PCA9515APWT - 2-Channel I2C Buffer, 400kHz | Texas Instruments
Артикул: PCA9515APWT ✓ АктивенPCA9515APWT Обзор
An I2C buffer or repeater is an interface IC that regenerates and electrically isolates a bidirectional bus segment. I2C and SMBus use open-drain signaling, so a buffer can reduce loading, restore signal rise time, isolate capacitive loading, and extend usable bus distance without changing the logical bus protocol. The PCA9515A belongs to the broader signal-buffer and repeater category within interface ICs, supporting embedded systems where a controller, sensor, EEPROM, or other peripheral sits behind a long or heavily loaded interconnect.
The main features of the PCA9515APWT include two identical bidirectional buffer channels, 2.3 V to 3.6 V operation, 400 kHz bus speed, 5.5 V tolerant I2C I/O, and mixed-mode signal support. The active-high repeater-enable input allows the device to be placed into a controlled operating state in designs that require bus segmentation or repeatable startup behavior. Open-drain I/O preserves the wired-AND nature of I2C while allowing the repeater to participate in normal clock and data signaling.
The device contains two identical bidirectional open-drain buffer circuits intended for I2C and SMBus systems. Its BiCMOS implementation combines CMOS logic with bipolar output characteristics, supporting mixed-mode signal operation while maintaining compatibility with the electrical conventions used by I2C-compatible peripherals. The buffered channels are intended to improve signal integrity when capacitance, wiring distance, or multiple bus branches create excessive loading on a host bus segment.
Typical applications include extending an I2C bus between a microcontroller and remote sensors, isolating a high-capacitance section of a bus, separating power domains with compatible logic levels, and preserving signal quality in industrial, embedded, and consumer electronics. The PCA9515APWT is most appropriate when the system uses a 400 kHz or lower I2C-compatible bus and requires two bidirectional repeater channels rather than a unidirectional level translator.
Designers should check the device enable state, supply decoupling, pull-up resistor placement, and the voltage tolerance of every connected I2C peripheral before deployment. Pull-ups must be placed on the correct bus segment and sized for its voltage, capacitance, sink current, and speed. The TSSOP footprint also requires adequate copper area and thermal planning even though the device is intended for low-power bus management.
This product page combines the manufacturer specification, package information, sourcing links, interface guidance, and practical bus-conditioning considerations. It is intended to help engineers identify whether the PCA9515APWT matches the required channel count, supply range, bus speed, and TSSOP footprint before placing it into an I2C or SMBus design.
Аналоги без доработки для PCA9515APWT — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с PCA9515APWT (тот же форм-фактор и посадочное место).
PCA9515APWR
✅ Прямая заменаУточнить цену
Открыть даташит →PCA9515APWT Характеристики
| Product Type | Dual bidirectional I2C bus and SMBus repeater |
| Number of Buffer Channels | 2 channels |
| Supply Voltage Range | 2.3 V to 3.6 V VCC |
| Maximum I2C Bus Frequency | 400 kHz |
| I2C I/O Voltage Tolerance | 5.5 V tolerant |
| Enable Input Voltage Tolerance | 5.5 V tolerant |
| I2C Interface Type | Open-drain |
| Signal Direction | Bidirectional |
| Repeater Enable | Active-high |
| Supported Protocol | I2C and SMBus |
| Mixed-Mode Operation | Supported |
| Process Technology | BiCMOS |
| Корпус | 8-pin TSSOP (PW) |
| Package Dimensions | 0.173 inch, 4.40 mm width |
| Тип монтажа | Surface mount |
| Ordering Suffix | PWT |
Руководство по цоколевке PCA9515APWT в корпусе 0.173 inch, 4.40 mm width
Цоколевка для PCA9515APWT (корпус 0.173 inch, 4.40 mm width). Нумерация выводов, функции и схемы подключения определены в техническом описании производителя. Обратитесь к нему для точного посадочного места и рекомендаций по пайке.
Нет подробных данных о распиновке для PCA9515APWT.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
PCA9515APWT подходит для 6 применениеs: I2C Bus Extension, Sensor Hub Isolation, Embedded EEPROM Access, Industrial Control Module, Portable Device Expansion, Communications Equipment.
I2C Bus Extension
The PCA9515APWT fits bus-extension designs where a microcontroller must communicate with a remote sensor, memory device, or transceiver across a longer PCB interconnect or cable segment. Its two bidirectional channels can regenerate clock and data signals, while the 400 kHz maximum operating rate matches standard Fast-mode I2C systems. The 2.3 V to 3.6 V supply range supports common 2.5 V and 3.3 V logic environments. The main design consideration is pull-up placement: each isolated bus segment requires correctly sized pull-ups, and excessive capacitance or resistance can still prevent reliable operation at the selected clock rate.
Рекомендуется
Sensor Hub Isolation
The PCA9515APWT is useful in sensor-hub designs where several temperature, light, motion, or environmental sensors create additional bus capacitance behind a host controller. The two bidirectional repeater channels can isolate those loads and restore signal levels without changing the I2C protocol. Its 400 kHz rating is appropriate for Fast-mode sensor polling, while 5.5 V tolerant I/O helps accommodate mixed-voltage peripherals when the bus pull-up voltage remains compatible. Keep the repeater close to the host-side bus, place the load-side pull-ups near the remote devices, and avoid combining long stubs with high capacitance without signal-integrity analysis.
Рекомендуется
Embedded EEPROM Access
The PCA9515APWT can separate a microcontroller from an EEPROM or other configuration memory when PCB capacitance or connector loading makes the direct bus unreliable. Bidirectional operation is essential because I2C uses the same SDA and SCL conductors for control and returned data. The device's two channels allow SCL and SDA to be buffered independently, and its open-drain implementation remains compatible with standard I2C pull-up networks. For reliable operation, calculate pull-up resistance from bus capacitance and sink-current limits, confirm that the EEPROM supports the selected operating frequency, and provide a continuous ground reference across the separated segment.
Рекомендуется
Industrial Control Module
The PCA9515APWT is applicable in industrial control modules that connect a controller to remote sensors, actuators, or operator-interface devices over an I2C-compatible link. Its 2.3 V to 3.6 V operating supply and 400 kHz speed align with embedded 3.3 V control systems, while the repeater channels improve isolation from long wiring and connector capacitance. Industrial installations also require attention to grounding, surge exposure, pull-up fault conditions, and the enable pin behavior during reset. The TSSOP package supports compact controller boards, provided the layout preserves short return paths and avoids routing sensitive bus traces beside high-current switching nodes.
Рекомендуется
Portable Device Expansion
The PCA9515APWT can condition an I2C link in a portable device when a display, touch controller, sensor hub, or power-management device increases bus loading beyond what the host can drive reliably. The two-channel architecture allows SDA and SCL to be regenerated together, and the 3.6 V maximum VCC is compatible with common 3.3 V portable-device rails. Since the I/O is 5.5 V tolerant, mixed-voltage bus signaling is possible where pull-ups and connected-device ratings permit. In a compact layout, prioritize short routing, solid ground return, and correct pull-up placement because assembly density can make bus-branch capacitance and ground bounce more significant than in a large controller board.
Рекомендуется
Communications Equipment
The PCA9515APWT is suitable for communications equipment that uses I2C to configure an analog, radio, or network interface device on a separate board segment. Regenerating the clock and data signals helps decouple the interface IC from connector, cable, and peripheral capacitance, improving transition reliability at standard Fast-mode speeds. The device's active-high enable input also provides a basic mechanism for controlling repeater participation during startup or reset. Designers should confirm that the interface chip supports clock stretching and that its pins remain compatible with the repeater's open-drain behavior. Keep both repeated channels in the same clock domain and preserve a low-impedance ground path between the two bus segments.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для PCA9515APWT — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | PCA9515APWR |
|---|---|---|
| Brand | Texas Instruments | Texas Instruments |
| Package | 8-pin TSSOP (PW) | 8-pin TSSOP (PW) |
| Product Type | Dual bidirectional I2C/SMBus repeater | Dual bidirectional I2C/SMBus repeater |
| Number of Channels | 2 channels | 2 channels |
| Supply Voltage | 2.3 V to 3.6 V | 2.3 V to 3.6 V |
| Maximum Bus Frequency | 400 kHz | 400 kHz |
| I/O Type | Open-drain bidirectional | Open-drain bidirectional |
| I/O Voltage Tolerance | 5.5 V tolerant | 5.5 V tolerant |
| Enable Input | Active-high | Active-high |
| Supported Protocol | I2C and SMBus | I2C and SMBus |
Ключевые отличия
- Direct footprint-compatible alternative (против PCA9515APWR)
- Dual-channel bidirectional architecture (против PCA9515APWR)
- Mixed-voltage bus compatibility (против PCA9515APWR)
Заметки по проектированию
Place the PCA9515APWT near the boundary between the host-side and load-side I2C segments. Route SDA and SCL as a closely coupled pair, keep the traces short, provide a continuous ground reference, and avoid crossing switching-power or high-speed digital nets. The 400 kHz rating does not eliminate rise-time degradation from long traces, excessive capacitance, or poorly placed pull-up resistors.
Install pull-up resistors on each isolated bus segment rather than assuming that the host-side pull-ups will serve the load side. Size the resistors from the bus voltage, capacitance, target rise time, and the connected devices' sink-current limits. The open-drain repeater requires pull-ups for valid high levels; missing, oversized, or incorrectly located pull-ups are common causes of intermittent I2C failures.
Decouple VCC with a local high-frequency ceramic capacitor and provide a low-impedance ground return. Keep the repeater supply stable while the I2C bus is active because supply disturbance can appear as edge jitter or communication errors. The 2.3 V to 3.6 V VCC range is the operating supply specification; the 5.5 V tolerant I/O rating does not authorize operation with VCC above 3.6 V.
Verify the complete network rather than only the controller and repeater. Account for peripheral input capacitance, connector capacitance, pull-up current, clock stretching, and the timing budget at 400 kHz. If the bus must operate near its upper frequency limit, measure SCL and SDA rise times and ringing at the load-side endpoints, then adjust pull-up strength or topology based on those measurements.
Информация о соответствии
Compliance values were not explicitly established by the manufacturer product information identified for this device. AEC-Q100 is listed as not applicable because this product is an interface IC rather than an automotive-qualified device designation.