OPA131UJ - 4MHz Low-Power J-FET Op Amp | Texas Instruments
MPN: OPA131UJ ✓ সক্রিয়OPA131UJ সারাংশ
An operational amplifier, or op amp, is a voltage-controlled differential amplifier that uses high open-loop gain to amplify the difference between two input voltages. The OPA131 belongs to the FET-input op-amp category within the broader linear-amplifier and signal-conditioning hierarchy. Its J-FET input stage supports low input bias current, making it appropriate for sensors, measurement systems, and high-impedance sources where amplifier input current could otherwise create measurement error.
Key specifications include a 4 MHz gain-bandwidth product, 10 V/µs slew rate, 50 pA maximum input bias current, and approximately 750 µA power consumption. The input stage also provides low offset voltage and low offset drift, while the dynamic characteristics support accurate small-signal amplification. These characteristics make the OPA131UJ useful where low input loading, low power consumption, and stable amplification must coexist in an 8-pin SOIC footprint.
The single-amplifier architecture simplifies board routing compared with dual or quad devices when only one signal path is required. A typical noninverting configuration uses the non-inverting input as the signal terminal and the inverting input in the feedback network. The 4 MHz gain-bandwidth product supports useful closed-loop bandwidth into the hundreds of kilohertz, depending on noise gain and acceptable phase margin. The 10 V/µs slew rate provides additional headroom for larger output transitions and faster signal slewing.
OPA131UJ is suitable for sensor interfaces, buffered measurements, analog signal conditioning, audio and communications support circuits, and portable instrumentation. Its low 50 pA input bias current reduces loading on resistive sensors and high-output-impedance transducers. In battery-powered equipment, the approximately 750 µA power specification supports low-power acquisition systems when the required input signal bandwidth is modest.
Designers should verify the complete input and output common-mode ranges, output swing, noise performance, and stability limits against the circuit operating conditions before finalizing the feedback network. Place bypassing capacitors close to the supply pins and keep sensitive input traces short and away from switching nodes. If driving a capacitive load, use the manufacturer stability guidance and add isolation resistance when required.
This page combines the OPA131UJ electrical specifications, exact-ordering information, documented drop-in alternatives, comparison parameters, and practical PCB guidance to support faster component selection and implementation.
এর জন্য ড্রপ-ইন বিকল্প OPA131UJ — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।
এই সিরিজের ভ্যারিয়েন্ট
একই সিরিজের মডেল যেগুলো drop-in compatible OPA131UJ (একই form factor এবং footprint) — পার্থক্য রয়েছে Gain-Bandwidth Product, Number of Channels, Package, Slew Rate, Amplifier Type.
OPA131UA
✅ ড্রপ-ইনমূল্যের জন্য যোগাযোগ করুন
ডেটাশিট দেখুন →OPA131UJE4
✅ ড্রপ-ইন📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
OPA131UJ সর্বোচ্চ রেটিং ও বৈদ্যুতিক বৈশিষ্ট্য
| Amplifier Type | Single J-FET operational amplifier |
| Number of Channels | 1 circuit |
| Gain-Bandwidth Product | 4 MHz |
| Slew Rate | 10 V/µs |
| Maximum Input Bias Current | 50 pA |
| Power Consumption | 750 µA |
| Supply Voltage Range | ±4.5 V to ±18 V |
| Total Supply Voltage | 9 V to 36 V |
| Input Bias Current Type | FET input |
| প্যাকেজ | 8-pin SOIC |
| মাউন্টিং টাইপ | Surface mount |
OPA131UJ পিন কনফিগারেশন
| পিন 1 | NC — Not connected |
| পিন 2 | IN- — Inverting input |
| পিন 3 | IN+ — Non-inverting input |
| পিন 4 | V- — Negative supply connection |
| পিন 5 | NC — Not connected |
| পিন 6 | OUT — Output |
| পিন 7 | V+ — Positive supply connection |
| পিন 8 | NC — Not connected |
সাধারণ ব্যবহার
OPA131UJ এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: High-Impedance Sensor Interface, Portable Instrument Front End, Precision Analog Signal Conditioning, Low-Power Data Acquisition, Audio and Communications Buffering, Active Filter and Equalizer.
High-Impedance Sensor Interface
The OPA131UJ is appropriate for buffering high-output-impedance sensors because its J-FET input stage limits maximum input bias current to 50 pA. This reduces source loading compared with a bipolar-input amplifier and helps preserve sensor accuracy in measurement systems. With a 4 MHz gain-bandwidth product and 10 V/µs slew rate, it can amplify moderate-bandwidth sensor signals without requiring a high-power amplifier. Place the op amp close to the sensor interface, minimize input-trace length, and follow the manufacturer feedback and decoupling recommendations.
সুপারিশকৃত
Portable Instrument Front End
OPA131UJ supports portable instrumentation where amplifier power consumption must remain close to 750 µA while useful signal bandwidth is still required. Its 4 MHz gain-bandwidth product provides considerably more closed-loop capability than a very-low-bandwidth precision amplifier, and the 50 pA maximum input bias current reduces errors with high-impedance probes. Use the device as a preamplifier or impedance buffer, verify the common-mode limits for the selected battery rail, and place supply-bypass capacitors close to pins 4 and 7.
সুপারিশকৃত
Precision Analog Signal Conditioning
The OPA131UJ can condition low-level analog signals where input loading and dynamic response are both important. Its 50 pA maximum input bias current is suitable for high-resistance feedback networks and biased transducers, while the 4 MHz gain-bandwidth product supports moderate closed-loop gains with useful bandwidth margin. The 10 V/µs slew rate also helps preserve large-signal behavior. Select resistor values for acceptable noise gain and output swing, and confirm stability with the output load and compensation arrangement used in the final circuit.
সুপারিশকৃত
Low-Power Data Acquisition
OPA131UJ fits low-power data-acquisition blocks that require a low-noise input stage without the higher bias current of a conventional bipolar op amp. The approximately 750 µA power specification helps control system consumption, while the 4 MHz gain-bandwidth product accommodates higher-bandwidth sensor outputs than a precision-only amplifier. Use it ahead of an ADC when the source impedance is high or the acquisition rate is moderate. Keep input routing short, maintain a quiet ground return, and confirm that the selected gain remains stable with the ADC sampling network.
সুপারিশকৃত
Audio and Communications Buffering
OPA131UJ can serve as a general-purpose buffer in audio and communications signal paths where low input loading and adequate slew capability are needed. Its 50 pA maximum input bias current places little demand on a high-impedance source, and the 10 V/µs slew rate provides more headroom for waveform transitions than a low-bandwidth precision device. The 4 MHz gain-bandwidth product is suitable for intermediate-frequency or audio-support circuitry operating well below the amplifier's closed-loop bandwidth limit. Verify output swing, load capability, and noise performance in the completed signal chain.
সুপারিশকৃত
Active Filter and Equalizer
The OPA131UJ is appropriate for active-filter and equalizer stages requiring a FET input and higher bandwidth than a conventional precision op amp. Its 4 MHz gain-bandwidth product permits useful closed-loop bandwidth at moderate gain, and the 10 V/µs slew rate supports low-distortion transitions when operating within the output-voltage range. Use stable resistor and capacitor values, keep the feedback network compact, and check phase margin with the actual load. A dual OPA2131 can implement two coupled or independent filter channels when board space is constrained.
সুপারিশকৃত
সুপারিশকৃত পণ্যের সারসংক্ষেপ
এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা OPA131UJ — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।
নির্বাচন গাইড
বিকল্পের সাথে তুলনা
| পারামিটার | এই পণ্য | OPA131UA | OPA131UJE4 |
|---|---|---|---|
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Amplifier Configuration | Single amplifier | Single amplifier | Single amplifier |
| Input Stage | J-FET input | J-FET input | J-FET input |
| Gain-Bandwidth Product | 4 MHz | 4 MHz | 4 MHz |
| Slew Rate | 10 V/µs | 10 V/µs | 10 V/µs |
| Maximum Input Bias Current | 50 pA | 50 pA | 50 pA |
| Power Consumption | 750 µA | 750 µA | 750 µA |
| Supply Voltage Range | ±4.5 V to ±18 V | ±4.5 V to ±18 V | ±4.5 V to ±18 V |
| Ordering-Suffix Qualification | UJ | UA | UJE4 |
মূল পার্থক্যসমূহ
- Very low input bias current for a general-purpose 4 MHz amplifier (বনামOPA131UA)
- Low-power operation without sacrificing moderate signal bandwidth (বনামOPA131UJE4)
- Single-amplifier implementation in a compact 8-pin SOIC (বনামOPA2131)
ডিজাইন নোট
Route the two inputs, output, and supply connections to minimize parasitic capacitance and resistance. Place the input and output networks close to the SOIC leads, avoid long traces around pins 2 and 3, and connect the bypass capacitor directly between pins 4 and 7. A compact ground-return path is particularly important when the amplifier follows a high-impedance source because leakage through PCB contamination can otherwise exceed the very low input-bias-current contribution of the device.
Use the 4 MHz gain-bandwidth product and 10 V/µs slew rate as upper bounds, not guaranteed closed-loop operating points. At higher noise gain, available bandwidth and phase margin decrease. Simulate the feedback network with the actual source capacitance, load, and cable length, and follow the manufacturer's stability guidance when driving capacitive loads. This is especially important in sensor systems where long unshielded input leads can combine with probe capacitance to create an unintended oscillator or excessive peaking.
The approximately 750 µA power specification is a key advantage in portable measurement systems, but supply selection still determines usable input and output range. Verify that signal levels remain within the common-mode range and that output swing stays above the required load reference. Decouple each supply rail near the device, maintain a common ground reference between the sensor and amplifier, and avoid placing sensitive inputs near switching-regulator traces to prevent injected noise from reducing the benefit of the low-power FET input stage.
কমপ্লায়েন্স তথ্য
Compliance declarations are not stated in the cited product information. Confirm the applicable declarations with the manufacturer using the exact ordering suffix and current product documentation.