Texas Instruments

SN75157D - Dual Differential Line Receiver | Texas Instruments

Référence : SN75157D ✓ Actif
5 V Vdss EIA/TIA-422-B, EIA/TIA-423-B, ITU V.10, ITU V.11 Rds(on) 8-pin SOIC, 3.90 mm width Package
MOQ : 1 |

SN75157D Présentation

The Texas Instruments SN75157D is a dual differential line receiver in an 8-pin SOIC package. It receives two differential or single-ended signals and converts each into a TTL-compatible logic output. The device operates from a single 5 V supply, with a documented operating range of 4.75 V to 5.25 V, and supports signaling rates up to 10 Mbit/s. Its inputs are compatible with EIA/TIA-422-B, EIA/TIA-423-B, ITU V.10, and ITU V.11 line-driver outputs.

A differential line receiver converts a small voltage difference between two conductors into a logic-level signal while rejecting common-mode noise. In the signal path, the line receiver sits between a remote transmitter and a digital controller, logic gate array, or data-processing system. The SN75157D can accept either a differential input or a single-ended input at each receiver channel, making it useful in industrial control, instrumentation, data acquisition, and legacy communication equipment.

The SN75157D uses Schottky circuitry and provides TTL-compatible outputs. According to the manufacturer datasheet, the device is supplied in 8-pin dual-in-line and small-outline versions, with the SN75157D identifying the SOIC-8 package. Its stated operating temperature range is 0 °C to 70 °C, positioning it as a commercial-temperature interface device. The maximum signaling rate is listed as 10 Mbit/s, supporting moderate-speed point-to-point and multidrop data links.

The device includes two independent receiver channels, one 5 V power connection, a ground connection, and six signal pins. Differential inputs reduce susceptibility to externally induced noise because the receiver responds primarily to the voltage between the input pair rather than to their shared voltage relative to ground. Published comparison information lists fault protection from -10 V to 15 V for the SN75157D, although the input protection behavior and application limits should be verified against the complete manufacturer datasheet before applying fault voltages to a design.

Typical uses include industrial RS-422 and RS-423 links, data acquisition interfaces, telemetry receivers, and test equipment. Because both receiver channels are independent, one SN75157D can recover two signals and reduce component count compared with two single-channel receivers. The logic outputs can connect directly to TTL or CMOS-compatible receiving logic after checking input thresholds and timing requirements.

The primary design consideration is signal integrity. Route the differential pair as a closely matched pair, terminate the line according to the selected network topology, and keep the receiver away from high-current switching paths. Do not substitute the SN75157D for a line driver or RS-232 transceiver; the receiver's TTL outputs and differential input architecture support only the corresponding receiver application.

Alternatives de remplacement direct pour SN75157D — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.

Variantes de cette série

Modèles de la même série directement compatibles avec SN75157D (même facteur de forme et même empreinte) — différant par Internal Technology, Operating Temperature Range, Package, Supply Voltage Range.

Texas Instruments
Internal Technology: Monolithic low-power Schottky line receiver
Operating Temperature Range: 0°C to 70°C
Package: SOIC-16 (D)
Comparer avec SN75157D →

SN75156D

✅ Remplacement direct
📦 8-SOIC (0.154", 3.90mm Width)
Related TI line receiver; channel count and pin functions must be confirmed because SN75157D provides 2 receivers versus 0 transmitters and a 10 Mbit/s maximum rate

📋 Alternative de référence (hors catalogue)

SN75157D Spécifications

Device Type Dual differential line receiver
Number of Receiver Channels 2 channels
Number of Transmitter Channels 0 channels
Nominal Supply Voltage 5 V
Supply Voltage Range 4.75 V to 5.25 V
Maximum Signaling Rate 10 Mbit/s
Input Compatibility Differential or single-ended inputs
Output Compatibility TTL-compatible outputs
Internal Technology Schottky circuitry
Supported Standards EIA/TIA-422-B, EIA/TIA-423-B, ITU V.10, ITU V.11
Plage de température de fonctionnement 0 °C to 70 °C
Boîtier 8-pin SOIC, 3.90 mm width
Type de montage Surface mount
Input Fault Protection Range -10 V to 15 V

Configuration des broches de SN75157D

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
Broche 1 1B — Inverting input for receiver 1
Broche 2 1A — Noninverting input for receiver 1
Broche 3 GND — Ground connection
Broche 4 1Y — TTL-compatible output for receiver 1
Broche 5 2Y — TTL-compatible output for receiver 2
Broche 6 VCC — 5 V power supply connection
Broche 7 2A — Noninverting input for receiver 2
Broche 8 2B — Inverting input for receiver 2

Applications typiques

SN75157D convient pour 6 applications: Industrial RS-422 Data Acquisition, Telemetry and Remote Sensor Interfaces, RS-423 Point-to-Point Communication, Legacy Computer and Peripheral Interconnect, Test and Measurement Instrumentation, Process Control and PLC Communication.

🏭

Industrial RS-422 Data Acquisition

The SN75157D suits two-channel industrial data acquisition when the remote equipment transmits balanced EIA/TIA-422-B signals over a cable run. Each receiver channel converts its differential input pair into a TTL-compatible output that can feed a controller or data-capture circuit, while the documented 10 Mbit/s signaling rate covers moderate-speed acquisition links. The single 5 V supply simplifies system powering. Place the receiver close to the protected board edge, route the pair as a matched pair, and apply the termination required by the line topology. Verify common-mode voltage and fault conditions at the connector because the published -10 V to 15 V protection range is not a substitute for a complete surge-protection design.

📡

Telemetry and Remote Sensor Interfaces

The SN75157D can recover two low-speed telemetry signals from a remote sensor or instrument, providing a compact interface between an external cable and on-board digital logic. Its differential or single-ended input capability accommodates instrument panels that expose either balanced or single-ended lines, while TTL-compatible outputs reduce the need for an additional logic-level conversion stage. The two independent channels keep the design compact when the system must monitor more than one measurement. Use consistent reference grounding, keep input traces away from motors and switching regulators, and verify that the transmitter's output levels satisfy the receiver thresholds documented in the manufacturer datasheet.

🌐

RS-423 Point-to-Point Communication

The SN75157D supports EIA/TIA-423-B and ITU V.10 receive functions for equipment that uses a 5 V differential signaling arrangement rather than RS-232 voltage levels. Two receiver channels allow one device to monitor two incoming communications lines while the TTL outputs connect to a microprocessor, UART, or programmable logic. The 10 Mbit/s maximum signaling rate covers many legacy control and data-transfer links, although actual distance and rate are limited by the selected network and cable. Confirm the applicable standard's termination and grounding rules during design review, and validate signal integrity with representative cable lengths.

🖥️

Legacy Computer and Peripheral Interconnect

The SN75157D is appropriate for legacy computer and peripheral interconnects that terminate balanced data lines into standard logic levels. Its two receivers can recover separate control or data signals in one SOIC-8 device, reducing board area compared with discrete single-channel solutions. TTL-compatible outputs simplify connection to established digital buses, but the receiving system must still observe the timing and input-threshold requirements of the original interface. Route the pair away from high-current switching nodes, provide a stable 5 V rail, and test the assembled board with the intended connector and cable because legacy interfaces often depend on specific grounding practices.

🧪

Test and Measurement Instrumentation

The SN75157D can serve as the front-end receiver in instrumentation that accepts two remote, low-level logic signals through balanced cabling. Differential reception helps reject common-mode disturbances that can otherwise affect precision measurement control systems, while the two-channel configuration supports complementary or independent channels. The device's 4.75 V to 5.25 V operating range suits conventional laboratory and industrial control supplies. Keep the analog and digital return paths managed according to the instrument architecture, and validate input thresholds with the actual source because single-ended operation changes the noise-immunity tradeoff compared with a fully balanced connection.

⚙️

Process Control and PLC Communication

The SN75157D fits process-control equipment that receives two differential command or status lines from a remote controller. The dual receiver arrangement reduces the component count compared with two single-channel parts, and the documented EIA/TIA-422-B compatibility supports established industrial communication designs. The commercial 0 °C to 70 °C temperature range requires separate qualification when the enclosure exceeds that range. Protection at the cable entry should be handled with appropriately selected network components, because the receiver's published input protection range does not replace surge or ESD design. Validate grounding and termination against the complete controller interface specification.

Récapitulatif des produits recommandés

SN75157D Texas Instruments Utilisé dans : Industrial RS-422 Data Acquisition, Telemetry and Remote Sensor Interfaces, RS-423 Point-to-Point Communication, Legacy Computer and Peripheral Interconnect, Test and Measurement Instrumentation, Process Control and PLC Communication SN75156D Related TI line-receiver family member Utilisé dans : Industrial RS-422 Data Acquisition, Telemetry and Remote Sensor Interfaces, RS-423 Point-to-Point Communication, Legacy Computer and Peripheral Interconnect, Test and Measurement Instrumentation, Process Control and PLC Communication
What is the SN75157D used for?
The SN75157D is a dual differential line receiver for converting two incoming line signals into TTL-compatible logic outputs. According to the Texas Instruments manufacturer datasheet, each receiver input can be driven differentially or single-ended, and the device operates from a single 5 V supply. It is intended for EIA/TIA-422-B, EIA/TIA-423-B, ITU V.10, and ITU V.11 interfaces, commonly used in industrial control, instrumentation, and data-acquisition equipment.
What is the operating voltage range of the SN75157D?
The SN75157D operates from 4.75 V to 5.25 V around a nominal 5 V supply. The Texas Instruments product documentation identifies it as a single-supply differential receiver with TTL-compatible outputs. The supply range leaves 250 mV of design margin below and above 5 V, so a regulated 5 V rail should remain within the specified limits under temperature and load conditions.
Where can I download the SN75157D datasheet PDF?
The official SN75157D datasheet PDF is available from Texas Instruments at https://www.ti.com/lit/ds/symlink/sn75157.pdf. It describes the dual differential receiver architecture, supported line standards, electrical characteristics, and package pin assignments. Use the manufacturer document for design decisions because third-party copies may use older document revisions or omit device-specific ordering information.
What is the SN75157D pinout?
The SN75157D uses an 8-pin SOIC arrangement with two receiver pairs, two TTL outputs, a 5 V supply pin, and ground. In the standard counter-clockwise numbering, pins 1 and 2 form the first receiver input pair, pin 4 is the first output, pins 8 and 7 form the second receiver input pair, pin 5 is the second output, pin 6 connects to VCC, and pin 3 connects to GND. Verify the pin-description table in the manufacturer datasheet before assigning PCB tracks.
Can the SN75157D receive single-ended signals?
Yes, the SN75157D inputs are compatible with either a single-ended or a differential-line system. The Texas Instruments manufacturer datasheet identifies this dual-input capability as a defining feature of the receiver. A differential connection normally provides better rejection of common-mode noise, while single-ended operation can simplify point-to-point interfaces when the source and grounding arrangement is already controlled.
What is the maximum data rate of the SN75157D?
The SN75157D supports signaling rates up to 10 Mbit/s. This figure appears in published SN75157D comparison data and identifies the device as a moderate-speed dual line receiver. Practical throughput also depends on cable length, termination, source slew rate, receiver timing, and the application standard, so the 10 Mbit/s rating should not be treated as independent of system topology.
Is the SN75157D an RS-232 transceiver?
No, the SN75157D is a receiver only, not an RS-232 transceiver or a differential line driver. It contains two receiver channels and zero transmitter channels, as shown in the published SN75158D versus SN75157D comparison. Its differential inputs and TTL outputs are suited to RS-422 and RS-423 links. Use a separate RS-232 line driver or level translator when the physical interface requires RS-232 voltage levels.
What is the difference between SN75157D and SN75157DR?
SN75157D and SN75157DR identify the same underlying SN75157 dual differential line receiver function in the 8-pin SOIC family, with the trailing R identifying the supplier's reel-oriented packaging format. The published comparison describes the same 5 V nominal supply, two receiver channels, 10 Mbit/s maximum signaling rate, and -10 V to 15 V fault-protection range. Check the orderable drawing and tape-and-reel orientation before substituting shipping formats.
Can SN75156D replace the SN75157D?
The SN75156D should not be treated as a direct SN75157D replacement without verifying its channel count and pin assignment. A distributor comparison identifies SN75156D as a similar Texas Instruments line receiver, but the SN75157D is specifically documented as a two-channel receiver with zero transmitters. Confirm the exact pinout, input thresholds, timing, and enable requirements in each device's manufacturer datasheet before considering a board substitution.
What is the best drop-in replacement for SN75157D?
The closest same-family choice identified for the SN75157D is SN75156D, but it is not automatically a verified drop-in replacement. Both are Texas Instruments line receivers, while the SN75157D is confirmed as a dual differential receiver with two channels and a 10 Mbit/s maximum rate. A valid drop-in candidate must match the SOIC-8 footprint, pin functions, supply voltage, input thresholds, output timing, and channel count.
When should I choose the SN75157D instead of a single-channel receiver?
Choose the SN75157D when the design must recover two independent signals from one 8-pin package. Its two receiver channels reduce footprint and component count compared with two single-channel receivers, while the differential-capable inputs provide noise immunity for balanced interconnects. For a one-channel link, a single-channel receiver can reduce unused circuitry if its electrical characteristics and package are otherwise preferable.
Is the SN75157D suitable for industrial RS-422 interfaces?
The SN75157D is suitable for RS-422-family receiving applications because the Texas Instruments manufacturer datasheet states that it meets EIA/TIA-422-B and EIA/TIA-423-B requirements. Its 0 °C to 70 °C operating range identifies it as a commercial-temperature part, so additional temperature qualification may be needed for extended industrial environments. Confirm grounding, termination, and isolation requirements in the final interface design.
How should termination be handled for an SN75157D interface?
Termination should follow the topology and impedance of the selected EIA/TIA-422-B or EIA/TIA-423-B network rather than being added solely at the receiver. The SN75157D provides the differential input stage, while cable characteristic impedance and line topology determine whether a terminating resistor is appropriate. Review the relevant standard and manufacturer interface guidance, then validate common-mode voltage, skew, and noise margin in the finished system.
Where can I buy SN75157D online and what is the price?
Use the Request a Quote form on this page to request SN75157D availability, current commercial terms, and a quotation for the quantity you need. Pricing and inventory are maintained as live commercial data because they vary with order quantity, packaging format, and market conditions. The product page also provides a direct path to the manufacturer datasheet and the device's electrical characteristics.
What is the lead time for SN75157D?
Request the current lead time and minimum order quantity through the Request a Quote form on this page. Lead time depends on the selected package or shipping format, current manufacturer inventory, and order volume. The manufacturer product page confirms the SN75157 as an established device family, while transactional scheduling should be confirmed for the exact orderable MPN and destination.
What are the key specifications of SN75157D that engineers should know?
The SN75157D is a dual differential line receiver with two receiver channels, no transmitter channels, and a 5 V nominal supply. Key published ratings include a 4.75 V to 5.25 V operating range, a maximum signaling rate of 10 Mbit/s, TTL-compatible outputs, and an 0 °C to 70 °C operating range. It accepts differential or single-ended inputs and supports EIA/TIA-422-B, EIA/TIA-423-B, ITU V.10, and ITU V.11 interfaces.
What can replace SN75157D?
A replacement for the SN75157D must be a dual line receiver in the same 8-pin SOIC footprint with matching pin functions, a compatible 5 V supply range, and equivalent input thresholds and output timing. SN75156D is a closely related Texas Instruments receiver family member, but its suitability must be confirmed against its channel count and pin description. Package matching alone does not establish drop-in compatibility.

Données de référence d'ingénierie pour SN75157D — comparaison, recommandations de conception et informations de conformité.

Guide de sélection

Choose the SN75157D when the board needs two balanced or single-ended line-signal inputs and TTL-compatible logic outputs from a 5 V supply. Its SOIC-8 footprint, 10 Mbit/s maximum signaling rate, and support for EIA/TIA-422-B, EIA/TIA-423-B, ITU V.10, and ITU V.11 make it appropriate for industrial control, telemetry, instrumentation, and legacy data-acquisition interfaces. The 0 °C to 70 °C range requires qualification review for wider industrial environments. Consider SN75156D only after confirming its channel count, pin functions, supply range, input thresholds, and output timing against the SN75157D. Do not use a line driver, RS-232 transceiver, or single-channel receiver as a direct substitute without reassessing the complete interface.

Comparaison avec les alternatives

Paramètre Ce produit SN75156D
Brand Texas Instruments Texas Instruments
Package 8-SOIC (0.154", 3.90mm Width) 8-SOIC
Device Type Dual differential line receiver Line receiver

Principaux différenciateurs

  • Two independent receiver channels in one SOIC-8 device (vs SN75156D)
  • Documented differential and single-ended input flexibility (vs SN75156D)
  • Compatibility with established balanced-interface standards (vs SN75156D)

Notes de conception

Route each differential input as a closely matched pair and keep the pair away from switching-current paths. A common-mode voltage is present on a balanced line, so the useful signal is the voltage difference between the two conductors. Use a solid ground plane, avoid vias in the input path where practical, and apply protection or termination at the connector boundary only after checking how the selected interface topology affects signal amplitude.

Do not treat the SN75157D as an RS-232 device or as a line driver. It has two receiver channels and no transmitter channels, and its outputs are TTL-compatible rather than RS-232 voltage levels. Verify that the connected source supports the EIA/TIA-422-B, EIA/TIA-423-B, ITU V.10, or ITU V.11 receive requirements. Also check pin functions against the manufacturer pin-description table before revising an existing board.

Place the receiver close to the line connector so that the sensitive high-impedance inputs do not collect noise over a long PCB trace. Provide a stable 5 V rail with local high-frequency bypassing, keep the return path continuous, and maintain separation from unrelated analog or switching signals. The compact SOIC-8 footprint allows the two receiver channels to be placed near the connector while their TTL outputs route inward to the controller.

Informations de conformité

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Sans plomb
Unknown
Sans halogène
Unknown
Minerais de conflit
Unknown

The device is a commercial-temperature 0 °C to 70 °C interface IC. No explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations were identified in the manufacturer page, datasheet snippet, or distributor records used for this page.

Données vérifiées le : 2026-11-09 — données vérifiées et sélectionnées par l'équipe d'ingénierie composants de XAIPART

Recherches associées

SN75157D datasheet SN75157D datasheet pdf SN75157D pinout SN75157D specifications SN75157D equivalent SN75157D replacement SN75157D vs SN75156D SN75157D SOIC-8 pinout Texas Instruments SN75157D SN75157D RS-422 receiver SN75157D price SN75157D stock

Composants & termes associés

Texas Instruments SN75157D SN75157 SN75156D dual differential line receiver line receiver differential receiver single-ended receiver RS-422 RS-423 EIA/TIA-422-B EIA/TIA-423-B ITU V.10 ITU V.11 TTL-compatible output Schottky circuitry SOIC-8 package small-outline integrated circuit interface IC 5 V power supply 10 Mbit/s signaling rate industrial data acquisition telemetry interface process control
RFQ de devis rapide
Renseignez tous les détails — notre équipe commerciale vous répondra sous 24 heures
Référence Fabricant Boîtier QTY Prix cible Total
✓
Devis envoyé !

Nous répondrons à votre e-mail sous 24 heures

1
RFQ envoyée
2
Devis reçu
3
Commande passée
4
Paiement
5
Expédié
6
Livré
Voir les détails de la RFQ