Renesas Electronics

MK2308S-1HILF - 133MHz 8-Output Zero-Delay Buffer | Renesas

MPN: MK2308S-1HILF ✓ פעיל
3.3 V Vdss 16-SOIC, 0.154 inch body width, 3.90 mm width Package 133 MHz Speed
כמות הזמנה מינימלית: 1 |

MK2308S-1HILF סקירה

Renesas Electronics MK2308S-1HILF is a 3.3 V, 133 MHz zero-delay buffer IC with eight low-skew CMOS clock outputs in a 16-SOIC package. It uses a low-phase-noise PLL-based architecture to distribute one clock input across eight outputs while maintaining zero-delay operation. The device also supports PLL bypass and tri-state output operation.

A zero-delay buffer is a clock-buffer IC that compensates propagation delay through its internal PLL so multiple destinations receive aligned clock edges. The MK2308S-1HILF belongs to the clock buffer and driver hierarchy, where clock management ICs support frequency synthesis, distribution, buffering, and low-skew fanout across digital, communications, industrial, and embedded systems.

The principal operating characteristics are a 3.3 V supply, a maximum clock frequency of 133 MHz, eight outputs, and a 1:8 input-to-output fanout ratio. Outputs may be generated through the PLL for zero-delay operation or routed directly from the input for testing. CMOS outputs and low-skew behavior make the device appropriate for systems requiring predictable clock propagation among multiple loads.

The PLL-based architecture is the core technical feature of the MK2308S-1HILF. It provides eight low-skew outputs at speeds up to 133 MHz, while bypass mode allows a clock to pass directly from the input to the outputs. The external-component requirements remain modest: the manufacturer datasheet specifies 0.01 mF decoupling capacitors at the two VDD and GND supply-pin pairs and notes that a 33 ohm series termination resistor may be used on each clock output to reduce reflections.

Typical uses include fanout to processors, FPGAs, memory controllers, communications transceivers, and other clock-domain-crossing or multi-load systems. Eight outputs reduce the number of separate clock fanout stages required, while the low-skew characteristic helps preserve timing relationships between parallel interfaces and sequential logic.

PCB implementation requires careful treatment of clock traces. Place the supply bypass capacitors adjacent to the specified pins, use short clock routes, maintain a continuous return path, and consider source termination when trace length, impedance discontinuities, or capacitive loading could produce reflections. Validate output timing and power integrity on the final board because package, connector, and interposer parasitics are not represented by the nominal frequency specification alone.

This page combines the device architecture, operating limits, application guidance, pin-package information, and engineering trade-offs in one reference. It also distinguishes the directly supported ordering options from merely similar clock-buffer products, helping designers assess fit without treating unrelated package or feature sets as drop-in replacements.

חלופות תחליף ישיר עבור MK2308S-1HILF — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.

MK2308S-1HILFTR

✅ Drop-In
📦 16-SOIC
Alternate ordering suffix for the documented 133 MHz, eight-output 16-SOIC zero-delay-buffer function; no numerical electrical difference is stated

📋 חלופה להתייחסות (לא בקטלוג)

MK2308S-1HILF מפרטים

Product Type PLL-based zero-delay buffer
תדר שעון מקסימלי 133 MHz
מתח אספקה 3.3 V
מספר יציאות 8 outputs
Input-to-Output Ratio 1:8
סוג פלט CMOS
PLL Bypass Supported
Zero-Delay Output Supported through PLL
Tri-State Output Supported
Phase Noise Low phase noise
Output Skew Low skew
Circuit Count 1 circuit
Input Type Clock input
מארז 16-SOIC, 0.154 inch body width, 3.90 mm width
סוג הרכבה Surface mount
Decoupling Requirement 0.01 mF between VDD and GND on pins 4-5 and 13-12
Optional Output Series Termination 33 ohm per clock output

מדריך תצורת פינים של MK2308S-1HILF 16-soic, 0.154 inch body width, 3.90 mm width

תצורת פינים עבור MK2308S-1HILF (מארזת 16-soic, 0.154 inch body width, 3.90 mm width). מספרי פינים, פונקציות ותרשימי חיבורים מוגדרים ב-Datasheet של היצרן. יש לעיין בו לקבלת ה-footprint המדויק והנחיות הלחמה.

תרשים פינים של מארזת 16-soic, 0.154 inch body width, 3.90 mm width עבור MK2308S-1HILF

אין נתוני פריסת פינים מפורטים עבור MK2308S-1HILF.

עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.

יישומים טיפוסיים

MK2308S-1HILF מתאים עבור 6 יישוםs: Processor and FPGA Clock Fanout, Communications Interface Clocking, Memory Controller Clock Distribution, Industrial Control and Instrumentation, Network and Communication Equipment, Embedded Digital Subsystems.

🖥️

Processor and FPGA Clock Fanout

The MK2308S-1HILF fits a multi-destination system clock tree because it distributes one input clock to eight low-skew CMOS outputs at frequencies up to 133 MHz. The PLL-based zero-delay path helps align the edges delivered to processors, FPGAs, and their associated peripherals. Place the device close to the clock source, route outputs to controlled-impedance destinations, and verify setup and hold timing at each receiver. The eight outputs can reduce the number of cascaded fanout buffers required, while PLL bypass provides a useful diagnostic path when isolating clock-distribution behavior.

🌐

Communications Interface Clocking

For parallel communications interfaces, the MK2308S-1HILF can provide eight low-skew clock outputs from one 3.3 V source clock. Its maximum specified operating frequency of 133 MHz makes it relevant to moderately paced digital links whose transmitters and receivers require coordinated clock arrival. Use matched output routing and account for output-to-output skew and board skew during timing analysis. PLL bypass can assist board bring-up by checking signal integrity independently of the zero-delay operating path, while the final design should confirm that the source clock and interface limits remain within device specifications.

🖥️

Memory Controller Clock Distribution

The MK2308S-1HILF is applicable when a memory controller must deliver a coordinated clock to several loads. Its eight 3.3 V CMOS outputs support low-skew distribution at up to 133 MHz, and the PLL path provides the device's zero-delay operating mode. Keep clock traces short and route them over an uninterrupted reference plane to limit skew and coupling. Check receiver capacitance, edge rate, and termination against the clock receiver's requirements. PLL bypass should remain available for signal-integrity testing without changing the board's primary clock-distribution topology.

🏭

Industrial Control and Instrumentation

Industrial control electronics often distribute a common clock to multiple acquisition, processing, and communications blocks. The MK2308S-1HILF provides eight low-skew outputs at 3.3 V and up to 133 MHz, allowing a compact 16-SOIC implementation where several destinations require a consistent edge relationship. Its tri-state capability can support controlled output states in multi-source arrangements. The design must still account for cable or connector loading, long clock routes, and ground bounce. Use the manufacturer's 0.01 mF supply bypass placement guidance and consider the suggested 33 ohm output series termination when reflections appear.

🌐

Network and Communication Equipment

Network equipment can benefit from the MK2308S-1HILF when one system clock must reach multiple low-speed or medium-speed logic domains. Its 1:8 fanout and eight low-skew CMOS outputs provide a practical way to organize clock routing, while the 133 MHz rating covers the device's documented operating range. In multilayer equipment, preserve a continuous return path beneath every clock trace and separate outputs enough to limit crosstalk. Confirm input slew, output loading, and downstream timing before release to production. PLL bypass offers a straightforward test mode for separating source-clock problems from distribution or receiver issues.

🔧

Embedded Digital Subsystems

Embedded subsystems commonly use one oscillator output to feed several internal and external clocked blocks. The MK2308S-1HILF offers a 16-SOIC, eight-output implementation at 3.3 V, with PLL-based zero-delay operation up to 133 MHz. Place the bypass capacitors adjacent to the documented supply pins and keep clock routing away from noisy switching nodes to reduce jitter coupling. Tri-state outputs can assist bus-oriented clock arrangements, but output-enable behavior must be coordinated with the system controller. The PLL bypass path is also useful during production testing when engineers need to evaluate clock integrity independently of the nominal zero-delay mode.

What is the operating voltage of MK2308S-1HILF?
The MK2308S-1HILF operates from a 3.3 V supply. According to the Renesas manufacturer datasheet, the device is a 3.3 V PLL-based zero-delay buffer, and its output frequency capability extends to 133 MHz. The supply pins should be decoupled with 0.01 mF capacitors connected across the specified VDD and GND pin pairs. Maintain short supply connections and a low-impedance return path so switching activity on the eight clock outputs does not degrade the PLL reference or create excessive supply noise.
What are the key specifications of MK2308S-1HILF that engineers should know?
The MK2308S-1HILF is a 3.3 V, 133 MHz, eight-output CMOS zero-delay buffer in a 16-SOIC package. According to the Renesas manufacturer datasheet, it distributes one clock input through eight low-skew outputs, provides a 1:8 input-to-output ratio, supports PLL bypass for direct testing, and permits tri-state outputs. The PLL path produces the specified zero-delay behavior, while the low-skew output characteristic helps maintain timing relationships among multiple clocked loads.
What is the maximum frequency of MK2308S-1HILF?
The maximum specified clock frequency of the MK2308S-1HILF is 133 MHz at 3.3 V. According to the Renesas manufacturer datasheet, the device can generate eight low-skew outputs from its internal PLL at speeds up to 133 MHz. This rating applies to the device's specified operating conditions and should not be interpreted as guaranteeing acceptable timing at every board topology. Validate rise time, loading, trace length, jitter margin, and downstream receiver requirements in the completed design.
How many clock outputs does MK2308S-1HILF provide?
The MK2308S-1HILF provides eight clock outputs with a 1:8 input-to-output fanout ratio. According to the Renesas manufacturer datasheet, the outputs can be generated through the PLL for zero-delay operation or directly from the input through PLL bypass for testing. All eight outputs are CMOS and can enter tri-state operation. The eight-way fanout is useful when a single source clock must feed multiple processors, FPGAs, memory interfaces, or communications blocks.
Where can I download the MK2308S-1HILF datasheet PDF?
The MK2308S-1HILF datasheet PDF is available at the official technical document URL shown on this page. The document identifies the device as a low-phase-noise, high-speed PLL-based eight-output low-skew zero-delay buffer and includes its external-component requirements. Use the manufacturer's pin-description and electrical-characteristics tables when assigning PCB signals, selecting decoupling, and checking the 133 MHz operating limit. The document also supports PLL bypass, tri-state operation, and output termination guidance.
Where can I find the MK2308S-1HILF pinout?
The MK2308S-1HILF uses a 16-SOIC package, and its numbered pin assignment is shown in the Renesas manufacturer datasheet. The documented power connections include VDD and GND pairs on pins 4-5 and 13-12, with 0.01 mF bypass capacitors placed as close to the device as possible. Use the datasheet pin table to identify the clock input, individual outputs, control inputs, and any test or reference functions before assigning the remaining PCB nets.
What decoupling capacitors does MK2308S-1HILF require?
The MK2308S-1HILF requires 0.01 mF decoupling capacitors between VDD and GND at pins 4-5 and pins 13-12. According to the Renesas manufacturer datasheet, these capacitors should be connected as close to the device as possible. Place each capacitor directly beside its associated supply and ground pins, use short traces, and provide a stable ground reference for all eight clock outputs. The datasheet also notes that a 33 ohm series resistor may be placed in each output path to reduce reflections.
What is the difference between zero-delay mode and PLL bypass?
Zero-delay mode uses the MK2308S-1HILF internal PLL to create eight low-skew outputs while compensating for propagation delay, whereas PLL bypass routes the input clock directly toward the outputs. According to the Renesas manufacturer datasheet, both operating paths are available, and direct bypass is useful for testing. Choose zero-delay mode when clock alignment is required and use bypass only when the system intentionally accepts the path's propagation delay or uses it for diagnostic evaluation.
Where to buy MK2308S-1HILF online?
Use the Request a Quote form on this page to request the MK2308S-1HILF with the required quantity and packaging information. Current commercial availability, production allocation, and lead time should be confirmed through that form before a purchase commitment is made. The part is identified as a Renesas Electronics 133 MHz, eight-output, 16-SOIC zero-delay buffer, so the quote request should include the exact MK2308S-1HILF ordering code to avoid confusion with related package or ordering variants.
What is the price of MK2308S-1HILF?
The current commercial price for the MK2308S-1HILF is handled through the Request a Quote form on this page. The request should state the required quantity, delivery location, and desired shipment terms so current channel pricing and availability can be confirmed. For engineering evaluation, the key product facts are the 3.3 V supply, 133 MHz maximum clock frequency, eight CMOS outputs, and 16-SOIC package. Those specifications determine suitability independently of the commercial quotation.
What is the lead time for MK2308S-1HILF?
The current lead time for the MK2308S-1HILF must be confirmed through the Request a Quote form on this page. Include the required order quantity, target delivery date, and any acceptable alternate shipment plan. Production scheduling can vary with order volume and component availability, so a lead-time statement should be obtained for the exact MPN rather than inferred from generic market conditions. The device's current manufacturer listing and distributor presence support sourcing review, but they do not constitute a quotation.
Is MK2308S-1HILF in stock?
Stock for the MK2308S-1HILF should be confirmed through the Request a Quote form on this page using the exact ordering code and required quantity. The form allows current inventory and allocation to be checked for the requested shipment plan without inserting static stock claims that may quickly become obsolete. Before requesting a quote, verify that your design requires the 16-SOIC package, 3.3 V operation, eight low-skew outputs, and the zero-delay or bypass functions specified for this device.
MK2308S-1HILF vs MK2308S-1HILFTR - which is better for a PCB assembly?
MK2308S-1HILF and MK2308S-1HILFTR identify ordering variants of the same 16-SOIC clock-buffer function, so the appropriate choice depends on the assembly format required by the board builder. The comparison is primarily about ordering or packaging handling rather than a change in the documented 133 MHz, eight-output electrical function. Confirm the exact reel or tube notation with the contract manufacturer and request the applicable quote using the complete MPN printed on the production bill of materials.
When should I choose MK2308S-1HILF over a conventional clock buffer?
Choose the MK2308S-1HILF when one clock must feed eight destinations and the design benefits from PLL-based zero-delay output with low skew. According to the Renesas manufacturer datasheet, it supports operation to 133 MHz, PLL bypass, tri-state outputs, and a 3.3 V supply. A conventional multi-output buffer may be preferable when zero-delay alignment is unnecessary and a lower-complexity solution is sufficient. The decision should consider timing margin, fanout count, output loading, and system clock architecture.
Is MK2308S-1HILF suitable for a low-skew multi-load clock tree?
The MK2308S-1HILF is suitable for a low-skew multi-load clock tree because it provides eight low-skew CMOS outputs from one input using a PLL-based architecture. According to the Renesas manufacturer datasheet, the device operates at 3.3 V up to 133 MHz and can also bypass the PLL for testing. Suitability still depends on output loading, trace topology, receiver requirements, and timing margins in the final board, so those conditions should be verified with the complete design.
What can replace MK2308S-1HILF?
The closest directly identified replacement is MK2308S-1HILFTR, which is the alternate ordering representation listed for the same Renesas device and retains the documented clock-buffer function. The MK2308S-1HILFTR listing appears in the manufacturer-linked channel results, but the complete ordering format must be checked before substitution. No cross-manufacturer part is presented as a confirmed drop-in replacement because the available cross-reference results do not establish a pin-compatible 16-SOIC device with verified electrical equivalence.
Is there a Renesas equivalent for MK2308S-1HILF?
MK2308S-1HILFTR is the directly identified Renesas ordering alternative for the MK2308S-1HILF in the available manufacturer-linked listings. It represents the same 16-SOIC zero-delay-buffer ordering family rather than a substantively different competitor. For a cross-brand replacement, engineers should not assume pin compatibility from the generic frequency, output count, and package alone. Confirm the pin table, control functions, power pins, output timing, and electrical limits before approving any substitution.

נתוני עזר הנדסיים עבור MK2308S-1HILF — השוואה, הנחיות תכנון ומידע על תאימות.

מדריך בחירה

Choose the MK2308S-1HILF when a 3.3 V system clock must fan out to eight destinations and low-skew, PLL-based zero-delay behavior is important. It is particularly appropriate for processors, FPGAs, parallel interfaces, memory-controller loads, and embedded subsystems operating within the documented 133 MHz limit. The alternate MK2308S-1HILFTR ordering code represents the same clock-buffer function and should be selected when the required assembly format differs. For designs needing only ordinary buffered fanout without zero-delay alignment, a conventional clock buffer may reduce complexity. Do not substitute a superficially similar eight-output device solely because it is also a 16-SOIC 133 MHz part; verify every pin, control input, supply connection, timing parameter, and output-loading limit before approval.

השוואה עם חלופות

פרמטר מוצר זה MK2308S-1HILFTR
Brand Renesas Electronics Renesas Electronics
Package 16-SOIC, 0.154 inch body width, 3.90 mm width 16-SOIC
Product Type PLL-based zero-delay buffer PLL-based zero-delay buffer
Maximum Clock Frequency 133 MHz 133 MHz
Supply Voltage 3.3 V 3.3 V
Number of Outputs 8 outputs 8 outputs
Input-to-Output Ratio 1:8 1:8
Output Type CMOS CMOS
PLL Bypass Supported Supported
Tri-State Output Supported Supported
Output Skew Low skew Low skew
Decoupling Requirement 0.01 mF at VDD and GND pins 4-5 and 13-12 0.01 mF at VDD and GND pins 4-5 and 13-12

מבדילים עיקריים

  • Eight-way zero-delay clock fanout (לעומתMK2308S-1HILFTR)
  • Integrated PLL bypass for diagnostic testing (לעומתMK2308S-1HILFTR)
  • Low-skew CMOS output architecture (לעומתMK2308S-1HILFTR)

הערות תכנון

Place the two specified 0.01 mF decoupling capacitors directly beside the MK2308S-1HILF VDD and GND pairs on pins 4-5 and 13-12. Keep each capacitor's power and ground connections short, with the ground return referenced to the same low-impedance plane used by the clock outputs. Minimize loop area and avoid routing clock traces between the capacitor and its supply pins. This placement limits supply transients that could otherwise affect PLL operation and output edge timing.

Use the manufacturer's suggested 33 ohm series termination resistor on each clock output when trace loading or impedance discontinuities can produce reflections. Place the resistor close to the output driver so it damps the outgoing edge rather than creating a second discontinuity at the receiver. Validate the selection with an eye diagram or time-domain measurement at the actual receiver. If reflections are absent, remove the resistor through schematic and layout review rather than retaining unverified termination.

Route all eight clock outputs as controlled-impedance traces over a continuous reference plane and avoid crossings with high-speed data or switching-power paths. Keep output lengths and via transitions consistent where low-skew operation is critical. Avoid stubs and test-point structures that create significant capacitive loading. Evaluate source, series, load, and receiver capacitance in the timing budget because the nominal 133 MHz limit alone does not guarantee acceptable edge quality in every physical implementation.

Do not confuse PLL bypass with zero-delay operation: bypass provides a direct input-to-output test path, while the PLL path supplies the documented low-skew zero-delay behavior. Also avoid treating the eight outputs as independent arbitrary-frequency clocks, because the function is an eight-way clock fanout with a 1:8 ratio. Verify enable and tri-state behavior, input slew requirements, and pin assignments in the manufacturer datasheet before using multiple output-enable states in a shared-clock architecture.

מידע על תאימות

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
נטול עופרת
Unknown
נטול הלוגנים
Unknown
מינרלים של סכסוך
Unknown

No explicit RoHS, REACH, lead-free, halogen-free, conflict-minerals, or automotive qualification statement was identified for this exact ordering code.

הנתונים אומתו בתאריך: 2026-11-10 — נתונים אומתו ונערכו על ידי צוות הנדסת הרכיבים של XAIPART

חיפושים קשורים

MK2308S-1HILF datasheet MK2308S-1HILF pinout MK2308S-1HILF datasheet pdf MK2308S-1HILF equivalent MK2308S-1HILF replacement MK2308S-1HILF cross reference MK2308S-1HILF price MK2308S-1HILF stock Renesas MK2308S-1HILF MK2308S-1HILF 16-SOIC MK2308S-1HILF 133MHz zero delay buffer MK2308S-1HILF vs MK2308S-1HILFTR

רכיבים ומונחים קשורים

Renesas Electronics MK2308S-1HILF MK2308S-1HILFTR zero-delay buffer ZDB clock buffer clock driver PLL-based clock buffer phase-locked loop PLL low-skew clock distribution low phase noise CMOS output tri-state output 133 MHz 3.3 V 1:8 fanout 16-SOIC SOIC package family surface-mount package clock fanout processor clock distribution FPGA clock distribution parallel communications interface memory controller
בקשת הצעת מחיר מהירה
מלא את כל הפרטים — צוות המכירות שלנו יגיב תוך 24 שעות
מספר חלק יצרן מארז QTY מחיר יעד סה"כ
✓
הצעת המחיר נשלחה!

נשיב לדוא"ל שלך בתוך 24 שעות

1
בקשת הצעת מחיר נשלחה
2
הצעת מחיר התקבלה
3
ההזמנה בוצעה
4
תשלום
5
נשלח
6
נמסר
צפה בפרטי בקשת הצעת המחיר