NXP Semiconductors

TJA1028TK/5V0/20:1 - LIN Transceiver with 5V Regulator | NXP

MPN: TJA1028TK/5V0/20:1 ✓ সক্রিয়
4.5 mA Vdss 70 mA Id 8-HVSON (3 x 3 mm) with exposed pad Package
সর্বনিম্ন অর্ডার পরিমাণ: 1 |

TJA1028TK/5V0/20:1 সারাংশ

The NXP Semiconductors TJA1028TK/5V0/20:1 is a LIN 2.0, LIN 2.1, SAE J2602, and ISO 17987-4:2016 compliant half-duplex transceiver with an integrated low-dropout 5.0 V voltage regulator, a maximum regulated output current of 70 mA, and a 20 kbit/s version designation. It is packaged in an 8-HVSON surface-mount package with a 3 x 3 mm footprint and exposed pad. The integrated regulator supplies local electronics while the transceiver connects the node to a LIN bus.

A LIN, or Local Interconnect Network, transceiver is an interface IC that converts logic-level signals between a host controller and a low-cost, single-wire automotive communication bus. LIN belongs to the broader vehicle network-interface hierarchy, where transceivers add the electrical protection and signal conditioning required to communicate reliably over a physically long, noisy harness. The TJA1028 combines this bus-interface role with a local power-supply function, reducing the component count needed by compact LIN nodes.

The device provides a 5.0 V regulator variant with a stated output range of 4.9 V to 5.1 V. The regulator can deliver up to 70 mA, while the listed supply current is 4.5 mA. The /20 version is associated with a 20 kbit/s LIN communication class. NXP also lists operation from -40 degrees C to +150 degrees C, making the device suitable for demanding automotive environments. The package is identified as 8-HVSON (3 x 3 mm), and the exposed pad supports heat dissipation into the PCB.

The TJA1028TK is designed for LIN 2.0, LIN 2.1, SAE J2602, and ISO 17987-4:2016 (12 V) applications. Its integrated 5.0 V regulator can power a local microcontroller, communication interface, or sensor circuitry without requiring a separate regulator in compact nodes. The device is intended for automotive and industrial LIN systems where a local 12 V bus must be converted into a regulated 5 V rail and a standardized LIN physical-layer signal.

Typical uses include compact LIN sensor nodes, automotive body-control modules, LIN-to-CAN gateways, actuator interfaces, and industrial diagnostic or control nodes. The 3 x 3 mm HVSON package supports dense PCB layouts, but correct exposed-pad soldering and copper thermal design remain important. The regulator output and transceiver supply pins should be decoupled according to the application guidance in the NXP datasheet.

Designers should confirm that the selected 5.0 V output variant matches the load voltage, that the total regulator demand remains below 70 mA, and that the communication speed suits the selected /20 device. LIN bus layout also requires controlled termination, adequate grounding, protection routing, and separation from high-current or high-voltage switching nodes. This page combines NXP product information, interface characteristics, package details, and practical implementation guidance for faster engineering evaluation.

এর জন্য ড্রপ-ইন বিকল্প TJA1028TK/5V0/20:1 — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।

TJA1028TK/5V0/20/J

✅ ড্রপ-ইন
NXP Semiconductors
📦 8-HVSON (3 x 3 mm)
Single-channel LIN transceiver with integrated voltage regulator · LIN 2.0 and LIN 2.1 · SAE J2602 and ISO 17987-4:2016 for 12 V networks · 5.0 V · Up to 70 mA · Low-dropout voltage regulator · 8-pin HVSON, 3 x 3 mm · Surface mount

মূল্যের জন্য যোগাযোগ করুন

ডেটাশিট দেখুন →

TJA1028TK/5V0/20/X

✅ ড্রপ-ইন
📦 8-HVSON (3 x 3 mm)
5.0 V, 20 kbit/s, and 70 mA regulator ratings are unchanged; only the NXP order suffix differs.

📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)

TJA1028TK/5V0/20AZ

✅ ড্রপ-ইন
📦 8-HVSON (3 x 3 mm)
5.0 V, 20 kbit/s, and 70 mA regulator ratings are unchanged; the AZ order designation differs from the target suffix.

📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)

TJA1028TK/5V0/20:1 বিশেষণ

Product Type LIN bus transceiver with integrated low-drop voltage regulator
LIN Compatibility LIN 2.0, LIN 2.1, SAE J2602
ISO Standard ISO 17987-4:2016 (12 V)
Bus Communication Mode Half-duplex LIN bus
Nominal LIN Data Rate 20 kbit/s
Integrated Regulator Output 5.0 V
Regulator Output Range 4.9 V to 5.1 V
Maximum Regulator Output Current 70 mA
সাপ্লাই কারেন্ট 4.5 mA
কুইসেন্ট কারেন্ট 45 uA
Regulator Dropout Voltage 200 mV
অপারেটিং তাপমাত্রার পরিসর -40 degrees C to +150 degrees C
Electrostatic Discharge Tolerance Plus or minus 8 kV
প্যাকেজ 8-HVSON (3 x 3 mm) with exposed pad
মাউন্টিং টাইপ Surface mount
RoHS স্ট্যাটাস Compliant
Maximum Supply Voltage 5.1 V
Minimum Supply Voltage 4.9 V

TJA1028TK/5V0/20:1 8-hvson (3 x 3 mm) with exposed pad পিন কনফিগারেশন গাইড

TJA1028TK/5V0/20:1 (8-hvson (3 x 3 mm) with exposed pad প্যাকেজ)-এর পিন কনফিগারেশন। পিন নম্বরিং, ফাংশন এবং সংযোগ ডায়াগ্রাম প্রস্তুতকারকের ডেটাশিটে সংজ্ঞায়িত করা আছে। সঠিক ফুটপ্রিন্ট এবং সোল্ডারিং নির্দেশিকার জন্য এটি দেখুন।

TJA1028TK/5V0/20:1-এর জন্য 8-hvson (3 x 3 mm) with exposed pad প্যাকেজ পিনআউট ডায়াগ্রাম

এর জন্য বিস্তারিত পিনআউট ডেটা পাওয়া যায়নি TJA1028TK/5V0/20:1.

দেখুন ডেটাশিট সম্পূর্ণ পিন কনফিগারেশনের জন্য।

সাধারণ ব্যবহার

TJA1028TK/5V0/20:1 এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Automotive LIN Sensor Node, Automotive Body Control Module, LIN-to-CAN Gateway, Actuator and Motor Interface Node, Industrial LIN Control Module, Compact Diagnostics and Test Node.

🚗

Automotive LIN Sensor Node

The TJA1028TK/5V0/20:1 fits a compact automotive LIN sensor node that needs both bus communication and a local regulated supply. Its 20 kbit/s LIN interface supports LIN 2.0, LIN 2.1, SAE J2602, and ISO 17987-4:2016, while the integrated regulator provides 4.9 V to 5.1 V at up to 70 mA. A microcontroller, sensor interface, and conditioning circuit can therefore share a 5 V rail without a separate regulator. The 3 x 3 mm 8-HVSON package limits board area, but designers must preserve the exposed-pad thermal path and observe the datasheet decoupling requirements.

🚗

Automotive Body Control Module

In a body-control module, the TJA1028TK/5V0/20:1 can connect a low-speed LIN sub-network to a higher-level controller while powering nearby 5 V circuitry. The 70 mA regulator capability accommodates qualified local loads when the complete module budget remains below that limit. Its -40 degrees C to +150 degrees C operating range supports harsh vehicle environments, and the listed plus or minus 8 kV ESD tolerance assists interface robustness. Layout should keep the LIN route away from motor, relay, and inductive switching paths, while grounding and protection must follow the application guidance in the NXP documentation.

🌐

LIN-to-CAN Gateway

The TJA1028TK/5V0/20:1 is useful in a LIN-to-CAN gateway where a gateway processor must monitor or control slower LIN nodes while supplying a local 5 V rail. The 20 kbit/s interface is appropriate for LIN sub-networks that do not require the faster communication classes. Its integrated regulator can simplify the power tree by supplying up to 70 mA, but the gateway may need a more capable regulator if its processor, communications hardware, and indicators exceed that budget. Keep the LIN transceiver supply and ground paths clean to prevent data errors in the gateway.

🔧

Actuator and Motor Interface Node

The TJA1028TK/5V0/20:1 can serve as the communication and local-power element in a LIN actuator node. The transceiver provides the standardized LIN physical interface, while the 5.0 V regulator can power a controller, position sensor, or logic stage drawing no more than 70 mA. Because actuator boards often contain switching devices and inductive loads, the LIN route and regulator reference should remain isolated from high-current edges. The exposed pad under the 8-HVSON package must be connected to the recommended ground and thermal-copper arrangement for reliable heat dissipation.

🏭

Industrial LIN Control Module

An industrial LIN control module can use the TJA1028TK/5V0/20:1 when the bus operates at 20 kbit/s and the module includes a 12 V input with a compact 5 V load. The integrated regulator supplies 4.9 V to 5.1 V up to 70 mA, simplifying the power section of a distributed control node. Its wide -40 degrees C to +150 degrees C range supports demanding equipment environments, although the complete product still requires system-level thermal validation. Correct termination, robust grounding, and controlled cable routing are essential for dependable communication across industrial harnesses.

🖥️

Compact Diagnostics and Test Node

The TJA1028TK/5V0/20:1 can be incorporated into a compact diagnostics node that interrogates LIN-connected devices and reports their status to a host controller. The 20 kbit/s bus rate is suitable for low-speed diagnostic and service functions, and the integrated 5.0 V regulator removes one supply block from a space-constrained board. Its 3 x 3 mm HVSON footprint supports dense test hardware, while the exposed pad provides a thermal path for continuous operation. The design must maintain clean separation between diagnostic communication and high-energy test loads to avoid bus errors or device damage.

What is the TJA1028TK/5V0/20:1?
The TJA1028TK/5V0/20:1 is a NXP Semiconductors half-duplex LIN transceiver with an integrated 5.0 V low-dropout voltage regulator. According to the NXP product page, it supports LIN 2.0, LIN 2.1, SAE J2602, and ISO 17987-4:2016 (12 V), supplies up to 70 mA through the regulator, and is intended for compact automotive and industrial LIN nodes.
What is the output voltage of TJA1028TK/5V0/20:1?
The TJA1028TK/5V0/20:1 uses its integrated regulator to produce a nominal 5.0 V output with a stated range of 4.9 V to 5.1 V. According to NXP product information, the low-drop regulator can deliver up to 70 mA, making the device suitable for powering a local controller, sensor interface, or other low-power circuitry connected to a LIN node.
What LIN standards does TJA1028TK/5V0/20:1 support?
The TJA1028TK/5V0/20:1 supports LIN 2.0, LIN 2.1, SAE J2602, and ISO 17987-4:2016 for 12 V systems. These standards define the protocol behavior, electrical characteristics, and interoperability requirements for LIN nodes. The manufacturer product page confirms that the TJA1028 family was developed for compact local interconnect network nodes.
What data rate does TJA1028TK/5V0/20:1 support?
The TJA1028TK/5V0/20:1 is the 20 kbit/s member of the TJA1028 family, indicated by the /20 portion of its order code. The half-duplex LIN interface communicates over a single bus conductor and uses the integrated 5.0 V regulator to support local node electronics. Confirm that the controller and attached slave nodes use a compatible communication rate.
Where can I download the TJA1028TK/5V0/20:1 datasheet?
The official TJA1028TK product page at NXP provides the manufacturer datasheet and product information for this device family. The datasheet contains the pin descriptions, application diagram, electrical characteristics, LIN interface behavior, regulator limits, and application guidance. Use the TJA1028TK/5V0/20:1 ordering information to confirm that the 5.0 V, 20 kbit/s configuration matches the intended design.
Where can I find the TJA1028TK/5V0/20:1 pinout?
The TJA1028TK/5V0/20:1 pinout is shown in the NXP manufacturer datasheet and product documentation. The device uses an 8-HVSON package with a 3 x 3 mm footprint and an exposed thermal pad. Use the pin-description table and land pattern in the datasheet when assigning tracks and connecting the LIN bus, regulator output, ground, and supply pins.
How much current can the TJA1028TK/5V0/20:1 regulator provide?
The integrated regulator in the TJA1028TK/5V0/20:1 can deliver up to 70 mA at a nominal 5.0 V output. NXP lists a regulator output range of 4.9 V to 5.1 V, a 200 mV dropout voltage, 4.5 mA supply current, and a 45 uA quiescent-current figure. The complete node load must remain within the regulator and thermal limits stated in the datasheet.
Is TJA1028TK/5V0/20:1 suitable for automotive applications?
The TJA1028TK/5V0/20:1 is suitable for demanding 12 V automotive LIN applications because it supports LIN 2.0, LIN 2.1, SAE J2602, and ISO 17987-4:2016. Its operating temperature range is -40 degrees C to +150 degrees C, and the listed ESD tolerance is plus or minus 8 kV. Final qualification should follow the system-level requirements for the vehicle platform.
What can replace the TJA1028TK/5V0/20:1?
A true drop-in replacement must match the 8-HVSON (3 x 3 mm) footprint, pin arrangement, 5.0 V regulator configuration, and 20 kbit/s LIN rating. NXP lists orderable TJA1028TK/5V0/20,1, TJA1028TK/5V0/20/J, TJA1028TK/5V0/20/X, and TJA1028TK/5V0/20AZ configurations in the same family. Confirm the exact suffix, temperature grade, packing, and datasheet limits before substitution.
Is TJA1028TK/5V0/20:1 the same as TJA1028TK/5V0/20/J?
The TJA1028TK/5V0/20:1 and TJA1028TK/5V0/20/J identify configurations within the same NXP TJA1028TK family, but their suffix codes must be checked for packing and order-code differences. NXP community information states that the /J tape-and-reel packing is identical to the /20,1 configuration. Verify the manufacturer ordering table before treating the two markings as equivalent.
When should I choose TJA1028TK/5V0/20:1 over another LIN transceiver?
Choose the TJA1028TK/5V0/20:1 when a compact LIN node needs both a 20 kbit/s bus transceiver and an integrated 5.0 V regulator capable of supplying up to 70 mA. This integration can simplify compact sensor or actuator modules. A separate-regulator transceiver may be preferable when the local supply requirement, bus speed, package, or protection needs differ from the TJA1028 specification.
Is TJA1028TK/5V0/20:1 suitable for an industrial LIN sensor node?
The TJA1028TK/5V0/20:1 can suit a 12 V industrial LIN sensor node when its 20 kbit/s communication rate and 5.0 V, 70 mA regulator capability meet the load requirements. Its -40 degrees C to +150 degrees C operating range provides substantial environmental headroom. The final design must still validate bus timing, grounding, protection, and enclosure-related temperature behavior.
What is the difference between TJA1028TK/5V0/20:1 and TJA1028DT?
NXP community information describes the TJA1028DT as functionally identical to TJA1028T/5V0/20 and says it uses a slightly modified die and package bill of materials. The TJA1028TK/5V0/20:1 is identified as an 8-HVSON (3 x 3 mm) device, so the package and exposed-pad land pattern must be compared directly before considering TJA1028DT a physical drop-in replacement.
What are the key specifications of TJA1028TK/5V0/20:1 that engineers should know?
The key TJA1028TK/5V0/20:1 specifications are a 5.0 V nominal regulated output from 4.9 V to 5.1 V, up to 70 mA regulator current, a 20 kbit/s LIN version, and operation from -40 degrees C to +150 degrees C. The half-duplex transceiver supports LIN 2.0, LIN 2.1, SAE J2602, and ISO 17987-4:2016, while the package is 8-HVSON (3 x 3 mm) with an exposed pad.
Where can I buy TJA1028TK/5V0/20:1 and what is the price?
The TJA1028TK/5V0/20:1 can be requested through the Request a Quote form on this page, where current pricing, stock status, lead time, and order quantities can be confirmed. The product is an NXP 8-HVSON LIN transceiver with an integrated 5.0 V regulator rated to 70 mA. Use the exact /5V0/20:1 ordering code when requesting a quotation.
What is the lead time and stock status for TJA1028TK/5V0/20:1?
Current stock and lead time for the TJA1028TK/5V0/20:1 should be confirmed through the Request a Quote form on this page. The exact order code denotes the 5.0 V regulator and 20 kbit/s LIN configuration in the NXP TJA1028TK family. Requesting the exact suffix helps avoid mismatches between electrically similar orderable configurations.

এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা TJA1028TK/5V0/20:1 — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।

নির্বাচন গাইড

Choose the TJA1028TK/5V0/20:1 for a compact 12 V LIN node that needs a 20 kbit/s half-duplex interface and a local 5.0 V supply of up to 70 mA. The integrated regulator can reduce board area and simplify the power tree in sensor nodes, actuator modules, body-control units, gateways, and industrial control nodes. Select an alternate TJA1028TK order code only after checking its exact suffix, packing, temperature qualification, and procurement status against the manufacturer ordering information. Do not treat a different package or an unverified cross-brand device as a drop-in replacement. If the load exceeds 70 mA, the required bus rate is not 20 kbit/s, or the system needs more than 70 mA of regulated local power, select a LIN transceiver with a separate regulator or a higher-current regulator architecture.

বিকল্পের সাথে তুলনা

পারামিটার এই পণ্য TJA1028TK/5V0/20/J TJA1028TK/5V0/20/X TJA1028TK/5V0/20AZ
Brand NXP Semiconductors NXP Semiconductors NXP Semiconductors NXP Semiconductors
Package 8-HVSON (3 x 3 mm) with exposed pad 8-HVSON (3 x 3 mm) with exposed pad 8-HVSON (3 x 3 mm) with exposed pad 8-HVSON (3 x 3 mm) with exposed pad
Device Type LIN transceiver with integrated low-drop voltage regulator LIN transceiver with integrated low-drop voltage regulator LIN transceiver with integrated low-drop voltage regulator LIN transceiver with integrated low-drop voltage regulator
Integrated Regulator Output 5.0 V nominal; 4.9 V to 5.1 V 5.0 V nominal; 4.9 V to 5.1 V 5.0 V nominal; 4.9 V to 5.1 V 5.0 V nominal; 4.9 V to 5.1 V
Regulator Output Current 70 mA maximum 70 mA maximum 70 mA maximum 70 mA maximum
LIN Data Rate 20 kbit/s 20 kbit/s 20 kbit/s 20 kbit/s
Supply Current 4.5 mA 4.5 mA 4.5 mA 4.5 mA
Quiescent Current 45 uA 45 uA 45 uA 45 uA
Operating Temperature Range -40 degrees C to +150 degrees C -40 degrees C to +150 degrees C -40 degrees C to +150 degrees C -40 degrees C to +150 degrees C
Standards Support LIN 2.0, LIN 2.1, SAE J2602, ISO 17987-4:2016 LIN 2.0, LIN 2.1, SAE J2602, ISO 17987-4:2016 LIN 2.0, LIN 2.1, SAE J2602, ISO 17987-4:2016 LIN 2.0, LIN 2.1, SAE J2602, ISO 17987-4:2016

মূল পার্থক্যসমূহ

  • Combines the LIN transceiver and local 5 V regulator in one 8-HVSON device (বনামTJA1028TK/5V0/20/J)
  • Supports the 20 kbit/s LIN class with standardized automotive and industrial compliance (বনামTJA1028TK/5V0/20/X)
  • Provides a wide automotive temperature range (বনামTJA1028TK/5V0/20AZ)

ডিজাইন নোট

Place the input and regulator-output capacitors close to their associated device pins, following the values and layout shown in the NXP application information. Keep the exposed pad connected to the recommended ground structure and use thermal vias only where they do not compromise the land pattern. A compact 3 x 3 mm footprint reduces board area, but it also makes pad soldering and ground-plane continuity especially important for manufacturing reliability.

Route the LIN bus away from motor windings, relay coils, switching power converters, and other high-dv/dt or high-di/dt circuits. Provide a direct return path beneath the transceiver ground reference where the layout permits, and keep the LIN trace short before the connector or harness interface. Check the complete external protection network against the listed plus or minus 8 kV ESD requirement and the system-level surge environment.

Confirm the exact /5V0/20:1 order code before releasing a PCB or placing an order because related TJA1028TK suffixes identify different packing or order configurations. Also verify that the total 5 V load is no greater than 70 mA, that the 20 kbit/s bus rate matches every node, and that the regulator has adequate dropout margin at the minimum bus voltage. Do not substitute a package based only on nominal pin count.

কমপ্লায়েন্স তথ্য

RoHS
Compliant
REACH
Unknown
AEC-Q100
Unknown
লিড ফ্রি
Unknown
হ্যালোজেন ফ্রি
Unknown
কনফ্লিক্ট মিনারেলস
Unknown

RoHS compliance is stated for the TJA1028TK/5V0/20/1 family configuration. The device supports ISO 17987-4:2016 (12 V), SAE J2602, LIN 2.0, and LIN 2.1. No separate AEC-Q100, REACH, halogen-free, or conflict-minerals statement was identified.

ডেটা যাচাই করা হয়েছে: 2026-11-18 — ডেটা XAIPART-এর কম্পোনেন্ট ইঞ্জিনিয়ারিং টিম দ্বারা যাচাই ও কিউরেট করা হয়েছে

সম্পর্কিত অনুসন্ধান

TJA1028TK/5V0/20:1 datasheet TJA1028TK/5V0/20:1 pinout TJA1028TK/5V0/20:1 datasheet pdf TJA1028TK/5V0/20:1 equivalent TJA1028TK/5V0/20:1 replacement TJA1028TK/5V0/20:1 cross reference TJA1028TK/5V0/20:1 price TJA1028TK/5V0/20:1 stock NXP TJA1028TK/5V0/20:1 TJA1028TK/5V0/20:1 8-HVSON TJA1028TK/5V0/20:1 application circuit TJA1028TK/5V0/20:1 vs TJA1028TK/5V0/20/J

সম্পর্কিত কম্পোনেন্ট ও শর্তাবলী

NXP Semiconductors TJA1028TK/5V0/20:1 TJA1028TK/5V0/20/J TJA1028TK/5V0/20/X TJA1028TK/5V0/20AZ LIN transceiver LIN bus Local Interconnect Network automotive interface IC integrated voltage regulator low-dropout regulator half-duplex transceiver 8-HVSON QFN family surface mount LIN 2.0 LIN 2.1 SAE J2602 ISO 17987-4:2016 RoHS 20 kbit/s 5.0 V regulator 70 mA electrostatic discharge
তাৎক্ষণিক বিলওয়াছে রেকোজিউইট
সম্পূর্ণ বিবরণ পূরণ করুন — আমাদের সেলস টিম 24 ঘণ্টার মধ্যে উত্তর দেবে
পার্ট নম্বর উৎপাদক প্যাকেজ QTY লক্ষ্যমূল্য প্রসারিত
✓
বিল প্রস্তুত করা হয়েছে!

আমরা ২৪ ঘণ্টার মধ্যে আপনার ইমেইলে প্রত্যুত্তর দেব

1
RFQ জমা হয়েছে
2
কোটেশন পাওয়া গেছে
3
অর্ডার দেওয়া হয়েছে
4
পেমেন্ট
5
শিপ করা হয়েছে
6
ডেলিভারি হয়েছে
RFQ বিবরণ দেখুন