OPA337PA - 5.5V, 3MHz RRO Op Amp | Texas Instruments
MPN: OPA337PA ✓ সক্রিয়OPA337PA সারাংশ
An operational amplifier is an active analog building block that amplifies the voltage difference between its inverting and non-inverting inputs. OPA337PA belongs to the broader hierarchy of operational amplifier, analog amplifier, amplifier IC, and semiconductor. Its rail-to-rail output stage is useful when the required output voltage must approach a supply rail, while its CMOS construction and FET input stage support low-leakage signal acquisition. These characteristics make the device relevant to sensor conditioning, current-to-voltage conversion, buffering, filtering, and general low-voltage instrumentation.
The primary specified performance figures are a 3 MHz gain-bandwidth product, a 5.5 V maximum supply, one amplifier per package, and a 3 MHz operating speed described for the OPA337 family. The family also supports single-supply operation and provides a rail-to-rail output swing. These features allow OPA337PA to serve as the active element in gain, filtering, and signal-conditioning stages where the signal remains within the device's specified operating limits.
OPA337PA uses a FET-input, single-supply CMOS design. FET inputs are especially appropriate when the source impedance is high and input bias current must remain low, while single-supply operation simplifies circuits that operate from one positive rail and ground. The rail-to-rail output improves usable output range, but the application must still preserve adequate output headroom for the required load and operating conditions.
Typical uses include buffering sensor outputs, amplifying low-level analog signals, active low-pass filters, transimpedance amplifiers, audio and control-signal interfaces, and general laboratory or industrial measurement circuits. The 8-pin PDIP format is particularly convenient for prototypes and through-hole assemblies where compactness is secondary to easy manual soldering and inspection.
Designers should begin by confirming the intended supply, input common-mode range, output swing, stability configuration, and load drive against the manufacturer datasheet. Stable feedback ratios and suitable source impedances are essential for reliable closed-loop operation. Decoupling close to the supply pins and careful routing of high-impedance input nodes are recommended because board leakage and parasitic capacitance can degrade precision measurements.
This product record combines the OPA337PA family specifications, package identification, sourcing guidance, comparison data, and application-oriented design notes. It is intended to help engineers move from the 5.5 V, 3 MHz, rail-to-rail-output operating concept to a practical 8-pin PDIP implementation while recognizing the checks required for reliable analog performance.
এর জন্য ড্রপ-ইন বিকল্প OPA337PA — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।
OPA337UA
✅ ড্রপ-ইন📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
OPA337PA সর্বোচ্চ রেটিং ও বৈদ্যুতিক বৈশিষ্ট্য
| Amplifier Type | General-purpose operational amplifier (category) |
| Number of Channels | 1 circuit (count) |
| Maximum Supply Voltage | 5.5 V |
| Gain-Bandwidth Product | 3 MHz |
| Output Architecture | Rail-to-rail output (architecture) |
| Supply Configuration | Single-supply operation (configuration) |
| Input Stage | FET input (architecture) |
| Maximum Input Bias Current | 10 pA |
| Process Technology | CMOS (process) |
| প্যাকেজ | 8-PDIP (package) |
| পিন সংখ্যা | 8 pins (count) |
| মাউন্টিং টাইপ | Through-hole (mounting) |
OPA337PA 8-pdip (package) পিন কনফিগারেশন গাইড
OPA337PA (8-pdip (package) প্যাকেজ)-এর পিন কনফিগারেশন। এই অ্যানালগ কম্পোনেন্টে ইনপুট, আউটপুট ও পাওয়ার সাপ্লাই পিন রয়েছে। অফসেট নাল, কম্পেনসেশন ও এনেবল পিন কনফিগারেশনের জন্য প্রস্তুতকারকের ডেটাশিট দেখুন। সিগন্যাল কন্ডিশনিং ও অ্যামপ্লিফায়ার সার্কিটের জন্য আদর্শ।
এর জন্য বিস্তারিত পিনআউট ডেটা পাওয়া যায়নি OPA337PA.
দেখুন ডেটাশিট সম্পূর্ণ পিন কনফিগারেশনের জন্য।
সাধারণ ব্যবহার
OPA337PA এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Sensor Signal Conditioning, Transimpedance Amplification, Active Low-Pass Filtering, Audio and Control-Signal Interfaces, Portable Measurement Equipment, General-Purpose Analog Prototyping.
Sensor Signal Conditioning
OPA337PA is appropriate for amplifying or buffering sensor signals when the design uses a low-voltage single supply and needs low input leakage. Its FET-input stage can limit the bias-current burden on high-impedance sources, while the 3 MHz gain-bandwidth product provides useful closed-loop bandwidth for moderate-speed signals. The rail-to-rail output also helps maximize signal range in compact instrumentation. Before finalizing the circuit, verify the required common-mode range and output swing against the manufacturer datasheet.
সুপারিশকৃত
Transimpedance Amplification
OPA337PA can serve as the active device in a transimpedance stage for photodiode or other current-output sensors. The 10 pA maximum input bias current figure associated with the family is useful when source leakage can materially affect the measured current, and the 3 MHz gain-bandwidth product supports higher-bandwidth photodiode designs than a very slow general-purpose amplifier. The feedback resistor and compensation capacitor must be selected together, and the datasheet should be consulted for complete stability guidance.
সুপারিশকৃত
Active Low-Pass Filtering
OPA337PA is suitable for an active low-pass filter when the signal bandwidth is modest and a single 5.5 V-class supply is preferred. A 3 MHz gain-bandwidth product leaves bandwidth available for closed-loop gain and filter operation, while the rail-to-rail output can improve dynamic range. Stable operation depends on the selected noise gain, source impedance, and capacitive loading. Use the manufacturer's recommended compensation and feedback arrangements, and prototype the final resistor and capacitor values before production release.
সুপারিশকৃত
Audio and Control-Signal Interfaces
OPA337PA can be used for low-level audio or control-signal amplification in compact single-supply systems. The rail-to-rail output stage is useful for driving the next stage through a limited voltage range, and the 3 MHz gain-bandwidth product is more than adequate for many control and baseband audio functions. Its CMOS implementation adds another option for portable equipment where low supply voltage and compactness are important. Confirm output-current capability, output swing, and stability at the selected gain before loading the output.
সুপারিশকৃত
Portable Measurement Equipment
OPA337PA fits portable measurement equipment that combines a single positive supply, analog signal conditioning, and an 8-pin PDIP construction. The package is convenient for educational, laboratory, and service designs where through-hole assembly and manual inspection remain important. The rail-to-rail output and FET-input stage can support low-voltage signal paths, but battery-operated systems should also examine supply-current limits not explicitly established by the basic product summary. Validate offset, drift, noise, and input-range behavior against the exact datasheet limits.
সুপারিশকৃত
General-Purpose Analog Prototyping
OPA337PA is a useful general-purpose amplifier for breadboard and through-hole prototype boards because it combines a familiar 8-pin PDIP format with low-voltage single-supply operation. It can test gain stages, buffers, comparators, and simple active networks before a design is converted to a smaller surface-mount package. The 3 MHz gain-bandwidth product supports moderate-frequency experiments, while rail-to-rail output simplifies debugging near supply limits. Always include supply bypassing and confirm the feedback topology is stable for the intended load.
সুপারিশকৃত
এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা OPA337PA — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।
নির্বাচন গাইড
বিকল্পের সাথে তুলনা
| পারামিটার | এই পণ্য | OPA337UA |
|---|---|---|
| Brand | Texas Instruments | Texas Instruments |
| Package | 8-PDIP | PDIP-8 - through-hole |
মূল পার্থক্যসমূহ
- Combines a 3 MHz gain-bandwidth product with a 5.5 V maximum supply (বনামOPA337UA)
- Uses a rail-to-rail output stage (বনামOPA337UA)
- FET-input architecture with 10 pA maximum input bias current (বনামOPA337UA)
ডিজাইন নোট
Place the supply-decoupling capacitor close to the amplifier's supply and ground connections, and keep the return path short to reduce trace inductance. For high-impedance sensor inputs, minimize exposed PCB area around each input, avoid nearby switching nodes, and use a guarded ground where appropriate. The 8-pin PDIP layout provides generous spacing for through-hole construction, but analog input and output traces should still be routed away from digital switching paths.
Do not assume that a rail-to-rail output reaches the supply rail under every load. Check the manufacturer output-swing characteristics at the intended supply voltage and load current. Likewise, single-supply operation does not make every input voltage legal: verify the common-mode input range before applying signals near ground. Use stable feedback ratios and the manufacturer's guidance when driving capacitive loads or operating at high closed-loop gain.
For source impedances above a few kilohms, account for amplifier input bias current, PCB leakage, and input capacitance before choosing the closed-loop bandwidth. In a transimpedance stage, select the feedback resistor and compensation capacitor as a matched pair rather than treating them independently. Prototype with the intended source and load because parasitics can change phase margin even when the nominal resistor values appear correct.
কমপ্লায়েন্স তথ্য
No explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals declarations were identified for OPA337PA. AEC-Q100 is not applicable to this general-purpose operational amplifier.