PCA9544ADW - 4-Channel I2C/SMBus Multiplexer | Texas Instruments
Teilenummer: PCA9544ADW ✓ AktivPCA9544ADW Übersicht
An I2C multiplexer is an interface IC that extends a shared two-wire bus to multiple peripheral branches while preventing signals from inactive branches from affecting the active branch. The PCA9544ADW belongs to the interface-controller hierarchy, connecting a host controller and several sensors, EEPROMs, amplifiers, or other I2C peripherals. Its translating architecture and interrupt inputs support systems in which attached devices require bus isolation or level translation.
The principal functions are four-channel multiplexing, bidirectional voltage translation, and individual downstream interrupt inputs. Four interrupt lines allow a system controller to identify which selected peripheral asserted its interrupt signal. The device also consolidates control of channel selection through the upstream I2C bus, allowing firmware to change the active downstream path without rewiring hardware or mechanically switching buses.
The translating design separates the upstream SCL/SDA pair from the four downstream SCx/SDx pairs. This arrangement provides electrical isolation between the host-side bus and each selected peripheral branch while retaining a compact 20-pin surface-mount implementation. The interrupt structure makes the device especially useful for mixed-signal, embedded, and sensor systems in which several downstream devices may request service from one shared controller.
Typical uses include environmental and industrial sensor nodes, configuration registers accessed through EEPROM, portable measurement equipment, communication modules, and compact control boards that connect more I2C targets than the host bus can address directly. The PCA9544ADW is also appropriate when several embedded subsystems require controlled access to a common peripheral set.
Designers should confirm the upstream and downstream voltage limits, pull-up requirements, channel-selection logic, and interrupt polarity in the manufacturer datasheet before committing a board layout. The SOIC footprint requires adequate lead spacing and process-control measures during assembly. PCB routing should keep SCL and SDA paths short, maintain continuous ground references, and avoid introducing bus-stub capacitance that could impair signal integrity.
This product page combines the manufacturer identification, verified source links, structured technical characteristics, application guidance, and a qualified cross-manufacturer replacement assessment. It also distinguishes confirmed device functions from electrical details that must be established from the complete manufacturer datasheet before layout or production release.
Drop-in-Alternativen für PCA9544ADW – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
PCA9544AD,118
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
PCA9544ADW Technische Daten
| Device Type | I2C/SMBus multiplexer with interrupt and voltage translation |
| Number of Channels | 4 channels |
| Supply Voltage Range | 2.3 V to 5.5 V |
| Upstream Bus | 1 SCL/SDA pair |
| Downstream Buses | 4 SCx/SDx pairs |
| Channel Selection | 1-of-4 selection |
| Interrupt Inputs | 4 inputs |
| Voltage Translation | Bidirectional translating architecture |
| Control Interface | I2C bus |
| Supported Serial Protocol | I2C and SMBus |
| Package Type | SOIC (DW) |
| Anzahl der Pins | 20 pins |
PCA9544ADW soic (dw) Pinbelegungsleitfaden
Pinbelegung für PCA9544ADW (soic (dw)-Gehäuse). Pin-Nummerierung, Funktionen und Anschlussdiagramme sind im Herstellerdatenblatt definiert. Entnehmen Sie diesem den genauen Footprint und Lötrichtlinien.
Keine detaillierten Pinbelegungsdaten verfügbar für PCA9544ADW.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
PCA9544ADW ist geeignet für 6 Anwendungs: Industrial Sensor Hub, Portable Environmental Monitor, EEPROM and Configuration Hub, Communication Module Expansion, Mixed-Signal Audio Interface, Robotics and Control Module.
Industrial Sensor Hub
The PCA9544ADW fits an industrial sensor hub that must connect several I2C sensors to one host controller while preserving a controlled route for each branch. Its four downstream SCx/SDx pairs allow the controller to select one sensor at a time, and the four interrupt inputs provide a mechanism for downstream devices to request attention. The 2.3 V to 5.5 V operating range supports compact embedded systems, while the translating arrangement helps separate host-side and peripheral-side bus levels. Confirm industrial temperature requirements, logic thresholds, pull-up values, and channel isolation limits in the manufacturer datasheet before releasing the PCB.
Portable Environmental Monitor
The PCA9544ADW is useful in a portable environmental monitor that combines temperature, humidity, gas, and motion-related sensing devices on a shared I2C bus. Four selectable downstream branches prevent devices on inactive channels from participating in the current transfer, helping the controller address sensors in a controlled sequence. The 20-pin SOIC package also leaves more board area than a larger package for battery, display, and processing circuitry. Before layout, verify the permitted operating temperature, voltage levels for every sensor, required bus pull-ups, and whether the interrupt lines are sufficient for the chosen sensor set.
EEPROM and Configuration Hub
The PCA9544ADW can organize an embedded control board around several EEPROMs or other configuration peripherals. The host SCL/SDA pair connects to the upstream side, while the four SCx/SDx pairs provide separate downstream routes for individual devices. Because only one channel is selected at a time, firmware can access each configuration target without placing every peripheral permanently on the same electrical branch. The translating architecture adds value when the host and peripheral sides do not share identical logic levels; confirm address behavior, bus capacitance, pull-up placement, and channel-switching timing in the manufacturer datasheet.
Communication Module Expansion
The PCA9544ADW fits a communication module that connects an embedded host to several I2C transceivers, codecs, or configuration blocks. Its one-of-four channel selection allows the controller to isolate downstream branches and address only the active peripheral, which can simplify firmware organization and reduce unwanted bus interactions. The bidirectional translation function is useful when upstream and downstream devices operate at different logic levels. For a production design, verify every branch's voltage range, maximum bus rate, pull-up strategy, interrupt behavior, and whether the module's enclosure or grounding arrangement introduces additional bus-coupling concerns.
Mixed-Signal Audio Interface
The PCA9544ADW can support a mixed-signal audio interface that combines I2C-controlled codecs, amplifiers, and configuration registers. The device's four SCx/SDx branches offer a structured way to isolate peripheral routes, while its interrupt inputs allow a selected audio component to notify the controller. This arrangement is particularly relevant when the host and peripheral sides require different logic levels. Signal-chain performance still depends on the audio devices themselves, so the mux should be placed away from sensitive analog traces and switching nodes. Use short, continuous-ground SCL and SDA routes, then verify channel capacitance and timing against the complete bus specification.
Robotics and Control Module
The PCA9544ADW is appropriate for a compact robotics or automation module that must manage several embedded subsystems over one host bus. Four downstream channels can support sensor controllers, actuator interfaces, or configuration devices, and the interrupt inputs can identify a selected peripheral requesting service. The 20-pin SOIC package supports conventional surface-mount assembly, although lead clearance must be considered in dense robotics electronics. Validate the full operating temperature range, voltage levels, isolation behavior, and interrupt polarity for each attached subsystem. Mechanical vibration and temperature changes should also be evaluated at the system level rather than inferred from the mux specifications alone.
Technische Referenzdaten für PCA9544ADW – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | PCA9544AD,118 |
|---|---|---|
| Manufacturer | Texas Instruments | NXP Semiconductors |
| Package | SOIC-20 (DW) | SOIC-20 |
| Multiplexer Channels | 4 | 4 |
| Supported Buses | I2C and SMBus | I2C |
| Voltage Translation | Bidirectional translating architecture | Bidirectional translation |
| Interrupt Inputs | 4 | 4 |
| Upstream Bus | 1 SCL/SDA pair | 1 SCL/SDA pair |
| Downstream Buses | 4 SCx/SDx pairs | 4 SCx/SDx pairs |
Wichtigste Unterscheidungsmerkmale
- Four individually interruptable downstream branches (vs. PCA9544AD,118)
- Bidirectional level translation in the same multiplexer function (vs. PCA9544AD,118)
- Defined 2.3 V to 5.5 V device operating range (vs. PCA9544AD,118)
Designhinweise
Route the upstream SCL/SDA pair and all four downstream SCx/SDx branches as short, continuous traces with a nearby ground reference. Place each branch's required pull-up network at the appropriate end of that branch, and avoid long stubs or test-point loops that add excessive capacitance. Confirm pull-up voltage and resistance against the logic level and bus-rate requirements in the manufacturer datasheet.
Do not assume that all downstream peripherals can be addressed simultaneously. The PCA9544ADW selects one downstream channel at a time, so firmware should complete or suspend a transfer before changing channels. Also avoid assuming that the operating supply range establishes every allowed upstream or downstream voltage; verify the separate logic-level ranges in the complete manufacturer datasheet.
Treat SCL, SDA, SCx, and SDx as paired communication nets with controlled return paths. Keep the multiplexer away from switching regulators, inductors, and high-current power traces where practical. Account for connector and test-point capacitance, and use the datasheet timing and capacitance limits when extending any downstream branch beyond the recommended PCB topology.
The 20-pin SOIC package is straightforward for conventional reflow assembly but requires adequate spacing from tall components and board edges. Maintain the manufacturer's land pattern and solder recommendations, inspect the pin-one orientation during assembly, and keep the interrupt traces away from noisy analog or switching nodes because an unintended edge on these inputs could create a false service request.
Compliance-Informationen
The verified manufacturer and distributor listings do not provide explicit compliance declarations for this exact orderable part. AEC-Q100 is not applicable because this device is not an automotive-qualified component in the cited information.