Texas Instruments

PCA9544ADW - 4-Channel I2C/SMBus Multiplexer | Texas Instruments

MPN: PCA9544ADW ✓ সক্রিয়
2.3 V to 5.5 V Vdss SOIC (DW) Package
সর্বনিম্ন অর্ডার পরিমাণ: 1 |

PCA9544ADW সারাংশ

Texas Instruments PCA9544ADW is a four-channel I2C and SMBus multiplexer with interrupt handling and voltage translation, supplied in a 20-pin SOIC (DW) package. It operates from a 2.3 V to 5.5 V supply and distributes one upstream SCL/SDA pair across four downstream SCx/SDx channel pairs. Only one downstream channel is selected at a time through the multiplexer's I2C control register.

An I2C multiplexer is an interface IC that extends a shared two-wire bus to multiple peripheral branches while preventing signals from inactive branches from affecting the active branch. The PCA9544ADW belongs to the interface-controller hierarchy, connecting a host controller and several sensors, EEPROMs, amplifiers, or other I2C peripherals. Its translating architecture and interrupt inputs support systems in which attached devices require bus isolation or level translation.

The principal functions are four-channel multiplexing, bidirectional voltage translation, and individual downstream interrupt inputs. Four interrupt lines allow a system controller to identify which selected peripheral asserted its interrupt signal. The device also consolidates control of channel selection through the upstream I2C bus, allowing firmware to change the active downstream path without rewiring hardware or mechanically switching buses.

The translating design separates the upstream SCL/SDA pair from the four downstream SCx/SDx pairs. This arrangement provides electrical isolation between the host-side bus and each selected peripheral branch while retaining a compact 20-pin surface-mount implementation. The interrupt structure makes the device especially useful for mixed-signal, embedded, and sensor systems in which several downstream devices may request service from one shared controller.

Typical uses include environmental and industrial sensor nodes, configuration registers accessed through EEPROM, portable measurement equipment, communication modules, and compact control boards that connect more I2C targets than the host bus can address directly. The PCA9544ADW is also appropriate when several embedded subsystems require controlled access to a common peripheral set.

Designers should confirm the upstream and downstream voltage limits, pull-up requirements, channel-selection logic, and interrupt polarity in the manufacturer datasheet before committing a board layout. The SOIC footprint requires adequate lead spacing and process-control measures during assembly. PCB routing should keep SCL and SDA paths short, maintain continuous ground references, and avoid introducing bus-stub capacitance that could impair signal integrity.

This product page combines the manufacturer identification, verified source links, structured technical characteristics, application guidance, and a qualified cross-manufacturer replacement assessment. It also distinguishes confirmed device functions from electrical details that must be established from the complete manufacturer datasheet before layout or production release.

এর জন্য ড্রপ-ইন বিকল্প PCA9544ADW — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।

PCA9544AD,118

✅ ড্রপ-ইন
📦 SOIC-20
Same 4-channel PCA9544A multiplexer function and 20-pin SOIC format; manufacturer differs, while address, interrupt-polarity, and timing differences remain 0% confirmed from the cited listing

📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)

PCA9544ADW বিশেষণ

Device Type I2C/SMBus multiplexer with interrupt and voltage translation
Number of Channels 4 channels
Supply Voltage Range 2.3 V to 5.5 V
Upstream Bus 1 SCL/SDA pair
Downstream Buses 4 SCx/SDx pairs
Channel Selection 1-of-4 selection
Interrupt Inputs 4 inputs
Voltage Translation Bidirectional translating architecture
Control Interface I2C bus
Supported Serial Protocol I2C and SMBus
Package Type SOIC (DW)
পিনের সংখ্যা 20 pins

PCA9544ADW soic (dw) পিন কনফিগারেশন গাইড

PCA9544ADW (soic (dw) প্যাকেজ)-এর পিন কনফিগারেশন। পিন নম্বরিং, ফাংশন এবং সংযোগ ডায়াগ্রাম প্রস্তুতকারকের ডেটাশিটে সংজ্ঞায়িত করা আছে। সঠিক ফুটপ্রিন্ট এবং সোল্ডারিং নির্দেশিকার জন্য এটি দেখুন।

PCA9544ADW-এর জন্য soic (dw) প্যাকেজ পিনআউট ডায়াগ্রাম

এর জন্য বিস্তারিত পিনআউট ডেটা পাওয়া যায়নি PCA9544ADW.

দেখুন ডেটাশিট সম্পূর্ণ পিন কনফিগারেশনের জন্য।

সাধারণ ব্যবহার

PCA9544ADW এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Industrial Sensor Hub, Portable Environmental Monitor, EEPROM and Configuration Hub, Communication Module Expansion, Mixed-Signal Audio Interface, Robotics and Control Module.

🏭

Industrial Sensor Hub

The PCA9544ADW fits an industrial sensor hub that must connect several I2C sensors to one host controller while preserving a controlled route for each branch. Its four downstream SCx/SDx pairs allow the controller to select one sensor at a time, and the four interrupt inputs provide a mechanism for downstream devices to request attention. The 2.3 V to 5.5 V operating range supports compact embedded systems, while the translating arrangement helps separate host-side and peripheral-side bus levels. Confirm industrial temperature requirements, logic thresholds, pull-up values, and channel isolation limits in the manufacturer datasheet before releasing the PCB.

🧩

Portable Environmental Monitor

The PCA9544ADW is useful in a portable environmental monitor that combines temperature, humidity, gas, and motion-related sensing devices on a shared I2C bus. Four selectable downstream branches prevent devices on inactive channels from participating in the current transfer, helping the controller address sensors in a controlled sequence. The 20-pin SOIC package also leaves more board area than a larger package for battery, display, and processing circuitry. Before layout, verify the permitted operating temperature, voltage levels for every sensor, required bus pull-ups, and whether the interrupt lines are sufficient for the chosen sensor set.

🖥️

EEPROM and Configuration Hub

The PCA9544ADW can organize an embedded control board around several EEPROMs or other configuration peripherals. The host SCL/SDA pair connects to the upstream side, while the four SCx/SDx pairs provide separate downstream routes for individual devices. Because only one channel is selected at a time, firmware can access each configuration target without placing every peripheral permanently on the same electrical branch. The translating architecture adds value when the host and peripheral sides do not share identical logic levels; confirm address behavior, bus capacitance, pull-up placement, and channel-switching timing in the manufacturer datasheet.

🌐

Communication Module Expansion

The PCA9544ADW fits a communication module that connects an embedded host to several I2C transceivers, codecs, or configuration blocks. Its one-of-four channel selection allows the controller to isolate downstream branches and address only the active peripheral, which can simplify firmware organization and reduce unwanted bus interactions. The bidirectional translation function is useful when upstream and downstream devices operate at different logic levels. For a production design, verify every branch's voltage range, maximum bus rate, pull-up strategy, interrupt behavior, and whether the module's enclosure or grounding arrangement introduces additional bus-coupling concerns.

🎧

Mixed-Signal Audio Interface

The PCA9544ADW can support a mixed-signal audio interface that combines I2C-controlled codecs, amplifiers, and configuration registers. The device's four SCx/SDx branches offer a structured way to isolate peripheral routes, while its interrupt inputs allow a selected audio component to notify the controller. This arrangement is particularly relevant when the host and peripheral sides require different logic levels. Signal-chain performance still depends on the audio devices themselves, so the mux should be placed away from sensitive analog traces and switching nodes. Use short, continuous-ground SCL and SDA routes, then verify channel capacitance and timing against the complete bus specification.

🤖

Robotics and Control Module

The PCA9544ADW is appropriate for a compact robotics or automation module that must manage several embedded subsystems over one host bus. Four downstream channels can support sensor controllers, actuator interfaces, or configuration devices, and the interrupt inputs can identify a selected peripheral requesting service. The 20-pin SOIC package supports conventional surface-mount assembly, although lead clearance must be considered in dense robotics electronics. Validate the full operating temperature range, voltage levels, isolation behavior, and interrupt polarity for each attached subsystem. Mechanical vibration and temperature changes should also be evaluated at the system level rather than inferred from the mux specifications alone.

What is the PCA9544ADW?
The PCA9544ADW is a four-channel I2C and SMBus multiplexer with interrupt handling and voltage translation from Texas Instruments. According to the manufacturer product page, it accepts a 2.3 V to 5.5 V supply and fans one upstream SCL/SDA pair out to four downstream SCx/SDx pairs in a 20-pin SOIC (DW) package.
How many I2C channels does the PCA9544ADW provide?
The PCA9544ADW provides four downstream I2C channels controlled from one upstream bus. According to the Texas Instruments product page, one upstream SCL/SDA pair is distributed to four SCx/SDx channel pairs, and only one channel is selected at a time through the programmable control register.
What is the operating voltage of PCA9544ADW?
The PCA9544ADW operates from a 2.3 V to 5.5 V supply. According to the Texas Instruments product page, that figure describes the device's specified supply range; separate upstream and downstream translation voltage limits should be confirmed from the complete manufacturer datasheet before design release.
Does PCA9544ADW support SMBus and interrupt signaling?
Yes, the PCA9544ADW supports both I2C and SMBus operation and includes individual interrupt inputs. According to the Texas Instruments product description, four interrupt inputs correspond to the four downstream channels, allowing a controller to identify a selected peripheral that requests service.
Where can I download the PCA9544ADW datasheet PDF?
The official PCA9544A product page on Texas Instruments is the appropriate starting point for the manufacturer datasheet and supporting documents. It identifies PCA9544ADW as a 20-pin SOIC device; use the linked data-sheet document for the complete pin descriptions, electrical limits, control-register map, and application guidance.
Where can I find the PCA9544ADW pinout?
The PCA9544ADW pinout is defined by the 20-pin SOIC (DW) package and the manufacturer's pin-description table. The official PCA9544A product page confirms the package and pin count; use the corresponding data-sheet pinout when assigning SCL, SDA, SCx, SDx, address, reset, and interrupt functions to the PCB.
What can replace the PCA9544ADW?
The NXP Semiconductors PCA9544AD,118 is a documented four-channel PCA9544A-family alternative in a 20-pin SO package, but it is not manufactured by Texas Instruments. According to the NXP data-sheet listing, it implements a one-of-four bidirectional I2C multiplexer; verify address compatibility, interrupt polarity, timing, and pin mapping before substitution.
Is PCA9544ADW the same as PCA9544AD,118?
No, they are not the same manufacturer orderable part. The PCA9544ADW is the Texas Instruments 20-pin SOIC version, while PCA9544AD,118 is an NXP Semiconductors 20-SO version of the PCA9544A family; they may support the same four-channel multiplexer function, but production substitution still requires a pin and register-level review.
PCA9544ADW vs PCA9544AD,118 - which is better for an existing PCB?
The Texas Instruments PCA9544ADW is the preferred choice when continuity with the original manufacturer and procurement qualification matters. The NXP PCA9544AD,118 offers the same four-channel I2C multiplexer concept in a 20-pin SO package, but a direct replacement requires verification of pinout, address behavior, interrupt polarity, voltage translation limits, and timing.
PCA9544ADW vs PCA9545ADW - what is the difference?
Both are four-channel PCA9544A-family interface devices, but the PCA9545ADW is not established here as a verified drop-in substitute for the PCA9544ADW. The manufacturer product page confirms the PCA9544ADW's four-channel multiplexing, interrupt, and translation functions; compare the PCA9545ADW pin assignments, reset behavior, and interrupt implementation in its own datasheet before using it interchangeably.
When should I choose PCA9544ADW over another I2C multiplexer?
Choose the PCA9544ADW when a design needs four downstream I2C or SMBus branches, bidirectional voltage translation, and per-channel interrupt inputs in a 20-pin SOIC footprint. According to the Texas Instruments product page, it supports 2.3 V to 5.5 V operation and one-of-four channel selection, making it appropriate for multi-sensor and multi-embedded-subsystem interfaces.
Is PCA9544ADW suitable for an industrial sensor interface?
The PCA9544ADW is functionally suitable for an industrial sensor interface that needs one host bus to address several I2C peripherals. Its four selectable SCx/SDx branches and four interrupt inputs can reduce wiring and controller burden; confirm operating temperature, logic thresholds, isolation requirements, and regulatory needs before production use.
How should the PCA9544ADW be used with multiple I2C sensors?
Connect the host SCL/SDA lines to the upstream bus, attach each sensor branch to a separate SCx/SDx channel, and use the I2C control register to select the branch being addressed. According to the NXP-family data-sheet description, only one downstream channel is active at a time, so firmware should avoid simultaneous access to peripherals on different branches.
Where to buy PCA9544ADW online?
Use the Request a Quote form on this page to request PCA9544ADW availability, order quantities, and current commercial terms. The official Texas Instruments part-details page identifies the exact MPN and package, while the verified distributor listings confirm that the component is catalogued for procurement.
What is the price and lead time for PCA9544ADW?
Current price and lead time should be requested through the Request a Quote form on this page because commercial terms can vary with quantity, package, and supply conditions. The verified distributor listings include the exact PCA9544ADW orderable code, but they do not provide a qualifying quantity-break price table for this product.
Is PCA9544ADW in stock?
Submit a stock request with the Request a Quote form on this page to confirm the current PCA9544ADW quantity. The verified distributor listings describe catalogued availability or purchasing options, but they do not provide a stable inventory quantity that can be represented as a current stock guarantee.

এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা PCA9544ADW — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।

নির্বাচন গাইড

Choose the PCA9544ADW when the design requires four controlled I2C or SMBus branches, bidirectional voltage translation, individual interrupt inputs, and a 20-pin SOIC implementation. Its 2.3 V to 5.5 V operating range and manufacturer-defined one-of-four selection make it suitable for embedded systems with several sensors, EEPROMs, or peripheral controllers. The NXP PCA9544AD,118 is a relevant second-source candidate in the same PCA9544A family and a 20-pin SO package, but do not approve it as a drop-in replacement without checking pin assignments, control-register behavior, address options, interrupt polarity, voltage limits, and timing. PCA9545ADW and PCA9546ADWR appear in comparison listings, but the cited material does not establish them as verified pin-compatible substitutes for this exact design. For a new production release, use the complete Texas Instruments datasheet and perform board-level bus timing and pull-up validation.

বিকল্পের সাথে তুলনা

পারামিটার এই পণ্য PCA9544AD,118
Manufacturer Texas Instruments NXP Semiconductors
Package SOIC-20 (DW) SOIC-20
Multiplexer Channels 4 4
Supported Buses I2C and SMBus I2C
Voltage Translation Bidirectional translating architecture Bidirectional translation
Interrupt Inputs 4 4
Upstream Bus 1 SCL/SDA pair 1 SCL/SDA pair
Downstream Buses 4 SCx/SDx pairs 4 SCx/SDx pairs

মূল পার্থক্যসমূহ

  • Four individually interruptable downstream branches (বনামPCA9544AD,118)
  • Bidirectional level translation in the same multiplexer function (বনামPCA9544AD,118)
  • Defined 2.3 V to 5.5 V device operating range (বনামPCA9544AD,118)

ডিজাইন নোট

Route the upstream SCL/SDA pair and all four downstream SCx/SDx branches as short, continuous traces with a nearby ground reference. Place each branch's required pull-up network at the appropriate end of that branch, and avoid long stubs or test-point loops that add excessive capacitance. Confirm pull-up voltage and resistance against the logic level and bus-rate requirements in the manufacturer datasheet.

Do not assume that all downstream peripherals can be addressed simultaneously. The PCA9544ADW selects one downstream channel at a time, so firmware should complete or suspend a transfer before changing channels. Also avoid assuming that the operating supply range establishes every allowed upstream or downstream voltage; verify the separate logic-level ranges in the complete manufacturer datasheet.

Treat SCL, SDA, SCx, and SDx as paired communication nets with controlled return paths. Keep the multiplexer away from switching regulators, inductors, and high-current power traces where practical. Account for connector and test-point capacitance, and use the datasheet timing and capacitance limits when extending any downstream branch beyond the recommended PCB topology.

The 20-pin SOIC package is straightforward for conventional reflow assembly but requires adequate spacing from tall components and board edges. Maintain the manufacturer's land pattern and solder recommendations, inspect the pin-one orientation during assembly, and keep the interrupt traces away from noisy analog or switching nodes because an unintended edge on these inputs could create a false service request.

কমপ্লায়েন্স তথ্য

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
লিড ফ্রি
Unknown
হ্যালোজেন ফ্রি
Unknown
কনফ্লিক্ট মিনারেলস
Unknown

The verified manufacturer and distributor listings do not provide explicit compliance declarations for this exact orderable part. AEC-Q100 is not applicable because this device is not an automotive-qualified component in the cited information.

ডেটা যাচাই করা হয়েছে: 2026-11-10 — ডেটা XAIPART-এর কম্পোনেন্ট ইঞ্জিনিয়ারিং টিম দ্বারা যাচাই ও কিউরেট করা হয়েছে

সম্পর্কিত অনুসন্ধান

PCA9544ADW PCA9544ADW datasheet PCA9544ADW datasheet pdf PCA9544ADW pinout PCA9544ADW equivalent PCA9544ADW replacement PCA9544ADW vs PCA9544AD,118 PCA9544ADW cross reference Texas Instruments PCA9544ADW PCA9544ADW price PCA9544ADW stock PCA9544A 4-channel I2C multiplexer

সম্পর্কিত কম্পোনেন্ট ও শর্তাবলী

Texas Instruments PCA9544ADW PCA9544A PCA9544AD,118 PCA9545ADW PCA9546ADWR NXP Semiconductors I2C SMBus I2C multiplexer bus switch interface IC voltage translation bidirectional translation four-channel multiplexer one-of-four channel selection SCL SDA interrupt input SOIC-20 DW package surface-mount package embedded system industrial sensor interface RoHS REACH
তাৎক্ষণিক বিলওয়াছে রেকোজিউইট
সম্পূর্ণ বিবরণ পূরণ করুন — আমাদের সেলস টিম 24 ঘণ্টার মধ্যে উত্তর দেবে
পার্ট নম্বর উৎপাদক প্যাকেজ QTY লক্ষ্যমূল্য প্রসারিত
✓
বিল প্রস্তুত করা হয়েছে!

আমরা ২৪ ঘণ্টার মধ্যে আপনার ইমেইলে প্রত্যুত্তর দেব

1
RFQ জমা হয়েছে
2
কোটেশন পাওয়া গেছে
3
অর্ডার দেওয়া হয়েছে
4
পেমেন্ট
5
শিপ করা হয়েছে
6
ডেলিভারি হয়েছে
RFQ বিবরণ দেখুন