THS4061ID - 180MHz High-Output-Drive Op Amp | Texas Instruments
N.º de pieza: THS4061ID ✓ ActivoTHS4061ID Descripción general
A voltage-feedback operational amplifier is a gain-control device that uses feedback to set closed-loop gain while maintaining signal fidelity. The THS4061 belongs to the broader operational-amplifier hierarchy, which includes general-purpose amplifiers, high-speed amplifiers, instrumentation amplifiers, and power-management-support functions within analog and mixed-signal semiconductors. The THS4061 is optimized for applications requiring wide bandwidth, rapid output transitions, and the ability to drive downstream loads.
Key features include stable operation at all closed-loop gains in both inverting and noninverting configurations. Its 180 MHz bandwidth supports high-frequency signal paths, while the 400 V/µs slew rate allows large voltage changes to occur rapidly. The 40 ns settling time to 0.1% is particularly useful in data-acquisition and waveform-generation systems where accurate return to the final level is important after a step input.
The device is designed for high-output-drive operation, with 115 mA typical output current. This capability allows the amplifier to drive moderate loading while retaining low distortion. Its video performance includes a 75 MHz bandwidth at 0.1 dB differential gain, 0.02% differential gain error, and 0.02° differential phase, supporting video-line and composite-video signal conditioning where gain and phase consistency are critical.
Typical applications include video routing and distribution, communications-interface signal conditioning, imaging systems, test and measurement equipment, and general-purpose high-speed analog amplification. In each case, the design should account for the selected gain, output-load impedance, PCB layout, supply bypassing, and the need to preserve the amplifier's bandwidth and settling performance.
A critical design consideration is PCB symmetry around the amplifier. Short, direct feedback paths, closely matched high-frequency routing, solid ground-plane continuity, and local supply decoupling reduce parasitic feedback and distortion. The input and output should also be isolated from clocked or switching circuitry because 180 MHz bandwidth can amplify unwanted high-frequency noise and coupling.
This product page consolidates the Texas Instruments product information, exact 180 MHz bandwidth, 400 V/µs slew-rate, 40 ns settling-time, and high-output-drive characteristics into an engineering-focused reference. It also identifies the same-package THS4061CDR alternative and provides selection and design guidance for video, communications, imaging, and precision high-speed analog applications.
Alternativas directas para THS4061ID — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con THS4061ID (mismo factor de forma y huella) — difiere en Amplifier Type, Package, Small-Signal Bandwidth.
THS4061CDR
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
THS4061ID Valores máximos y características eléctricas
| Amplifier Type | Voltage-feedback operational amplifier |
| Number of Circuits | 1 circuit |
| Small-Signal Bandwidth | 180 MHz |
| Slew Rate | 400 V/µs |
| Settling Time | 40 ns to 0.1% |
| Typical Output Drive Current | 115 mA |
| Video 0.1 dB Bandwidth | 75 MHz |
| Differential Gain Error | 0.02% |
| Differential Phase | 0.02° |
| Gain at Which Video Performance Is Specified | 5 |
| Stability Configuration | Stable at all gains in inverting and noninverting configurations |
| Encapsulado | 8-pin SOIC (D) |
| Tipo de montaje | Surface mount |
Guía de configuración de pines de THS4061ID 8-pin soic (d)
Configuración de pines para THS4061ID (encapsulado 8-pin soic (d)). Este componente analógico presenta pines de entrada, salida y alimentación. Consulte la hoja de datos del fabricante para conocer las configuraciones de los pines de ajuste de offset, compensación y habilitación. Ideal para circuitos de acondicionamiento de señal y amplificadores.
No hay datos detallados de patillaje disponibles para THS4061ID.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
THS4061ID es adecuado para 6 aplicacións: Video Signal Conditioning, Communications Front End, Imaging Signal Chain, Data Acquisition Front End, Test and Measurement Equipment, Industrial Sensor Interfacing.
Video Signal Conditioning
The THS4061ID fits video buffering and active-cable applications because its 180 MHz small-signal bandwidth supports wideband signal propagation, while 400 V/µs slew rate provides fast edge handling. The manufacturer datasheet specifies 75 MHz bandwidth at 0.1 dB differential gain, 0.02% differential gain error, and 0.02° differential phase at a gain of 5, which are useful indicators for color and composite-video fidelity. Its typical 115 mA output-drive capability helps drive downstream video stages, although cable loading, DC coupling, and output swing should be verified against the application. Keep the feedback loop compact and provide local supply bypassing to preserve gain and phase performance.
Recomendado
Communications Front End
The THS4061ID is suitable for communications signal conditioning where a low-impedance receiver or driver must be fed from a higher-impedance source. Its 180 MHz bandwidth handles high-frequency modulation components, and the 400 V/µs slew rate supports rapid amplitude and phase transitions without the severe slew limitation of low-bandwidth amplifiers. The 115 mA typical output-drive current provides additional drive margin for moderate loading. For an RF-adjacent or communications interface, engineers should still evaluate input common-mode range, output swing, noise, and channel bandwidth. Short traces, a continuous reference plane, and symmetric feedback routing are essential because high open-loop gain can amplify small layout asymmetries.
Recomendado
Imaging Signal Chain
The THS4061ID can amplify the high-bandwidth signals found in imaging and photodetector interface circuits when rapid settling and strong output drive are important. Its 180 MHz bandwidth follows the signal content, while 40 ns settling to 0.1% supports deterministic measurement or sampling windows after a transition. The 400 V/µs slew rate and 115 mA typical drive allow the amplifier to operate ahead of slower general-purpose devices. Design the input stage to limit noise and capacitance, because excessive input capacitance can reduce stability and alter the achieved bandwidth. Place the amplifier and its feedback network close to the sensor interface, maintain balanced routing, and use a dedicated return path to minimize image-dependent distortion.
Recomendado
Data Acquisition Front End
The THS4061ID is appropriate for high-speed data-acquisition front ends that require rapid step response and repeatable settling. According to the Texas Instruments datasheet, the amplifier provides 40 ns settling time to 0.1% and remains stable at all closed-loop gains in both inverting and noninverting configurations. That combination simplifies the selection of a feedback network when conditioning signals before an ADC. The 180 MHz bandwidth must be coordinated with the ADC sample rate and anti-alias filter, while the 400 V/µs slew rate should cover the converter's required input excursions. Keep the source impedance and feedback resistor values within the manufacturer's guidance and avoid adding long breakout traces between the amplifier and sampling device.
Recomendado
Test and Measurement Equipment
The THS4061ID can serve as a high-speed buffer, driver, or gain stage in oscilloscope, arbitrary-function, and waveform-measurement equipment. Its 180 MHz bandwidth, 400 V/µs slew rate, and 115 mA typical output-drive current provide the speed and load capability expected in a general-purpose high-speed amplifier. The 40 ns settling time to 0.1% is useful when the instrument must return quickly to an accurate baseline following a transition. When driving cables or probe networks, observe the datasheet output-current and stability limits because capacitive loading can alter transient behavior. Use short, symmetric layout, provide local bypass capacitors, and avoid sharing a long ground path between sensitive input and output stages.
Recomendado
Industrial Sensor Interfacing
The THS4061ID can condition fast industrial sensor outputs when the interface bandwidth exceeds the capability of a general-purpose op amp. Its 180 MHz bandwidth supports high-frequency sensor signals, and the 400 V/µs slew rate preserves rapid transitions through subsequent circuitry. The amplifier's 115 mA typical output-drive capability is useful for driving downstream instrumentation stages or short cable connections. Industrial designs must still verify supply range, input common-mode limits, noise, and temperature grade for the exact orderable device. Isolation barriers, protection networks, and long cables can introduce capacitance and transient hazards; account for those effects in stability analysis and keep the high-speed feedback loop isolated from protection-node return currents.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para THS4061ID — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | THS4061CDR |
|---|---|---|
| Package | 8-pin SOIC (D) | 8-pin SOIC (D) |
| Brand | Texas Instruments | Texas Instruments |
| Amplifier Configuration | Single operational amplifier | Single operational amplifier |
| Small-Signal Bandwidth | 180 MHz | 180 MHz family specification |
| Slew Rate | 400 V/µs | 400 V/µs family specification |
| Settling Time | 40 ns to 0.1% | 40 ns to 0.1% family specification |
| Typical Output Drive Current | 115 mA | 115 mA family specification |
| Video 0.1 dB Bandwidth | 75 MHz at gain 5 | 75 MHz at gain 5 family specification |
| Differential Gain Error | 0.02% | 0.02% family specification |
| Differential Phase | 0.02° | 0.02° family specification |
Diferenciadores clave
- Combines wide bandwidth with unusually high output-drive capability (frente a General-purpose single operational amplifiers)
- Video performance is characterized at a useful operating gain (frente a General-purpose single operational amplifiers)
- Provides fast deterministic settling (frente a Lower-bandwidth precision amplifiers)
Notas de diseño
Place input, output, feedback, and supply-connection components close to the THS4061ID. Keep the feedback loop compact and avoid routing output traces beneath the input or feedback paths. Use a continuous ground plane where practical, and place local bypass capacitors at the device supply pins. The amplifier's 180 MHz bandwidth makes small parasitic inductance and loop area significant, so symmetric routing is more important than merely shortening the power trace.
Evaluate every intended output load for capacitive and inductive reactance. The 115 mA typical output-drive current does not guarantee stability with arbitrary loading. If driving a cable, connector, ADC input, or long trace, use the manufacturer stability and output-current guidance, keep the trace short, and add an appropriate isolation resistor or termination method when required. Validate the complete board rather than relying only on simulation of the amplifier.
Do not select the THS4061ID solely by its 180 MHz bandwidth. Confirm supply voltage, input common-mode range, output swing, offset, noise, operating temperature, and load current against the manufacturer datasheet. The 400 V/µs slew rate must also be compatible with the downstream device and system bandwidth. These checks prevent a fast amplifier from operating outside its valid electrical limits or creating excessive overshoot and ringing.
Keep analog input and output paths away from clocks, switching regulators, and high-current return paths. If isolation is impossible, orient the amplifier so current from the noisy subsystem does not flow through the reference ground used by its input pair. Maintain matched geometry around the signal path and avoid asymmetrical stubs. Because the THS4061ID is stable at all closed-loop gains, stability is less likely to be an issue at a valid gain, but layout parasitics can still degrade phase margin and transient response.
Información de cumplimiento
No product-specific environmental or material-compliance declarations are stated in the cited product results. Confirm these attributes from the Texas Instruments product page or manufacturer documentation before procurement.