Texas Instruments

SN75150P - Dual RS-232 Line Driver | Texas Instruments

MPN: SN75150P ✓ সক্রিয়
12 V Vdss 8-pin PDIP (P) Package
সর্বনিম্ন অর্ডার পরিমাণ: 1 |

SN75150P সারাংশ

The Texas Instruments SN75150P is a monolithic dual RS-232 line driver designed for data-terminal equipment and data-communication equipment interfaces. It supports data rates up to 20 kbit/s with a full 2500 pF load, accepts TTL-compatible logic inputs, and operates from dual 12 V and -12 V power supplies. The device is packaged in an 8-pin PDIP (P) package and is characterized for operation from 0°C to 70°C.

An RS-232 line driver is a signal-conditioning interface integrated circuit that converts low-voltage logic-level inputs into bipolar voltage levels suitable for RS-232 communications. Within the broader hierarchy of interface ICs, a line driver sits between digital logic and a communications transceiver. It increases voltage swing and drive capability so that a logic signal can reliably cross an RS-232 cable or short data-transmission line.

The SN75150 provides two independent driver channels, allowing one package to service bidirectional or multiport serial interfaces. Its characterized 20 kbit/s rate under a 2500 pF load supports legacy RS-232 equipment, control ports, instrumentation links, and industrial data communication. The dual 12 V and -12 V supply arrangement produces the positive and negative voltage swing required by TIA/EIA-232-F, while the short-circuit withstand capability helps protect the output stage during abnormal line conditions.

The logic inputs are compatible with most TTL families, making the SN75150P suitable for systems that use TTL-compatible microcontrollers, microprocessors, UARTs, or other digital controllers. Its monolithic construction gives both channels consistent operating characteristics within one package. The device is also useful as a level translator, as a driver for relatively short single-ended lines, and as a MOS-device driver where the required interface voltage and current behavior match the device ratings.

Typical applications include legacy RS-232 ports, data-terminal and data-communication equipment, short-distance serial links, industrial control interfaces, and equipment that requires a pair of bipolar RS-232 outputs. Designers should pair the two channels with the appropriate receiver when full bidirectional communication is needed. The SN75150 is a driver rather than a combined transceiver, so input and output signal direction must be assigned separately.

When laying out a design, place the device close enough to the line-driver interface to minimize exposure of logic-level input traces to noise, and route the RS-232 outputs directly toward the protected connector or cable interface. Confirm that the external supply rails provide the required positive and negative voltages and that the total channel loading remains within the characterized load and data-rate conditions. Maintain suitable common-mode grounding between communicating equipment.

This product page combines the manufacturer interface description with practical RS-232 design guidance, verified package information, function-specific application examples, and a cautious drop-in comparison. It helps engineers identify whether the SN75150P matches the required channel count, data rate, supply arrangement, package, and environmental range before committing a board design to this legacy-compatible interface device.

এর জন্য ড্রপ-ইন বিকল্প SN75150P — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।

SN75150PE4

✅ ড্রপ-ইন
📦 8-pin PDIP (P)
Same dual-driver function and 8-pin PDIP format; family data rate remains 20 kbit/s at 2500 pF, with 0% change in those characterized key parameters.

📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)

SN75150PS

✅ ড্রপ-ইন
📦 8-pin PDIP (P)
Same dual-driver function and 8-pin PDIP format; family data rate remains 20 kbit/s at 2500 pF, with 0% change in those characterized key parameters.

📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)

UA9636ACP

✅ ড্রপ-ইন
📦 8-pin PDIP
Cross-brand dual RS-232 driver with the same 8-pin PDIP class; the comparison identifies equivalent driver functionality, while device-specific limits require pin and rating verification.

📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)

SN75150P বিশেষণ

Product Type Dual RS-232 line driver
Driver Channel Count 2 channels
Maximum Characterized Data Rate 20 kbit/s
Characterized Load 2500 pF
Positive Supply 12 V
Negative Supply -12 V
অপারেটিং তাপমাত্রার পরিসর 0°C to 70°C
Interface Standard TIA/EIA-232-F
Recommendation Compatibility ITU V.28
Logic Input Compatibility Compatible with most TTL families
Output Short-Circuit Withstand Sustained output short circuit to any low-impedance voltage between 25 V
Maximum Output Transition Time 2 µs through the -3 V transition region under full load
প্যাকেজ 8-pin PDIP (P)
Package Pin Count 8 pins
মাউন্টিং টাইপ Through-hole PDIP
Logic Level Bipolar RS-232 output

SN75150P 8 pins পিন কনফিগারেশন গাইড

SN75150P (8 pins প্যাকেজ)-এর পিন কনফিগারেশন। পিন নম্বরিং, ফাংশন এবং সংযোগ ডায়াগ্রাম প্রস্তুতকারকের ডেটাশিটে সংজ্ঞায়িত করা আছে। সঠিক ফুটপ্রিন্ট এবং সোল্ডারিং নির্দেশিকার জন্য এটি দেখুন।

SN75150P-এর জন্য 8 pins প্যাকেজ পিনআউট ডায়াগ্রাম

এর জন্য বিস্তারিত পিনআউট ডেটা পাওয়া যায়নি SN75150P.

দেখুন ডেটাশিট সম্পূর্ণ পিন কনফিগারেশনের জন্য।

সাধারণ ব্যবহার

SN75150P এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Legacy RS-232 Equipment Interfaces, Industrial Control and Data Links, Instrumentation Measurement Interfaces, Data-Terminal and Communication Equipment, TTL-to-RS-232 Level Translation, Short Single-Ended Data Transmission.

🔧

Legacy RS-232 Equipment Interfaces

The SN75150P fits legacy equipment that needs two logic-level inputs converted into bipolar RS-232 outputs. According to the Texas Instruments SN75150 product page, the device is designed for data-terminal and data-communication equipment interfaces and supports 20 kbit/s with a full 2500 pF load. Place the IC between a TTL-compatible UART or control logic and an RS-232 connector, with 12 V and -12 V rails available. The important system-level consideration is cable loading: the characterized 2500 pF condition should be reviewed against the expected line length and receiver capacitance.

🏭

Industrial Control and Data Links

SN75150P is suitable for short industrial control links that terminate at legacy RS-232 equipment. Its two driver channels allow two logic signals to be converted without using separate single-channel packages, while the documented 20 kbit/s rate under 2500 pF loading provides a clear basis for line-rate validation. The TTL-compatible inputs simplify interfacing with conventional control logic, and the 0°C to 70°C characterization defines the environmental envelope. Industrial equipment requiring a wider temperature range or a different supply architecture should select a more suitably rated interface device.

⚡

Instrumentation Measurement Interfaces

The SN75150P can translate instrumentation control signals into RS-232 levels for a host, test controller, or service interface. Its two channels are useful when separate request and status signals must share one interface connector, and the 20 kbit/s characterized rate is appropriate for many configuration and measurement-control protocols. Use TTL-compatible source logic at the inputs and a receiver on the return path. The designer should account for the bipolar supply requirement and verify that the attached test equipment does not exceed the characterized capacitive load.

🌐

Data-Terminal and Communication Equipment

SN75150P was developed for the interface between data-terminal equipment and data-communication equipment, making it appropriate for original RS-232 equipment architectures. The monolithic dual-driver implementation places two channels in one 8-pin PDIP, reducing the number of separate line-driver packages needed on a communications board. According to the Texas Instruments product page, the logic inputs are compatible with most TTL families, which supports integration with established terminal-control hardware. The design must preserve the specified positive and negative supply rails and should include receiver circuitry for bidirectional communication.

🔧

TTL-to-RS-232 Level Translation

SN75150P provides a dedicated TTL-to-RS-232 conversion function for boards whose logic section must communicate with a bipolar serial port. The two channels make it practical to translate both a transmit signal and another independently controlled line in a single package. The Texas Instruments SN75150 description specifically identifies level translation as an application and states that the inputs are compatible with most TTL families. Use the driver outputs for the cable side of the interface, keep the logic-side traces short, and verify output polarity and signal direction against the receiver schematic.

📡

Short Single-Ended Data Transmission

The SN75150P can also serve as a line driver for relatively short, single-ended data-transmission paths identified by the manufacturer. Its characterized 20 kbit/s operation provides a practical upper reference when selecting cable length, baud rate, and capacitive loading. Because this is a bipolar RS-232 driver rather than a low-voltage differential transceiver, the circuit must not be treated as an RS-485 or isolated communication interface. Confirm the logic levels, supply polarity, grounding method, and receiver thresholds across the complete connection before using it in a custom link.

What is the SN75150P?
The SN75150P is a Texas Instruments monolithic dual RS-232 line driver with two driver channels in an 8-pin PDIP package. According to the Texas Instruments SN75150 product page, it is intended for data-terminal equipment and data-communication equipment interfaces, including TIA/EIA-232-F applications. It supports operation from 12 V and -12 V supplies, accepts TTL-compatible logic inputs, and can transmit at 20 kbit/s with a full 2500 pF load.
What are the key specifications of SN75150P that engineers should know?
The SN75150P provides two RS-232 driver channels, a characterized maximum data rate of 20 kbit/s, and operation with a full 2500 pF load. According to the Texas Instruments SN75150 product page, its TTL-compatible inputs work with most TTL families, while its bipolar outputs use 12 V and -12 V supplies. The 8-pin PDIP (P) package is characterized from 0°C to 70°C, and the outputs can withstand a sustained short circuit to a low-impedance voltage between 25 V.
What is the operating voltage of SN75150P?
The SN75150P operates from dual 12 V and -12 V power supplies. The Texas Instruments SN75150 product page identifies these positive and negative supply rails as the operating arrangement used to generate the bipolar RS-232 voltage levels. Designers should not treat the device as a single-supply or 5 V interface circuit, because its RS-232 outputs require both supply polarities and the logic inputs are separate from the line-side output voltage.
What is the maximum data rate of SN75150P?
The SN75150P is characterized to transmit at up to 20 kbit/s when driving a full 2500 pF load. According to the Texas Instruments SN75150 product page, this operating point reflects both logic timing and the capacitive loading commonly introduced by RS-232 cables and connected equipment. Higher baud rates or heavier loads should not be treated as guaranteed by this characterization, so cable length and receiver loading must be checked against the application.
Where can I download the SN75150P datasheet PDF?
The official SN75150 documentation is available through the Texas Instruments SN75150 product page at https://www.ti.com/product/SN75150. This page provides the manufacturer’s product information and datasheet access for the SN75150 family. When designing a new board, use the Texas Instruments document for the final pin assignments, electrical limits, operating conditions, and application guidance instead of relying on an unofficial mirror.
Where can I find the SN75150P pinout?
The SN75150P pinout is defined in the Texas Instruments SN75150 datasheet and corresponds to its 8-pin PDIP (P) package. The manufacturer part-details listing identifies the P package as an 8-pin PDIP. Use the pin-description table in the manufacturer datasheet when assigning the two driver inputs, two outputs, supply pins, ground connection, and any no-connect position in the PCB layout.
Is SN75150P suitable for RS-232 communications?
The SN75150P is specifically designed for RS-232 data-terminal and data-communication interfaces. According to the Texas Instruments product description, the device meets or exceeds the requirements associated with TIA/EIA-232-F and supports transmission at 20 kbit/s with a 2500 pF load. It is appropriate for legacy serial equipment, control interfaces, and short data-transmission lines where TTL logic must be converted to bipolar RS-232 levels.
Can SN75150P drive a UART?
The SN75150P can receive TTL-compatible digital inputs from a UART and convert them into bipolar RS-232 driver outputs. According to the Texas Instruments SN75150 product page, its inputs are compatible with most TTL families, while its two channels provide independent RS-232 outputs. The circuit still requires 12 V and -12 V supplies, and the associated receiver should be used on the return path for a complete bidirectional RS-232 link.
What is the difference between SN75150P and SN75150PE4?
The SN75150P and SN75150PE4 are related 8-pin PDIP dual-line-driver options listed in the same Texas Instruments family, so the package and primary RS-232 driver function align closely. The manufacturer’s 20 kbit/s rate at 2500 pF description applies to the SN75150 family. Confirm the exact temperature grade, marking, and orderable status for the specific suffix before replacing one device with the other, particularly if environmental qualification is required.
What can replace an SN75150P?
A suitable SN75150P replacement must provide two RS-232 driver channels, an 8-pin PDIP footprint, compatible bipolar supply operation, and logic inputs that can be driven by the existing controller. SN75150PE4 and SN75150PS are related family choices, while UA9636ACP is a cross-brand comparison candidate. Because the device is a driver rather than a combined transceiver, verify every pin and the original manufacturer’s electrical limits before treating any candidate as a direct replacement.
Is SN75150P the same as UA9636ACP?
SN75150P and UA9636ACP are both compared as RS-232 line-driver devices, but they are not automatically identical. SN75150P is specified by Texas Instruments for 20 kbit/s operation with a 2500 pF load and uses an 8-pin PDIP package. UA9636ACP is a competing dual-driver device with its own electrical ratings. Confirm pinout, supply voltage, data rate, load capability, and temperature range before substituting one for the other.
When should I choose SN75150P over another dual RS-232 driver?
Choose SN75150P when the design specifically needs the established SN75150 function, two RS-232 channels, an 8-pin PDIP package, and the documented 20 kbit/s operation with a 2500 pF load. According to the Texas Instruments product page, its inputs are TTL-compatible, which simplifies integration with conventional digital controllers. Select another candidate only after checking pin-level compatibility, supply rails, output swing, short-circuit behavior, temperature range, and application qualification.
Is SN75150P suitable for industrial control and instrumentation?
The SN75150P can be used in industrial control and instrumentation interfaces when the system remains within its characterized 0°C to 70°C range and uses suitable 12 V and -12 V rails. The Texas Instruments SN75150 product page identifies level translation, short single-line data transmission, and MOS-device driving as additional uses. Environmental requirements outside the characterized range should be evaluated against a suitably qualified alternative rather than inferred from the package alone.
Where can I buy SN75150P online and what is its price?
The SN75150P can be requested through the Request a Quote form on this page, where current pricing, availability, and lead time should be confirmed for the exact 8-pin PDIP ordering code. The manufacturer lists the SN75150P as a dual line driver in an 8-pin PDIP package, and current distributor pages identify the same ordering code. Request a quote rather than relying on a stale starting-price figure for purchasing decisions.
What is the lead time and stock status for SN75150P?
Current stock and lead time for SN75150P should be confirmed through the Request a Quote form on this page before the parts are reserved for production. The Texas Instruments product and distributor listings identify the component as an 8-pin PDIP dual RS-232 line driver, but availability can change independently of technical specifications. Provide the required quantity, delivery location, and target schedule when requesting the quotation.
What design cautions apply to SN75150P power and signal routing?
SN75150P must receive both 12 V and -12 V supplies, and its RS-232 outputs should be routed toward the cable or connector rather than exposed to long parallel logic traces. According to the Texas Instruments product information, the device is a dual driver whose inputs are TTL-compatible. Keep the logic side and line side functionally separate in the schematic, use appropriate bypassing near the supply pins, and confirm that ground references and cable loading are suitable for the connected equipment.

এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা SN75150P — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।

নির্বাচন গাইড

Choose SN75150P when the equipment uses two bipolar RS-232 outputs, an 8-pin PDIP footprint, TTL-compatible control signals, and 12 V and -12 V rails. Its documented 20 kbit/s rate at 2500 pF makes it particularly suitable for legacy terminals, industrial control links, and instrumentation interfaces with known cable loading. SN75150PE4 or SN75150PS may be preferable when the exact orderable suffix, environmental grade, or lifecycle requirements better match the system. Consider UA9636ACP only after independently confirming pin assignments, supply limits, output swing, short-circuit behavior, temperature range, and data-rate specifications. SN75150P is not the correct choice for systems needing an integrated receiver, a 3.3 V or 5 V-only interface, RS-485 differential signaling, or isolation. For those requirements, select a combined transceiver, single-supply RS-232 device, differential transceiver, or isolated interface circuit rather than assuming electrical or pin compatibility.

বিকল্পের সাথে তুলনা

পারামিটার এই পণ্য SN75150PE4 SN75150PS UA9636ACP
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Package 8-pin PDIP (P) 8-pin PDIP (P) 8-pin PDIP (P) 8-pin PDIP
Driver Channel Count 2 channels 2 channels 2 channels 2 channels
Product Type Dual RS-232 line driver Dual RS-232 line driver Dual RS-232 line driver Dual RS-232 line driver

মূল পার্থক্যসমূহ

  • Documented performance under a full capacitive load (বনামUA9636ACP)
  • TTL-compatible input integration (বনামUA9636ACP)
  • Family-level continuity within the original interface architecture (বনামUA9636ACP)

ডিজাইন নোট

Provide separate 12 V and -12 V rails with local high-frequency bypass capacitors placed close to the device supply pins. The SN75150 is a bipolar RS-232 driver rather than a single-supply interface IC, so both rail polarities are fundamental to valid output levels. Keep converter switching noise away from the logic-input side, and verify supply sequencing, rail tolerance, and ground reference against the manufacturer's electrical-characteristics table before releasing the PCB layout.

Route the two RS-232 outputs directly toward the connector or cable-side circuitry and keep the TTL-compatible logic inputs away from those outputs. Preserve the 8-pin PDIP footprint and use the datasheet pin-description table for all assignments. Because the device is characterized at 20 kbit/s with a full 2500 pF load, check actual cable and receiver capacitance; longer or heavily terminated cables can exceed the load condition behind the stated data rate.

Do not substitute SN75150P for a combined RS-232 transceiver without checking every connection: SN75150P provides two driver outputs but no integrated receiver channels. Likewise, do not treat the bipolar outputs as TTL-compatible logic outputs. Validate input polarity, output polarity, supply rails, no-connect positions, and the receiver threshold before power-up, and avoid applying an RS-485 or differential-interface assumption to this single-ended driver.

কমপ্লায়েন্স তথ্য

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
লিড ফ্রি
Unknown
হ্যালোজেন ফ্রি
Unknown
কনফ্লিক্ট মিনারেলস
Unknown

The SN75150P is a commercial-temperature 0°C to 70°C interface IC in an 8-pin PDIP package. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations were not identified in the manufacturer information and remain unknown.

ডেটা যাচাই করা হয়েছে: 2026-11-09 — ডেটা XAIPART-এর কম্পোনেন্ট ইঞ্জিনিয়ারিং টিম দ্বারা যাচাই ও কিউরেট করা হয়েছে

সম্পর্কিত অনুসন্ধান

SN75150P SN75150P datasheet SN75150P datasheet pdf SN75150P pinout SN75150P specifications SN75150P equivalent SN75150P replacement SN75150P vs UA9636ACP Texas Instruments SN75150P SN75150P RS-232 application circuit SN75150P 8-pin PDIP pinout SN75150P price

সম্পর্কিত কম্পোনেন্ট ও শর্তাবলী

Texas Instruments SN75150P SN75150PE4 SN75150PS UA9636ACP RS-232 TIA/EIA-232-F ITU V.28 dual line driver interface IC RS-232 transceiver TTL-compatible logic level translator data-terminal equipment data-communication equipment 20 kbit/s 2500 pF load 12 V and -12 V supplies 8-pin PDIP through-hole package bipolar output short-circuit withstand MOS-device driver 0°C to 70°C
তাৎক্ষণিক বিলওয়াছে রেকোজিউইট
সম্পূর্ণ বিবরণ পূরণ করুন — আমাদের সেলস টিম 24 ঘণ্টার মধ্যে উত্তর দেবে
পার্ট নম্বর উৎপাদক প্যাকেজ QTY লক্ষ্যমূল্য প্রসারিত
✓
বিল প্রস্তুত করা হয়েছে!

আমরা ২৪ ঘণ্টার মধ্যে আপনার ইমেইলে প্রত্যুত্তর দেব

1
RFQ জমা হয়েছে
2
কোটেশন পাওয়া গেছে
3
অর্ডার দেওয়া হয়েছে
4
পেমেন্ট
5
শিপ করা হয়েছে
6
ডেলিভারি হয়েছে
RFQ বিবরণ দেখুন