TJA1028TK/5V0/20:1 - LIN Transceiver with 5V Regulator | NXP
부품 번호: TJA1028TK/5V0/20:1 ✓ 활성TJA1028TK/5V0/20:1 개요
A LIN, or Local Interconnect Network, transceiver is an interface IC that converts logic-level signals between a host controller and a low-cost, single-wire automotive communication bus. LIN belongs to the broader vehicle network-interface hierarchy, where transceivers add the electrical protection and signal conditioning required to communicate reliably over a physically long, noisy harness. The TJA1028 combines this bus-interface role with a local power-supply function, reducing the component count needed by compact LIN nodes.
The device provides a 5.0 V regulator variant with a stated output range of 4.9 V to 5.1 V. The regulator can deliver up to 70 mA, while the listed supply current is 4.5 mA. The /20 version is associated with a 20 kbit/s LIN communication class. NXP also lists operation from -40 degrees C to +150 degrees C, making the device suitable for demanding automotive environments. The package is identified as 8-HVSON (3 x 3 mm), and the exposed pad supports heat dissipation into the PCB.
The TJA1028TK is designed for LIN 2.0, LIN 2.1, SAE J2602, and ISO 17987-4:2016 (12 V) applications. Its integrated 5.0 V regulator can power a local microcontroller, communication interface, or sensor circuitry without requiring a separate regulator in compact nodes. The device is intended for automotive and industrial LIN systems where a local 12 V bus must be converted into a regulated 5 V rail and a standardized LIN physical-layer signal.
Typical uses include compact LIN sensor nodes, automotive body-control modules, LIN-to-CAN gateways, actuator interfaces, and industrial diagnostic or control nodes. The 3 x 3 mm HVSON package supports dense PCB layouts, but correct exposed-pad soldering and copper thermal design remain important. The regulator output and transceiver supply pins should be decoupled according to the application guidance in the NXP datasheet.
Designers should confirm that the selected 5.0 V output variant matches the load voltage, that the total regulator demand remains below 70 mA, and that the communication speed suits the selected /20 device. LIN bus layout also requires controlled termination, adequate grounding, protection routing, and separation from high-current or high-voltage switching nodes. This page combines NXP product information, interface characteristics, package details, and practical implementation guidance for faster engineering evaluation.
드롭인 대체품: TJA1028TK/5V0/20:1 — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
TJA1028TK/5V0/20/J
✅ 드롭인가격 문의
데이터시트 보기 →TJA1028TK/5V0/20/X
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
TJA1028TK/5V0/20AZ
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
TJA1028TK/5V0/20:1 사양
| Product Type | LIN bus transceiver with integrated low-drop voltage regulator |
| LIN Compatibility | LIN 2.0, LIN 2.1, SAE J2602 |
| ISO Standard | ISO 17987-4:2016 (12 V) |
| Bus Communication Mode | Half-duplex LIN bus |
| Nominal LIN Data Rate | 20 kbit/s |
| Integrated Regulator Output | 5.0 V |
| Regulator Output Range | 4.9 V to 5.1 V |
| Maximum Regulator Output Current | 70 mA |
| 공급 전류 | 4.5 mA |
| 대기 전류 | 45 uA |
| Regulator Dropout Voltage | 200 mV |
| 동작 온도 범위 | -40 degrees C to +150 degrees C |
| Electrostatic Discharge Tolerance | Plus or minus 8 kV |
| 패키지 | 8-HVSON (3 x 3 mm) with exposed pad |
| 실장 유형 | Surface mount |
| RoHS 상태 | Compliant |
| Maximum Supply Voltage | 5.1 V |
| Minimum Supply Voltage | 4.9 V |
TJA1028TK/5V0/20:1 8-hvson (3 x 3 mm) with exposed pad 핀 구성 가이드
TJA1028TK/5V0/20:1(8-hvson (3 x 3 mm) with exposed pad 패키지)의 핀 구성입니다. 핀 번호, 기능, 연결 다이어그램은 제조사 데이터시트에 정의되어 있습니다. 정확한 풋프린트와 솔더링 지침은 해당 문서를 참조하십시오.
다음에 대한 상세 핀아웃 데이터 없음: TJA1028TK/5V0/20:1.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
TJA1028TK/5V0/20:1 적합 용도: 6 애플리케이션s: Automotive LIN Sensor Node, Automotive Body Control Module, LIN-to-CAN Gateway, Actuator and Motor Interface Node, Industrial LIN Control Module, Compact Diagnostics and Test Node.
Automotive LIN Sensor Node
The TJA1028TK/5V0/20:1 fits a compact automotive LIN sensor node that needs both bus communication and a local regulated supply. Its 20 kbit/s LIN interface supports LIN 2.0, LIN 2.1, SAE J2602, and ISO 17987-4:2016, while the integrated regulator provides 4.9 V to 5.1 V at up to 70 mA. A microcontroller, sensor interface, and conditioning circuit can therefore share a 5 V rail without a separate regulator. The 3 x 3 mm 8-HVSON package limits board area, but designers must preserve the exposed-pad thermal path and observe the datasheet decoupling requirements.
Automotive Body Control Module
In a body-control module, the TJA1028TK/5V0/20:1 can connect a low-speed LIN sub-network to a higher-level controller while powering nearby 5 V circuitry. The 70 mA regulator capability accommodates qualified local loads when the complete module budget remains below that limit. Its -40 degrees C to +150 degrees C operating range supports harsh vehicle environments, and the listed plus or minus 8 kV ESD tolerance assists interface robustness. Layout should keep the LIN route away from motor, relay, and inductive switching paths, while grounding and protection must follow the application guidance in the NXP documentation.
LIN-to-CAN Gateway
The TJA1028TK/5V0/20:1 is useful in a LIN-to-CAN gateway where a gateway processor must monitor or control slower LIN nodes while supplying a local 5 V rail. The 20 kbit/s interface is appropriate for LIN sub-networks that do not require the faster communication classes. Its integrated regulator can simplify the power tree by supplying up to 70 mA, but the gateway may need a more capable regulator if its processor, communications hardware, and indicators exceed that budget. Keep the LIN transceiver supply and ground paths clean to prevent data errors in the gateway.
Actuator and Motor Interface Node
The TJA1028TK/5V0/20:1 can serve as the communication and local-power element in a LIN actuator node. The transceiver provides the standardized LIN physical interface, while the 5.0 V regulator can power a controller, position sensor, or logic stage drawing no more than 70 mA. Because actuator boards often contain switching devices and inductive loads, the LIN route and regulator reference should remain isolated from high-current edges. The exposed pad under the 8-HVSON package must be connected to the recommended ground and thermal-copper arrangement for reliable heat dissipation.
Industrial LIN Control Module
An industrial LIN control module can use the TJA1028TK/5V0/20:1 when the bus operates at 20 kbit/s and the module includes a 12 V input with a compact 5 V load. The integrated regulator supplies 4.9 V to 5.1 V up to 70 mA, simplifying the power section of a distributed control node. Its wide -40 degrees C to +150 degrees C range supports demanding equipment environments, although the complete product still requires system-level thermal validation. Correct termination, robust grounding, and controlled cable routing are essential for dependable communication across industrial harnesses.
Compact Diagnostics and Test Node
The TJA1028TK/5V0/20:1 can be incorporated into a compact diagnostics node that interrogates LIN-connected devices and reports their status to a host controller. The 20 kbit/s bus rate is suitable for low-speed diagnostic and service functions, and the integrated 5.0 V regulator removes one supply block from a space-constrained board. Its 3 x 3 mm HVSON footprint supports dense test hardware, while the exposed pad provides a thermal path for continuous operation. The design must maintain clean separation between diagnostic communication and high-energy test loads to avoid bus errors or device damage.
엔지니어링 참조 데이터: TJA1028TK/5V0/20:1 — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | TJA1028TK/5V0/20/J | TJA1028TK/5V0/20/X | TJA1028TK/5V0/20AZ |
|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 8-HVSON (3 x 3 mm) with exposed pad | 8-HVSON (3 x 3 mm) with exposed pad | 8-HVSON (3 x 3 mm) with exposed pad | 8-HVSON (3 x 3 mm) with exposed pad |
| Device Type | LIN transceiver with integrated low-drop voltage regulator | LIN transceiver with integrated low-drop voltage regulator | LIN transceiver with integrated low-drop voltage regulator | LIN transceiver with integrated low-drop voltage regulator |
| Integrated Regulator Output | 5.0 V nominal; 4.9 V to 5.1 V | 5.0 V nominal; 4.9 V to 5.1 V | 5.0 V nominal; 4.9 V to 5.1 V | 5.0 V nominal; 4.9 V to 5.1 V |
| Regulator Output Current | 70 mA maximum | 70 mA maximum | 70 mA maximum | 70 mA maximum |
| LIN Data Rate | 20 kbit/s | 20 kbit/s | 20 kbit/s | 20 kbit/s |
| Supply Current | 4.5 mA | 4.5 mA | 4.5 mA | 4.5 mA |
| Quiescent Current | 45 uA | 45 uA | 45 uA | 45 uA |
| Operating Temperature Range | -40 degrees C to +150 degrees C | -40 degrees C to +150 degrees C | -40 degrees C to +150 degrees C | -40 degrees C to +150 degrees C |
| Standards Support | LIN 2.0, LIN 2.1, SAE J2602, ISO 17987-4:2016 | LIN 2.0, LIN 2.1, SAE J2602, ISO 17987-4:2016 | LIN 2.0, LIN 2.1, SAE J2602, ISO 17987-4:2016 | LIN 2.0, LIN 2.1, SAE J2602, ISO 17987-4:2016 |
주요 차별점
- Combines the LIN transceiver and local 5 V regulator in one 8-HVSON device (vs TJA1028TK/5V0/20/J)
- Supports the 20 kbit/s LIN class with standardized automotive and industrial compliance (vs TJA1028TK/5V0/20/X)
- Provides a wide automotive temperature range (vs TJA1028TK/5V0/20AZ)
설계 노트
Place the input and regulator-output capacitors close to their associated device pins, following the values and layout shown in the NXP application information. Keep the exposed pad connected to the recommended ground structure and use thermal vias only where they do not compromise the land pattern. A compact 3 x 3 mm footprint reduces board area, but it also makes pad soldering and ground-plane continuity especially important for manufacturing reliability.
Route the LIN bus away from motor windings, relay coils, switching power converters, and other high-dv/dt or high-di/dt circuits. Provide a direct return path beneath the transceiver ground reference where the layout permits, and keep the LIN trace short before the connector or harness interface. Check the complete external protection network against the listed plus or minus 8 kV ESD requirement and the system-level surge environment.
Confirm the exact /5V0/20:1 order code before releasing a PCB or placing an order because related TJA1028TK suffixes identify different packing or order configurations. Also verify that the total 5 V load is no greater than 70 mA, that the 20 kbit/s bus rate matches every node, and that the regulator has adequate dropout margin at the minimum bus voltage. Do not substitute a package based only on nominal pin count.
규정 준수 정보
RoHS compliance is stated for the TJA1028TK/5V0/20/1 family configuration. The device supports ISO 17987-4:2016 (12 V), SAE J2602, LIN 2.0, and LIN 2.1. No separate AEC-Q100, REACH, halogen-free, or conflict-minerals statement was identified.