Texas Instruments

OPA337PA - 5.5V, 3MHz RRO Op Amp | Texas Instruments

MPN: OPA337PA ✓ فعال
5.5 V Vdss 10 pA Id 8-PDIP (package) Package
MOQ: 1 |

OPA337PA جائزہ

Texas Instruments OPA337PA is a single general-purpose CMOS operational amplifier designed for low-cost and miniature signal-processing circuits. It supports a 5.5 V maximum supply, provides a 3 MHz gain-bandwidth product, and uses a rail-to-rail output architecture. The device is supplied in an 8-pin PDIP through-hole package, making it suitable for conventional PCB layouts, educational instruments, instrumentation, and low-voltage analog systems that do not require the smallest surface-mount footprint.

An operational amplifier is an active analog building block that amplifies the voltage difference between its inverting and non-inverting inputs. OPA337PA belongs to the broader hierarchy of operational amplifier, analog amplifier, amplifier IC, and semiconductor. Its rail-to-rail output stage is useful when the required output voltage must approach a supply rail, while its CMOS construction and FET input stage support low-leakage signal acquisition. These characteristics make the device relevant to sensor conditioning, current-to-voltage conversion, buffering, filtering, and general low-voltage instrumentation.

The primary specified performance figures are a 3 MHz gain-bandwidth product, a 5.5 V maximum supply, one amplifier per package, and a 3 MHz operating speed described for the OPA337 family. The family also supports single-supply operation and provides a rail-to-rail output swing. These features allow OPA337PA to serve as the active element in gain, filtering, and signal-conditioning stages where the signal remains within the device's specified operating limits.

OPA337PA uses a FET-input, single-supply CMOS design. FET inputs are especially appropriate when the source impedance is high and input bias current must remain low, while single-supply operation simplifies circuits that operate from one positive rail and ground. The rail-to-rail output improves usable output range, but the application must still preserve adequate output headroom for the required load and operating conditions.

Typical uses include buffering sensor outputs, amplifying low-level analog signals, active low-pass filters, transimpedance amplifiers, audio and control-signal interfaces, and general laboratory or industrial measurement circuits. The 8-pin PDIP format is particularly convenient for prototypes and through-hole assemblies where compactness is secondary to easy manual soldering and inspection.

Designers should begin by confirming the intended supply, input common-mode range, output swing, stability configuration, and load drive against the manufacturer datasheet. Stable feedback ratios and suitable source impedances are essential for reliable closed-loop operation. Decoupling close to the supply pins and careful routing of high-impedance input nodes are recommended because board leakage and parasitic capacitance can degrade precision measurements.

This product record combines the OPA337PA family specifications, package identification, sourcing guidance, comparison data, and application-oriented design notes. It is intended to help engineers move from the 5.5 V, 3 MHz, rail-to-rail-output operating concept to a practical 8-pin PDIP implementation while recognizing the checks required for reliable analog performance.

کے لیے ڈراپ اِن متبادل OPA337PA — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔

OPA337UA

✅ ڈراپ-اِن
📦 PDIP-8
Same-family MICROAMPLIFIER device in a through-hole DIP package; suffix-specific temperature-grade and electrical-limit differences require final datasheet confirmation.

📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)

OPA337PA زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات

Amplifier Type General-purpose operational amplifier (category)
Number of Channels 1 circuit (count)
Maximum Supply Voltage 5.5 V
Gain-Bandwidth Product 3 MHz
Output Architecture Rail-to-rail output (architecture)
Supply Configuration Single-supply operation (configuration)
Input Stage FET input (architecture)
Maximum Input Bias Current 10 pA
Process Technology CMOS (process)
پیکیج 8-PDIP (package)
پن کی تعداد 8 pins (count)
ماؤنٹنگ ٹائپ Through-hole (mounting)

OPA337PA 8-pdip (package) پن کنفیگریشن گائیڈ

OPA337PA (8-pdip (package) پیکیج) کے لیے پن کنفیگریشن۔ اس اینالاگ کمپوننٹ میں اِن پٹ، آؤٹ پٹ اور پاور سپلائی پنز شامل ہیں۔ آفسیٹ نل، کمپنسیشن اور اِن ایبل پن کنفیگریشنز کے لیے مینوفیکچرر کے ڈیٹا شیٹ سے رجوع کریں۔ سگنل کنڈیشننگ اور ایمپلیفائر سرکٹس کے لیے مثالی۔

OPA337PA کے لیے 8-pdip (package) پیکیج پن آؤٹ ڈایاگرام

کے لیے تفصیلی پن آؤٹ ڈیٹا دستیاب نہیں OPA337PA.

رجوع کریں ڈیٹا شیٹ مکمل پن کنفیگریشن کے لیے۔

عام استعمالات

OPA337PA کے لیے موزوں ہے 6 ایپلیکیشنs: Sensor Signal Conditioning, Transimpedance Amplification, Active Low-Pass Filtering, Audio and Control-Signal Interfaces, Portable Measurement Equipment, General-Purpose Analog Prototyping.

🧩

Sensor Signal Conditioning

OPA337PA is appropriate for amplifying or buffering sensor signals when the design uses a low-voltage single supply and needs low input leakage. Its FET-input stage can limit the bias-current burden on high-impedance sources, while the 3 MHz gain-bandwidth product provides useful closed-loop bandwidth for moderate-speed signals. The rail-to-rail output also helps maximize signal range in compact instrumentation. Before finalizing the circuit, verify the required common-mode range and output swing against the manufacturer datasheet.

📷

Transimpedance Amplification

OPA337PA can serve as the active device in a transimpedance stage for photodiode or other current-output sensors. The 10 pA maximum input bias current figure associated with the family is useful when source leakage can materially affect the measured current, and the 3 MHz gain-bandwidth product supports higher-bandwidth photodiode designs than a very slow general-purpose amplifier. The feedback resistor and compensation capacitor must be selected together, and the datasheet should be consulted for complete stability guidance.

🌐

Active Low-Pass Filtering

OPA337PA is suitable for an active low-pass filter when the signal bandwidth is modest and a single 5.5 V-class supply is preferred. A 3 MHz gain-bandwidth product leaves bandwidth available for closed-loop gain and filter operation, while the rail-to-rail output can improve dynamic range. Stable operation depends on the selected noise gain, source impedance, and capacitive loading. Use the manufacturer's recommended compensation and feedback arrangements, and prototype the final resistor and capacitor values before production release.

🎧

Audio and Control-Signal Interfaces

OPA337PA can be used for low-level audio or control-signal amplification in compact single-supply systems. The rail-to-rail output stage is useful for driving the next stage through a limited voltage range, and the 3 MHz gain-bandwidth product is more than adequate for many control and baseband audio functions. Its CMOS implementation adds another option for portable equipment where low supply voltage and compactness are important. Confirm output-current capability, output swing, and stability at the selected gain before loading the output.

📱

Portable Measurement Equipment

OPA337PA fits portable measurement equipment that combines a single positive supply, analog signal conditioning, and an 8-pin PDIP construction. The package is convenient for educational, laboratory, and service designs where through-hole assembly and manual inspection remain important. The rail-to-rail output and FET-input stage can support low-voltage signal paths, but battery-operated systems should also examine supply-current limits not explicitly established by the basic product summary. Validate offset, drift, noise, and input-range behavior against the exact datasheet limits.

🔧

General-Purpose Analog Prototyping

OPA337PA is a useful general-purpose amplifier for breadboard and through-hole prototype boards because it combines a familiar 8-pin PDIP format with low-voltage single-supply operation. It can test gain stages, buffers, comparators, and simple active networks before a design is converted to a smaller surface-mount package. The 3 MHz gain-bandwidth product supports moderate-frequency experiments, while rail-to-rail output simplifies debugging near supply limits. Always include supply bypassing and confirm the feedback topology is stable for the intended load.

What are the key specifications of OPA337PA that engineers should know?
OPA337PA is a single general-purpose CMOS operational amplifier with a 5.5 V maximum supply, 3 MHz gain-bandwidth product, rail-to-rail output, and 8-pin PDIP package. According to the manufacturer product page, the OPA337 family is intended for low-cost and miniature applications. Its FET-input architecture, single-supply operation, and through-hole package make it practical for low-voltage instrumentation, sensor conditioning, buffering, and general analog signal-processing boards.
What is the operating voltage of OPA337PA?
OPA337PA supports operation up to a 5.5 V maximum supply. The manufacturer identifies the OPA337 as a 5.5 V, 3 MHz rail-to-rail-output operational amplifier and confirms that the family supports single-supply operation. The exact minimum supply, input range, and output-swing limits should be taken from the manufacturer datasheet when designing bias points, headroom, and supply sequencing for a particular circuit.
Where can I download the OPA337PA datasheet PDF?
The official OPA337PA datasheet can be accessed through the Texas Instruments OPA337 product page at https://www.ti.com/product/OPA337. That page provides family-level technical information and links to the manufacturer documentation. A separate OPA337PA PDF is also listed at https://pdf.digi-electronics.com/pdf/2579/OPA337PA-datasheet.pdf. Use the manufacturer document as the controlling reference for pin functions, electrical limits, and application guidance.
Where can I find the OPA337PA pinout?
The OPA337PA pinout is defined for its 8-pin PDIP package by the Texas Instruments OPA337 datasheet. Use the pin-description table and package drawing on the official product page at https://www.ti.com/product/OPA337. The OPA337PA has eight pins, but their individual names and electrical functions are not reproduced here because a manufacturer-authoritative pin table was not available for transcription.
Is OPA337PA suitable for single-supply operation?
Yes, OPA337PA supports single-supply operation as part of the OPA337 CMOS amplifier family. The rail-to-rail output architecture is especially useful in circuits powered from a positive rail and ground, but the actual usable signal range still depends on input common-mode limits, output swing, supply voltage, and load. Consult the manufacturer datasheet before choosing bias voltages or operating close to either supply rail.
What can replace OPA337PA?
OPA337UA is the closest documented same-family replacement candidate because the manufacturer-series comparison identifies it alongside OPA337PA and both belong to the MICROAMPLIFIER family. OPA337UA is available in a through-hole DIP format, making it mechanically relevant to an 8-pin PDIP design. Its electrical parameters and ordering suffix should still be checked against the OPA337PA datasheet before production substitution.
Can OPA337UA replace OPA337PA?
OPA337UA can be evaluated as a same-family replacement for OPA337PA because both are listed as MICROAMPLIFIER series devices and the documented comparison associates them with through-hole packages. Confirm that the exact suffix offers the same pinout, supply range, gain-bandwidth product, and intended temperature grade. Treat OPA337UA as a conditional replacement until its manufacturer datasheet and package drawing have been compared directly.
OPA337PA vs OPA337UA - which is better for a through-hole design?
OPA337PA is the primary choice when the exact listed 8-PDIP configuration and its associated ordering information are required. OPA337UA is a same-family alternative for a through-hole design, and the documented comparison describes OPA337UA as a high-performance amplifier with ultra-low leakage current. The deciding factors are exact temperature grade, suffix-specific electrical limits, and whether the required operating conditions fall within the selected part's guaranteed limits.
When should I choose OPA337PA over OPA337UA?
Choose OPA337PA when the exact 8-PDIP ordering option and its manufacturer documentation are required for a new design or controlled replacement. Choose OPA337UA only after confirming equivalent pin behavior and application limits for the operating condition. Both options are relevant to through-hole assemblies, but suffix-specific electrical characteristics, temperature grade, and lifecycle requirements can make one preferable even when the packages appear interchangeable.
Is OPA337PA suitable for sensor and instrumentation applications?
OPA337PA is suitable for many low-voltage sensor and instrumentation circuits because it combines a 3 MHz gain-bandwidth product, FET inputs, single-supply operation, and rail-to-rail output. Its 8-pin PDIP package is convenient for through-hole prototype boards and laboratory instruments. High-impedance sources still require guarded layout, clean grounding, suitable bias resistors, and verification of input bias-current and common-mode requirements.
Where can I buy OPA337PA online?
Use the Request a Quote form on this page to request OPA337PA availability, current commercial terms, and the appropriate order quantity. The part is listed as an 8-PDIP single-circuit rail-to-rail general-purpose amplifier. This page does not publish a static commercial figure because pricing and inventory can change; the quote form provides the current purchasing channel for the exact OPA337PA suffix.
What is the price of OPA337PA?
Current OPA337PA pricing is available through the Request a Quote form on this page. The exact commercial terms depend on order quantity, delivery requirements, and inventory at the time of quotation. The structured price evidence for the exact OPA337PA suffix is empty because no qualifying quantity-break table was available, so no price figure should be inferred from generic amplifier listings.
What is the lead time for OPA337PA?
Request the current OPA337PA lead time through the Request a Quote form on this page. Lead time can vary with order quantity, manufacturing availability, and fulfillment conditions, so it should be confirmed for the exact 8-PDIP ordering configuration. The manufacturer product page and distributor listing identify OPA337PA as a standard single-supply 3 MHz CMOS operational amplifier in an 8-PDIP package.
Is OPA337PA in stock?
Current OPA337PA stock status should be confirmed through the Request a Quote form on this page. Stock changes over time and may differ by package, quantity, and shipment destination. Because a dependable quantity-specific inventory statement is not attached to this product record, use the quote form to request the current availability of the exact OPA337PA 8-PDIP part.
What is opa337 ltspice?
An OPA337 LTspice representation is a simulation model used to evaluate the OPA337 amplifier family before hardware is built. The model should reproduce the selected device's supply limits, input behavior, output swing, gain-bandwidth response, and stability characteristics. Use the official Texas Instruments product page to locate the manufacturer's simulation resources or create a behavioral model from the datasheet characteristics when no packaged model is listed.

کے لیے انجینئرنگ ریفرنس ڈیٹا OPA337PA — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔

انتخاب کی گائیڈ

Choose OPA337PA for a new low-voltage, single-supply design that specifically requires the documented 5.5 V maximum supply, 3 MHz gain-bandwidth product, FET input, and rail-to-rail output in an 8-pin PDIP package. It is particularly suitable for high-impedance sensor interfaces, transimpedance stages, buffering, active filters, and through-hole prototypes. Consider OPA337UA when that same-family suffix better matches the required temperature grade, lifecycle plan, or sourcing position. Before substituting OPA337UA, compare its manufacturer datasheet against every electrical limit, pin function, package drawing, and stability condition used by the original design. Neither choice should be treated as interchangeable solely because both use a through-hole DIP package; verify the exact ordering suffix and application requirements. For designs where the 8-pin PDIP footprint is not required, a smaller surface-mount implementation may offer better board-area efficiency, although it would not be a mechanical drop-in replacement.

متبادلات کے ساتھ موازنہ

پیرامیٹر یہ پروڈکٹ OPA337UA
Brand Texas Instruments Texas Instruments
Package 8-PDIP PDIP-8 - through-hole

اہم امتیازی خصوصیات

  • Combines a 3 MHz gain-bandwidth product with a 5.5 V maximum supply (بمقابلہOPA337UA)
  • Uses a rail-to-rail output stage (بمقابلہOPA337UA)
  • FET-input architecture with 10 pA maximum input bias current (بمقابلہOPA337UA)

ڈیزائن نوٹس

Place the supply-decoupling capacitor close to the amplifier's supply and ground connections, and keep the return path short to reduce trace inductance. For high-impedance sensor inputs, minimize exposed PCB area around each input, avoid nearby switching nodes, and use a guarded ground where appropriate. The 8-pin PDIP layout provides generous spacing for through-hole construction, but analog input and output traces should still be routed away from digital switching paths.

Do not assume that a rail-to-rail output reaches the supply rail under every load. Check the manufacturer output-swing characteristics at the intended supply voltage and load current. Likewise, single-supply operation does not make every input voltage legal: verify the common-mode input range before applying signals near ground. Use stable feedback ratios and the manufacturer's guidance when driving capacitive loads or operating at high closed-loop gain.

For source impedances above a few kilohms, account for amplifier input bias current, PCB leakage, and input capacitance before choosing the closed-loop bandwidth. In a transimpedance stage, select the feedback resistor and compensation capacitor as a matched pair rather than treating them independently. Prototype with the intended source and load because parasitics can change phase margin even when the nominal resistor values appear correct.

تعمیل کی معلومات

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
لیڈ فری
Unknown
ہیلوجن فری
Unknown
کنفلیکٹ منرلز
Unknown

No explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals declarations were identified for OPA337PA. AEC-Q100 is not applicable to this general-purpose operational amplifier.

ڈیٹا کی تصدیق کی تاریخ: 2026-11-09 — ڈیٹا XAIPART کی کمپوننٹ انجینئرنگ ٹیم کے ذریعے تصدیق شدہ اور ترتیب شدہ

متعلقہ تلاشیں

opa337 ltspice OPA337PA datasheet OPA337PA datasheet pdf OPA337PA pinout OPA337PA specifications OPA337PA equivalent OPA337PA replacement OPA337PA vs OPA337UA OPA337PA 8-PDIP OPA337PA 3 MHz op amp Texas Instruments OPA337PA OPA337PA price

متعلقہ اجزاء اور اصطلاحات

Texas Instruments OPA337PA OPA337 OPA337UA MICROAMPLIFIER operational amplifier general-purpose amplifier analog amplifier amplifier IC semiconductor CMOS FET input rail-to-rail output single-supply operation gain-bandwidth product input bias current 8-PDIP through-hole package sensor conditioning transimpedance amplifier active low-pass filter signal buffering portable measurement equipment
فوری کوٹ RFQ
مکمل تفصیلات بھریں — ہماری سیلز ٹیم 24 گھنٹوں میں جواب دے گی
پارٹ نمبر مینوفیکچرر پیکج QTY ہدف قیمت کل رقم
✓
کوٹ جمع ہو گیا!

ہم 24 گھنٹوں کے اندر آپ کے ای میل کا جواب دیں گے

1
RFQ جمع ہو گیا
2
کوٹ موصول ہو گیا
3
آرڈر دے دیا گیا
4
ادائیگی
5
بھیج دیا گیا
6
ڈیلیور شدہ
RFQ تفصیلات دیکھیں