MK2308S-1HILF - 133MHz 8-Output Zero-Delay Buffer | Renesas
MPN: MK2308S-1HILF ✓ সক্রিয়MK2308S-1HILF সারাংশ
A zero-delay buffer is a clock-buffer IC that compensates propagation delay through its internal PLL so multiple destinations receive aligned clock edges. The MK2308S-1HILF belongs to the clock buffer and driver hierarchy, where clock management ICs support frequency synthesis, distribution, buffering, and low-skew fanout across digital, communications, industrial, and embedded systems.
The principal operating characteristics are a 3.3 V supply, a maximum clock frequency of 133 MHz, eight outputs, and a 1:8 input-to-output fanout ratio. Outputs may be generated through the PLL for zero-delay operation or routed directly from the input for testing. CMOS outputs and low-skew behavior make the device appropriate for systems requiring predictable clock propagation among multiple loads.
The PLL-based architecture is the core technical feature of the MK2308S-1HILF. It provides eight low-skew outputs at speeds up to 133 MHz, while bypass mode allows a clock to pass directly from the input to the outputs. The external-component requirements remain modest: the manufacturer datasheet specifies 0.01 mF decoupling capacitors at the two VDD and GND supply-pin pairs and notes that a 33 ohm series termination resistor may be used on each clock output to reduce reflections.
Typical uses include fanout to processors, FPGAs, memory controllers, communications transceivers, and other clock-domain-crossing or multi-load systems. Eight outputs reduce the number of separate clock fanout stages required, while the low-skew characteristic helps preserve timing relationships between parallel interfaces and sequential logic.
PCB implementation requires careful treatment of clock traces. Place the supply bypass capacitors adjacent to the specified pins, use short clock routes, maintain a continuous return path, and consider source termination when trace length, impedance discontinuities, or capacitive loading could produce reflections. Validate output timing and power integrity on the final board because package, connector, and interposer parasitics are not represented by the nominal frequency specification alone.
This page combines the device architecture, operating limits, application guidance, pin-package information, and engineering trade-offs in one reference. It also distinguishes the directly supported ordering options from merely similar clock-buffer products, helping designers assess fit without treating unrelated package or feature sets as drop-in replacements.
এর জন্য ড্রপ-ইন বিকল্প MK2308S-1HILF — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।
MK2308S-1HILFTR
✅ ড্রপ-ইন📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
MK2308S-1HILF বিশেষণ
| Product Type | PLL-based zero-delay buffer |
| সর্বোচ্চ ক্লক ফ্রিকোয়েন্সি | 133 MHz |
| সাপ্লাই ভোল্টেজ | 3.3 V |
| আউটপুটের সংখ্যা | 8 outputs |
| Input-to-Output Ratio | 1:8 |
| আউটপুট টাইপ | CMOS |
| PLL Bypass | Supported |
| Zero-Delay Output | Supported through PLL |
| Tri-State Output | Supported |
| Phase Noise | Low phase noise |
| Output Skew | Low skew |
| Circuit Count | 1 circuit |
| Input Type | Clock input |
| প্যাকেজ | 16-SOIC, 0.154 inch body width, 3.90 mm width |
| মাউন্টিং টাইপ | Surface mount |
| Decoupling Requirement | 0.01 mF between VDD and GND on pins 4-5 and 13-12 |
| Optional Output Series Termination | 33 ohm per clock output |
MK2308S-1HILF 16-soic, 0.154 inch body width, 3.90 mm width পিন কনফিগারেশন গাইড
MK2308S-1HILF (16-soic, 0.154 inch body width, 3.90 mm width প্যাকেজ)-এর পিন কনফিগারেশন। পিন নম্বরিং, ফাংশন এবং সংযোগ ডায়াগ্রাম প্রস্তুতকারকের ডেটাশিটে সংজ্ঞায়িত করা আছে। সঠিক ফুটপ্রিন্ট এবং সোল্ডারিং নির্দেশিকার জন্য এটি দেখুন।
এর জন্য বিস্তারিত পিনআউট ডেটা পাওয়া যায়নি MK2308S-1HILF.
দেখুন ডেটাশিট সম্পূর্ণ পিন কনফিগারেশনের জন্য।
সাধারণ ব্যবহার
MK2308S-1HILF এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Processor and FPGA Clock Fanout, Communications Interface Clocking, Memory Controller Clock Distribution, Industrial Control and Instrumentation, Network and Communication Equipment, Embedded Digital Subsystems.
Processor and FPGA Clock Fanout
The MK2308S-1HILF fits a multi-destination system clock tree because it distributes one input clock to eight low-skew CMOS outputs at frequencies up to 133 MHz. The PLL-based zero-delay path helps align the edges delivered to processors, FPGAs, and their associated peripherals. Place the device close to the clock source, route outputs to controlled-impedance destinations, and verify setup and hold timing at each receiver. The eight outputs can reduce the number of cascaded fanout buffers required, while PLL bypass provides a useful diagnostic path when isolating clock-distribution behavior.
সুপারিশকৃত
Communications Interface Clocking
For parallel communications interfaces, the MK2308S-1HILF can provide eight low-skew clock outputs from one 3.3 V source clock. Its maximum specified operating frequency of 133 MHz makes it relevant to moderately paced digital links whose transmitters and receivers require coordinated clock arrival. Use matched output routing and account for output-to-output skew and board skew during timing analysis. PLL bypass can assist board bring-up by checking signal integrity independently of the zero-delay operating path, while the final design should confirm that the source clock and interface limits remain within device specifications.
সুপারিশকৃত
Memory Controller Clock Distribution
The MK2308S-1HILF is applicable when a memory controller must deliver a coordinated clock to several loads. Its eight 3.3 V CMOS outputs support low-skew distribution at up to 133 MHz, and the PLL path provides the device's zero-delay operating mode. Keep clock traces short and route them over an uninterrupted reference plane to limit skew and coupling. Check receiver capacitance, edge rate, and termination against the clock receiver's requirements. PLL bypass should remain available for signal-integrity testing without changing the board's primary clock-distribution topology.
সুপারিশকৃত
Industrial Control and Instrumentation
Industrial control electronics often distribute a common clock to multiple acquisition, processing, and communications blocks. The MK2308S-1HILF provides eight low-skew outputs at 3.3 V and up to 133 MHz, allowing a compact 16-SOIC implementation where several destinations require a consistent edge relationship. Its tri-state capability can support controlled output states in multi-source arrangements. The design must still account for cable or connector loading, long clock routes, and ground bounce. Use the manufacturer's 0.01 mF supply bypass placement guidance and consider the suggested 33 ohm output series termination when reflections appear.
সুপারিশকৃত
Network and Communication Equipment
Network equipment can benefit from the MK2308S-1HILF when one system clock must reach multiple low-speed or medium-speed logic domains. Its 1:8 fanout and eight low-skew CMOS outputs provide a practical way to organize clock routing, while the 133 MHz rating covers the device's documented operating range. In multilayer equipment, preserve a continuous return path beneath every clock trace and separate outputs enough to limit crosstalk. Confirm input slew, output loading, and downstream timing before release to production. PLL bypass offers a straightforward test mode for separating source-clock problems from distribution or receiver issues.
সুপারিশকৃত
Embedded Digital Subsystems
Embedded subsystems commonly use one oscillator output to feed several internal and external clocked blocks. The MK2308S-1HILF offers a 16-SOIC, eight-output implementation at 3.3 V, with PLL-based zero-delay operation up to 133 MHz. Place the bypass capacitors adjacent to the documented supply pins and keep clock routing away from noisy switching nodes to reduce jitter coupling. Tri-state outputs can assist bus-oriented clock arrangements, but output-enable behavior must be coordinated with the system controller. The PLL bypass path is also useful during production testing when engineers need to evaluate clock integrity independently of the nominal zero-delay mode.
সুপারিশকৃত
এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা MK2308S-1HILF — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।
নির্বাচন গাইড
বিকল্পের সাথে তুলনা
| পারামিটার | এই পণ্য | MK2308S-1HILFTR |
|---|---|---|
| Brand | Renesas Electronics | Renesas Electronics |
| Package | 16-SOIC, 0.154 inch body width, 3.90 mm width | 16-SOIC |
| Product Type | PLL-based zero-delay buffer | PLL-based zero-delay buffer |
| Maximum Clock Frequency | 133 MHz | 133 MHz |
| Supply Voltage | 3.3 V | 3.3 V |
| Number of Outputs | 8 outputs | 8 outputs |
| Input-to-Output Ratio | 1:8 | 1:8 |
| Output Type | CMOS | CMOS |
| PLL Bypass | Supported | Supported |
| Tri-State Output | Supported | Supported |
| Output Skew | Low skew | Low skew |
| Decoupling Requirement | 0.01 mF at VDD and GND pins 4-5 and 13-12 | 0.01 mF at VDD and GND pins 4-5 and 13-12 |
মূল পার্থক্যসমূহ
- Eight-way zero-delay clock fanout (বনামMK2308S-1HILFTR)
- Integrated PLL bypass for diagnostic testing (বনামMK2308S-1HILFTR)
- Low-skew CMOS output architecture (বনামMK2308S-1HILFTR)
ডিজাইন নোট
Place the two specified 0.01 mF decoupling capacitors directly beside the MK2308S-1HILF VDD and GND pairs on pins 4-5 and 13-12. Keep each capacitor's power and ground connections short, with the ground return referenced to the same low-impedance plane used by the clock outputs. Minimize loop area and avoid routing clock traces between the capacitor and its supply pins. This placement limits supply transients that could otherwise affect PLL operation and output edge timing.
Use the manufacturer's suggested 33 ohm series termination resistor on each clock output when trace loading or impedance discontinuities can produce reflections. Place the resistor close to the output driver so it damps the outgoing edge rather than creating a second discontinuity at the receiver. Validate the selection with an eye diagram or time-domain measurement at the actual receiver. If reflections are absent, remove the resistor through schematic and layout review rather than retaining unverified termination.
Route all eight clock outputs as controlled-impedance traces over a continuous reference plane and avoid crossings with high-speed data or switching-power paths. Keep output lengths and via transitions consistent where low-skew operation is critical. Avoid stubs and test-point structures that create significant capacitive loading. Evaluate source, series, load, and receiver capacitance in the timing budget because the nominal 133 MHz limit alone does not guarantee acceptable edge quality in every physical implementation.
Do not confuse PLL bypass with zero-delay operation: bypass provides a direct input-to-output test path, while the PLL path supplies the documented low-skew zero-delay behavior. Also avoid treating the eight outputs as independent arbitrary-frequency clocks, because the function is an eight-way clock fanout with a 1:8 ratio. Verify enable and tri-state behavior, input slew requirements, and pin assignments in the manufacturer datasheet before using multiple output-enable states in a shared-clock architecture.
কমপ্লায়েন্স তথ্য
No explicit RoHS, REACH, lead-free, halogen-free, conflict-minerals, or automotive qualification statement was identified for this exact ordering code.