input for amplifier C |
| পিন 11 | V+ — Positive supply connection |
| পিন 12 | +IND — Noninverting input for amplifier D |
| পিন 13 | -IND — Inverting input for amplifier D |
| পিন 14 | OUTD — Amplifier D output |
সাধারণ ব্যবহার
MCP604T-I/SL এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Battery-Powered Sensor Conditioning, Industrial Control and Instrumentation, Low-Voltage Data Acquisition, Portable Medical and Monitoring Equipment, Audio and Low-Frequency Signal Conditioning, Automotive Auxiliary Signal Interfaces.
Battery-Powered Sensor Conditioning
The MCP604T-I/SL fits low-voltage sensor front ends because each of its four channels operates from a single supply as low as 2.7 V, draws a typical 230 µA per amplifier, and has an input bias current of 1 pA. The low bias current helps preserve signals from high-impedance sensors, while the four-channel package can condition multiple outputs without adding four separate packages. Each amplifier is unity-gain stable, allowing direct buffering when the source impedance requires it. The 2.3 V/µs slew rate and 2.8 MHz gain-bandwidth product also provide more bandwidth than many low-power sensors require, but the design should still verify the common-mode range, output swing, sensor settling time, and supply-current budget.
সুপারিশকৃত
Industrial Control and Instrumentation
MCP604T-I/SL is appropriate for industrial instrumentation requiring multiple low-power analog channels within a -40°C to +85°C operating range. Its four rail-to-rail-output amplifiers can buffer sensor inputs, amplify control signals, or drive moderate loads from one 14-pin SOIC package. The 2.8 MHz gain-bandwidth product gives sufficient loop bandwidth for many slow process-control and measurement paths, while the 2 mV maximum input offset supports signal integrity in practical instrumentation. Designers should verify the output-current demand, capacitive loading, analog ground arrangement, and input filtering at each channel. The industrial temperature range makes the device more broadly suitable than a consumer-grade amplifier when equipment may operate outside room temperature.
সুপারিশকৃত
Low-Voltage Data Acquisition
The MCP604T-I/SL can implement a compact four-channel analog acquisition front end when each channel needs buffering or moderate amplification. Its 1 pA input bias current minimizes loading on high-impedance sources, and the 2.8 MHz gain-bandwidth product allows closed-loop gains to be selected according to the required signal bandwidth. Rail-to-rail output operation improves usable range in 2.7 V systems where conventional non-rail-to-rail amplifiers could lose swing. In a practical circuit, place the amplifier close to the sensor or connector, use short protected input routes, and add an anti-alias filter before any switching converter or higher-bandwidth stage. The 2 mV maximum offset and 2.3 V/µs slew rate must be included in the error and settling analysis.
সুপারিশকৃত
Portable Medical and Monitoring Equipment
The MCP604T-I/SL can support low-level signal conditioning in portable monitoring equipment when the device's noise, offset, and input characteristics satisfy the measurement specification. Its four channels reduce board area for multielectrode, pressure, or biosensor interfaces, while single-supply operation from 2.7 V supports compact battery-powered designs. The 1 pA input bias current is useful with high-impedance sources, and the unity-gain-stable configuration simplifies isolation and follower stages. Designers must account for leakage current through board contaminants, patient protection requirements, input protection networks, and the difference between input offset and the complete error budget. These system protections are separate from the amplifier specifications and should be validated according to the applicable product requirements.
সুপারিশকৃত
Audio and Low-Frequency Signal Conditioning
MCP604T-I/SL can serve as a general-purpose amplifier in low-frequency audio, control, and communication paths where rail-to-rail output and low bias current are more important than wideband performance. The 2.8 MHz gain-bandwidth product supports channels through the audio band and beyond, while the 2.3 V/µs slew rate helps produce clean output transitions into moderate loads. Its four independent channels can support mixer, headphone-buffer, or interface stages, although the MCP604 is not a specialized audio amplifier and does not by itself guarantee low distortion at every gain and load. PCB design should keep input and output paths short, maintain symmetric feedback routing, and connect the bypass capacitor close to the supply pins to suppress supply ripple.
সুপারিশকৃত
Automotive Auxiliary Signal Interfaces
MCP604T-I/SL is identified for automotive AEC-Q100 applications in a 14-pin SOIC package, making it relevant for low-speed auxiliary signal interfaces rather than high-bandwidth safety-critical processing. Its four rail-to-rail-output channels can buffer switches, sensors, or diagnostic signals, and operation from 2.7 V supports modern low-voltage vehicle electronics. The -40°C to +85°C industrial range covers many cabin and external electronics environments. Automotive qualification does not mean the part is suitable for every safety-critical function; engineers must apply the vehicle OEM's own qualification, transient, immunity, and functional-safety requirements. Protection networks, ground-bounce margins, and diagnostic coverage also require system-level validation.
সুপারিশকৃত
সুপারিশকৃত পণ্যের সারসংক্ষেপ
এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা MCP604T-I/SL — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।
নির্বাচন গাইড
বিকল্পের সাথে তুলনা
| পারামিটার | এই পণ্য | MCP604T-E/SL | MCP604-I/SL | MCP6024T-I/SL | MCP6004T-I/SL | MCP6002T-I/SNVAO |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 14-pin SOIC | 14-pin SOIC - same | 14-pin SOIC - same | 14-pin SOIC - same | 14-pin SOIC - same | 14-pin SOIC - same |
| Amplifier Count | 4 channels | 4 channels | 4 channels | 4 channels | 4 channels | 4 channels |
মূল পার্থক্যসমূহ
- Higher gain-bandwidth product within the directly compared quad families (বনামMCP6024T-I/SL)
- Very low input bias current for high-impedance signal sources (বনামMCP6004T-I/SL)
- Low quiescent current with four integrated channels (বনামMCP604-I/SL)
ডিজাইন নোট
Place the supply bypass capacitor immediately between the V+ and V- pins, with a short, low-inductance connection to the ground plane. Route the four channels to minimize loop area and keep feedback resistors close to their associated amplifier pins. Sensitive inputs should remain away from switching-regulator nodes, relay contacts, and high-current output traces to reduce coupled noise.
Do not assume that a 14-pin SOIC footprint alone guarantees an equivalent amplifier. MCP604T-E/SL, MCP604-I/SL, MCP6024T-I/SL, MCP6004T-I/SL, and MCP6002T-I/SNVAO differ in temperature grade, bandwidth class, packing, or detailed electrical limits. Before substitution, confirm the input common-mode range, output swing, gain-bandwidth product, offset, bias current, supply current, slew rate, and AEC-Q100 requirements.
The MCP604 is unity-gain stable, but practical stability still depends on output loading and feedback topology. Avoid placing large capacitive loads directly on an output unless the operating frequency and amplifier configuration have been checked. For source impedances above the recommended range, minimize trace length, maintain a stable reference return, and consider buffering the source before adding further gain.
Budget supply current for four amplifiers rather than one because each channel typically draws 230 µA. In battery systems, include quiescent current, regulator efficiency, and any output-current demand in the operating profile. The 2.7 V minimum supply also constrains input and output headroom, so downstream and upstream levels should be checked against the device's common-mode and rail-to-rail operating characteristics.
কমপ্লায়েন্স তথ্য
The Arrow listing identifies MCP604T-I/SL as an automotive AEC-Q100 device. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status are unknown.