PCA9617ADP - Fm+ I2C Level Shifter | NXP Semiconductors
MPN: PCA9617ADP ✓ সক্রিয়PCA9617ADP সারাংশ
A level-translating I2C repeater is an interface IC that converts signal voltage levels between two communication domains and isolates them electrically through buffering. It is used when a low-voltage sensor, microcontroller, or peripheral must communicate with a higher-voltage I2C bus. The PCA9617A family belongs to the broader I2C interface IC and signal-buffer hierarchy, where repeated or extended bus sections require buffering to maintain signal integrity and support longer interconnect distances.
The PCA9617ADP supports low-side and high-side voltage domains from 0.8 V to 5.5 V and 2.2 V to 5.5 V respectively. Its Fm+ support enables operation with I2C-compatible devices that use the higher Fast-mode Plus signaling rate. Bidirectional SDA and SCL buffering allows the device to be inserted directly into an I2C bus segment without changing the bus transaction sequence. The 8-pin TSSOP package supports compact PCB layouts in industrial, consumer, and embedded systems.
The NXP datasheet identifies the PCA9617A as a CMOS integrated circuit for level shifting between low-voltage and higher-voltage I2C or SMBus applications. The buffered design helps prevent low-voltage bus nodes from being exposed to incompatible high-side voltage levels. Because the device is a bus repeater rather than a general-purpose logic buffer, it preserves the electrical behavior expected by bidirectional open-drain I2C signaling and provides a defined interface between voltage domains.
Typical uses include voltage-level adaptation between 1.8 V or 2.5 V microcontrollers and 3.3 V or 5 V peripherals, isolating sensor segments on a shared I2C bus, extending a bus section through a repeater, and supporting mixed-voltage embedded systems. It is particularly useful when the low-side and high-side devices use different supply rails but still require common I2C addressing and pull-up arrangements.
When laying out the circuit, verify that pull-up resistors are connected to the correct supply rail for each voltage domain and that the repeater is placed according to the datasheet's recommended bus topology. Keep the SDA and SCL traces short and route them away from noisy switching nodes. The TSSOP footprint also requires attention to solder-joint inspection because its lead pitch is finer than a conventional SOIC-8 footprint.
This product page combines the NXP product description, datasheet references, packaging information, application guidance, and drop-in candidate analysis to support component selection and PCB implementation. Request a quote for current commercial availability, lead time, and procurement requirements using the Request a Quote form on this page.
এর জন্য ড্রপ-ইন বিকল্প PCA9617ADP — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।
এই সিরিজের ভ্যারিয়েন্ট
একই সিরিজের মডেল যেগুলো drop-in compatible PCA9617ADP (একই form factor এবং footprint) — পার্থক্য রয়েছে Package, Number of Channels, Mounting Type, Function, Maximum Operating Frequency.
PCA9617ADPJ
✅ ড্রপ-ইনমূল্যের জন্য যোগাযোগ করুন
ডেটাশিট দেখুন →PCA9617ADP বিশেষণ
| Device Type | CMOS level-translating I2C-bus repeater |
| I2C Mode Support | Fast-mode Plus (Fm+) and SMBus |
| Low-Side Voltage Range | 0.8 V to 5.5 V |
| High-Side Voltage Range | 2.2 V to 5.5 V |
| Bus Signals | Bidirectional SDA and SCL |
| Logic Family | CMOS |
| Number of Channels | 2 bidirectional I2C bus signals |
| প্যাকেজ | 8-pin TSSOP |
| মাউন্টিং টাইপ | Surface mount |
PCA9617ADP 8-pin tssop পিন কনফিগারেশন গাইড
PCA9617ADP (8-pin tssop প্যাকেজ)-এর পিন কনফিগারেশন। পিন নম্বরিং, ফাংশন এবং সংযোগ ডায়াগ্রাম প্রস্তুতকারকের ডেটাশিটে সংজ্ঞায়িত করা আছে। সঠিক ফুটপ্রিন্ট এবং সোল্ডারিং নির্দেশিকার জন্য এটি দেখুন।
এর জন্য বিস্তারিত পিনআউট ডেটা পাওয়া যায়নি PCA9617ADP.
দেখুন ডেটাশিট সম্পূর্ণ পিন কনফিগারেশনের জন্য।
সাধারণ ব্যবহার
PCA9617ADP এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Mixed-Voltage Microcontroller Interfaces, Low-Voltage Sensor Bus Isolation, Industrial I2C Segment Extension, Consumer Embedded Peripherals, Fast-Mode Plus Bus Interfacing, Level-Shifted Communication Ports.
Mixed-Voltage Microcontroller Interfaces
The PCA9617ADP fits a boundary between low-voltage digital logic and higher-voltage I2C peripherals because it translates low-side signals across 0.8 V to 5.5 V and high-side signals across 2.2 V to 5.5 V. Place it between the controller's SDA and SCL pins and the external bus, with pull-up resistors connected to the appropriate rail on each side. Bidirectional buffering allows the controller to retain I2C read and write transactions while the two domains use different logic levels.
সুপারিশকৃত
Low-Voltage Sensor Bus Isolation
The PCA9617ADP can isolate a group of 0.8 V to 5.5 V sensors from a 2.2 V to 5.5 V system bus. Its buffered SDA and SCL paths keep the two voltage domains separated while preserving bidirectional communication needed for sensor addressing and register access. Select pull-up values for each rail and confirm that the sensor's thresholds and the controller's high-level voltage remain within the translated ranges before releasing the design.
সুপারিশকৃত
Industrial I2C Segment Extension
The PCA9617ADP is useful when an industrial controller must connect to an I2C segment operating at a higher voltage than its local logic. The level translator supports Fast-mode Plus I2C and SMBus applications while buffering both SDA and SCL signals in the 8-pin TSSOP package. Place the repeater at the voltage-domain boundary and verify the pull-up rails, maximum bus capacitance, timing margin, and grounding arrangement for the complete segment.
সুপারিশকৃত
Consumer Embedded Peripherals
The PCA9617ADP supports compact consumer embedded designs where a low-voltage controller communicates with higher-voltage EEPROMs, sensors, or display peripherals over I2C. Its bidirectional level translation avoids forcing the controller I/O pins to tolerate the higher-side voltage. The TSSOP-8 footprint conserves board area, although the design must provide correct pull-ups on each side and account for the shorter lead pitch during soldering and inspection.
সুপারিশকৃত
Fast-Mode Plus Bus Interfacing
The PCA9617ADP fits Fm+ I2C interfaces that require voltage translation between two domains while retaining high-speed bidirectional bus behavior. The NXP PCA9617A datasheet identifies Fast-mode Plus and SMBus support as key applications. Engineers should review the timing characteristics, bus-capacitance limits, pull-up resistance, and trace length using the manufacturer's recommended circuit rather than treating the repeater as a generic logic buffer.
সুপারিশকৃত
Level-Shifted Communication Ports
The PCA9617ADP can provide a defined voltage boundary between communication ports whose SDA and SCL logic levels differ. Bidirectional buffering supports both controller-driven commands and slave-returned data without unidirectional direction control. The design should use separate pull-up networks for the low and high sides, maintain common ground, and keep sensitive translator pins away from high-current switching paths to avoid introducing bus errors through supply or signal disturbance.
সুপারিশকৃত
এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা PCA9617ADP — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।
নির্বাচন গাইড
বিকল্পের সাথে তুলনা
| পারামিটার | এই পণ্য | PCA9617ADPJ |
|---|---|---|
| Package | TSSOP-8 | TSSOP-8 - same |
| Brand | NXP Semiconductors | NXP Semiconductors |
| Device Function | Level-translating I2C-bus repeater | Level-translating I2C-bus repeater |
| Low-Side Voltage Range | 0.8 V to 5.5 V | 0.8 V to 5.5 V |
| High-Side Voltage Range | 2.2 V to 5.5 V | 2.2 V to 5.5 V |
| I2C Support | Fast-mode Plus and SMBus | Fast-mode Plus and SMBus |
| Buffered Signals | Bidirectional SDA and SCL | Bidirectional SDA and SCL |
| Logic Technology | CMOS | CMOS |
| Lifecycle Status | Active | Active |
মূল পার্থক্যসমূহ
- Direct same-package sourcing path (বনামPCA9617ADPJ)
- Fm+ and SMBus support (বনামPCA9617ADPJ)
- Bidirectional two-signal buffering (বনামPCA9617ADPJ)
ডিজাইন নোট
Place the PCA9617ADP directly at the boundary between the two I2C voltage domains. Keep SDA and SCL routing short and continuous, connect each pull-up resistor to the supply associated with its own bus side, and provide a common ground between the translator and attached devices. Avoid routing the high-voltage-side traces beneath the low-voltage-side circuitry where switching currents could couple into the sensitive bus nodes.
Do not treat PCA9617ADP as a one-way logic-buffer pair. Both SDA and SCL paths are bidirectional, and pull-up networks must exist on the correct side of the repeater for the I2C open-drain signaling to operate properly. Check the NXP datasheet for enable requirements and pin assignments before finalizing the schematic, especially when a bus section may be disconnected or held in a reset state.
Use the manufacturer-recommended TSSOP-8 footprint and account for its fine lead pitch during paste printing, reflow profiling, and post-reflow inspection. Maintain adequate solder mask dam spacing and avoid accidental solder bridges between adjacent SDA, SCL, supply, and ground pins. Confirm land geometry against the latest NXP package drawing rather than scaling a generic TSSOP footprint.
কমপ্লায়েন্স তথ্য
The NXP product page and datasheet identify the PCA9617ADP as an active component, but no explicit compliance declarations are included in the listed product information. AEC-Q100 is not applicable to this general-purpose interface IC.