SN75150P - Dual RS-232 Line Driver | Texas Instruments
MPN: SN75150P ✓ Hoạt độngSN75150P Tóm tắt
An RS-232 line driver is a signal-conditioning interface integrated circuit that converts low-voltage logic-level inputs into bipolar voltage levels suitable for RS-232 communications. Within the broader hierarchy of interface ICs, a line driver sits between digital logic and a communications transceiver. It increases voltage swing and drive capability so that a logic signal can reliably cross an RS-232 cable or short data-transmission line.
The SN75150 provides two independent driver channels, allowing one package to service bidirectional or multiport serial interfaces. Its characterized 20 kbit/s rate under a 2500 pF load supports legacy RS-232 equipment, control ports, instrumentation links, and industrial data communication. The dual 12 V and -12 V supply arrangement produces the positive and negative voltage swing required by TIA/EIA-232-F, while the short-circuit withstand capability helps protect the output stage during abnormal line conditions.
The logic inputs are compatible with most TTL families, making the SN75150P suitable for systems that use TTL-compatible microcontrollers, microprocessors, UARTs, or other digital controllers. Its monolithic construction gives both channels consistent operating characteristics within one package. The device is also useful as a level translator, as a driver for relatively short single-ended lines, and as a MOS-device driver where the required interface voltage and current behavior match the device ratings.
Typical applications include legacy RS-232 ports, data-terminal and data-communication equipment, short-distance serial links, industrial control interfaces, and equipment that requires a pair of bipolar RS-232 outputs. Designers should pair the two channels with the appropriate receiver when full bidirectional communication is needed. The SN75150 is a driver rather than a combined transceiver, so input and output signal direction must be assigned separately.
When laying out a design, place the device close enough to the line-driver interface to minimize exposure of logic-level input traces to noise, and route the RS-232 outputs directly toward the protected connector or cable interface. Confirm that the external supply rails provide the required positive and negative voltages and that the total channel loading remains within the characterized load and data-rate conditions. Maintain suitable common-mode grounding between communicating equipment.
This product page combines the manufacturer interface description with practical RS-232 design guidance, verified package information, function-specific application examples, and a cautious drop-in comparison. It helps engineers identify whether the SN75150P matches the required channel count, data rate, supply arrangement, package, and environmental range before committing a board design to this legacy-compatible interface device.
Bộ thay thế dễ dàng lắp đặt cho SN75150P — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
SN75150PE4
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
SN75150PS
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
UA9636ACP
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
SN75150P Thông số kỹ thuật
| Product Type | Dual RS-232 line driver |
| Driver Channel Count | 2 channels |
| Maximum Characterized Data Rate | 20 kbit/s |
| Characterized Load | 2500 pF |
| Positive Supply | 12 V |
| Negative Supply | -12 V |
| Khoảng nhiệt độ hoạt động | 0°C to 70°C |
| Interface Standard | TIA/EIA-232-F |
| Recommendation Compatibility | ITU V.28 |
| Logic Input Compatibility | Compatible with most TTL families |
| Output Short-Circuit Withstand | Sustained output short circuit to any low-impedance voltage between 25 V |
| Maximum Output Transition Time | 2 µs through the -3 V transition region under full load |
| Hộp | 8-pin PDIP (P) |
| Package Pin Count | 8 pins |
| Kiểu lắp đặt | Through-hole PDIP |
| Logic Level | Bipolar RS-232 output |
Hướng dẫn cấu hình chân SN75150P 8 pins
Cấu hình chân cho SN75150P (8 pins gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho SN75150P.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
SN75150P phù hợp cho 6 Áp dụngs: Legacy RS-232 Equipment Interfaces, Industrial Control and Data Links, Instrumentation Measurement Interfaces, Data-Terminal and Communication Equipment, TTL-to-RS-232 Level Translation, Short Single-Ended Data Transmission.
Legacy RS-232 Equipment Interfaces
The SN75150P fits legacy equipment that needs two logic-level inputs converted into bipolar RS-232 outputs. According to the Texas Instruments SN75150 product page, the device is designed for data-terminal and data-communication equipment interfaces and supports 20 kbit/s with a full 2500 pF load. Place the IC between a TTL-compatible UART or control logic and an RS-232 connector, with 12 V and -12 V rails available. The important system-level consideration is cable loading: the characterized 2500 pF condition should be reviewed against the expected line length and receiver capacitance.
Được đề xuất
Industrial Control and Data Links
SN75150P is suitable for short industrial control links that terminate at legacy RS-232 equipment. Its two driver channels allow two logic signals to be converted without using separate single-channel packages, while the documented 20 kbit/s rate under 2500 pF loading provides a clear basis for line-rate validation. The TTL-compatible inputs simplify interfacing with conventional control logic, and the 0°C to 70°C characterization defines the environmental envelope. Industrial equipment requiring a wider temperature range or a different supply architecture should select a more suitably rated interface device.
Được đề xuất
Instrumentation Measurement Interfaces
The SN75150P can translate instrumentation control signals into RS-232 levels for a host, test controller, or service interface. Its two channels are useful when separate request and status signals must share one interface connector, and the 20 kbit/s characterized rate is appropriate for many configuration and measurement-control protocols. Use TTL-compatible source logic at the inputs and a receiver on the return path. The designer should account for the bipolar supply requirement and verify that the attached test equipment does not exceed the characterized capacitive load.
Được đề xuất
Data-Terminal and Communication Equipment
SN75150P was developed for the interface between data-terminal equipment and data-communication equipment, making it appropriate for original RS-232 equipment architectures. The monolithic dual-driver implementation places two channels in one 8-pin PDIP, reducing the number of separate line-driver packages needed on a communications board. According to the Texas Instruments product page, the logic inputs are compatible with most TTL families, which supports integration with established terminal-control hardware. The design must preserve the specified positive and negative supply rails and should include receiver circuitry for bidirectional communication.
Được đề xuất
TTL-to-RS-232 Level Translation
SN75150P provides a dedicated TTL-to-RS-232 conversion function for boards whose logic section must communicate with a bipolar serial port. The two channels make it practical to translate both a transmit signal and another independently controlled line in a single package. The Texas Instruments SN75150 description specifically identifies level translation as an application and states that the inputs are compatible with most TTL families. Use the driver outputs for the cable side of the interface, keep the logic-side traces short, and verify output polarity and signal direction against the receiver schematic.
Được đề xuất
Short Single-Ended Data Transmission
The SN75150P can also serve as a line driver for relatively short, single-ended data-transmission paths identified by the manufacturer. Its characterized 20 kbit/s operation provides a practical upper reference when selecting cable length, baud rate, and capacitive loading. Because this is a bipolar RS-232 driver rather than a low-voltage differential transceiver, the circuit must not be treated as an RS-485 or isolated communication interface. Confirm the logic levels, supply polarity, grounding method, and receiver thresholds across the complete connection before using it in a custom link.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho SN75150P — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | SN75150PE4 | SN75150PS | UA9636ACP |
|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 8-pin PDIP (P) | 8-pin PDIP (P) | 8-pin PDIP (P) | 8-pin PDIP |
| Driver Channel Count | 2 channels | 2 channels | 2 channels | 2 channels |
| Product Type | Dual RS-232 line driver | Dual RS-232 line driver | Dual RS-232 line driver | Dual RS-232 line driver |
Bảo phân biệt quan trọng
- Documented performance under a full capacitive load (vsUA9636ACP)
- TTL-compatible input integration (vsUA9636ACP)
- Family-level continuity within the original interface architecture (vsUA9636ACP)
Ghi chú thiết kế
Provide separate 12 V and -12 V rails with local high-frequency bypass capacitors placed close to the device supply pins. The SN75150 is a bipolar RS-232 driver rather than a single-supply interface IC, so both rail polarities are fundamental to valid output levels. Keep converter switching noise away from the logic-input side, and verify supply sequencing, rail tolerance, and ground reference against the manufacturer's electrical-characteristics table before releasing the PCB layout.
Route the two RS-232 outputs directly toward the connector or cable-side circuitry and keep the TTL-compatible logic inputs away from those outputs. Preserve the 8-pin PDIP footprint and use the datasheet pin-description table for all assignments. Because the device is characterized at 20 kbit/s with a full 2500 pF load, check actual cable and receiver capacitance; longer or heavily terminated cables can exceed the load condition behind the stated data rate.
Do not substitute SN75150P for a combined RS-232 transceiver without checking every connection: SN75150P provides two driver outputs but no integrated receiver channels. Likewise, do not treat the bipolar outputs as TTL-compatible logic outputs. Validate input polarity, output polarity, supply rails, no-connect positions, and the receiver threshold before power-up, and avoid applying an RS-485 or differential-interface assumption to this single-ended driver.
Thông tin tuân thủ
The SN75150P is a commercial-temperature 0°C to 70°C interface IC in an 8-pin PDIP package. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations were not identified in the manufacturer information and remain unknown.