PCA9509D - 400 kHz I2C Level Translator | NXP
MPN: PCA9509D ✓ AktifPCA9509D Ringkasan
An I2C level translator is an interface IC within the broader hierarchy of serial-interface devices, bus-interface controllers, interface circuits, and semiconductors. This category solves voltage-domain mismatches between processors and peripherals without requiring every connected device to operate from the same supply voltage. The PCA9509 is particularly useful when the processor-side logic voltage and the peripheral-side bus voltage differ but both devices use open-drain signaling.
The PCA9509D supports operation up to 400 kHz and provides two translated channels. Its two-channel arrangement allows one SDA and one SCL signal to cross between voltage domains. The translated arrangement preserves standard bus behavior, including wired-AND signaling through open-drain outputs and the need for appropriate pull-up resistors on each voltage domain.
According to the NXP product information, the PCA9509 is intended to bridge a processor's low-voltage two-wire serial bus to conventional I2C-bus or SMBus I/O. The eight-pin surface-mount package supports compact interface isolation on industrial and embedded boards. Because the translator operates bidirectionally, both sides can initiate or acknowledge transactions without separate directional buffers.
Typical uses include low-voltage microcontrollers interfacing with higher-voltage sensors, EEPROMs, real-time clocks, analog converters, and bus-management devices. It can also extend a processor-based control system to a legacy SMBus peripheral, provided the voltage domains, pull-up networks, capacitance, and bus speed remain within the device's operating limits.
PCB design should treat each voltage domain as a separate pull-up network. Confirm the supply levels, pull-up values, bus capacitance, and maximum clock rate before implementation. The 400 kHz rating makes bus timing and rise-time verification especially important when cable length or slow pull-up resistors are present.
This page organizes the PCA9509D interface function, package characteristics, candidate drop-in alternatives, application guidance, and design considerations for faster component selection and PCB planning.
Alternatif penggantian untuk PCA9509D — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian PCA9509D (sama faktor bentuk dan footprint) — berbeda di dalam Package.
PCA9509A
✅ Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif referensi (tidak dalam katalog)
PCA9509DP,118
✅ Drop-In ⚠️ Spesifikasi Tidak DisahkanKontak untuk harga
Lihat Datasheet →PCA9509PDP
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
PCA9509D Spesifikasi
| Device Type | I2C-bus/SMBus level-translating repeater |
| Number of Translated Channels | 2 channels |
| Maximum Bus Frequency | 400 kHz |
| Supported Serial Buses | I2C-bus and SMBus |
| Signal Direction | Bidirectional |
| Logic Interface | Open-drain two-wire serial bus |
| Paket | 8-pin SO package |
| Tipe Mounting | Surface mount |
| Jumlah Pin | 8 pins |
| Temperature Grade | Industrial |
PCA9509D 8-pin so package Diamant Konfigurasi Panduan
Konfigurasi pin untuk PCA9509D (8-pin so package pakai pakai). Penomoran pin, fungsi, dan diagram koneksi ditetapkan dalam datasheet produsen. Lihatnya untuk footprint dan pedoman perpindahan paruh.
Tidak ada data diatribut pin yang tersedia untuk PCA9509D.
Lihat ke: datasheet produk untuk konfigurasi pin penuh.
Aplikasi Umum
PCA9509D cocok untuk 6 aplikasis: Low-Voltage MCU to Higher-Voltage Sensor Interface, Processor-to-EEPROM Bus Bridging, SMBus Management Peripheral Interfacing, Real-Time Clock Bridge, Analog Converter and Data-Acquisition Interface, Mixed-Voltage Embedded Control Board.
Low-Voltage MCU to Higher-Voltage Sensor Interface
The PCA9509D fits designs in which a low-voltage microcontroller communicates with an I2C sensor operating from a higher supply. Its two bidirectional channels translate the SCL and SDA signals between the processor and sensor voltage domains. The 400 kHz bus rating supports standard-speed sensor traffic, while the open-drain implementation preserves normal I2C wired-AND behavior. Place separate pull-ups on both sides and select resistor values from the combined bus capacitance and required rise time. Confirm the MCU, sensor, and translator supply limits against the NXP datasheet before layout release.
Direkomendasikan
Processor-to-EEPROM Bus Bridging
The PCA9509D can connect a low-voltage embedded processor to an I2C EEPROM whose interface operates in a higher voltage domain. The level translator preserves bidirectional acknowledgments, allowing the processor to address, write, and read the memory device without changing the EEPROM bus level. Its two channels cover SDA and SCL, and the 400 kHz maximum rate is suitable for many standard EEPROM access patterns. The design still requires independent pull-up networks in both voltage domains. Check rise time at the longest supported bus rate and verify that no device pulls either side below its specified voltage range.
Direkomendasikan
SMBus Management Peripheral Interfacing
The PCA9509D is appropriate for an SMBus controller that must communicate with management devices operating at a different logic voltage. It supports both I2C-bus and SMBus and translates the two bidirectional signals without changing their open-drain behavior. This makes it suitable for clock, sensor-hub, and power-management paths where the host processor voltage differs from the peripheral voltage. The 400 kHz capability accommodates common SMBus operating rates, although system timing must also satisfy each connected device. Use separate pull-ups, maintain compatible ground references, and confirm address and electrical limits for every bus participant.
Direkomendasikan
Real-Time Clock Bridge
The PCA9509D can isolate a low-voltage processor from a higher-voltage real-time clock connected through an I2C interface. Bidirectional translation preserves clock reads, writes, and acknowledgments across the voltage boundary. With two translated channels, the same device handles both clock and data lines. The 400 kHz operating limit is normally more than sufficient for RTC transactions, but total bus capacitance and pull-up resistance still determine communication reliability. Keep the translator close to the voltage-domain interface when trace length or capacitive loading is significant, and use the manufacturer application guidance to choose compliant pull-up values.
Direkomendasikan
Analog Converter and Data-Acquisition Interface
The PCA9509D supports low-voltage digital control interfaces to analog converters, data-acquisition devices, or mixed-signal peripherals operating at a higher voltage. It translates the SCL and SDA control bus while allowing the converter to return status or measurement-related data through the same lines. The bidirectional structure avoids separate transmit and receive paths, and the 400 kHz rate supports command and configuration traffic. Use short traces, validate capacitive loading, and calculate pull-up rise times before operation. The translator does not isolate ground or protect the bus from excessive voltage, so supply sequencing and voltage-limit checks remain essential.
Direkomendasikan
Mixed-Voltage Embedded Control Board
The PCA9509D is useful on embedded control boards that combine a modern low-voltage processor with legacy higher-voltage bus peripherals. It provides a defined voltage boundary for SCL and SDA without requiring the processor to operate at the peripheral voltage. The 8-pin SO package simplifies assembly in designs that already use SO components, while the 400 kHz rate supports ordinary control traffic. Place independent pull-ups close to the corresponding voltage domains, provide a common ground, and avoid placing the translator where long stubs increase capacitance. Validate the complete bus with the slowest connected device and the worst-case pull-up network.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk PCA9509D — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | PCA9509A | PCA9509 | PCA9509PDP |
|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | SO-8 | SO-8 | SO-8 | SO-8 |
| Device Type | Level-translating repeater | Level-translating repeater | Level-translating repeater | Level-translating repeater |
| Translated Channels | 2 channels | 2 channels | 2 channels | 2 channels |
| Supported Serial Buses | I2C-bus and SMBus | I2C-bus and SMBus | I2C-bus and SMBus | I2C-bus and SMBus |
| Signal Direction | Bidirectional | Bidirectional | Bidirectional | Bidirectional |
Diferensiator Kunci
- Provides a defined two-domain interface for I2C-bus and SMBus (vsPCA9509DP)
- Supports standard 400 kHz bus operation (vsPCA9509A)
- Avoids the port-A current-source variation found in another family member (vsPCA9509A)
Catatan Desain
Provide separate SDA and SCL pull-up networks for the low-voltage and high-voltage sides. The pull-up voltage on each side must match that side's bus domain, and neither network should unintentionally forward current into the opposite domain. Keep the translator and its local pull-ups close together when trace capacitance is significant, while observing the manufacturer's recommended layout in the datasheet.
Validate the bus rise time at the 400 kHz maximum rate using the actual pull-up resistance, total bus capacitance, and longest trace configuration. Excessively weak pull-ups can cause slow rising edges and missed transitions; overly strong pull-ups increase the current required from the open-drain devices. Include the translator and connected peripheral input capacitances when selecting resistor values.
Do not treat PCA9509D as galvanic isolation. The two voltage domains must share an appropriate ground reference, and the device does not provide protection from voltage applied outside its specified limits. Confirm the low-side and high-side supply ranges, pin voltages, power-up sequence, and whether the selected family member includes an internal port-A current source before substituting a related part.
Route SCL and SDA away from noisy switching nodes and maintain a compact path between the translator and the relevant pull-ups. Avoid long stubs to unused devices, because their input capacitance increases loading on the open-drain bus. When the two voltage domains cross a board boundary, place the translator near the interface and keep ground-return paths short and continuous.
Informasi Konformitas
The PCA9509D is an industrial-grade interface IC, not an automotive-qualified power device. Specific environmental and material compliance declarations require confirmation from NXP.