Texas Instruments

OPA131UJ - 4MHz Low-Power J-FET Op Amp | Texas Instruments

MPN: OPA131UJ ✓ 啟用中
±4.5 V to ±18 V Vdss 50 pA Id 8-pin SOIC Package
MOQ: 1 |

OPA131UJ 概覽

Texas Instruments OPA131UJ is a single, low-power J-FET input operational amplifier with a 4 MHz gain-bandwidth product, 10 V/µs slew rate, and 50 pA maximum input bias current, housed in an 8-pin SOIC package. It operates from ±4.5 V to ±18 V and is designed for instrumentation and general-purpose signal-chain applications.

An operational amplifier, or op amp, is a voltage-controlled differential amplifier that uses high open-loop gain to amplify the difference between two input voltages. The OPA131 belongs to the FET-input op-amp category within the broader linear-amplifier and signal-conditioning hierarchy. Its J-FET input stage supports low input bias current, making it appropriate for sensors, measurement systems, and high-impedance sources where amplifier input current could otherwise create measurement error.

Key specifications include a 4 MHz gain-bandwidth product, 10 V/µs slew rate, 50 pA maximum input bias current, and approximately 750 µA power consumption. The input stage also provides low offset voltage and low offset drift, while the dynamic characteristics support accurate small-signal amplification. These characteristics make the OPA131UJ useful where low input loading, low power consumption, and stable amplification must coexist in an 8-pin SOIC footprint.

The single-amplifier architecture simplifies board routing compared with dual or quad devices when only one signal path is required. A typical noninverting configuration uses the non-inverting input as the signal terminal and the inverting input in the feedback network. The 4 MHz gain-bandwidth product supports useful closed-loop bandwidth into the hundreds of kilohertz, depending on noise gain and acceptable phase margin. The 10 V/µs slew rate provides additional headroom for larger output transitions and faster signal slewing.

OPA131UJ is suitable for sensor interfaces, buffered measurements, analog signal conditioning, audio and communications support circuits, and portable instrumentation. Its low 50 pA input bias current reduces loading on resistive sensors and high-output-impedance transducers. In battery-powered equipment, the approximately 750 µA power specification supports low-power acquisition systems when the required input signal bandwidth is modest.

Designers should verify the complete input and output common-mode ranges, output swing, noise performance, and stability limits against the circuit operating conditions before finalizing the feedback network. Place bypassing capacitors close to the supply pins and keep sensitive input traces short and away from switching nodes. If driving a capacitive load, use the manufacturer stability guidance and add isolation resistance when required.

This page combines the OPA131UJ electrical specifications, exact-ordering information, documented drop-in alternatives, comparison parameters, and practical PCB guidance to support faster component selection and implementation.

直接替換替代品,適用於 OPA131UJ — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。

此系列的變體

與下列產品可直接替換的同系列型號: OPA131UJ (相同外形與佔位) — 差異在於 Gain-Bandwidth Product, Number of Channels, Package, Slew Rate, Amplifier Type.

Texas Instruments
Number of Channels: 1 channel
比較對象 OPA131UJ →
Texas Instruments
Gain-Bandwidth Product: 1 MHz
Number of Channels: 1 channel
Package: 8-SOIC, 0.154 in (3.90 mm) width
比較對象 OPA131UJ →

OPA131UA

✅ 直接替換
Texas Instruments
📦 SOIC-8
Single general-purpose FET-input operational amplifier · 1 channel · 4 MHz · 50 pA maximum · 750 µA · ±18 V · 10 V/µs · 750 µV maximum

聯絡詢價

查看資料表 →

OPA131UJE4

✅ 直接替換
📦 SOIC-8
Same OPA131 family, 8-pin SOIC footprint, and 4 MHz-class electrical positioning; E4 ordering-option qualification details require confirmation.

📋 參考替代品(不在目錄中)

OPA131UJ 最大額定值與電氣特性

Amplifier Type Single J-FET operational amplifier
Number of Channels 1 circuit
Gain-Bandwidth Product 4 MHz
Slew Rate 10 V/µs
Maximum Input Bias Current 50 pA
Power Consumption 750 µA
Supply Voltage Range ±4.5 V to ±18 V
Total Supply Voltage 9 V to 36 V
Input Bias Current Type FET input
封裝 8-pin SOIC
安裝類型 Surface mount

OPA131UJ 腳位配置

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
腳位 1 NC — Not connected
腳位 2 IN- — Inverting input
腳位 3 IN+ — Non-inverting input
腳位 4 V- — Negative supply connection
腳位 5 NC — Not connected
腳位 6 OUT — Output
腳位 7 V+ — Positive supply connection
腳位 8 NC — Not connected

典型應用

OPA131UJ 適用於 6 應用s: High-Impedance Sensor Interface, Portable Instrument Front End, Precision Analog Signal Conditioning, Low-Power Data Acquisition, Audio and Communications Buffering, Active Filter and Equalizer.

🧩

High-Impedance Sensor Interface

The OPA131UJ is appropriate for buffering high-output-impedance sensors because its J-FET input stage limits maximum input bias current to 50 pA. This reduces source loading compared with a bipolar-input amplifier and helps preserve sensor accuracy in measurement systems. With a 4 MHz gain-bandwidth product and 10 V/µs slew rate, it can amplify moderate-bandwidth sensor signals without requiring a high-power amplifier. Place the op amp close to the sensor interface, minimize input-trace length, and follow the manufacturer feedback and decoupling recommendations.

🖥️

Portable Instrument Front End

OPA131UJ supports portable instrumentation where amplifier power consumption must remain close to 750 µA while useful signal bandwidth is still required. Its 4 MHz gain-bandwidth product provides considerably more closed-loop capability than a very-low-bandwidth precision amplifier, and the 50 pA maximum input bias current reduces errors with high-impedance probes. Use the device as a preamplifier or impedance buffer, verify the common-mode limits for the selected battery rail, and place supply-bypass capacitors close to pins 4 and 7.

🏭

Precision Analog Signal Conditioning

The OPA131UJ can condition low-level analog signals where input loading and dynamic response are both important. Its 50 pA maximum input bias current is suitable for high-resistance feedback networks and biased transducers, while the 4 MHz gain-bandwidth product supports moderate closed-loop gains with useful bandwidth margin. The 10 V/µs slew rate also helps preserve large-signal behavior. Select resistor values for acceptable noise gain and output swing, and confirm stability with the output load and compensation arrangement used in the final circuit.

📡

Low-Power Data Acquisition

OPA131UJ fits low-power data-acquisition blocks that require a low-noise input stage without the higher bias current of a conventional bipolar op amp. The approximately 750 µA power specification helps control system consumption, while the 4 MHz gain-bandwidth product accommodates higher-bandwidth sensor outputs than a precision-only amplifier. Use it ahead of an ADC when the source impedance is high or the acquisition rate is moderate. Keep input routing short, maintain a quiet ground return, and confirm that the selected gain remains stable with the ADC sampling network.

🌐

Audio and Communications Buffering

OPA131UJ can serve as a general-purpose buffer in audio and communications signal paths where low input loading and adequate slew capability are needed. Its 50 pA maximum input bias current places little demand on a high-impedance source, and the 10 V/µs slew rate provides more headroom for waveform transitions than a low-bandwidth precision device. The 4 MHz gain-bandwidth product is suitable for intermediate-frequency or audio-support circuitry operating well below the amplifier's closed-loop bandwidth limit. Verify output swing, load capability, and noise performance in the completed signal chain.

🎧

Active Filter and Equalizer

The OPA131UJ is appropriate for active-filter and equalizer stages requiring a FET input and higher bandwidth than a conventional precision op amp. Its 4 MHz gain-bandwidth product permits useful closed-loop bandwidth at moderate gain, and the 10 V/µs slew rate supports low-distortion transitions when operating within the output-voltage range. Use stable resistor and capacitor values, keep the feedback network compact, and check phase margin with the actual load. A dual OPA2131 can implement two coupled or independent filter channels when board space is constrained.

推薦產品摘要

OPA131 Single-channel family member with the same core architecture 用於: High-Impedance Sensor Interface, Portable Instrument Front End, Precision Analog Signal Conditioning, Low-Power Data Acquisition, Audio and Communications Buffering, Active Filter and Equalizer OPA2131 Dual-channel family option for two sensor channels 用於: High-Impedance Sensor Interface, Portable Instrument Front End, Precision Analog Signal Conditioning, Low-Power Data Acquisition, Audio and Communications Buffering, Active Filter and Equalizer OPA4131 Quad-channel family option for multi-sensor acquisition 用於: High-Impedance Sensor Interface, Precision Analog Signal Conditioning, Low-Power Data Acquisition, Audio and Communications Buffering
What is the key specification of the OPA131UJ?
The OPA131UJ is a single J-FET operational amplifier with a 4 MHz gain-bandwidth product, 10 V/µs slew rate, 50 pA maximum input bias current, and approximately 750 µA power consumption. According to the Texas Instruments OPAx131 datasheet, the device is packaged in an 8-pin SOIC and operates from ±4.5 V to ±18 V. Its combination of low input bias current, low power consumption, and good dynamic performance makes it appropriate for instrumentation, sensor interfaces, and general-purpose analog signal conditioning.
What is the operating voltage range of OPA131UJ?
The OPA131UJ operates from ±4.5 V to ±18 V, corresponding to a total supply range of 9 V to 36 V. According to the Texas Instruments OPAx131 datasheet, this range supports both single-supply and split-supply operation when the circuit design uses the rails appropriately. Designers must also confirm that the signal and output remain inside the amplifier's input common-mode and output-swing limits.
Why is the 50 pA input bias current of OPA131UJ important?
The 50 pA maximum input bias current makes OPA131UJ suitable for high-impedance sensors because it minimizes the current drawn from the source. For example, a 1 GΩ source produces approximately 50 mV of shift from 50 pA, making input bias current much more important than amplifier offset in some high-impedance measurements. The Texas Instruments OPAx131 datasheet identifies the OPA131UJ as a FET-input device, and its 4 MHz bandwidth provides useful signal speed without requiring a high-power bipolar amplifier.
Is OPA131UJ suitable for low-power instrumentation?
Yes, OPA131UJ is suitable for low-power instrumentation because its power consumption is approximately 750 µA. The low-bias FET input stage also supports high-impedance sensor interfaces without the higher input currents common to many bipolar input op amps. According to the Texas Instruments OPAx131 datasheet, the 4 MHz gain-bandwidth product and 10 V/µs slew rate provide adequate dynamic performance for many precision and general-purpose measurement circuits operating at modest bandwidth.
Where can I download the OPA131UJ datasheet PDF?
The official OPA131UJ datasheet PDF is available from the Texas Instruments product page at https://www.ti.com/lit/ds/symlink/opa131.pdf. The document covers the OPA131, OPA2131, and OPA4131 FET-input operational-amplifier family and includes ordering information, electrical characteristics, pin configuration, and application guidance. Use the OPA131UJ ordering table to confirm package and temperature-grade options before placing a design into production.
Where can I find the OPA131UJ pinout?
The OPA131UJ pin configuration is shown in the pin-configuration section of the Texas Instruments OPAx131 datasheet. The device uses an industry-standard 8-pin SOIC footprint with a single operational amplifier. When assigning PCB tracks, use the numbered pin diagram in the datasheet and preserve the exposed functionality of each pin, including power, input, output, and no-connect positions.
How does OPA131UJ compare with OPA131UA?
OPA131UJ and OPA131UA are closely related orderable versions of the same single-channel OPA131 family in the 8-pin SOIC package. The electrically meaningful parameters remain aligned closely enough for footprint-compatible design use, but ordering suffixes should be checked against the required temperature grade and manufacturing conditions. According to the Texas Instruments OPA131 product information, the OPA131 family provides 4 MHz bandwidth, 50 pA bias current, and approximately 750 µA power consumption.
What is the best drop-in replacement for OPA131UJ?
OPA131UA is the closest documented drop-in candidate for OPA131UJ because it belongs to the same single-channel OPA131 family and uses the same 8-pin SOIC footprint. OPA131UJE4 is another documented ordering option in the same package family. Confirm the required temperature range, production configuration, and electrical characteristics in the Texas Instruments ordering table before substituting either part; the cross-reference records do not establish identical qualification status for every suffix.
Can OPA131UJ replace OPA131UA in an existing circuit?
OPA131UJ can replace OPA131UA where the existing PCB uses the same 8-pin SOIC footprint and the required electrical and temperature conditions remain acceptable. Both parts are members of the Texas Instruments OPA131 single FET-input amplifier family, which has a 4 MHz gain-bandwidth product and 10 V/µs slew rate. Check the exact suffix definitions, operating temperature, and qualification requirements before approving the substitution.
When should I choose OPA131UJ over a lower-bandwidth op amp?
Choose OPA131UJ when the signal path needs more than the bandwidth of a general-purpose low-power amplifier while retaining a 50 pA maximum input bias current. Its 4 MHz gain-bandwidth product provides substantially more closed-loop bandwidth than a typical megahertz-class precision op amp, while approximately 750 µA power consumption remains appropriate for portable measurement systems. This balance is useful for sensor conditioning where source impedance is high and signal bandwidth exceeds the capability of very-low-power alternatives.
Is OPA131UJ suitable for sensor signal conditioning?
OPA131UJ is well suited to sensor signal conditioning because its 50 pA maximum input bias current limits loading on high-impedance sources. The 4 MHz gain-bandwidth product also supports faster closed-loop operation than a typical precision amplifier optimized only for offset and drift. According to the Texas Instruments OPAx131 datasheet, the device also has a 10 V/µs slew rate and approximately 750 µA power consumption, making it a practical choice for portable sensor interfaces.
What are the key specifications engineers should know about OPA131UJ?
The OPA131UJ combines a 4 MHz gain-bandwidth product, 10 V/µs slew rate, 50 pA maximum input bias current, and approximately 750 µA power consumption in an 8-pin SOIC package. According to the Texas Instruments OPAx131 datasheet, its supply range is ±4.5 V to ±18 V. These figures define its main design envelope: low source loading, moderate speed, low power consumption, and support for both single- and split-supply architectures.
What can replace OPA131UJ in a pin-compatible design?
OPA131UA and OPA131UJE4 are the documented pin-compatible choices from the Texas Instruments OPA131 family for an OPA131UJ design. Both use the 8-pin SOIC footprint, allowing the same PCB land pattern to be used, subject to suffix-specific temperature and production requirements. The 4 MHz gain-bandwidth product and 10 V/µs slew rate remain associated with the OPAx131 family, making these options preferable to devices requiring a different package or pin assignment.
Where can I buy OPA131UJ online?
Use the Request a Quote form on this page to request OPA131UJ pricing, stock confirmation, minimum order quantity, and lead time for the exact 8-pin SOIC ordering configuration. Because component availability and commercial terms can change, a current quotation provides the most reliable purchasing response. Include the target quantity, acceptable packaging, and any required temperature or manufacturing qualifications in the request.
What is the price and lead time for OPA131UJ?
Request the current OPA131UJ price, stock position, minimum order quantity, and lead time through the Request a Quote form on this page. Commercial terms depend on quantity, package configuration, and current channel availability, so they should be confirmed before committing a production schedule. The exact ordering suffix should be stated on the request to avoid ambiguity with other OPA131 package or temperature options.
Is OPA131UJ in stock?
Use the Request a Quote form on this page for a current OPA131UJ stock confirmation. The manufacturer product page and distributor search result support locating the part, but stock quantity can change with order volume and purchasing conditions. Include your required quantity and packaging preference so the response can address the exact OPA131UJ configuration rather than merely confirming that the family is generally available.

工程參考資料,適用於 OPA131UJ — 比較、設計指引及合規資訊。

選型指南

Choose OPA131UJ for single-channel instrumentation, sensor buffering, and general-purpose analog conditioning where low input bias current, a 4 MHz gain-bandwidth product, 10 V/µs slew rate, and approximately 750 µA power consumption are important. OPA131UA is the closest same-family option when its ordering suffix meets the required temperature and production conditions while retaining the same 8-pin SOIC footprint. OPA131UJE4 is another pin-compatible family option for designs whose qualification and ordering requirements match that suffix. OPA2131 is preferable when two amplifiers are needed, while OPA4131 minimizes package count for four channels. Before finalizing any substitution, verify supply range, input common-mode limits, output swing, operating temperature, qualification status, and stability with the actual load.

與替代品比較

參數 本產品 OPA131UA OPA131UJE4
Package 8-pin SOIC 8-pin SOIC 8-pin SOIC
Brand Texas Instruments Texas Instruments Texas Instruments
Amplifier Configuration Single amplifier Single amplifier Single amplifier
Input Stage J-FET input J-FET input J-FET input
Gain-Bandwidth Product 4 MHz 4 MHz 4 MHz
Slew Rate 10 V/µs 10 V/µs 10 V/µs
Maximum Input Bias Current 50 pA 50 pA 50 pA
Power Consumption 750 µA 750 µA 750 µA
Supply Voltage Range ±4.5 V to ±18 V ±4.5 V to ±18 V ±4.5 V to ±18 V
Ordering-Suffix Qualification UJ UA UJE4

主要差異化特點

  • Very low input bias current for a general-purpose 4 MHz amplifier (對比OPA131UA)
  • Low-power operation without sacrificing moderate signal bandwidth (對比OPA131UJE4)
  • Single-amplifier implementation in a compact 8-pin SOIC (對比OPA2131)

設計說明

Route the two inputs, output, and supply connections to minimize parasitic capacitance and resistance. Place the input and output networks close to the SOIC leads, avoid long traces around pins 2 and 3, and connect the bypass capacitor directly between pins 4 and 7. A compact ground-return path is particularly important when the amplifier follows a high-impedance source because leakage through PCB contamination can otherwise exceed the very low input-bias-current contribution of the device.

Use the 4 MHz gain-bandwidth product and 10 V/µs slew rate as upper bounds, not guaranteed closed-loop operating points. At higher noise gain, available bandwidth and phase margin decrease. Simulate the feedback network with the actual source capacitance, load, and cable length, and follow the manufacturer's stability guidance when driving capacitive loads. This is especially important in sensor systems where long unshielded input leads can combine with probe capacitance to create an unintended oscillator or excessive peaking.

The approximately 750 µA power specification is a key advantage in portable measurement systems, but supply selection still determines usable input and output range. Verify that signal levels remain within the common-mode range and that output swing stays above the required load reference. Decouple each supply rail near the device, maintain a common ground reference between the sensor and amplifier, and avoid placing sensitive inputs near switching-regulator traces to prevent injected noise from reducing the benefit of the low-power FET input stage.

合規資訊

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
無鉛
Unknown
無鹵
Unknown
衝突礦產
Unknown

Compliance declarations are not stated in the cited product information. Confirm the applicable declarations with the manufacturer using the exact ordering suffix and current product documentation.

資料驗證日期: 2026-11-19 — 資料由 XAIPART 元件工程團隊驗證及整理

相關搜尋

OPA131UJ datasheet OPA131UJ specifications OPA131UJ pinout OPA131UJ datasheet pdf OPA131UJ SOIC-8 OPA131UJ 4MHz OPA131UJ 50pA bias current OPA131UJ equivalent OPA131UJ replacement OPA131UJ vs OPA131UA OPA131UJ price OPA131UJ stock

相關元件與詞彙

Texas Instruments OPA131UJ OPA131 OPA2131 OPA4131 OPA131UA OPA131UJE4 operational amplifier single operational amplifier J-FET input FET-input amplifier instrumentation amplifier signal conditioning gain-bandwidth product input bias current slew rate power consumption common-mode voltage SOIC-8 surface-mount package high-impedance sensor portable instrumentation low-power data acquisition active filter feedback network
快速報價 RFQ
請填寫完整詳細資料 — 我們的業務團隊將於 24 小時內回覆
料號 製造商 封裝 QTY 目標價格 小計
✓
報價已提交!

我們將於 24 小時內回覆您的電子郵件

1
詢價已提交
2
已收到報價
3
已下單
4
付款
5
已出貨
6
已送達
檢視詢價單詳情