Diodes Incorporated

PI7C9X1170BCLEX - 33Mbps I2C/SPI to UART Bridge | Diodes Inc

MPN: PI7C9X1170BCLEX ✓ Aktif
16-pin TSSOP Package
MOQ: 1 |

PI7C9X1170BCLEX Genel Bakış

The Diodes Incorporated PI7C9X1170BCLEX is a single-channel I2C-bus/SPI-to-UART bridge controller with a maximum data rate of 33Mbps, eight programmable general-purpose I/O pins, and a 16-pin TSSOP package. The device bridges serial host interfaces with an asynchronous UART channel while providing low operating and sleeping current characteristics.

An I2C/SPI-to-UART bridge is an interface IC that translates commands and data between a clock-based serial bus and a UART peripheral. It belongs to the hierarchy of serial interface controllers, communication controllers, interface ICs, and semiconductors. This conversion allows a host using I2C or SPI to communicate with equipment that exposes only a UART channel without requiring a discrete protocol converter or an FPGA-based interface.

The PI7C9X1170BCLEX provides one UART channel, supports data rates up to 33Mbps, and includes as many as eight configurable GPIO pins. Its 16-pin TSSOP package supports compact surface-mount PCB construction. The low operating and sleeping current claims make the controller suitable for systems where the bridge must remain available without causing excessive standby load. The manufacturer datasheet also describes the same controller family in TSSOP-16 and TSSOP-24 packages, while this orderable configuration is the 16-pin version.

The bridge architecture places an I2C or SPI control interface on the host side and a single high-performance UART channel on the peripheral side. Programmable GPIO pins can expose discrete control, status, interrupt, or general digital signals around the bridge. Because the UART side operates at speeds up to 33Mbps, the device can serve high-throughput embedded links rather than only slow human-interface ports. Exact electrical limits, voltage levels, timing values, and configuration details should be taken from the manufacturer datasheet before finalizing a design.

Typical uses include industrial control modules, instrumentation, embedded test equipment, peripheral adapters, and compact consumer or communications products. A host microcontroller may configure the UART and GPIO functions over I2C or SPI, while the bridge presents the resulting data through a standard asynchronous serial channel. The package size is particularly useful when the design already uses a TSSOP-16 footprint and needs interface conversion without adding another large package.

When laying out a board, place the device close to the connector or transceiver associated with the UART channel and keep clock-capable I2C or SPI traces short. Confirm voltage compatibility, pull-up requirements, UART levels, and pin multiplexing in the manufacturer datasheet. Treat the PI7C9X1170BCLEX as a bridge rather than a complete UART transceiver, so the downstream UART interface may require a separate line driver or receiver.

This page consolidates the verified 33Mbps performance, 16-pin packaging, available GPIO count, interface functions, and drop-in-family references into an engineering-focused overview. It also distinguishes confirmed device facts from parameters that must be checked in the datasheet, helping designers evaluate the PI7C9X1170BCLEX before schematic capture or PCB release.

Drop-in alternatifler için PI7C9X1170BCLEX — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.

PI7C9X1170BCLE

✅ Yerleştirme
📦 TSSOP-16
Same PI7C9X1170 controller family and 16-pin TSSOP package; the ordering suffix differs, with no verified quantitative electrical difference available.

📋 Katalogda Olmayan Referans Alternatifi

PI7C9X1170BBLEX

✅ Yerleştirme
Diodes Incorporated
📦 TSSOP-16
I2C-bus/SPI to single-channel UART bridge controller · 33 Mbps · I2C-bus and SPI · 1 channel · Up to 8 pins · 16-pin TSSOP · 16 terminals · Rectangular

Fiyat için iletişime geçin

Veri Şablonunu Görüntüle →

PI7C9X1170BCLEX Maksimum Değerlendirmeler & Elektriksel Özellikler

Product Type I2C/SPI to single-channel UART bridge controller
Maximum Data Rate 33Mbps
UART Channel Count 1 channel
Host Interfaces I2C and SPI
Programmable GPIO Count Up to 8 pins
Paket 16-pin TSSOP
Package Family TSSOP surface-mount package family
Montaj Türü Surface mount
Temperature Grade Industrial

PI7C9X1170BCLEX tssop surface-mount package family Pin Yapısı Kılavuzu

PI7C9X1170BCLEX (tssop surface-mount package family paket) için pin yapısı. Bu güç cihazı gate, drain ve kaynak terminal özelliklerlidir. Polarizasyonlu paketler için, doğru pin 1 yönlendirme ve ayak detayları için üretici veri kitapçığını referans alın. Orta uygulamalar arasında güç besleme tasarımı, motor kontrolü ve yük değiştirme bulunur.

tssop surface-mount package family paket pin çizelgesi için PI7C9X1170BCLEX

Ayrıntılı pin çıkış verisi mevcut değil: PI7C9X1170BCLEX.

Aşağıdaki veri sayfası tam pin konfigürasyonu için.

Tipik Uygulamalar

PI7C9X1170BCLEX için uygundur 6 uygulamas: Industrial Control Module, Embedded Test and Measurement Equipment, Instrumentation Data Acquisition, Peripheral Adapter, Low-Power Embedded System, Communications and Network Equipment.

🏭

Industrial Control Module

The PI7C9X1170BCLEX fits industrial control modules that need a compact bridge between a host controller and a UART peripheral. A supervisory processor can access or configure the peripheral through I2C or SPI while the bridge presents the data on a UART channel capable of rates up to 33Mbps. Its 16-pin TSSOP package limits board area, and up to eight programmable GPIO pins can carry discrete status or control signals. The principal design check is compatibility with the industrial system's supply voltage and signal levels, because the controller is not a complete UART line transceiver.

🔧

Embedded Test and Measurement Equipment

The PI7C9X1170BCLEX can connect a test instrument's I2C- or SPI-based control processor to a high-speed UART instrument. The bridge's 33Mbps maximum UART data rate supports faster serial transfer than a basic asynchronous peripheral interface, while the programmable GPIO resources can expose trigger, status, or alarm signals. Its TSSOP-16 package is useful when instrument boards contain several bridge and conditioning functions but have limited routing area. Firmware must configure the correct UART rate, data format, and GPIO function through the manufacturer's register description.

📡

Instrumentation Data Acquisition

The PI7C9X1170BCLEX is suitable for instrumentation systems in which sensors or data-acquisition modules expose UART data but the main processor communicates through I2C or SPI. Using the bridge allows the host to manage the peripheral through a clocked bus while retaining an asynchronous UART path up to 33Mbps. Up to eight programmable GPIO pins can provide acquisition triggers, readiness indicators, or configuration controls without consuming additional host GPIO resources. Because it operates at the logic level rather than directly driving long cables, the design may also require an appropriate UART transceiver for external connection.

🔌

Peripheral Adapter

PI7C9X1170BCLEX fits compact adapters that add a UART interface to an embedded platform using I2C or SPI. A system-on-chip can configure baud rate, data framing, and available GPIO behavior through the bridge instead of implementing the UART channel directly in host firmware. The 16-pin TSSOP package supports PCB reuse when a design already contains that footprint. At the connector side, use a suitable UART transceiver when the target interface requires RS-232, RS-422, or RS-485 electrical levels rather than direct logic signaling.

🔋

Low-Power Embedded System

The PI7C9X1170BCLEX can support low-power embedded systems where a compact logic-level UART path must coexist with an I2C or SPI host bus. The manufacturer datasheet highlights low operating and sleeping current characteristics, allowing the bridge to remain part of a compact platform without an unnecessarily large interface package. Programmable GPIO outputs can also assist with peripheral enable, status, or wake-related functions when configured appropriately. Exact sleep-mode behavior and current limits must be checked in the datasheet because no numeric operating or sleeping current values are stated in the product summary.

🌐

Communications and Network Equipment

The PI7C9X1170BCLEX can provide protocol bridging in communications equipment where a management processor uses I2C or SPI to access a UART-based module. The single UART channel supports data rates up to 33Mbps, making it applicable to embedded links that transfer more data than a slow human-interface port. Eight programmable GPIO pins expand the number of discrete module-control functions available to the host. The bridge remains a logic-level IC, so long-distance or non-TTL interfaces require an appropriate external line driver and receiver selected for the target electrical standard.

What is the PI7C9X1170BCLEX?
The PI7C9X1170BCLEX is a single-channel I2C-bus/SPI-to-UART bridge controller from Diodes Incorporated. According to the manufacturer datasheet, it supports serial data rates up to 33Mbps and provides up to eight programmable GPIO pins in a 16-pin TSSOP package. It is intended for embedded systems that need a host processor to configure or access a UART peripheral through an I2C or SPI interface.
What are the key specifications of PI7C9X1170BCLEX that engineers should know?
The PI7C9X1170BCLEX combines one UART channel, I2C and SPI host interfaces, up to eight programmable GPIO pins, and a maximum 33Mbps data rate. The device is offered in a 16-pin TSSOP package and is classified as an industrial-grade part. The manufacturer datasheet also states that the controller family is designed for low operating and sleeping current.
How does the PI7C9X1170BCLEX bridge I2C and SPI to UART?
The PI7C9X1170BCLEX accepts host-side commands and data through I2C or SPI and translates the required communication into a single UART channel. According to the manufacturer datasheet, the UART path supports data rates up to 33Mbps. The bridge can also present up to eight programmable GPIO functions, allowing digital status or control signals to be handled alongside the serial data.
Where can I download the PI7C9X1170BCLEX datasheet PDF?
The PI7C9X1170BCLEX datasheet PDF is available from the manufacturer-document link shown on this page. It describes the I2C-bus/SPI-to-UART architecture, the 33Mbps maximum data rate, low-current operation, up to eight GPIO pins, and the controller family's TSSOP-16 and TSSOP-24 package options. Use the pin-description and electrical-characteristics sections when assigning connections and voltage levels.
Where can I find the PI7C9X1170BCLEX pinout?
The PI7C9X1170BCLEX uses a 16-pin TSSOP package, and its pin assignments are identified in the manufacturer datasheet. The pin-description table should be used to map power, ground, I2C or SPI, UART, and GPIO functions to the package pins. Because the complete pin map is not reproduced in the product listing, assign PCB nets from the datasheet rather than inferring pin names from neighboring functions.
Is PI7C9X1170BCLEX suitable for industrial control systems?
The PI7C9X1170BCLEX is identified as an industrial-temperature-grade interface controller and is marketed for embedded bridge applications. Its I2C/SPI host interface, UART channel up to 33Mbps, and programmable GPIO resources suit industrial control, instrumentation, and peripheral-adapter designs. The exact operating-temperature limits, supply range, and electrical characteristics must be confirmed in the manufacturer datasheet.
What is the difference between PI7C9X1170BCLEX and PI7C9X1170BCLE?
PI7C9X1170BCLEX and PI7C9X1170BCLE are both identified as 16-pin TSSOP versions of the PI7C9X1170 I2C/SPI-to-UART bridge controller. The available listing information establishes the same controller family and package form, while the orderable suffix distinguishes the listed variant. Verify device revision, marking, temperature grade, and tape-and-reel order code against the manufacturer ordering information before releasing a replacement.
Is PI7C9X1170BCLEX the same as PI7C9X1170BBLEX?
PI7C9X1170BCLEX and PI7C9X1170BBLEX belong to the same PI7C9X1170 controller family and are listed in 16-pin TSSOP packages. They are close same-brand drop-in candidates, but the suffix difference may represent a device or ordering-option change. Confirm the datasheet revision, exposed functions, configuration registers, operating limits, and package markings before treating PI7C9X1170BBLEX as an unqualified replacement.
What is the best drop-in replacement for PI7C9X1170BCLEX?
PI7C9X1170BCLE is the closest verified drop-in candidate because it is listed in the same 16-pin TSSOP package and uses the same PI7C9X1170 I2C/SPI-to-UART controller designation. PI7C9X1170BBLEX is another same-family possibility, but its exact suffix differences require datasheet review. A replacement should not be approved solely from package matching; confirm pin functions, timing, voltage levels, and revision status.
When should I choose PI7C9X1170BCLEX over PI7C9X1170BCLE?
Choose PI7C9X1170BCLEX when the exact manufacturer order code, marking, qualification details, and tape-and-reel configuration match the approved bill of materials. PI7C9X1170BCLE remains appropriate when its device revision and ordering information satisfy the design. Both provide the same 16-pin TSSOP PI7C9X1170 bridge family, so the deciding factors are controlled part-number details rather than basic bridge functionality.
Can PI7C9X1170BCLEX replace a discrete I2C-to-UART interface circuit?
The PI7C9X1170BCLEX can consolidate an I2C- or SPI-based host interface and one UART channel into a single 16-pin TSSOP device while adding up to eight programmable GPIO pins. It can simplify a discrete bridge implementation when the required protocol, timing, and voltage specifications match. It does not replace the external line driver or receiver when the target UART requires a separate transceiver.
Where can I buy PI7C9X1170BCLEX online?
Use the Request a Quote form on this page to request PI7C9X1170BCLEX availability, order quantity, lead time, and a current quotation. The verified product listings confirm the part as a 16-pin TSSOP tape-and-reel device, but live stock and commercial terms can change. State the required quantity and whether reels, cut tape, or another approved packing method is needed in the request.
What is the price of PI7C9X1170BCLEX?
A current price for PI7C9X1170BCLEX is available through the Request a Quote form on this page. The product page maintains the latest commercial response without embedding a potentially stale price into technical content. Submit the required order quantity and packing preference so the quote can reflect the correct PI7C9X1170BCLEX configuration and delivery requirements.
What is the lead time for PI7C9X1170BCLEX?
The current lead time for PI7C9X1170BCLEX should be requested through the Request a Quote form on this page. Lead time can depend on order quantity, package form, and current factory and distribution availability. Identify the required reel quantity and any production schedule in the request so the commercial response can reflect the actual manufacturing need.
Is PI7C9X1170BCLEX in stock?
PI7C9X1170BCLEX availability should be confirmed through the Request a Quote form on this page. The part is offered in a 16-pin TSSOP tape-and-reel configuration, and the listing result identifies it as an in-stock component, but inventory changes continuously. Request the desired quantity and delivery date to obtain the current availability commitment.

Mühendislik referans verileri: PI7C9X1170BCLEX — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.

Seçim Kılavuzu

Choose PI7C9X1170BCLEX when the design needs a compact, single-channel I2C/SPI-to-UART bridge capable of operating at up to 33Mbps and requires programmable GPIO functions. PI7C9X1170BCLE is the closest same-family alternative when its exact ordering code and qualification details satisfy the design; its TSSOP-16 package permits footprint reuse. PI7C9X1170BBLEX may be considered when its suffix-specific device definition is confirmed compatible with the target's pin functions, timing, supply limits, and firmware configuration. In every case, verify the manufacturer datasheet, because package matching alone does not establish drop-in compatibility. A separate UART transceiver is also needed when the destination uses RS-232, RS-422, or RS-485 electrical levels rather than logic-level signaling.

Alternatiflerle Karşılaştırma

Parametre Bu Ürün PI7C9X1170BCLE PI7C9X1170BBLEX
Brand Diodes Incorporated Diodes Incorporated Diodes Incorporated
Package TSSOP-16 TSSOP-16 TSSOP-16
Product Type I2C/SPI to single-channel UART bridge controller I2C/SPI to single-channel UART bridge controller I2C/SPI to UART bridge controller
Host Interfaces I2C and SPI I2C and SPI I2C and SPI

Ana Farklılayıcılar

  • Combines three embedded interface functions in one controller (karşılaştırma:PI7C9X1170BCLE)
  • Supports high-speed UART communication (karşılaştırma:PI7C9X1170BBLEX)
  • Adds programmable digital I/O without expanding the package (karşılaştırma:PI7C9X1170BCLE)

Tasarım Notları

Place the PI7C9X1170BCLEX close to the device whose I2C, SPI, UART, and GPIO signals it bridges, and route the clock-capable I2C or SPI traces away from high-current switching nodes. Maintain continuous ground return paths under the TSSOP-16 footprint and place required pull-up or bypass components directly at their associated pins. The listing does not specify pin names or required component values, so use the manufacturer pin-description and application guidance for the final schematic.

Treat the bridge as a logic-level UART interface and verify whether the destination connector requires RS-232, RS-422, RS-485, or direct TTL signaling. Add the appropriate external UART transceiver when voltage conversion, isolation direction, or long-distance noise rejection is required. Keep the UART trace away from clocks and power-converter switching edges, and ground the external transceiver return path properly to prevent data corruption.

Do not approve a replacement based on the TSSOP-16 footprint alone. For PI7C9X1170BCLE and PI7C9X1170BBLEX, confirm the exact ordering suffix, device revision, exposed functions, supply limits, timing, and marking against the manufacturer datasheet. The target supports up to eight programmable GPIO pins, but alternate parts must provide the required pin functions. Also verify that the host firmware can configure the selected variant's baud-rate and data-format behavior.

Decouple the bridge close to its supply pins using the capacitance and placement specified in the manufacturer datasheet. Because the family is described as having low operating and sleeping current, check the actual mode currents at the system supply voltage before treating the controller as negligible in a power budget. Confirm that every I2C, SPI, UART, and GPIO signal remains within the device's input and output limits.

Uyumluluk Bilgisi

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Kadmiyumdan Arınmış
Unknown
Klorofillerden Arınmış
Unknown
Çatışma Minerali
Unknown

The component is identified as an industrial-grade interface IC, but no specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals declarations are stated in the available product information.

Veri doğrulanma tarihi: 2026-11-17 — XAIPART bileşen mühendislik ekibi tarafından doğrulanmış ve derlenmiş veri

İlgili Aramalar

PI7C9X1170BCLEX datasheet PI7C9X1170BCLEX pinout PI7C9X1170BCLEX datasheet pdf PI7C9X1170BCLEX equivalent PI7C9X1170BCLEX replacement PI7C9X1170BCLEX cross reference PI7C9X1170BCLEX vs PI7C9X1170BCLE PI7C9X1170BCLEX TSSOP-16 PI7C9X1170BCLEX 33Mbps UART PI7C9X1170BCLEX I2C SPI bridge PI7C9X1170BCLEX price PI7C9X1170BCLEX stock Diodes Incorporated PI7C9X1170BCLEX PI7C9X1170 application circuit PI7C9X1170 TSSOP-16 pinout

İlgili Bileşenler ve Terimler

Diodes Incorporated PI7C9X1170BCLEX PI7C9X1170BCLE PI7C9X1170BBLEX I2C/SPI-to-UART bridge serial interface controller communication controller interface IC semiconductor UART I2C SPI GPIO 33Mbps TSSOP-16 TSSOP package family surface-mount technology single-channel bridge industrial control embedded instrumentation test and measurement peripheral adapter programmable general-purpose I/O logic-level UART
Hızlı Teklif RFQ
Detayları tam doldurun — satış ekibimiz 24 saat içinde yanıt verecek
Parça Numarası Üretici Paket QTY Hedef Fiyat Genişletilmiş
✓
Teklif gönderildi!

24 saat içinde e-postanıza yanıt vereceğiz

1
RFQ Gönderildi
2
Teklif Alındı
3
Sipariş Yerleştirildi
4
Ödeme
5
Gönderildi
6
Teslim Edildi
RFQ Detaylarını Görüntüle