Texas Instruments

THS4061ID - 180MHz High-Output-Drive Op Amp | Texas Instruments

MPN: THS4061ID ✓ সক্রিয়
115 mA Id 8-pin SOIC (D) Package
সর্বনিম্ন অর্ডার পরিমাণ: 1 |

THS4061ID সারাংশ

The Texas Instruments THS4061ID is a single-circuit, 180 MHz high-output-drive voltage-feedback operational amplifier packaged in an 8-pin SOIC. Its headline specifications are 180 MHz small-signal bandwidth, 400 V/µs slew rate, and 40 ns settling time to 0.1%, making it suitable for high-speed signal conditioning, video, communications, and imaging systems. The amplifier also provides typical output-drive current of 115 mA.

A voltage-feedback operational amplifier is a gain-control device that uses feedback to set closed-loop gain while maintaining signal fidelity. The THS4061 belongs to the broader operational-amplifier hierarchy, which includes general-purpose amplifiers, high-speed amplifiers, instrumentation amplifiers, and power-management-support functions within analog and mixed-signal semiconductors. The THS4061 is optimized for applications requiring wide bandwidth, rapid output transitions, and the ability to drive downstream loads.

Key features include stable operation at all closed-loop gains in both inverting and noninverting configurations. Its 180 MHz bandwidth supports high-frequency signal paths, while the 400 V/µs slew rate allows large voltage changes to occur rapidly. The 40 ns settling time to 0.1% is particularly useful in data-acquisition and waveform-generation systems where accurate return to the final level is important after a step input.

The device is designed for high-output-drive operation, with 115 mA typical output current. This capability allows the amplifier to drive moderate loading while retaining low distortion. Its video performance includes a 75 MHz bandwidth at 0.1 dB differential gain, 0.02% differential gain error, and 0.02° differential phase, supporting video-line and composite-video signal conditioning where gain and phase consistency are critical.

Typical applications include video routing and distribution, communications-interface signal conditioning, imaging systems, test and measurement equipment, and general-purpose high-speed analog amplification. In each case, the design should account for the selected gain, output-load impedance, PCB layout, supply bypassing, and the need to preserve the amplifier's bandwidth and settling performance.

A critical design consideration is PCB symmetry around the amplifier. Short, direct feedback paths, closely matched high-frequency routing, solid ground-plane continuity, and local supply decoupling reduce parasitic feedback and distortion. The input and output should also be isolated from clocked or switching circuitry because 180 MHz bandwidth can amplify unwanted high-frequency noise and coupling.

This product page consolidates the Texas Instruments product information, exact 180 MHz bandwidth, 400 V/µs slew-rate, 40 ns settling-time, and high-output-drive characteristics into an engineering-focused reference. It also identifies the same-package THS4061CDR alternative and provides selection and design guidance for video, communications, imaging, and precision high-speed analog applications.

এর জন্য ড্রপ-ইন বিকল্প THS4061ID — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।

এই সিরিজের ভ্যারিয়েন্ট

একই সিরিজের মডেল যেগুলো drop-in compatible THS4061ID (একই form factor এবং footprint) — পার্থক্য রয়েছে Amplifier Type, Package, Small-Signal Bandwidth.

Texas Instruments
Amplifier Type: Single voltage-feedback operational amplifier
Package: 8-SOIC (D), 0.154 inch (3.90 mm) width
Small-Signal Bandwidth: 180 MHz (-3 dB)
এর সাথে তুলনা করুন THS4061ID →

THS4061CDR

✅ ড্রপ-ইন
📦 8-pin SOIC (D)
Same THS4061 family and 8-pin SOIC footprint; the orderable grade and tape-and-reel delivery configuration differ, with exact temperature limits requiring confirmation.

📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)

THS4061ID সর্বোচ্চ রেটিং ও বৈদ্যুতিক বৈশিষ্ট্য

Amplifier Type Voltage-feedback operational amplifier
Number of Circuits 1 circuit
Small-Signal Bandwidth 180 MHz
Slew Rate 400 V/µs
Settling Time 40 ns to 0.1%
Typical Output Drive Current 115 mA
Video 0.1 dB Bandwidth 75 MHz
Differential Gain Error 0.02%
Differential Phase 0.02°
Gain at Which Video Performance Is Specified 5
Stability Configuration Stable at all gains in inverting and noninverting configurations
প্যাকেজ 8-pin SOIC (D)
মাউন্টিং টাইপ Surface mount

THS4061ID 8-pin soic (d) পিন কনফিগারেশন গাইড

THS4061ID (8-pin soic (d) প্যাকেজ)-এর পিন কনফিগারেশন। এই অ্যানালগ কম্পোনেন্টে ইনপুট, আউটপুট ও পাওয়ার সাপ্লাই পিন রয়েছে। অফসেট নাল, কম্পেনসেশন ও এনেবল পিন কনফিগারেশনের জন্য প্রস্তুতকারকের ডেটাশিট দেখুন। সিগন্যাল কন্ডিশনিং ও অ্যামপ্লিফায়ার সার্কিটের জন্য আদর্শ।

THS4061ID-এর জন্য 8-pin soic (d) প্যাকেজ পিনআউট ডায়াগ্রাম

এর জন্য বিস্তারিত পিনআউট ডেটা পাওয়া যায়নি THS4061ID.

দেখুন ডেটাশিট সম্পূর্ণ পিন কনফিগারেশনের জন্য।

সাধারণ ব্যবহার

THS4061ID এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Video Signal Conditioning, Communications Front End, Imaging Signal Chain, Data Acquisition Front End, Test and Measurement Equipment, Industrial Sensor Interfacing.

📺

Video Signal Conditioning

The THS4061ID fits video buffering and active-cable applications because its 180 MHz small-signal bandwidth supports wideband signal propagation, while 400 V/µs slew rate provides fast edge handling. The manufacturer datasheet specifies 75 MHz bandwidth at 0.1 dB differential gain, 0.02% differential gain error, and 0.02° differential phase at a gain of 5, which are useful indicators for color and composite-video fidelity. Its typical 115 mA output-drive capability helps drive downstream video stages, although cable loading, DC coupling, and output swing should be verified against the application. Keep the feedback loop compact and provide local supply bypassing to preserve gain and phase performance.

🌐

Communications Front End

The THS4061ID is suitable for communications signal conditioning where a low-impedance receiver or driver must be fed from a higher-impedance source. Its 180 MHz bandwidth handles high-frequency modulation components, and the 400 V/µs slew rate supports rapid amplitude and phase transitions without the severe slew limitation of low-bandwidth amplifiers. The 115 mA typical output-drive current provides additional drive margin for moderate loading. For an RF-adjacent or communications interface, engineers should still evaluate input common-mode range, output swing, noise, and channel bandwidth. Short traces, a continuous reference plane, and symmetric feedback routing are essential because high open-loop gain can amplify small layout asymmetries.

📷

Imaging Signal Chain

The THS4061ID can amplify the high-bandwidth signals found in imaging and photodetector interface circuits when rapid settling and strong output drive are important. Its 180 MHz bandwidth follows the signal content, while 40 ns settling to 0.1% supports deterministic measurement or sampling windows after a transition. The 400 V/µs slew rate and 115 mA typical drive allow the amplifier to operate ahead of slower general-purpose devices. Design the input stage to limit noise and capacitance, because excessive input capacitance can reduce stability and alter the achieved bandwidth. Place the amplifier and its feedback network close to the sensor interface, maintain balanced routing, and use a dedicated return path to minimize image-dependent distortion.

📊

Data Acquisition Front End

The THS4061ID is appropriate for high-speed data-acquisition front ends that require rapid step response and repeatable settling. According to the Texas Instruments datasheet, the amplifier provides 40 ns settling time to 0.1% and remains stable at all closed-loop gains in both inverting and noninverting configurations. That combination simplifies the selection of a feedback network when conditioning signals before an ADC. The 180 MHz bandwidth must be coordinated with the ADC sample rate and anti-alias filter, while the 400 V/µs slew rate should cover the converter's required input excursions. Keep the source impedance and feedback resistor values within the manufacturer's guidance and avoid adding long breakout traces between the amplifier and sampling device.

🖥️

Test and Measurement Equipment

The THS4061ID can serve as a high-speed buffer, driver, or gain stage in oscilloscope, arbitrary-function, and waveform-measurement equipment. Its 180 MHz bandwidth, 400 V/µs slew rate, and 115 mA typical output-drive current provide the speed and load capability expected in a general-purpose high-speed amplifier. The 40 ns settling time to 0.1% is useful when the instrument must return quickly to an accurate baseline following a transition. When driving cables or probe networks, observe the datasheet output-current and stability limits because capacitive loading can alter transient behavior. Use short, symmetric layout, provide local bypass capacitors, and avoid sharing a long ground path between sensitive input and output stages.

🏭

Industrial Sensor Interfacing

The THS4061ID can condition fast industrial sensor outputs when the interface bandwidth exceeds the capability of a general-purpose op amp. Its 180 MHz bandwidth supports high-frequency sensor signals, and the 400 V/µs slew rate preserves rapid transitions through subsequent circuitry. The amplifier's 115 mA typical output-drive capability is useful for driving downstream instrumentation stages or short cable connections. Industrial designs must still verify supply range, input common-mode limits, noise, and temperature grade for the exact orderable device. Isolation barriers, protection networks, and long cables can introduce capacitance and transient hazards; account for those effects in stability analysis and keep the high-speed feedback loop isolated from protection-node return currents.

সুপারিশকৃত পণ্যের সারসংক্ষেপ

THS4062 Dual-channel THS4061-family alternative for dual video paths ব্যবহৃত হয়: Video Signal Conditioning, Communications Front End, Imaging Signal Chain, Data Acquisition Front End, Test and Measurement Equipment, Industrial Sensor Interfacing
What is the THS4061ID?
The THS4061ID is a single-channel, 180 MHz high-output-drive voltage-feedback operational amplifier from Texas Instruments. According to the Texas Instruments product page and manufacturer datasheet, it combines 400 V/µs slew rate, 40 ns settling time to 0.1%, and typical 115 mA output-drive current. The device is offered in an 8-pin SOIC package for high-speed video, communications, imaging, and general-purpose analog signal-conditioning circuits.
What are the key specifications of THS4061ID that engineers should know?
The key THS4061ID specifications are 180 MHz bandwidth, 400 V/µs slew rate, 40 ns settling time to 0.1%, and 115 mA typical output-drive current. According to the Texas Instruments manufacturer datasheet, the amplifier is stable at all closed-loop gains in both inverting and noninverting configurations. It also provides 75 MHz bandwidth at 0.1 dB differential gain, 0.02% differential gain error, and 0.02° differential phase.
Where can I download the THS4061ID datasheet PDF?
The official THS4061ID datasheet is available through the Texas Instruments technical document link on this page. It is the appropriate source for the complete electrical characteristics, pin descriptions, recommended operating conditions, typical performance curves, and application guidance. Use the manufacturer document rather than a mirror when determining pin functions or design limits for a production design.
Where can I find the THS4061ID pinout?
Use the pin-description table and package drawing in the Texas Instruments THS4061 manufacturer datasheet to identify every connection on the 8-pin SOIC. The product page confirms an 8-pin SOIC package, while the complete numbered pin list and exposed thermal requirements must be taken from the package diagram. Do not infer unused or supply-pin functions from another amplifier in the same family.
Is the THS4061ID suitable for video applications?
Yes, the THS4061ID is suitable for video signal conditioning because its manufacturer datasheet specifies 75 MHz bandwidth at 0.1 dB differential gain, 0.02% differential gain error, and 0.02° differential phase. The 180 MHz small-signal bandwidth and 400 V/µs slew rate also help preserve transitions and support routing through practical cable and board loads.
Can the THS4061ID drive a low-impedance load?
The THS4061ID provides high output-drive capability, with 115 mA typical output-drive current according to the Texas Instruments datasheet. That makes it more suitable for moderate loading than a general-purpose low-power op amp. The exact load and output-voltage swing must still be checked against the datasheet output-current and output-voltage limits before use.
What is the difference between THS4061ID and THS4061CDR?
THS4061ID and THS4061CDR belong to the same THS4061 family and use an 8-pin SOIC package, but their orderable temperature grades and delivery configurations can differ. The comparison data identifies THS4061CDR as the closest same-family alternative. Confirm the grade markings, temperature range, supply limits, and reel configuration in the manufacturer ordering information before substitution.
THS4061ID vs THS4061CDR: which is better for an industrial design?
Choose THS4061ID or THS4061CDR according to the required temperature grade and production packaging rather than basic AC performance, because both are THS4061-family devices with 180 MHz-class bandwidth and the same SOIC footprint. For an industrial application, verify the exact operating-temperature grade shown in the Texas Instruments part details. The available cross-reference information does not establish every grade-specific parameter.
When should I choose the THS4061ID instead of a general-purpose op amp?
Choose the THS4061ID when the signal path needs substantially more bandwidth and slew rate than a general-purpose amplifier provides. Its 180 MHz bandwidth, 400 V/µs slew rate, and 115 mA typical output drive make it appropriate for video, communications, imaging, and high-speed test circuits. A general-purpose op amp may be preferable only when its lower bandwidth and drive requirements are sufficient.
Is the THS4061ID suitable for high-speed instrumentation?
The THS4061ID can suit high-speed instrumentation when the required bandwidth, settling time, and output drive fit its 180 MHz bandwidth, 40 ns 0.1% settling time, and 115 mA typical drive specifications. Its stability across all closed-loop gains simplifies topology selection. Input noise, offset, common-mode range, and precision performance must be checked separately for the specific measurement accuracy.
What can replace the THS4061ID?
The THS4061CDR is the verified same-family alternative with the same 8-pin SOIC package, making it the closest candidate for a drop-in review. Confirm pin functions, temperature grade, electrical limits, and supply compatibility against the manufacturer datasheet. The cross-reference search returned no additional supported alternatives, so an unverified amplifier should not be treated as a direct replacement.
Can THS4061CDR replace THS4061ID without a PCB change?
THS4061CDR can be evaluated as a no-PCB-change replacement because it uses the same 8-pin SOIC package as THS4061ID. Before substitution, verify that the gain configuration, supply voltage, input and output ranges, stability, and temperature requirements match. Package equivalence alone does not guarantee identical qualification or production behavior.
Where can I buy THS4061ID and check its current lead time?
Use the Request a Quote form on this page to request current THS4061ID availability, lead time, and order quantities. The commercial team can confirm the appropriate SOIC configuration and any available lot or traceability requirements. Do not rely on a cached listing snapshot when production scheduling depends on a current commitment.
What is the current price of THS4061ID?
The current THS4061ID price is handled through the Request a Quote form on this page because commercial terms and supply can change by order quantity, date, and configuration. Submit the required quantity and target package details for a current quotation. This avoids presenting a stale figure that may not correspond to the requested production lot.
Is THS4061ID in stock?
Submit the requested quantity and timing through the Request a Quote form on this page to obtain the current THS4061ID stock and lead-time position. A distributor result appearing in search does not by itself establish available inventory for a specific order. The quotation response provides the relevant allocation and schedule for the request.

এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা THS4061ID — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।

নির্বাচন গাইড

Choose the THS4061ID when the design requires a single amplifier combining 180 MHz bandwidth, 400 V/µs slew rate, 40 ns settling to 0.1%, and 115 mA typical output drive. It is well suited to video buffers, communications interfaces, imaging circuits, high-speed acquisition front ends, and test equipment. Consider a lower-bandwidth amplifier when energy, noise, or cost dominate and the required signal bandwidth is modest. THS4061CDR is the closest same-package same-family alternative when its orderable temperature grade and delivery configuration meet the design; verify the exact grade and electrical limits before substitution. For two related high-speed channels, a dual amplifier may simplify board planning, but it is not automatically a pin-compatible replacement for this single-channel device. Final selection must also confirm supply range, input and output limits, load behavior, operating temperature, and PCB compatibility.

বিকল্পের সাথে তুলনা

পারামিটার এই পণ্য THS4061CDR
Package 8-pin SOIC (D) 8-pin SOIC (D)
Brand Texas Instruments Texas Instruments
Amplifier Configuration Single operational amplifier Single operational amplifier
Small-Signal Bandwidth 180 MHz 180 MHz family specification
Slew Rate 400 V/µs 400 V/µs family specification
Settling Time 40 ns to 0.1% 40 ns to 0.1% family specification
Typical Output Drive Current 115 mA 115 mA family specification
Video 0.1 dB Bandwidth 75 MHz at gain 5 75 MHz at gain 5 family specification
Differential Gain Error 0.02% 0.02% family specification
Differential Phase 0.02° 0.02° family specification

মূল পার্থক্যসমূহ

  • Combines wide bandwidth with unusually high output-drive capability (বনামGeneral-purpose single operational amplifiers)
  • Video performance is characterized at a useful operating gain (বনামGeneral-purpose single operational amplifiers)
  • Provides fast deterministic settling (বনামLower-bandwidth precision amplifiers)

ডিজাইন নোট

Place input, output, feedback, and supply-connection components close to the THS4061ID. Keep the feedback loop compact and avoid routing output traces beneath the input or feedback paths. Use a continuous ground plane where practical, and place local bypass capacitors at the device supply pins. The amplifier's 180 MHz bandwidth makes small parasitic inductance and loop area significant, so symmetric routing is more important than merely shortening the power trace.

Evaluate every intended output load for capacitive and inductive reactance. The 115 mA typical output-drive current does not guarantee stability with arbitrary loading. If driving a cable, connector, ADC input, or long trace, use the manufacturer stability and output-current guidance, keep the trace short, and add an appropriate isolation resistor or termination method when required. Validate the complete board rather than relying only on simulation of the amplifier.

Do not select the THS4061ID solely by its 180 MHz bandwidth. Confirm supply voltage, input common-mode range, output swing, offset, noise, operating temperature, and load current against the manufacturer datasheet. The 400 V/µs slew rate must also be compatible with the downstream device and system bandwidth. These checks prevent a fast amplifier from operating outside its valid electrical limits or creating excessive overshoot and ringing.

Keep analog input and output paths away from clocks, switching regulators, and high-current return paths. If isolation is impossible, orient the amplifier so current from the noisy subsystem does not flow through the reference ground used by its input pair. Maintain matched geometry around the signal path and avoid asymmetrical stubs. Because the THS4061ID is stable at all closed-loop gains, stability is less likely to be an issue at a valid gain, but layout parasitics can still degrade phase margin and transient response.

কমপ্লায়েন্স তথ্য

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
লিড ফ্রি
Unknown
হ্যালোজেন ফ্রি
Unknown
কনফ্লিক্ট মিনারেলস
Unknown

No product-specific environmental or material-compliance declarations are stated in the cited product results. Confirm these attributes from the Texas Instruments product page or manufacturer documentation before procurement.

ডেটা যাচাই করা হয়েছে: 2026-11-10 — ডেটা XAIPART-এর কম্পোনেন্ট ইঞ্জিনিয়ারিং টিম দ্বারা যাচাই ও কিউরেট করা হয়েছে

সম্পর্কিত অনুসন্ধান

THS4061ID datasheet THS4061ID pinout THS4061ID datasheet pdf THS4061ID equivalent THS4061ID replacement THS4061ID vs THS4061CDR THS4061ID footprint THS4061ID spice model THS4061ID price THS4061ID stock Texas Instruments THS4061ID THS4061 180MHz SOIC-8 THS4061 video amplifier THS4061 high speed op amp

সম্পর্কিত কম্পোনেন্ট ও শর্তাবলী

Texas Instruments THS4061ID THS4061CDR THS4061 THS4062 operational amplifier voltage-feedback amplifier high-speed amplifier single-channel amplifier analog semiconductor small-signal bandwidth slew rate settling time output-drive current differential gain error differential phase video bandwidth inverting configuration noninverting configuration 8-pin SOIC surface-mount package signal conditioning video communications imaging data acquisition test and measurement
তাৎক্ষণিক বিলওয়াছে রেকোজিউইট
সম্পূর্ণ বিবরণ পূরণ করুন — আমাদের সেলস টিম 24 ঘণ্টার মধ্যে উত্তর দেবে
পার্ট নম্বর উৎপাদক প্যাকেজ QTY লক্ষ্যমূল্য প্রসারিত
✓
বিল প্রস্তুত করা হয়েছে!

আমরা ২৪ ঘণ্টার মধ্যে আপনার ইমেইলে প্রত্যুত্তর দেব

1
RFQ জমা হয়েছে
2
কোটেশন পাওয়া গেছে
3
অর্ডার দেওয়া হয়েছে
4
পেমেন্ট
5
শিপ করা হয়েছে
6
ডেলিভারি হয়েছে
RFQ বিবরণ দেখুন