NXP Semiconductors

PCA9509D - 400 kHz I2C Level Translator | NXP

MPN: PCA9509D ✓ সক্রিয়
8-pin SO package Package 400 kHz Speed
সর্বনিম্ন অর্ডার পরিমাণ: 1 |

PCA9509D সারাংশ

The NXP Semiconductors PCA9509D is a 400 kHz, two-channel I2C-bus and SMBus level-translating repeater housed in an 8-pin SO package. It allows a processor operating at a lower voltage to communicate with standard I2C-bus or SMBus input/output devices operating at a higher voltage. The device provides bidirectional signal translation while preserving the open-drain structure required by these two-wire buses.

An I2C level translator is an interface IC within the broader hierarchy of serial-interface devices, bus-interface controllers, interface circuits, and semiconductors. This category solves voltage-domain mismatches between processors and peripherals without requiring every connected device to operate from the same supply voltage. The PCA9509 is particularly useful when the processor-side logic voltage and the peripheral-side bus voltage differ but both devices use open-drain signaling.

The PCA9509D supports operation up to 400 kHz and provides two translated channels. Its two-channel arrangement allows one SDA and one SCL signal to cross between voltage domains. The translated arrangement preserves standard bus behavior, including wired-AND signaling through open-drain outputs and the need for appropriate pull-up resistors on each voltage domain.

According to the NXP product information, the PCA9509 is intended to bridge a processor's low-voltage two-wire serial bus to conventional I2C-bus or SMBus I/O. The eight-pin surface-mount package supports compact interface isolation on industrial and embedded boards. Because the translator operates bidirectionally, both sides can initiate or acknowledge transactions without separate directional buffers.

Typical uses include low-voltage microcontrollers interfacing with higher-voltage sensors, EEPROMs, real-time clocks, analog converters, and bus-management devices. It can also extend a processor-based control system to a legacy SMBus peripheral, provided the voltage domains, pull-up networks, capacitance, and bus speed remain within the device's operating limits.

PCB design should treat each voltage domain as a separate pull-up network. Confirm the supply levels, pull-up values, bus capacitance, and maximum clock rate before implementation. The 400 kHz rating makes bus timing and rise-time verification especially important when cable length or slow pull-up resistors are present.

This page organizes the PCA9509D interface function, package characteristics, candidate drop-in alternatives, application guidance, and design considerations for faster component selection and PCB planning.

এর জন্য ড্রপ-ইন বিকল্প PCA9509D — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।

এই সিরিজের ভ্যারিয়েন্ট

একই সিরিজের মডেল যেগুলো drop-in compatible PCA9509D (একই form factor এবং footprint) — পার্থক্য রয়েছে Package.

NXP Semiconductors
Package: 8-TSSOP (SOT505-1)
এর সাথে তুলনা করুন PCA9509D →

PCA9509A

✅ ড্রপ-ইন ⚠️ স্পেক যাচাইকৃত নয়
📦 SO-8
Same SO-8 family footprint, but includes the port-A internal current source; pull-up and power behavior must be checked.

📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)

PCA9509DP,118

✅ ড্রপ-ইন ⚠️ স্পেক যাচাইকৃত নয়
NXP Semiconductors
📦 SO-8
Level translating I2C-bus/SMBus repeater (buffer, redriver) · 2 (SDA and SCL bidirectional) · 2-Wire Bus (I2C) · 2-Wire Bus (I2C/SMBus) · 400 kHz (I2C fast mode) · 3 V to 5.5 V · 5 mA · 109 ns

মূল্যের জন্য যোগাযোগ করুন

ডেটাশিট দেখুন →

PCA9509PDP

✅ ড্রপ-ইন
📦 SO-8
Same SO-8 footprint and PCA9509 family, but the P-version changes the internal current-source configuration.

📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)

PCA9509D বিশেষণ

Device Type I2C-bus/SMBus level-translating repeater
Number of Translated Channels 2 channels
Maximum Bus Frequency 400 kHz
Supported Serial Buses I2C-bus and SMBus
Signal Direction Bidirectional
Logic Interface Open-drain two-wire serial bus
প্যাকেজ 8-pin SO package
মাউন্টিং টাইপ Surface mount
পিন সংখ্যা 8 pins
Temperature Grade Industrial

PCA9509D 8-pin so package পিন কনফিগারেশন গাইড

PCA9509D (8-pin so package প্যাকেজ)-এর পিন কনফিগারেশন। পিন নম্বরিং, ফাংশন এবং সংযোগ ডায়াগ্রাম প্রস্তুতকারকের ডেটাশিটে সংজ্ঞায়িত করা আছে। সঠিক ফুটপ্রিন্ট এবং সোল্ডারিং নির্দেশিকার জন্য এটি দেখুন।

PCA9509D-এর জন্য 8-pin so package প্যাকেজ পিনআউট ডায়াগ্রাম

এর জন্য বিস্তারিত পিনআউট ডেটা পাওয়া যায়নি PCA9509D.

দেখুন ডেটাশিট সম্পূর্ণ পিন কনফিগারেশনের জন্য।

সাধারণ ব্যবহার

PCA9509D এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Low-Voltage MCU to Higher-Voltage Sensor Interface, Processor-to-EEPROM Bus Bridging, SMBus Management Peripheral Interfacing, Real-Time Clock Bridge, Analog Converter and Data-Acquisition Interface, Mixed-Voltage Embedded Control Board.

🧩

Low-Voltage MCU to Higher-Voltage Sensor Interface

The PCA9509D fits designs in which a low-voltage microcontroller communicates with an I2C sensor operating from a higher supply. Its two bidirectional channels translate the SCL and SDA signals between the processor and sensor voltage domains. The 400 kHz bus rating supports standard-speed sensor traffic, while the open-drain implementation preserves normal I2C wired-AND behavior. Place separate pull-ups on both sides and select resistor values from the combined bus capacitance and required rise time. Confirm the MCU, sensor, and translator supply limits against the NXP datasheet before layout release.

💾

Processor-to-EEPROM Bus Bridging

The PCA9509D can connect a low-voltage embedded processor to an I2C EEPROM whose interface operates in a higher voltage domain. The level translator preserves bidirectional acknowledgments, allowing the processor to address, write, and read the memory device without changing the EEPROM bus level. Its two channels cover SDA and SCL, and the 400 kHz maximum rate is suitable for many standard EEPROM access patterns. The design still requires independent pull-up networks in both voltage domains. Check rise time at the longest supported bus rate and verify that no device pulls either side below its specified voltage range.

🔧

SMBus Management Peripheral Interfacing

The PCA9509D is appropriate for an SMBus controller that must communicate with management devices operating at a different logic voltage. It supports both I2C-bus and SMBus and translates the two bidirectional signals without changing their open-drain behavior. This makes it suitable for clock, sensor-hub, and power-management paths where the host processor voltage differs from the peripheral voltage. The 400 kHz capability accommodates common SMBus operating rates, although system timing must also satisfy each connected device. Use separate pull-ups, maintain compatible ground references, and confirm address and electrical limits for every bus participant.

⏱️

Real-Time Clock Bridge

The PCA9509D can isolate a low-voltage processor from a higher-voltage real-time clock connected through an I2C interface. Bidirectional translation preserves clock reads, writes, and acknowledgments across the voltage boundary. With two translated channels, the same device handles both clock and data lines. The 400 kHz operating limit is normally more than sufficient for RTC transactions, but total bus capacitance and pull-up resistance still determine communication reliability. Keep the translator close to the voltage-domain interface when trace length or capacitive loading is significant, and use the manufacturer application guidance to choose compliant pull-up values.

📊

Analog Converter and Data-Acquisition Interface

The PCA9509D supports low-voltage digital control interfaces to analog converters, data-acquisition devices, or mixed-signal peripherals operating at a higher voltage. It translates the SCL and SDA control bus while allowing the converter to return status or measurement-related data through the same lines. The bidirectional structure avoids separate transmit and receive paths, and the 400 kHz rate supports command and configuration traffic. Use short traces, validate capacitive loading, and calculate pull-up rise times before operation. The translator does not isolate ground or protect the bus from excessive voltage, so supply sequencing and voltage-limit checks remain essential.

🏭

Mixed-Voltage Embedded Control Board

The PCA9509D is useful on embedded control boards that combine a modern low-voltage processor with legacy higher-voltage bus peripherals. It provides a defined voltage boundary for SCL and SDA without requiring the processor to operate at the peripheral voltage. The 8-pin SO package simplifies assembly in designs that already use SO components, while the 400 kHz rate supports ordinary control traffic. Place independent pull-ups close to the corresponding voltage domains, provide a common ground, and avoid placing the translator where long stubs increase capacitance. Validate the complete bus with the slowest connected device and the worst-case pull-up network.

সুপারিশকৃত পণ্যের সারসংক্ষেপ

PCA9509DP Same-family TSSOP level translator for compact designs ব্যবহৃত হয়: Low-Voltage MCU to Higher-Voltage Sensor Interface, Processor-to-EEPROM Bus Bridging, Real-Time Clock Bridge, Mixed-Voltage Embedded Control Board PCA9509PDP Related NXP level-translating repeater configuration ব্যবহৃত হয়: Low-Voltage MCU to Higher-Voltage Sensor Interface, Processor-to-EEPROM Bus Bridging, Real-Time Clock Bridge, Mixed-Voltage Embedded Control Board PCA9509A Same-family NXP level translator with a different current-source configuration ব্যবহৃত হয়: SMBus Management Peripheral Interfacing, Analog Converter and Data-Acquisition Interface PCA9509 Related PCA9509-family bus translator ব্যবহৃত হয়: SMBus Management Peripheral Interfacing, Analog Converter and Data-Acquisition Interface
What is the PCA9509D used for?
The PCA9509D is a two-channel, bidirectional I2C-bus and SMBus level-translating repeater for connecting low-voltage processor logic to higher-voltage bus devices. According to the NXP product information, it lets a low-voltage two-wire serial bus interface with conventional I2C-bus or SMBus I/O while preserving open-drain operation.
What is the maximum bus frequency of the PCA9509D?
The PCA9509D supports I2C-bus and SMBus operation up to 400 kHz. This figure comes from the NXP product listing for the device. The actual operating rate also depends on pull-up resistance, total bus capacitance, wiring length, and the timing characteristics of the connected processor and peripheral.
Is PCA9509D bidirectional?
Yes, the PCA9509D is bidirectional on both translated channels. The NXP product information identifies it as a level-translating repeater for two-wire serial buses. Each side can therefore transmit and receive data, allowing the processor and peripheral to initiate transactions and return acknowledgments normally.
What package does the PCA9509D use?
The PCA9509D is offered in an 8-pin SO surface-mount package. Product listings describe the PCA9509D,118 ordering form as an 8-SO device, while the related PCA9509DP,118 ordering form uses an 8-TSSOP package. Confirm the package suffix before placing a footprint on the PCB.
Where can I download the PCA9509D datasheet PDF?
The official PCA9509D datasheet and product resources are available through the NXP part page at https://www.nxp.com/part/PCA9509D. Use the manufacturer datasheet for the complete pin description, recommended operating conditions, voltage limits, timing characteristics, and application diagram before finalizing the circuit.
Where can I find the PCA9509D pinout?
The PCA9509D pin assignment is defined by the manufacturer datasheet linked from the NXP product page. The device has eight pins in its SO package. Use the datasheet pin-description table when assigning SCL, SDA, supply, and ground connections, and verify the exposed-pad requirement for the selected ordering code.
Do I need separate pull-up resistors on both sides of the PCA9509D?
Yes, each voltage domain should have its own correctly valued pull-up network. The NXP application concept for the PCA9509 uses open-drain I2C or SMBus signaling, so SCL and SDA require pull-ups in the low-voltage and high-voltage domains. The exact resistor values must be selected from the bus capacitance and rise-time requirements.
Can the PCA9509D connect an MCU to a higher-voltage sensor?
Yes, the PCA9509D is suitable when the MCU operates at a lower logic voltage and the sensor uses a higher I2C voltage domain. The translator provides bidirectional level translation for SCL and SDA. Confirm the sensor's input limits, bus capacitance, pull-up values, and the PCA9509D supply limits before connecting it.
What is the difference between PCA9509D and PCA9509DP?
The principal ordering difference is the physical package: PCA9509D is the 8-pin SO form, while PCA9509DP is the 8-pin TSSOP form. Their board footprints are therefore not interchangeable. Both belong to the PCA9509 level-translating repeater family, but the PCA9509DP device should not be selected as a drop-in replacement for an existing SO-8 PCB footprint.
Is PCA9509A the same as PCA9509D?
The PCA9509A belongs to the same PCA9509 level-translating family and uses a compatible SO-8 format, but its internal port-A current-source configuration differs. The NXP family information indicates that PCA9509P omits the port-A internal current source found in PCA9509A. Confirm the specific datasheet, pull-up requirements, and supply levels before approving a substitution.
What can replace PCA9509D in an existing design?
The closest same-family replacements are the NXP PCA9509A, PCA9509, and PCA9509PDP, subject to package and internal-feature verification. The PCA9509DP is not a direct drop-in option because it uses TSSOP rather than SO packaging. Use the Request a Quote form on this page to ask about availability and sourcing support.
When should I choose PCA9509D instead of a PCA9509 variant?
Choose the PCA9509D when an existing design requires the 8-pin SO footprint and the standard PCA9509 level-translating repeater configuration. Consider PCA9509A only after checking its port-A current source, because that feature changes pull-up and power behavior. PCA9509PDP may be suitable functionally, but verify its ordering code and exact package marking.
Is PCA9509D suitable for SMBus systems?
Yes, the PCA9509D supports both I2C-bus and SMBus interfaces. According to the NXP product information, it is a level-translating repeater designed to connect a processor's low-voltage two-wire serial bus with standard I2C-bus or SMBus I/O. Its 400 kHz capability suits standard-speed bus communication.
Where can I buy PCA9509D and what is its lead time?
Use the Request a Quote form on this page to request PCA9509D pricing, current stock, minimum order quantity, and lead time. The form provides a direct purchasing channel without relying on an outdated catalog price. Confirm the exact ordering suffix and required package when submitting the request.
What are the key specifications of PCA9509D that engineers should know?
The key PCA9509D specifications are two bidirectional translated channels, a 400 kHz maximum bus rate, support for I2C-bus and SMBus signaling, and an 8-pin SO package. The device also provides an industrial temperature grade according to its component listing. Detailed voltage, current, and timing limits require confirmation from the manufacturer datasheet.

এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা PCA9509D — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।

নির্বাচন গাইড

Choose PCA9509D when the PCB footprint is an 8-pin SO layout and the design requires bidirectional, two-channel level translation between low-voltage I2C or SMBus logic and a higher-voltage bus domain. Its stated 400 kHz capability suits standard-speed embedded, sensor, EEPROM, real-time-clock, and management-bus interfaces. Consider PCA9509A only after accounting for its internal port-A current source, which changes pull-up and power behavior. PCA9509PDP may fit an SO-8 design when its current-source configuration is acceptable, but the exact ordering code must be verified. PCA9509DP is not a drop-in replacement because it uses TSSOP packaging. For every candidate, verify supply limits, pin voltages, pull-up networks, bus capacitance, and timing before approving a substitution.

বিকল্পের সাথে তুলনা

পারামিটার এই পণ্য PCA9509A PCA9509 PCA9509PDP
Brand NXP Semiconductors NXP Semiconductors NXP Semiconductors NXP Semiconductors
Package SO-8 SO-8 SO-8 SO-8
Device Type Level-translating repeater Level-translating repeater Level-translating repeater Level-translating repeater
Translated Channels 2 channels 2 channels 2 channels 2 channels
Supported Serial Buses I2C-bus and SMBus I2C-bus and SMBus I2C-bus and SMBus I2C-bus and SMBus
Signal Direction Bidirectional Bidirectional Bidirectional Bidirectional

মূল পার্থক্যসমূহ

  • Provides a defined two-domain interface for I2C-bus and SMBus (বনামPCA9509DP)
  • Supports standard 400 kHz bus operation (বনামPCA9509A)
  • Avoids the port-A current-source variation found in another family member (বনামPCA9509A)

ডিজাইন নোট

Provide separate SDA and SCL pull-up networks for the low-voltage and high-voltage sides. The pull-up voltage on each side must match that side's bus domain, and neither network should unintentionally forward current into the opposite domain. Keep the translator and its local pull-ups close together when trace capacitance is significant, while observing the manufacturer's recommended layout in the datasheet.

Validate the bus rise time at the 400 kHz maximum rate using the actual pull-up resistance, total bus capacitance, and longest trace configuration. Excessively weak pull-ups can cause slow rising edges and missed transitions; overly strong pull-ups increase the current required from the open-drain devices. Include the translator and connected peripheral input capacitances when selecting resistor values.

Do not treat PCA9509D as galvanic isolation. The two voltage domains must share an appropriate ground reference, and the device does not provide protection from voltage applied outside its specified limits. Confirm the low-side and high-side supply ranges, pin voltages, power-up sequence, and whether the selected family member includes an internal port-A current source before substituting a related part.

Route SCL and SDA away from noisy switching nodes and maintain a compact path between the translator and the relevant pull-ups. Avoid long stubs to unused devices, because their input capacitance increases loading on the open-drain bus. When the two voltage domains cross a board boundary, place the translator near the interface and keep ground-return paths short and continuous.

কমপ্লায়েন্স তথ্য

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
লিড ফ্রি
Unknown
হ্যালোজেন ফ্রি
Unknown
কনফ্লিক্ট মিনারেলস
Unknown

The PCA9509D is an industrial-grade interface IC, not an automotive-qualified power device. Specific environmental and material compliance declarations require confirmation from NXP.

ডেটা যাচাই করা হয়েছে: 2026-11-19 — ডেটা XAIPART-এর কম্পোনেন্ট ইঞ্জিনিয়ারিং টিম দ্বারা যাচাই ও কিউরেট করা হয়েছে

সম্পর্কিত অনুসন্ধান

PCA9509D datasheet PCA9509D pinout PCA9509D datasheet pdf PCA9509D equivalent PCA9509D replacement PCA9509D cross reference PCA9509D vs PCA9509DP PCA9509D price PCA9509D stock NXP PCA9509D PCA9509D 400 kHz I2C translator PCA9509D SO-8 footprint PCA9509D SMBus application circuit what can replace PCA9509D is PCA9509D the same as PCA9509A

সম্পর্কিত কম্পোনেন্ট ও শর্তাবলী

NXP Semiconductors PCA9509D PCA9509A PCA9509 PCA9509DP PCA9509PDP I2C-bus SMBus level translator level-translating repeater bidirectional repeater open-drain bus interface IC bus-interface controller serial interface semiconductor SO-8 TSSOP-8 surface mount SMD pull-up resistor bus capacitance 400 kHz bus rate industrial temperature grade embedded control
তাৎক্ষণিক বিলওয়াছে রেকোজিউইট
সম্পূর্ণ বিবরণ পূরণ করুন — আমাদের সেলস টিম 24 ঘণ্টার মধ্যে উত্তর দেবে
পার্ট নম্বর উৎপাদক প্যাকেজ QTY লক্ষ্যমূল্য প্রসারিত
✓
বিল প্রস্তুত করা হয়েছে!

আমরা ২৪ ঘণ্টার মধ্যে আপনার ইমেইলে প্রত্যুত্তর দেব

1
RFQ জমা হয়েছে
2
কোটেশন পাওয়া গেছে
3
অর্ডার দেওয়া হয়েছে
4
পেমেন্ট
5
শিপ করা হয়েছে
6
ডেলিভারি হয়েছে
RFQ বিবরণ দেখুন