Texas Instruments

PCA9515APWT - 2-Channel I2C Buffer, 400kHz | Texas Instruments

MPN: PCA9515APWT ✓ সক্রিয়
2.3 V to 3.6 V VCC Vdss 8-pin TSSOP (PW) Package 400 kHz Speed
সর্বনিম্ন অর্ডার পরিমাণ: 1 |

PCA9515APWT সারাংশ

The Texas Instruments PCA9515APWT is a 2-bit dual bidirectional I2C bus and SMBus repeater designed for extending and conditioning low-speed serial buses. It operates from a 2.3 V to 3.6 V VCC supply and supports operation up to 400 kHz, with two independent bidirectional buffer channels, an active-high repeater-enable input, 5.5 V tolerant I2C I/O, and open-drain I2C interfaces. The device is packaged in an 8-pin TSSOP (PW) package, designated by the PWT ordering suffix and intended for surface-mount assembly.

An I2C buffer or repeater is an interface IC that regenerates and electrically isolates a bidirectional bus segment. I2C and SMBus use open-drain signaling, so a buffer can reduce loading, restore signal rise time, isolate capacitive loading, and extend usable bus distance without changing the logical bus protocol. The PCA9515A belongs to the broader signal-buffer and repeater category within interface ICs, supporting embedded systems where a controller, sensor, EEPROM, or other peripheral sits behind a long or heavily loaded interconnect.

The main features of the PCA9515APWT include two identical bidirectional buffer channels, 2.3 V to 3.6 V operation, 400 kHz bus speed, 5.5 V tolerant I2C I/O, and mixed-mode signal support. The active-high repeater-enable input allows the device to be placed into a controlled operating state in designs that require bus segmentation or repeatable startup behavior. Open-drain I/O preserves the wired-AND nature of I2C while allowing the repeater to participate in normal clock and data signaling.

The device contains two identical bidirectional open-drain buffer circuits intended for I2C and SMBus systems. Its BiCMOS implementation combines CMOS logic with bipolar output characteristics, supporting mixed-mode signal operation while maintaining compatibility with the electrical conventions used by I2C-compatible peripherals. The buffered channels are intended to improve signal integrity when capacitance, wiring distance, or multiple bus branches create excessive loading on a host bus segment.

Typical applications include extending an I2C bus between a microcontroller and remote sensors, isolating a high-capacitance section of a bus, separating power domains with compatible logic levels, and preserving signal quality in industrial, embedded, and consumer electronics. The PCA9515APWT is most appropriate when the system uses a 400 kHz or lower I2C-compatible bus and requires two bidirectional repeater channels rather than a unidirectional level translator.

Designers should check the device enable state, supply decoupling, pull-up resistor placement, and the voltage tolerance of every connected I2C peripheral before deployment. Pull-ups must be placed on the correct bus segment and sized for its voltage, capacitance, sink current, and speed. The TSSOP footprint also requires adequate copper area and thermal planning even though the device is intended for low-power bus management.

This product page combines the manufacturer specification, package information, sourcing links, interface guidance, and practical bus-conditioning considerations. It is intended to help engineers identify whether the PCA9515APWT matches the required channel count, supply range, bus speed, and TSSOP footprint before placing it into an I2C or SMBus design.

এর জন্য ড্রপ-ইন বিকল্প PCA9515APWT — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।

এই সিরিজের ভ্যারিয়েন্ট

একই সিরিজের মডেল যেগুলো drop-in compatible PCA9515APWT (একই form factor এবং footprint).

PCA9515APWR

✅ ড্রপ-ইন
Texas Instruments
📦 8-pin TSSOP (PW)
Dual bidirectional I2C bus and SMBus repeater · 2 channels · 2.3 V to 3.6 V · 400 kHz · I2C and SMBus · Bidirectional open-drain buffer · Active-high EN with internal pullup · 5.5 V tolerant

মূল্যের জন্য যোগাযোগ করুন

ডেটাশিট দেখুন →

PCA9515APWT বিশেষণ

Product Type Dual bidirectional I2C bus and SMBus repeater
Number of Buffer Channels 2 channels
Supply Voltage Range 2.3 V to 3.6 V VCC
Maximum I2C Bus Frequency 400 kHz
I2C I/O Voltage Tolerance 5.5 V tolerant
Enable Input Voltage Tolerance 5.5 V tolerant
I2C Interface Type Open-drain
Signal Direction Bidirectional
Repeater Enable Active-high
Supported Protocol I2C and SMBus
Mixed-Mode Operation Supported
Process Technology BiCMOS
প্যাকেজ 8-pin TSSOP (PW)
Package Dimensions 0.173 inch, 4.40 mm width
মাউন্টিং টাইপ Surface mount
Ordering Suffix PWT

PCA9515APWT 0.173 inch, 4.40 mm width পিন কনফিগারেশন গাইড

PCA9515APWT (0.173 inch, 4.40 mm width প্যাকেজ)-এর পিন কনফিগারেশন। পিন নম্বরিং, ফাংশন এবং সংযোগ ডায়াগ্রাম প্রস্তুতকারকের ডেটাশিটে সংজ্ঞায়িত করা আছে। সঠিক ফুটপ্রিন্ট এবং সোল্ডারিং নির্দেশিকার জন্য এটি দেখুন।

PCA9515APWT-এর জন্য 0.173 inch, 4.40 mm width প্যাকেজ পিনআউট ডায়াগ্রাম

এর জন্য বিস্তারিত পিনআউট ডেটা পাওয়া যায়নি PCA9515APWT.

দেখুন ডেটাশিট সম্পূর্ণ পিন কনফিগারেশনের জন্য।

সাধারণ ব্যবহার

PCA9515APWT এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: I2C Bus Extension, Sensor Hub Isolation, Embedded EEPROM Access, Industrial Control Module, Portable Device Expansion, Communications Equipment.

🌐

I2C Bus Extension

The PCA9515APWT fits bus-extension designs where a microcontroller must communicate with a remote sensor, memory device, or transceiver across a longer PCB interconnect or cable segment. Its two bidirectional channels can regenerate clock and data signals, while the 400 kHz maximum operating rate matches standard Fast-mode I2C systems. The 2.3 V to 3.6 V supply range supports common 2.5 V and 3.3 V logic environments. The main design consideration is pull-up placement: each isolated bus segment requires correctly sized pull-ups, and excessive capacitance or resistance can still prevent reliable operation at the selected clock rate.

🧩

Sensor Hub Isolation

The PCA9515APWT is useful in sensor-hub designs where several temperature, light, motion, or environmental sensors create additional bus capacitance behind a host controller. The two bidirectional repeater channels can isolate those loads and restore signal levels without changing the I2C protocol. Its 400 kHz rating is appropriate for Fast-mode sensor polling, while 5.5 V tolerant I/O helps accommodate mixed-voltage peripherals when the bus pull-up voltage remains compatible. Keep the repeater close to the host-side bus, place the load-side pull-ups near the remote devices, and avoid combining long stubs with high capacitance without signal-integrity analysis.

🖥️

Embedded EEPROM Access

The PCA9515APWT can separate a microcontroller from an EEPROM or other configuration memory when PCB capacitance or connector loading makes the direct bus unreliable. Bidirectional operation is essential because I2C uses the same SDA and SCL conductors for control and returned data. The device's two channels allow SCL and SDA to be buffered independently, and its open-drain implementation remains compatible with standard I2C pull-up networks. For reliable operation, calculate pull-up resistance from bus capacitance and sink-current limits, confirm that the EEPROM supports the selected operating frequency, and provide a continuous ground reference across the separated segment.

🏭

Industrial Control Module

The PCA9515APWT is applicable in industrial control modules that connect a controller to remote sensors, actuators, or operator-interface devices over an I2C-compatible link. Its 2.3 V to 3.6 V operating supply and 400 kHz speed align with embedded 3.3 V control systems, while the repeater channels improve isolation from long wiring and connector capacitance. Industrial installations also require attention to grounding, surge exposure, pull-up fault conditions, and the enable pin behavior during reset. The TSSOP package supports compact controller boards, provided the layout preserves short return paths and avoids routing sensitive bus traces beside high-current switching nodes.

📱

Portable Device Expansion

The PCA9515APWT can condition an I2C link in a portable device when a display, touch controller, sensor hub, or power-management device increases bus loading beyond what the host can drive reliably. The two-channel architecture allows SDA and SCL to be regenerated together, and the 3.6 V maximum VCC is compatible with common 3.3 V portable-device rails. Since the I/O is 5.5 V tolerant, mixed-voltage bus signaling is possible where pull-ups and connected-device ratings permit. In a compact layout, prioritize short routing, solid ground return, and correct pull-up placement because assembly density can make bus-branch capacitance and ground bounce more significant than in a large controller board.

🌐

Communications Equipment

The PCA9515APWT is suitable for communications equipment that uses I2C to configure an analog, radio, or network interface device on a separate board segment. Regenerating the clock and data signals helps decouple the interface IC from connector, cable, and peripheral capacitance, improving transition reliability at standard Fast-mode speeds. The device's active-high enable input also provides a basic mechanism for controlling repeater participation during startup or reset. Designers should confirm that the interface chip supports clock stretching and that its pins remain compatible with the repeater's open-drain behavior. Keep both repeated channels in the same clock domain and preserve a low-impedance ground path between the two bus segments.

What is the PCA9515APWT?
The PCA9515APWT is a Texas Instruments 2-channel bidirectional I2C bus and SMBus repeater operating from 2.3 V to 3.6 V at up to 400 kHz. According to the manufacturer product page, it provides two identical bidirectional open-drain buffer circuits and is packaged in an 8-pin TSSOP (PW) package. It is used to regenerate I2C signals, isolate bus loading, and extend reliable communication between a host and remote peripheral.
What is the operating voltage of PCA9515APWT?
The PCA9515APWT operates from 2.3 V to 3.6 V VCC, while its I2C I/O and enable inputs are specified as 5.5 V tolerant. The Texas Instruments manufacturer page identifies the device as a 2.3 V to 3.6 V, 400 kHz I2C/SMBus buffer. The supply range applies to VCC; the 5.5 V tolerance rating does not change the device's permitted operating supply range.
How many I2C channels does PCA9515APWT have?
The PCA9515APWT has two independent bidirectional buffer channels. The Texas Instruments product description identifies it as a 2-bit dual bidirectional I2C bus and SMBus repeater with two identical open-drain buffer circuits. This differs from a single-channel unidirectional level translator because each channel can carry clock and data signals in either direction.
What is the maximum I2C speed of PCA9515APWT?
The PCA9515APWT supports I2C and SMBus operation up to 400 kHz. According to the Texas Instruments manufacturer product page, it is a 400 kHz I2C/SMBus buffer. The practical bus speed also depends on pull-up resistance, total bus capacitance, clock stretching behavior, and the electrical characteristics of the connected controller and peripherals.
Where can I download the PCA9515APWT datasheet PDF?
The PCA9515APWT datasheet is available through the Texas Instruments product page at https://www.ti.com/product/PCA9515A/part-details/PCA9515APWT. The manufacturer page identifies the PCA9515A family and the PCA9515APWT ordering variant. Use the manufacturer datasheet for the authoritative pin descriptions, enable timing, electrical characteristics, and application guidance.
Where can I find the PCA9515APWT pinout?
The PCA9515APWT pinout is defined in the Texas Instruments PCA9515A manufacturer datasheet under the pin configuration and pin functions tables. The device uses an 8-pin TSSOP (PW) package. Use the datasheet pin-description table when assigning PCB nets because the exposed signal names and enable-pin function must match the exact device revision.
What is the best drop-in replacement for PCA9515APWT?
PCA9515APWR is the closest same-package replacement identified for the PCA9515APWT, using the same 8-pin TSSOP (PW) footprint and the same PCA9515A 2-channel, 400 kHz I2C/SMBus repeater function. The primary ordering distinction is the suffix and packaging code. Confirm the exact tape-and-reel or other delivery option required by the production BOM before substitution.
Can PCA9515APWR replace PCA9515APWT?
PCA9515APWR can serve as a functional and footprint-compatible alternative to PCA9515APWT because both are listed as 8-TSSOP, 2-channel, 400 kHz PCA9515A-family I2C redrivers from Texas Instruments. The package family and core electrical function match, but the ordering suffix determines the specific delivery option. Verify packaging details against the manufacturer ordering information.
PCA9515APWT vs PCA9515APWR: which one should I choose?
Choose PCA9515APWT when the exact manufacturer ordering code and its corresponding delivery format are required; choose PCA9515APWR when that suffix matches the procurement or assembly package. Both devices are identified as Texas Instruments 8-TSSOP, 2-channel, 400 kHz I2C redrivers. The electrical comparison is therefore less significant than confirming the exact suffix, reel orientation, quantity, and manufacturer ordering code.
When should I choose PCA9515APWT over a direct I2C connection?
Choose PCA9515APWT when capacitance, wiring distance, branch loading, or electrical isolation makes a direct I2C connection unreliable. Its two bidirectional repeater channels can regenerate the bus waveform and separate a heavily loaded segment from the host controller. A direct connection remains preferable when the bus is short, capacitance is low, and no signal regeneration is required.
Is PCA9515APWT suitable for long-distance I2C communication?
The PCA9515APWT is suitable for extending an I2C segment when used with correct pull-ups and careful board-level signal-integrity design. Its two bidirectional channels operate up to 400 kHz and regenerate degraded bus signals, but the supported cable length still depends on capacitance, pull-up strength, clock rate, topology, and interference. Treat the repeater as a bus conditioner rather than an unlimited distance guarantee.
Where can I buy PCA9515APWT online?
Use the Request a Quote form on this page to request PCA9515APWT availability, lead time, and a current quotation for the exact 8-pin TSSOP (PW) ordering variant. The manufacturer lists PCA9515APWT as a 2-bit, 2.3 V to 3.6 V, 400 kHz I2C/SMBus buffer in an 8-pin TSSOP package. The form is the appropriate channel for a current commercial quotation.
What is the price of PCA9515APWT?
The current PCA9515APWT quotation is handled through the Request a Quote form on this page rather than through a static price statement. The request should identify the exact PCA9515APWT suffix, required quantity, and tape-and-reel packaging expectation. This avoids pricing a different ordering code or an incompatible delivery format.
What is the lead time and stock status of PCA9515APWT?
The current lead time and stock status for PCA9515APWT should be confirmed through the Request a Quote form on this page. The Texas Instruments product page identifies the exact part as an 8-pin TSSOP (PW) device, and the sourcing record identifies it as a standard catalog part. Provide the required quantity and production schedule with the request so the current allocation can be confirmed.
What are the key specifications of PCA9515APWT that engineers should know?
The PCA9515APWT is a Texas Instruments dual bidirectional I2C/SMBus repeater with two channels, a 2.3 V to 3.6 V supply range, 400 kHz maximum bus frequency, 5.5 V tolerant I2C I/O and enable inputs, open-drain signaling, and an active-high enable. It uses an 8-pin TSSOP (PW) package. According to the manufacturer product page, these features position it for bus extension, loading isolation, and signal regeneration.

এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা PCA9515APWT — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।

নির্বাচন গাইড

Choose PCA9515APWT when the design requires a Texas Instruments dual bidirectional I2C/SMBus repeater in the 8-pin TSSOP (PW) package and the exact ordering suffix matches the production BOM. It is appropriate for extending an I2C segment, isolating high-capacitance peripherals, or regenerating bus signals at up to 400 kHz. PCA9515APWR is the closest footprint-compatible alternative identified and provides the same stated 2-channel, 400 kHz functionality; select it when its ordering code and delivery format better match procurement or assembly requirements. A direct I2C connection is preferable when the bus is short, capacitance is low, and no regeneration is needed. Before using either repeater, verify pull-up placement, enable-state requirements, sink-current limits, clock-stretching behavior, and the voltage ratings of every peripheral on the isolated segment.

বিকল্পের সাথে তুলনা

পারামিটার এই পণ্য PCA9515APWR
Brand Texas Instruments Texas Instruments
Package 8-pin TSSOP (PW) 8-pin TSSOP (PW)
Product Type Dual bidirectional I2C/SMBus repeater Dual bidirectional I2C/SMBus repeater
Number of Channels 2 channels 2 channels
Supply Voltage 2.3 V to 3.6 V 2.3 V to 3.6 V
Maximum Bus Frequency 400 kHz 400 kHz
I/O Type Open-drain bidirectional Open-drain bidirectional
I/O Voltage Tolerance 5.5 V tolerant 5.5 V tolerant
Enable Input Active-high Active-high
Supported Protocol I2C and SMBus I2C and SMBus

মূল পার্থক্যসমূহ

  • Direct footprint-compatible alternative (বনামPCA9515APWR)
  • Dual-channel bidirectional architecture (বনামPCA9515APWR)
  • Mixed-voltage bus compatibility (বনামPCA9515APWR)

ডিজাইন নোট

Place the PCA9515APWT near the boundary between the host-side and load-side I2C segments. Route SDA and SCL as a closely coupled pair, keep the traces short, provide a continuous ground reference, and avoid crossing switching-power or high-speed digital nets. The 400 kHz rating does not eliminate rise-time degradation from long traces, excessive capacitance, or poorly placed pull-up resistors.

Install pull-up resistors on each isolated bus segment rather than assuming that the host-side pull-ups will serve the load side. Size the resistors from the bus voltage, capacitance, target rise time, and the connected devices' sink-current limits. The open-drain repeater requires pull-ups for valid high levels; missing, oversized, or incorrectly located pull-ups are common causes of intermittent I2C failures.

Decouple VCC with a local high-frequency ceramic capacitor and provide a low-impedance ground return. Keep the repeater supply stable while the I2C bus is active because supply disturbance can appear as edge jitter or communication errors. The 2.3 V to 3.6 V VCC range is the operating supply specification; the 5.5 V tolerant I/O rating does not authorize operation with VCC above 3.6 V.

Verify the complete network rather than only the controller and repeater. Account for peripheral input capacitance, connector capacitance, pull-up current, clock stretching, and the timing budget at 400 kHz. If the bus must operate near its upper frequency limit, measure SCL and SDA rise times and ringing at the load-side endpoints, then adjust pull-up strength or topology based on those measurements.

কমপ্লায়েন্স তথ্য

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
লিড ফ্রি
Unknown
হ্যালোজেন ফ্রি
Unknown
কনফ্লিক্ট মিনারেলস
Unknown

Compliance values were not explicitly established by the manufacturer product information identified for this device. AEC-Q100 is listed as not applicable because this product is an interface IC rather than an automotive-qualified device designation.

ডেটা যাচাই করা হয়েছে: 2026-11-19 — ডেটা XAIPART-এর কম্পোনেন্ট ইঞ্জিনিয়ারিং টিম দ্বারা যাচাই ও কিউরেট করা হয়েছে

সম্পর্কিত অনুসন্ধান

PCA9515APWT datasheet PCA9515APWT pinout PCA9515APWT datasheet pdf PCA9515APWT equivalent PCA9515APWT replacement PCA9515APWT vs PCA9515APWR PCA9515APWT footprint PCA9515APWT application circuit PCA9515APWT price Texas Instruments PCA9515APWT PCA9515APWT 400kHz I2C buffer PCA9515A 8-TSSOP buffer

সম্পর্কিত কম্পোনেন্ট ও শর্তাবলী

Texas Instruments PCA9515APWT PCA9515A PCA9515APWR I2C SMBus bidirectional buffer bus repeater redriver interface IC signal buffer open-drain I/O active-high enable mixed-mode operation BiCMOS TSSOP-8 PW package surface mount bus extension signal integrity capacitive loading clock stretching pull-up resistor 400 kHz I2C 2.3 V to 3.6 V supply
তাৎক্ষণিক বিলওয়াছে রেকোজিউইট
সম্পূর্ণ বিবরণ পূরণ করুন — আমাদের সেলস টিম 24 ঘণ্টার মধ্যে উত্তর দেবে
পার্ট নম্বর উৎপাদক প্যাকেজ QTY লক্ষ্যমূল্য প্রসারিত
✓
বিল প্রস্তুত করা হয়েছে!

আমরা ২৪ ঘণ্টার মধ্যে আপনার ইমেইলে প্রত্যুত্তর দেব

1
RFQ জমা হয়েছে
2
কোটেশন পাওয়া গেছে
3
অর্ডার দেওয়া হয়েছে
4
পেমেন্ট
5
শিপ করা হয়েছে
6
ডেলিভারি হয়েছে
RFQ বিবরণ দেখুন