Microchip Technology

SY88973VEY - 3.2Gbps CML Limiting Amplifier | Microchip

MPN: SY88973VEY ✓ সক্রিয়
+3.3 V ±10% Vdss 10-MSOP with exposed pad, 3.00 mm width Package
সর্বনিম্ন অর্ডার পরিমাণ: 1 |

SY88973VEY সারাংশ

The Microchip Technology SY88973VEY is a low-power limiting postamplifier for optical-network receivers, supporting data rates up to 3.2 Gbps while operating from a single +3.3 V ±10% or +5 V ±10% supply. It provides 38 dB differential gain, a 2 GHz 3 dB bandwidth, 50 Ω CML data outputs, 800 mVPP output swing, and a 10-lead MSOP package with an exposed pad.

A limiting postamplifier is a special-purpose high-speed amplifier stage that increases the amplitude of small electrical signals recovered from an optical receiver while shaping and limiting them into a digital output suitable for clock-and-data recovery, multiplexing, or other high-speed logic. In the device hierarchy, it belongs to the broader categories of amplifier IC, interface IC, signal-conditioning IC, and high-speed communication component.

The principal operating characteristics are multi-rate operation to 3.2 Gbps, 38 dB differential gain, and a 2 GHz 3 dB bandwidth. Its outputs are designed for CML inputs or AC-coupled PECL inputs, with 50 Ω CML data outputs and an output swing of 800 mVPP. Edge rates of 60 ps and typical random jitter of 5 ps RMS help preserve signal integrity in high-speed optical links. A TTL loss-of-signal function is also identified in the device description.

The SY88973V architecture combines wide bandwidth, high gain, and low noise in a compact surface-mount package. The 10-lead MSOP with exposed pad provides a practical thermal path on a PCB, while the single-supply operation supports both 3.3 V and 5 V system rails. The exposed-pad construction is particularly useful when the amplifier is operated continuously near its upper data-rate capability.

Typical uses include SONET optical-network receiver paths, optical-module signal conditioning, 3.2 Gbps backplane links, high-speed clock recovery front ends, and CML-to-PECL interface stages. The limiting function is appropriate when the receiver requires a consistent digital output amplitude from small, variable-amplitude input signals.

PCB implementation requires careful treatment of the exposed thermal pad, supply bypassing, high-speed differential routing, and output termination. Place the device close to the receiver or decision-circuit node to minimize trace loss, keep input and output return paths short, and use the manufacturer’s recommended resistor and capacitor values around the device.

This product page combines the manufacturer-device description with practical interface guidance, pin-package details, verified sourcing links, and a focused engineering comparison. It is designed to help engineers evaluate signal integrity, thermal handling, PCB implementation, and drop-in availability without relying on a generic distributor summary alone.

এর জন্য ড্রপ-ইন বিকল্প SY88973VEY — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।

এই পণ্যের জন্য কোনো ড্রপ-ইন বিকল্প পাওয়া যায়নি।

বিকল্প অনুরোধ করুন

SY88973VEY সর্বোচ্চ রেটিং ও বৈদ্যুতিক বৈশিষ্ট্য

Product Type Limiting postamplifier IC
Maximum Data Rate 3.2 Gbps
Minimum Amplified Signal Size 10 mVPP
Differential Gain 38 dB
3 dB Bandwidth 2 GHz
Low-Voltage Supply +3.3 V ±10%
High-Voltage Supply +5 V ±10%
অপারেটিং তাপমাত্রার পরিসর -40°C to +85°C
আউটপুট কনফিগারেশন 50 Ω CML data outputs
Output Swing 800 mVPP
Compatible Receiver Inputs CML inputs or AC-coupled PECL inputs
Edge Rate 60 ps
Typical Random Jitter 5 psRMS
Maximum Peak-to-Peak Jitter 15 psPP
প্যাকেজ 10-MSOP with exposed pad, 3.00 mm width
মাউন্টিং টাইপ Surface mount

SY88973VEY 10-msop with exposed pad, 3.00 mm width পিন কনফিগারেশন গাইড

SY88973VEY (10-msop with exposed pad, 3.00 mm width প্যাকেজ)-এর পিন কনফিগারেশন। এই অ্যানালগ কম্পোনেন্টে ইনপুট, আউটপুট ও পাওয়ার সাপ্লাই পিন রয়েছে। অফসেট নাল, কম্পেনসেশন ও এনেবল পিন কনফিগারেশনের জন্য প্রস্তুতকারকের ডেটাশিট দেখুন। সিগন্যাল কন্ডিশনিং ও অ্যামপ্লিফায়ার সার্কিটের জন্য আদর্শ।

SY88973VEY-এর জন্য 10-msop with exposed pad, 3.00 mm width প্যাকেজ পিনআউট ডায়াগ্রাম

এর জন্য বিস্তারিত পিনআউট ডেটা পাওয়া যায়নি SY88973VEY.

দেখুন ডেটাশিট সম্পূর্ণ পিন কনফিগারেশনের জন্য।

সাধারণ ব্যবহার

SY88973VEY এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: SONET Optical Receiver Signal Conditioning, CML-to-AC-Coupled-PECL Interface, 3.2 Gbps Backplane Receiver, Optical Module Receive Path, Clock-and-Data-Recovery Front End, High-Speed Instrumentation Signal Conditioning.

🌐

SONET Optical Receiver Signal Conditioning

The SY88973VEY fits the receiver-side limiting-amplifier stage of a high-speed SONET optical link because it supports operation to 3.2 Gbps, applies 38 dB of differential gain, and accepts signals as small as 10 mVPP. Its 50 Ω CML outputs with 800 mVPP swing can feed a clock-and-data-recovery decision device or downstream digital interface. The 2 GHz 3 dB bandwidth provides margin above the maximum supported data rate, while 60 ps edges and 5 psRMS typical random jitter help preserve timing margin. Layout the amplifier close to the photodetector or receiver front end to minimize loss and noise before amplification.

🔧

CML-to-AC-Coupled-PECL Interface

The SY88973VEY can bridge a high-speed CML-based receiver stage to an AC-coupled PECL interface because its outputs are specified as 50 Ω CML and its input signal range extends down to 10 mVPP. The 38 dB differential gain restores amplitude lost in optical or electrical channels, while the 800 mVPP output swing provides a usable signal level for the downstream comparator. A 3.3 V or 5 V single supply simplifies rail selection. The coupling network must preserve the required bias, impedance, and edge-rate behavior described in the manufacturer application circuit.

🖥️

3.2 Gbps Backplane Receiver

The SY88973VEY is appropriate for a 3.2 Gbps backplane receiver when the incoming differential signal is small and requires limiting before digital processing. Its 38 dB gain and 2 GHz 3 dB bandwidth give substantial amplification without narrowing the usable bandwidth near the target data rate. The 60 ps edge rate supports high-speed signaling, and 5 psRMS typical random jitter is valuable in a link with limited timing margin. Place the device near the receive connector or transceiver, maintain continuous reference planes, and use the recommended CML or AC-coupled PECL termination scheme.

🌐

Optical Module Receive Path

In a compact optical module, the SY88973VEY can condition a weak differential signal recovered from a photodiode or transimpedance stage before it reaches the module’s clock-and-data-recovery circuitry. The minimum 10 mVPP input capability and 38 dB gain help recover amplitude, while the limiting action produces a consistent digital signal. Its 10-lead MSOP exposed-pad package supports dense module layouts, and operation from either +3.3 V or +5 V accommodates common optical-module rails. Thermal-pad layout, via-in-pad use, bypass placement, and high-speed return-path control are especially important in compact module construction.

⏱️

Clock-and-Data-Recovery Front End

The SY88973VEY can serve as the analog gain-and-limiting stage immediately preceding a clock-and-data-recovery circuit in a 3.2 Gbps interface. A small receiver signal of 10 mVPP is increased by the device’s 38 dB differential gain, and the 800 mVPP CML output swing gives the downstream circuitry a defined signal level. Its 2 GHz 3 dB bandwidth accommodates the operating data rate, while the listed jitter characteristics help preserve timing performance. Keep the path between the amplifier and recovery device short and use controlled impedances to avoid additional reflections.

🔬

High-Speed Instrumentation Signal Conditioning

The SY88973VEY can be used in instrumentation that evaluates or regenerates differential signals operating at multi-gigabit rates. Its 38 dB gain and 2 GHz bandwidth make it useful when a small measured signal must be converted into a stable high-speed output, while the limiting function supports repeatable digital-level observations. The 3.3 V or 5 V supply range simplifies integration with mixed laboratory and embedded systems. Nevertheless, the amplifier is optimized for CML-family signaling rather than general-purpose analog measurement, so probe loading, jitter-sensitive routing, and differential impedance control require careful evaluation.

What is the SY88973VEY and what data rate does it support?
The SY88973VEY is a Microchip Technology low-power limiting postamplifier for high-speed optical receivers, with operation up to 3.2 Gbps. According to the manufacturer datasheet, it combines 38 dB differential gain, a 2 GHz 3 dB bandwidth, 50 Ω CML outputs, and an 800 mVPP output swing. The device accepts signals as small as 10 mVPP and is intended to condition signals for CML inputs or AC-coupled PECL inputs in optical-network and other high-speed communication systems.
What supply voltage does the SY88973VEY require?
The SY88973VEY operates from one supply rail at either +3.3 V ±10% or +5 V ±10%. According to the manufacturer datasheet, this single-supply operation allows the same limiting-amplifier circuit to interface with either 3.3 V or 5 V system rails. The 10-lead MSOP with exposed pad also provides a thermal path for continuous operation, although layout should preserve the recommended supply-bypass connections close to the device.
Where can I download the SY88973VEY datasheet PDF?
The SY88973VEY datasheet PDF is available through the technical-document link published on this page. The manufacturer datasheet identifies a 3.2 Gbps limiting postamplifier with 38 dB differential gain, a 2 GHz 3 dB bandwidth, a 3.3 V or 5 V supply, and an industrial temperature range of -40°C to +85°C. Use the pin-description table and recommended application circuit in that document when assigning PCB pins, selecting terminations, and placing bypass capacitors.
Where is the SY88973VEY pinout and what package does it use?
The SY88973VEY uses a 10-lead MSOP package with an exposed pad, and the manufacturer datasheet contains the authoritative pin-description table and footprint information. The package is a 3.00 mm-wide surface-mount construction. Use the exposed-pad thermal and electrical recommendations from the datasheet when assigning copper, and do not infer an exposed-pad connection solely from the package outline.
Can the SY88973VEY drive CML or PECL inputs?
Yes, the SY88973VEY is intended to amplify signals for CML inputs or AC-coupled PECL inputs. According to the manufacturer datasheet, its 50 Ω CML data outputs deliver 800 mVPP with 60 ps edge rates. AC coupling is important when the downstream PECL stage uses a different bias condition, while the CML output arrangement supports direct high-speed interface connections when its termination and common-mode requirements are satisfied.
What signal-integrity performance does the SY88973VEY provide?
The SY88973VEY provides a 38 dB differential gain, a 2 GHz 3 dB bandwidth, 60 ps edge rates, 5 psRMS typical random jitter, and up to 15 psPP jitter. According to the manufacturer datasheet, it can amplify signals as small as 10 mVPP to support data rates up to 3.2 Gbps. These characteristics make it suitable for receiver-side signal conditioning where low amplitude, jitter, and edge rate directly affect link-margin calculations.
What is the best drop-in replacement for the SY88973VEY?
A true drop-in replacement should use the same 10-lead MSOP exposed-pad footprint, preserve the pin assignments, and match the 3.2 Gbps bandwidth, 38 dB gain, supply range, and output characteristics. No independently verified cross-reference identifies a pin-compatible replacement with those published ratings. The tape-and-reel ordering code SY88973VEY-TR represents the same device variant rather than a different engineering alternative, so it should not be presented as a distinct drop-in replacement.
What can replace the SY88973VEY in an optical receiver design?
The closest functional choice must satisfy four electrical requirements: 3.3 V or 5 V single-supply operation, operation to 3.2 Gbps, approximately 38 dB differential gain, and compatibility with CML or AC-coupled PECL data paths. No verified same-package substitute with a complete published parameter set was identified. Before approving a replacement, compare pinout, gain-bandwidth product, output swing, jitter, loss-of-signal behavior, exposed-pad connection, and layout requirements rather than relying only on the stated data rate.
Is the SY88973VEY suitable for 3.2 Gbps SONET receiver designs?
The SY88973VEY is suitable for 3.2 Gbps optical-network receiver signal-conditioning stages because its specified maximum data rate is 3.2 Gbps and it provides 38 dB differential gain with a 2 GHz 3 dB bandwidth. According to the manufacturer datasheet, it handles signals as small as 10 mVPP and offers 50 Ω CML outputs with 800 mVPP swing. Final suitability still depends on the optical front-end output, required receive sensitivity, jitter budget, and clock-and-data-recovery architecture.
When should I choose the SY88973VEY over a general-purpose amplifier?
Choose the SY88973VEY when the design needs a dedicated receiver postamplifier rather than a general-purpose analog amplifier. Its purpose-built features include 3.2 Gbps multi-rate operation, 38 dB differential gain, 50 Ω CML outputs, 800 mVPP swing, and a TTL loss-of-signal function. A general-purpose amplifier would require more surrounding logic and may not provide the specified output impedance, slew behavior, jitter performance, or loss-of-signal integration.
How should the exposed pad on the SY88973VEY be handled during PCB layout?
Treat the exposed pad as both a thermal path and a package connection specified by the manufacturer datasheet, rather than treating it as an optional copper island. Provide a solderable land and controlled copper area beneath the package, connect it according to the recommended application circuit, and maintain thermal relief rules that meet the manufacturer’s assembly guidance. Good copper spreading improves heat removal from the exposed pad while minimizing assembly voiding risk.
Does the SY88973VEY require AC coupling for PECL interfaces?
Yes, the manufacturer describes the SY88973VEY as suitable for driving CML inputs or AC-coupled PECL inputs. The AC-coupled configuration allows the downstream PECL input bias to be established independently from the amplifier’s output conditions. Component values and routing should follow the manufacturer’s reference circuit, with the coupling capacitors placed close to the relevant device pins and transmission lines terminated consistently.
What are the key specifications of SY88973VEY that engineers should know?
The key SY88973VEY specifications are a 3.2 Gbps maximum data rate, 38 dB differential gain, 2 GHz 3 dB bandwidth, 50 Ω CML outputs, 800 mVPP output swing, and 60 ps edge rates. According to the manufacturer datasheet, the device accepts signals down to 10 mVPP, operates from +3.3 V ±10% or +5 V ±10%, and supports an industrial temperature range of -40°C to +85°C. Typical random jitter is 5 psRMS, with peak-to-peak jitter listed up to 15 psPP.
Where can I buy the SY88973VEY and what is its lead time?
Use the Request a Quote form on this page to request current availability, MOQ, and lead time for the SY88973VEY. The manufacturer-device information confirms the 10-MSOP exposed-pad configuration and identifies the part as a limiting postamplifier for optical networks. Stock and delivery schedules can change by quantity and purchasing context, so request the current commitment instead of relying on a historical listing status.
What is the price of the SY88973VEY?
Request a current quotation for the SY88973VEY through the Request a Quote form on this page. The structured commercial listing is designed to reflect quantity, package, and delivery requirements without inserting a stale unit figure into the technical description. For engineering budgeting, confirm the exact 10-MSOP exposed-pad ordering configuration, authorized supply status, quantity breaks, and expected delivery schedule through that form.
Is the SY88973VEY in stock?
The SY88973VEY is offered for quotation through the Request a Quote form on this page, where current stock can be checked for the requested quantity. Product availability may vary with order size, manufacturing allocation, and delivery timing. The device is identified by Microchip Technology as a limiting postamplifier IC in a 10-MSOP exposed-pad package for high-speed optical-network applications.

এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা SY88973VEY — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।

নির্বাচন গাইড

Choose the SY88973VEY when designing a 3.2 Gbps optical or high-speed digital receiver that needs dedicated limiting, 38 dB differential gain, CML outputs, and operation from either 3.3 V or 5 V. Its 2 GHz bandwidth, 60 ps edges, and low listed jitter make it more purposeful than a general-purpose amplifier in a compact receiver path. The TTL loss-of-signal function is useful when the system must monitor signal presence. Before approving any substitute, require the same exposed-pad MSOP footprint and pinout, closely matched gain-bandwidth and output characteristics, compatible supply behavior, and verified jitter performance. If no pin-compatible cross-reference can satisfy those constraints, retain the SY88973VEY and spend the design effort on correct terminations, exposed-pad assembly, and short controlled-impedance routing.

বিকল্পের সাথে তুলনা

পারামিটার এই পণ্য
Package 10-MSOP with exposed pad
Brand Microchip Technology
Product Type Limiting postamplifier IC
Maximum Data Rate 3.2 Gbps
Differential Gain 38 dB
3 dB Bandwidth 2 GHz
Supply Voltage +3.3 V ±10% or +5 V ±10%
Output Configuration 50 Ω CML
Output Swing 800 mVPP
Operating Temperature -40°C to +85°C
Minimum Input Signal 10 mVPP
Edge Rate 60 ps

মূল পার্থক্যসমূহ

  • Purpose-built receiver amplification (বনামGeneral-purpose amplifier)
  • Direct high-speed CML output capability (বনামAC-coupled PECL-only interface design)
  • Flexible single-rail supply operation (বনামFixed-rail amplifier option)

ডিজাইন নোট

Use the exposed pad as the principal thermal path for the 10-MSOP package. Provide the recommended solderable land beneath the pad, control thermal-via placement to balance conductivity and solderability, and connect the pad exactly as directed by the manufacturer datasheet. Good copper spreading limits junction-temperature rise during continuous 3.2 Gbps operation. Inspect assembled joints for voiding because excessive voids under an exposed pad can impair both heat transfer and mechanical reliability.

Keep the SY88973VEY close to the source of the small differential signal and avoid long stub branches between the device, terminations, and downstream receiver. Preserve continuous return paths under the high-speed pairs, use the manufacturer-recommended CML or AC-coupled PECL interface values, and place bypass capacitors close to the supply pins. Differential impedance and reference-plane discontinuities can otherwise degrade the useful edge rate and increase jitter beyond the nominal device characteristics.

Do not select a replacement solely because it is labeled a 3.2 Gbps limiting amplifier. Confirm the 10-lead MSOP pin assignments, exposed-pad connection, 3.3 V or 5 V supply behavior, output impedance and swing, gain-bandwidth product, jitter, loss-of-signal function, and termination requirements. Also distinguish SY88973VEY from the SY88973VEY-TR tape-and-reel ordering code: they are ordering representations of the same device family rather than distinct engineering alternatives.

কমপ্লায়েন্স তথ্য

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
লিড ফ্রি
Unknown
হ্যালোজেন ফ্রি
Unknown
কনফ্লিক্ট মিনারেলস
Unknown

No specific environmental or material-compliance declarations were included in the technical material for this device. The -40°C to +85°C industrial operating-temperature range does not by itself establish AEC-Q100 qualification.

ডেটা যাচাই করা হয়েছে: 2026-11-20 — ডেটা XAIPART-এর কম্পোনেন্ট ইঞ্জিনিয়ারিং টিম দ্বারা যাচাই ও কিউরেট করা হয়েছে

সম্পর্কিত অনুসন্ধান

SY88973VEY datasheet SY88973VEY datasheet pdf SY88973VEY pinout Microchip SY88973VEY SY88973VEY 3.2 Gbps SY88973VEY 38 dB gain SY88973VEY MSOP-10 SY88973VEY CML amplifier SY88973VEY equivalent SY88973VEY replacement SY88973VEY price SY88973VEY stock

সম্পর্কিত কম্পোনেন্ট ও শর্তাবলী

Microchip Technology SY88973VEY SY88973V SY88973VEY-TR limiting postamplifier special-purpose amplifier amplifier IC interface IC signal-conditioning IC CML PECL AC-coupled PECL TTL loss of signal 3.2 Gbps 38 dB differential gain 2 GHz 3 dB bandwidth 800 mVPP output swing 60 ps edge rate 5 psRMS random jitter 10-MSOP MSOP family surface-mount package exposed pad optical network receiver clock-and-data recovery
তাৎক্ষণিক বিলওয়াছে রেকোজিউইট
সম্পূর্ণ বিবরণ পূরণ করুন — আমাদের সেলস টিম 24 ঘণ্টার মধ্যে উত্তর দেবে
পার্ট নম্বর উৎপাদক প্যাকেজ QTY লক্ষ্যমূল্য প্রসারিত
✓
বিল প্রস্তুত করা হয়েছে!

আমরা ২৪ ঘণ্টার মধ্যে আপনার ইমেইলে প্রত্যুত্তর দেব

1
RFQ জমা হয়েছে
2
কোটেশন পাওয়া গেছে
3
অর্ডার দেওয়া হয়েছে
4
পেমেন্ট
5
শিপ করা হয়েছে
6
ডেলিভারি হয়েছে
RFQ বিবরণ দেখুন