SN75157D - Dual Differential Line Receiver | Texas Instruments
MPN: SN75157D ✓ সক্রিয়SN75157D সারাংশ
A differential line receiver converts a small voltage difference between two conductors into a logic-level signal while rejecting common-mode noise. In the signal path, the line receiver sits between a remote transmitter and a digital controller, logic gate array, or data-processing system. The SN75157D can accept either a differential input or a single-ended input at each receiver channel, making it useful in industrial control, instrumentation, data acquisition, and legacy communication equipment.
The SN75157D uses Schottky circuitry and provides TTL-compatible outputs. According to the manufacturer datasheet, the device is supplied in 8-pin dual-in-line and small-outline versions, with the SN75157D identifying the SOIC-8 package. Its stated operating temperature range is 0 °C to 70 °C, positioning it as a commercial-temperature interface device. The maximum signaling rate is listed as 10 Mbit/s, supporting moderate-speed point-to-point and multidrop data links.
The device includes two independent receiver channels, one 5 V power connection, a ground connection, and six signal pins. Differential inputs reduce susceptibility to externally induced noise because the receiver responds primarily to the voltage between the input pair rather than to their shared voltage relative to ground. Published comparison information lists fault protection from -10 V to 15 V for the SN75157D, although the input protection behavior and application limits should be verified against the complete manufacturer datasheet before applying fault voltages to a design.
Typical uses include industrial RS-422 and RS-423 links, data acquisition interfaces, telemetry receivers, and test equipment. Because both receiver channels are independent, one SN75157D can recover two signals and reduce component count compared with two single-channel receivers. The logic outputs can connect directly to TTL or CMOS-compatible receiving logic after checking input thresholds and timing requirements.
The primary design consideration is signal integrity. Route the differential pair as a closely matched pair, terminate the line according to the selected network topology, and keep the receiver away from high-current switching paths. Do not substitute the SN75157D for a line driver or RS-232 transceiver; the receiver's TTL outputs and differential input architecture support only the corresponding receiver application.
এর জন্য ড্রপ-ইন বিকল্প SN75157D — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।
এই সিরিজের ভ্যারিয়েন্ট
একই সিরিজের মডেল যেগুলো drop-in compatible SN75157D (একই form factor এবং footprint) — পার্থক্য রয়েছে Internal Technology, Operating Temperature Range, Package, Supply Voltage Range.
SN75156D
✅ ড্রপ-ইন📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
SN75157D বিশেষণ
| Device Type | Dual differential line receiver |
| Number of Receiver Channels | 2 channels |
| Number of Transmitter Channels | 0 channels |
| Nominal Supply Voltage | 5 V |
| Supply Voltage Range | 4.75 V to 5.25 V |
| Maximum Signaling Rate | 10 Mbit/s |
| Input Compatibility | Differential or single-ended inputs |
| Output Compatibility | TTL-compatible outputs |
| Internal Technology | Schottky circuitry |
| Supported Standards | EIA/TIA-422-B, EIA/TIA-423-B, ITU V.10, ITU V.11 |
| অপারেটিং তাপমাত্রার পরিসর | 0 °C to 70 °C |
| প্যাকেজ | 8-pin SOIC, 3.90 mm width |
| মাউন্টিং টাইপ | Surface mount |
| Input Fault Protection Range | -10 V to 15 V |
SN75157D পিন কনফিগারেশন
| পিন 1 | 1B — Inverting input for receiver 1 |
| পিন 2 | 1A — Noninverting input for receiver 1 |
| পিন 3 | GND — Ground connection |
| পিন 4 | 1Y — TTL-compatible output for receiver 1 |
| পিন 5 | 2Y — TTL-compatible output for receiver 2 |
| পিন 6 | VCC — 5 V power supply connection |
| পিন 7 | 2A — Noninverting input for receiver 2 |
| পিন 8 | 2B — Inverting input for receiver 2 |
সাধারণ ব্যবহার
SN75157D এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Industrial RS-422 Data Acquisition, Telemetry and Remote Sensor Interfaces, RS-423 Point-to-Point Communication, Legacy Computer and Peripheral Interconnect, Test and Measurement Instrumentation, Process Control and PLC Communication.
Industrial RS-422 Data Acquisition
The SN75157D suits two-channel industrial data acquisition when the remote equipment transmits balanced EIA/TIA-422-B signals over a cable run. Each receiver channel converts its differential input pair into a TTL-compatible output that can feed a controller or data-capture circuit, while the documented 10 Mbit/s signaling rate covers moderate-speed acquisition links. The single 5 V supply simplifies system powering. Place the receiver close to the protected board edge, route the pair as a matched pair, and apply the termination required by the line topology. Verify common-mode voltage and fault conditions at the connector because the published -10 V to 15 V protection range is not a substitute for a complete surge-protection design.
সুপারিশকৃত
Telemetry and Remote Sensor Interfaces
The SN75157D can recover two low-speed telemetry signals from a remote sensor or instrument, providing a compact interface between an external cable and on-board digital logic. Its differential or single-ended input capability accommodates instrument panels that expose either balanced or single-ended lines, while TTL-compatible outputs reduce the need for an additional logic-level conversion stage. The two independent channels keep the design compact when the system must monitor more than one measurement. Use consistent reference grounding, keep input traces away from motors and switching regulators, and verify that the transmitter's output levels satisfy the receiver thresholds documented in the manufacturer datasheet.
সুপারিশকৃত
RS-423 Point-to-Point Communication
The SN75157D supports EIA/TIA-423-B and ITU V.10 receive functions for equipment that uses a 5 V differential signaling arrangement rather than RS-232 voltage levels. Two receiver channels allow one device to monitor two incoming communications lines while the TTL outputs connect to a microprocessor, UART, or programmable logic. The 10 Mbit/s maximum signaling rate covers many legacy control and data-transfer links, although actual distance and rate are limited by the selected network and cable. Confirm the applicable standard's termination and grounding rules during design review, and validate signal integrity with representative cable lengths.
সুপারিশকৃত
Legacy Computer and Peripheral Interconnect
The SN75157D is appropriate for legacy computer and peripheral interconnects that terminate balanced data lines into standard logic levels. Its two receivers can recover separate control or data signals in one SOIC-8 device, reducing board area compared with discrete single-channel solutions. TTL-compatible outputs simplify connection to established digital buses, but the receiving system must still observe the timing and input-threshold requirements of the original interface. Route the pair away from high-current switching nodes, provide a stable 5 V rail, and test the assembled board with the intended connector and cable because legacy interfaces often depend on specific grounding practices.
সুপারিশকৃত
Test and Measurement Instrumentation
The SN75157D can serve as the front-end receiver in instrumentation that accepts two remote, low-level logic signals through balanced cabling. Differential reception helps reject common-mode disturbances that can otherwise affect precision measurement control systems, while the two-channel configuration supports complementary or independent channels. The device's 4.75 V to 5.25 V operating range suits conventional laboratory and industrial control supplies. Keep the analog and digital return paths managed according to the instrument architecture, and validate input thresholds with the actual source because single-ended operation changes the noise-immunity tradeoff compared with a fully balanced connection.
সুপারিশকৃত
Process Control and PLC Communication
The SN75157D fits process-control equipment that receives two differential command or status lines from a remote controller. The dual receiver arrangement reduces the component count compared with two single-channel parts, and the documented EIA/TIA-422-B compatibility supports established industrial communication designs. The commercial 0 °C to 70 °C temperature range requires separate qualification when the enclosure exceeds that range. Protection at the cable entry should be handled with appropriately selected network components, because the receiver's published input protection range does not replace surge or ESD design. Validate grounding and termination against the complete controller interface specification.
সুপারিশকৃত
সুপারিশকৃত পণ্যের সারসংক্ষেপ
এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা SN75157D — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।
নির্বাচন গাইড
বিকল্পের সাথে তুলনা
| পারামিটার | এই পণ্য | SN75156D |
|---|---|---|
| Brand | Texas Instruments | Texas Instruments |
| Package | 8-SOIC (0.154", 3.90mm Width) | 8-SOIC |
| Device Type | Dual differential line receiver | Line receiver |
মূল পার্থক্যসমূহ
- Two independent receiver channels in one SOIC-8 device (বনামSN75156D)
- Documented differential and single-ended input flexibility (বনামSN75156D)
- Compatibility with established balanced-interface standards (বনামSN75156D)
ডিজাইন নোট
Route each differential input as a closely matched pair and keep the pair away from switching-current paths. A common-mode voltage is present on a balanced line, so the useful signal is the voltage difference between the two conductors. Use a solid ground plane, avoid vias in the input path where practical, and apply protection or termination at the connector boundary only after checking how the selected interface topology affects signal amplitude.
Do not treat the SN75157D as an RS-232 device or as a line driver. It has two receiver channels and no transmitter channels, and its outputs are TTL-compatible rather than RS-232 voltage levels. Verify that the connected source supports the EIA/TIA-422-B, EIA/TIA-423-B, ITU V.10, or ITU V.11 receive requirements. Also check pin functions against the manufacturer pin-description table before revising an existing board.
Place the receiver close to the line connector so that the sensitive high-impedance inputs do not collect noise over a long PCB trace. Provide a stable 5 V rail with local high-frequency bypassing, keep the return path continuous, and maintain separation from unrelated analog or switching signals. The compact SOIC-8 footprint allows the two receiver channels to be placed near the connector while their TTL outputs route inward to the controller.
কমপ্লায়েন্স তথ্য
The device is a commercial-temperature 0 °C to 70 °C interface IC. No explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations were identified in the manufacturer page, datasheet snippet, or distributor records used for this page.