PI7C9X1170BCLEX - 33Mbps I2C/SPI to UART Bridge | Diodes Inc
MPN: PI7C9X1170BCLEX ✓ সক্রিয়PI7C9X1170BCLEX সারাংশ
An I2C/SPI-to-UART bridge is an interface IC that translates commands and data between a clock-based serial bus and a UART peripheral. It belongs to the hierarchy of serial interface controllers, communication controllers, interface ICs, and semiconductors. This conversion allows a host using I2C or SPI to communicate with equipment that exposes only a UART channel without requiring a discrete protocol converter or an FPGA-based interface.
The PI7C9X1170BCLEX provides one UART channel, supports data rates up to 33Mbps, and includes as many as eight configurable GPIO pins. Its 16-pin TSSOP package supports compact surface-mount PCB construction. The low operating and sleeping current claims make the controller suitable for systems where the bridge must remain available without causing excessive standby load. The manufacturer datasheet also describes the same controller family in TSSOP-16 and TSSOP-24 packages, while this orderable configuration is the 16-pin version.
The bridge architecture places an I2C or SPI control interface on the host side and a single high-performance UART channel on the peripheral side. Programmable GPIO pins can expose discrete control, status, interrupt, or general digital signals around the bridge. Because the UART side operates at speeds up to 33Mbps, the device can serve high-throughput embedded links rather than only slow human-interface ports. Exact electrical limits, voltage levels, timing values, and configuration details should be taken from the manufacturer datasheet before finalizing a design.
Typical uses include industrial control modules, instrumentation, embedded test equipment, peripheral adapters, and compact consumer or communications products. A host microcontroller may configure the UART and GPIO functions over I2C or SPI, while the bridge presents the resulting data through a standard asynchronous serial channel. The package size is particularly useful when the design already uses a TSSOP-16 footprint and needs interface conversion without adding another large package.
When laying out a board, place the device close to the connector or transceiver associated with the UART channel and keep clock-capable I2C or SPI traces short. Confirm voltage compatibility, pull-up requirements, UART levels, and pin multiplexing in the manufacturer datasheet. Treat the PI7C9X1170BCLEX as a bridge rather than a complete UART transceiver, so the downstream UART interface may require a separate line driver or receiver.
This page consolidates the verified 33Mbps performance, 16-pin packaging, available GPIO count, interface functions, and drop-in-family references into an engineering-focused overview. It also distinguishes confirmed device facts from parameters that must be checked in the datasheet, helping designers evaluate the PI7C9X1170BCLEX before schematic capture or PCB release.
এর জন্য ড্রপ-ইন বিকল্প PI7C9X1170BCLEX — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।
PI7C9X1170BCLE
✅ ড্রপ-ইন📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
PI7C9X1170BBLEX
✅ ড্রপ-ইনমূল্যের জন্য যোগাযোগ করুন
ডেটাশিট দেখুন →PI7C9X1170BCLEX সর্বোচ্চ রেটিং ও বৈদ্যুতিক বৈশিষ্ট্য
| Product Type | I2C/SPI to single-channel UART bridge controller |
| Maximum Data Rate | 33Mbps |
| UART Channel Count | 1 channel |
| Host Interfaces | I2C and SPI |
| Programmable GPIO Count | Up to 8 pins |
| প্যাকেজ | 16-pin TSSOP |
| Package Family | TSSOP surface-mount package family |
| মাউন্টিং টাইপ | Surface mount |
| Temperature Grade | Industrial |
PI7C9X1170BCLEX tssop surface-mount package family পিন কনফিগারেশন গাইড
PI7C9X1170BCLEX (tssop surface-mount package family প্যাকেজ)-এর পিন কনফিগারেশন। এই পাওয়ার ডিভাইসে গেট, ড্রেন ও সোর্স টার্মিনাল রয়েছে। নন-পোলারাইজড প্যাকেজের ক্ষেত্রে সঠিক পিন 1 ওরিয়েন্টেশন ও ফুটপ্রিন্ট বিবরণের জন্য প্রস্তুতকারকের ডেটাশিট দেখুন। সাধারণ অ্যাপ্লিকেশনগুলির মধ্যে রয়েছে পাওয়ার সাপ্লাই ডিজাইন, মোটর ড্রাইভিং এবং লোড সুইচিং।
এর জন্য বিস্তারিত পিনআউট ডেটা পাওয়া যায়নি PI7C9X1170BCLEX.
দেখুন ডেটাশিট সম্পূর্ণ পিন কনফিগারেশনের জন্য।
সাধারণ ব্যবহার
PI7C9X1170BCLEX এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Industrial Control Module, Embedded Test and Measurement Equipment, Instrumentation Data Acquisition, Peripheral Adapter, Low-Power Embedded System, Communications and Network Equipment.
Industrial Control Module
The PI7C9X1170BCLEX fits industrial control modules that need a compact bridge between a host controller and a UART peripheral. A supervisory processor can access or configure the peripheral through I2C or SPI while the bridge presents the data on a UART channel capable of rates up to 33Mbps. Its 16-pin TSSOP package limits board area, and up to eight programmable GPIO pins can carry discrete status or control signals. The principal design check is compatibility with the industrial system's supply voltage and signal levels, because the controller is not a complete UART line transceiver.
সুপারিশকৃত
Embedded Test and Measurement Equipment
The PI7C9X1170BCLEX can connect a test instrument's I2C- or SPI-based control processor to a high-speed UART instrument. The bridge's 33Mbps maximum UART data rate supports faster serial transfer than a basic asynchronous peripheral interface, while the programmable GPIO resources can expose trigger, status, or alarm signals. Its TSSOP-16 package is useful when instrument boards contain several bridge and conditioning functions but have limited routing area. Firmware must configure the correct UART rate, data format, and GPIO function through the manufacturer's register description.
সুপারিশকৃত
Instrumentation Data Acquisition
The PI7C9X1170BCLEX is suitable for instrumentation systems in which sensors or data-acquisition modules expose UART data but the main processor communicates through I2C or SPI. Using the bridge allows the host to manage the peripheral through a clocked bus while retaining an asynchronous UART path up to 33Mbps. Up to eight programmable GPIO pins can provide acquisition triggers, readiness indicators, or configuration controls without consuming additional host GPIO resources. Because it operates at the logic level rather than directly driving long cables, the design may also require an appropriate UART transceiver for external connection.
সুপারিশকৃত
Peripheral Adapter
PI7C9X1170BCLEX fits compact adapters that add a UART interface to an embedded platform using I2C or SPI. A system-on-chip can configure baud rate, data framing, and available GPIO behavior through the bridge instead of implementing the UART channel directly in host firmware. The 16-pin TSSOP package supports PCB reuse when a design already contains that footprint. At the connector side, use a suitable UART transceiver when the target interface requires RS-232, RS-422, or RS-485 electrical levels rather than direct logic signaling.
সুপারিশকৃত
Low-Power Embedded System
The PI7C9X1170BCLEX can support low-power embedded systems where a compact logic-level UART path must coexist with an I2C or SPI host bus. The manufacturer datasheet highlights low operating and sleeping current characteristics, allowing the bridge to remain part of a compact platform without an unnecessarily large interface package. Programmable GPIO outputs can also assist with peripheral enable, status, or wake-related functions when configured appropriately. Exact sleep-mode behavior and current limits must be checked in the datasheet because no numeric operating or sleeping current values are stated in the product summary.
সুপারিশকৃত
Communications and Network Equipment
The PI7C9X1170BCLEX can provide protocol bridging in communications equipment where a management processor uses I2C or SPI to access a UART-based module. The single UART channel supports data rates up to 33Mbps, making it applicable to embedded links that transfer more data than a slow human-interface port. Eight programmable GPIO pins expand the number of discrete module-control functions available to the host. The bridge remains a logic-level IC, so long-distance or non-TTL interfaces require an appropriate external line driver and receiver selected for the target electrical standard.
সুপারিশকৃত
এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা PI7C9X1170BCLEX — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।
নির্বাচন গাইড
বিকল্পের সাথে তুলনা
| পারামিটার | এই পণ্য | PI7C9X1170BCLE | PI7C9X1170BBLEX |
|---|---|---|---|
| Brand | Diodes Incorporated | Diodes Incorporated | Diodes Incorporated |
| Package | TSSOP-16 | TSSOP-16 | TSSOP-16 |
| Product Type | I2C/SPI to single-channel UART bridge controller | I2C/SPI to single-channel UART bridge controller | I2C/SPI to UART bridge controller |
| Host Interfaces | I2C and SPI | I2C and SPI | I2C and SPI |
মূল পার্থক্যসমূহ
- Combines three embedded interface functions in one controller (বনামPI7C9X1170BCLE)
- Supports high-speed UART communication (বনামPI7C9X1170BBLEX)
- Adds programmable digital I/O without expanding the package (বনামPI7C9X1170BCLE)
ডিজাইন নোট
Place the PI7C9X1170BCLEX close to the device whose I2C, SPI, UART, and GPIO signals it bridges, and route the clock-capable I2C or SPI traces away from high-current switching nodes. Maintain continuous ground return paths under the TSSOP-16 footprint and place required pull-up or bypass components directly at their associated pins. The listing does not specify pin names or required component values, so use the manufacturer pin-description and application guidance for the final schematic.
Treat the bridge as a logic-level UART interface and verify whether the destination connector requires RS-232, RS-422, RS-485, or direct TTL signaling. Add the appropriate external UART transceiver when voltage conversion, isolation direction, or long-distance noise rejection is required. Keep the UART trace away from clocks and power-converter switching edges, and ground the external transceiver return path properly to prevent data corruption.
Do not approve a replacement based on the TSSOP-16 footprint alone. For PI7C9X1170BCLE and PI7C9X1170BBLEX, confirm the exact ordering suffix, device revision, exposed functions, supply limits, timing, and marking against the manufacturer datasheet. The target supports up to eight programmable GPIO pins, but alternate parts must provide the required pin functions. Also verify that the host firmware can configure the selected variant's baud-rate and data-format behavior.
Decouple the bridge close to its supply pins using the capacitance and placement specified in the manufacturer datasheet. Because the family is described as having low operating and sleeping current, check the actual mode currents at the system supply voltage before treating the controller as negligible in a power budget. Confirm that every I2C, SPI, UART, and GPIO signal remains within the device's input and output limits.
কমপ্লায়েন্স তথ্য
The component is identified as an industrial-grade interface IC, but no specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals declarations are stated in the available product information.