OPA690ID - 300MHz Wideband Op Amp | Texas Instruments
MPN: OPA690ID ✓ সক্রিয়OPA690ID সারাংশ
A wideband voltage-feedback operational amplifier is a semiconductor amplifier that uses voltage feedback to control gain and bandwidth. Unlike a current-feedback amplifier, it offers a familiar resistor-defined gain relationship and can operate at unity gain. The OPA690 belongs to the operational-amplifier hierarchy within analog signal-chain and power-management ICs, making it useful where signals must be amplified with high bandwidth, low distortion, and fast settling performance.
Key characteristics include 300 MHz small-signal bandwidth, 1800 V/us slew rate, unity-gain stability, and an output-current capability of 190 mA. Its output can swing to ±4.0 V under the cited conditions, while the disable pin supports power-control and signal-isolation schemes. The flexible supply range allows operation from a 12 V single rail or from ±5 V dual rails.
The OPA690 uses voltage-feedback architecture with an output stage designed for high current and low headroom requirements. This combination permits large-signal bandwidth and fast transient response without requiring a current-feedback amplifier. Unity-gain stability makes the device suitable for buffers, instrumentation paths, and gain stages where a conventional feedback network is preferred. Precise distortion, noise, settling-time, and input-offset values must be selected from the appropriate operating conditions in the manufacturer datasheet.
Typical applications include high-speed instrumentation, broadband signal conditioning, active filters, data-acquisition front ends, communications equipment, and test-and-measurement systems. The disable function is particularly useful when an amplifier stage must be disconnected or placed in a low-power state without removing the complete circuit from service.
When designing around the OPA690ID, maintain the required supply headroom for the selected output swing and keep feedback traces short to reduce parasitic feedback. Decoupling capacitors should be placed close to the supply pins, and the disable signal should be driven with clean logic levels that remain valid during startup and shutdown.
This product page combines the OPA690’s principal electrical characteristics, pin assignment, application guidance, and same-package alternative options with practical design guidance. It helps engineers distinguish confirmed device attributes from parameters that require direct verification against the Texas Instruments OPA690 datasheet.
এর জন্য ড্রপ-ইন বিকল্প OPA690ID — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।
OPA692ID
✅ ড্রপ-ইন📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
OPA690IDG4
✅ ড্রপ-ইন📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
OPA690ID সর্বোচ্চ রেটিং ও বৈদ্যুতিক বৈশিষ্ট্য
| Amplifier Type | Voltage Feedback Operational Amplifier |
| Number of Circuits | 1 circuit |
| Gain-Bandwidth Product | 300 MHz |
| Slew Rate | 1800 V/us |
| Unity-Gain Stable | Yes |
| Disable Function | Yes |
| Dual-Supply Operating Range | ±2.5 V to ±5 V |
| Single-Supply Operating Range | +2.5 V to +12 V |
| সর্বোচ্চ আউটপুট কারেন্ট | 190 mA |
| Output Voltage Swing | ±4.0 V |
| প্যাকেজ | 8-pin SOIC |
| মাউন্টিং টাইপ | Surface mount |
| Channel Count | 1 channel |
| Input Type | Voltage input |
| অপারেটিং তাপমাত্রা | -40 °C to +85 °C |
| RoHS স্ট্যাটাস | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | not_applicable |
OPA690ID পিন কনফিগারেশন
| পিন 1 | NC — Not connected |
| পিন 2 | -IN — Inverting input |
| পিন 3 | +IN — Non-inverting input |
| পিন 4 | V- — Negative supply connection |
| পিন 5 | DISABLE — Amplifier disable input |
| পিন 6 | OUT — Amplifier output |
| পিন 7 | V+ — Positive supply connection |
| পিন 8 | NC — Not connected |
সাধারণ ব্যবহার
OPA690ID এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: High-Speed Instrumentation Signal Conditioning, Data-Acquisition Front Ends, Communications Signal Conditioning, Active Filtering, Test and Measurement Equipment, Power-Controlled Analog Channels.
High-Speed Instrumentation Signal Conditioning
The OPA690ID fits instrumentation paths that require broad closed-loop bandwidth and rapid signal transitions. Its 300 MHz gain-bandwidth product supports unity-gain buffering and moderate feedback gains, while the 1800 V/us slew rate helps preserve large-amplitude waveform shape. The 190 mA output-current capability provides useful drive margin for sensor interfaces, test-probe drivers, and signal-conditioning networks. Unity-gain stability also allows conventional resistor-based feedback networks to be used without selecting a current-feedback amplifier. Keep supply-decoupling capacitors close to the device and route the feedback connection directly to the amplifier output to minimize parasitic loop effects.
সুপারিশকৃত
Data-Acquisition Front Ends
OPA690ID applications in data-acquisition systems benefit from the combination of 300 MHz bandwidth and fast output response. The device can buffer sensor outputs, level-shift signals within its supported supply range, and drive downstream conversion stages without requiring a high-speed current-feedback architecture. Its unity-gain stability supports direct buffer use, and its disable input allows a measurement channel to be isolated during calibration or instrument resets. The ±4.0 V output-swing capability must be checked against the acquisition system’s input range. Layout should include short ground returns, low-loop-area feedback traces, and local supply bypassing to preserve signal integrity at high bandwidth.
সুপারিশকৃত
Communications Signal Conditioning
The OPA690ID can condition wideband communications signals when the system requires high slew rate and a stable low-gain configuration. Its 1800 V/us slew rate reduces distortion on rapidly changing waveforms, while 300 MHz bandwidth provides substantial headroom for amplifier stages operating below the device’s upper frequency limit. A flexible operating range from ±2.5 V to ±5 V supports dual-rail analog circuitry, and single-supply operation is available for lower-complexity designs. The disable function can assist with channel gating or power-control schemes. Engineers should evaluate output swing, load current, stability, and permissible input common-mode range against the communications channel’s operating conditions.
সুপারিশকৃত
Active Filtering
OPA690ID is appropriate for active-filter stages requiring a wide open-loop bandwidth and high slew rate. A 300 MHz gain-bandwidth product leaves frequency-range margin above many signal-band filter sections, while 1800 V/us slew rate helps maintain low distortion through transitions within the passband. Unity-gain stability permits conventional voltage-feedback gain and component-selection methods. The 190 mA output-current capability can drive the next filter or measurement stage more effectively than a low-current general-purpose amplifier. Component tolerances, op-amp gain-bandwidth behavior, and output loading should be evaluated together. Place filter resistors and capacitors close to the relevant pins, and use a ground plane that does not interrupt the high-frequency return path.
সুপারিশকৃত
Test and Measurement Equipment
The OPA690ID supports wideband test and measurement systems where low-frequency precision amplifiers may lack sufficient slew rate or bandwidth. Its 300 MHz bandwidth and 1800 V/us slew rate make it suitable for driver, buffer, and signal-conditioning stages that handle fast transitions. The disable pin can simplify instrument state control by turning off an active path without removing the circuit from the chassis. The 190 mA output-current capability also allows the amplifier to drive moderate loading, subject to output-swing and stability checks. For bench instruments, use a compact low-inductance ground structure, place bypass capacitors at the supply pins, and verify settling behavior before interpreting time-domain measurements.
সুপারিশকৃত
Power-Controlled Analog Channels
The OPA690ID’s disable function makes it useful in analog channels that require controlled shutdown between operating intervals. For example, a test system, communications interface, or reusable measurement module can disable the amplifier while retaining local biasing and board connections. This approach can reduce unnecessary active-circuit activity without requiring a separate analog switch at the signal input. The wideband voltage-feedback architecture still provides 300 MHz gain-bandwidth product, 1800 V/us slew rate, and unity-gain stability for active operation. The disable logic must meet the manufacturer’s input thresholds, and supply bypass capacitors should be sized to handle turn-on transients without causing excessive supply disturbance.
সুপারিশকৃত
সুপারিশকৃত পণ্যের সারসংক্ষেপ
এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা OPA690ID — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।
নির্বাচন গাইড
বিকল্পের সাথে তুলনা
| পারামিটার | এই পণ্য | OPA692ID | OPA690IDG4 |
|---|---|---|---|
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
মূল পার্থক্যসমূহ
- Wideband performance in an 8-pin SOIC (বনামOPA692ID)
- High output-current capability (বনামOPA690IDG4)
- Flexible single- and dual-supply operation (বনামOPA692ID)
ডিজাইন নোট
Place the input, output, and feedback components close to the OPA690ID, and keep the feedback trace short enough to minimize parasitic coupling. Connect the bypass capacitor directly between each supply pin and the ground plane so high-frequency return current does not share a long trace with analog signals. For dual-supply operation, provide local bypass on both V+ and V- connections. The SOIC footprint has short leads, but incorrect resistor placement can still create a large feedback loop and reduce stability margin.
Verify that the selected single- or dual-supply voltage supports the required input range and output swing. The OPA690ID supports single-supply operation up to +12 V and dual-supply operation from ±2.5 V to ±5 V, with stated output swing to ±4.0 V. The disable input must also remain within its valid logic limits. Check the disable state and startup sequence so the control signal cannot create an undefined amplifier output during power transitions.
Use the unity-gain-stable voltage-feedback architecture with conventional feedback resistors, and confirm stability with the actual source impedance, load capacitance, and resistor values. High-speed signals magnify stray capacitance and probe loading, so use short interconnects and controlled test points. When driving downstream circuitry, confirm both output-current demand and capacitive loading against the OPA690 operating limits before finalizing the buffer or gain stage.
কমপ্লায়েন্স তথ্য
Compliance declarations were not confirmed for the exact OPA690ID ordering code. AEC-Q100 is not applicable because OPA690ID is an industrial catalog operational amplifier rather than an automotive-qualified variant.