Infineon

TLE8250GVIOXUMA5 - High-Speed CAN Transceiver 1MBd | Infineon

MPN: TLE8250GVIOXUMA5 ✓ সক্রিয়
4.5 V to 5.5 V Vdss PG-DSO-8-16 Package
সর্বনিম্ন অর্ডার পরিমাণ: 1 |

TLE8250GVIOXUMA5 সারাংশ

The Infineon Technologies TLE8250GVIOXUMA5 is a high-speed CAN bus transceiver with a separate I/O voltage input (VIO), delivering 1 MBd data rate in a half-duplex 1-driver/1-receiver configuration housed in an 8-pin PG-DSO-8 (SOIC-8) package. It operates from a 4.5V to 5.5V supply over a -40C to +150C temperature range and features 200 mV receiver hysteresis.

A CAN (Controller Area Network) transceiver is the physical-layer interface between a CAN protocol controller (usually integrated in a microcontroller) and the twisted-pair bus wires. Within the automotive and industrial networking hierarchy, it sits at the bottom of the stack: CAN network -> high-speed CAN physical layer (ISO 11898-2) -> CAN transceiver -> CAN controller. The transceiver converts the controller's TXD logic stream into differential bus signaling on CANH and CANL, and recovers the differential bus signal to a logic-level RXD output, while protecting the microcontroller against disturbances coming from the network.

Key features include full ISO 11898-2 compliance, up to 1 MBd signaling for classical CAN frames, low electromagnetic emission (EME) and high immunity against external electromagnetic interference (EMI), and robust ESD protection on the bus pins. The separate VIO pin lets the TXD and RXD logic levels adapt to 3.3V or 5V microcontroller ports, eliminating level-shifting glue logic in mixed-voltage systems.

The device integrates a highly symmetric driver stage that minimizes bus-line unbalance, improving common-mode noise behavior. Receiver hysteresis of 200 mV suppresses false switching from bus reflections and noise, and integrated protection functions guard against transient events typical of automotive 12V environments.

Typical applications include automotive body and powertrain ECUs, industrial CANopen and DeviceNet nodes, gateways connecting CAN to other networks, and motor-drive communication modules where a 3.3V MCU must talk over a 5V CAN physical layer.

Design tip: keep the VIO pin within its specified range and decouple VCC and VIO separately; the transceiver is half-duplex, so ensure the protocol controller performs proper arbitration and never drives TXD against an active reception.

This page synthesizes drop-in alternatives, cross-reference data, applications, and engineering design notes in one place, beyond what a standard distributor listing provides.

এর জন্য ড্রপ-ইন বিকল্প TLE8250GVIOXUMA5 — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।

এই সিরিজের ভ্যারিয়েন্ট

একই সিরিজের মডেল যেগুলো drop-in compatible TLE8250GVIOXUMA5 (একই form factor এবং footprint) — পার্থক্য রয়েছে Package, RoHS Status, Data Rate, Product Type, Automotive Qualification.

NXP Semiconductors
Package: 8-pin SOIC
RoHS Status: unknown
Product Type: High-speed CAN transceiver
NXP Semiconductors
Package: 8-SO (SOIC-8, 3.9 mm body)
RoHS Status: Compliant
Data Rate: Up to 1 Mbit/s
এর সাথে তুলনা করুন TLE8250GVIOXUMA5 →
Infineon
Package: PG-DSO-8
RoHS Status: RoHS compliant green product
Product Type: CAN bus transceiver
এর সাথে তুলনা করুন TLE8250GVIOXUMA5 →
Infineon
Package: PG-DSO-8-16
RoHS Status: Compliant
Product Type: CAN bus transceiver
এর সাথে তুলনা করুন TLE8250GVIOXUMA5 →
Infineon
Package: PG-DSO-8-16, 8-SOIC, 3.90 mm width
Data Rate: 1 Mbaud
Product Type: High-speed CAN transceiver
এর সাথে তুলনা করুন TLE8250GVIOXUMA5 →

TLE8250GXUMA5

✅ ড্রপ-ইন
Infineon
📦 PG-DSO-8-16 (8-SOIC)
High-speed CAN transceiver · CANbus · ISO 11898-2 · 1 Mbaud · 1 · 1 · Half duplex · 4.5 V to 5.5 V

মূল্যের জন্য যোগাযোগ করুন

ডেটাশিট দেখুন →

TJA1051T/1J

✅ ড্রপ-ইন
NXP Semiconductors
📦 8-SOIC (3.90mm width)
High-speed CAN transceiver · 5 Mbit/s · 5 V · Two-wire differential CAN bus · Differential transmit and differential receive · Normal and SILENT mode · CAN protocol controller with TX and RX signals · 8-pin SOIC

মূল্যের জন্য যোগাযোগ করুন

ডেটাশিট দেখুন →

TJA1057GTJ

✅ ড্রপ-ইন
NXP Semiconductors
📦 8-SOIC (3.90mm width)
High-speed CAN transceiver · Up to 1 Mbit/s · 1/1 · ISO 11898-2 (CAN, CAN FD) · 4.75 V to 5.25 V · -40 °C to +150 °C · 8-SO (SOIC-8, 3.9 mm body) · Surface Mount

মূল্যের জন্য যোগাযোগ করুন

ডেটাশিট দেখুন →

TLE6250GV33XUMA1

✅ ড্রপ-ইন
Infineon
📦 PG-DSO-8
CAN bus transceiver · 1/1 half-duplex transceiver · 1 Mbit/s · 12 V to 24 V · 3.3 V to 5 V · 70 mA · 12 V and 24 V automotive battery systems · Normal mode and standby mode

মূল্যের জন্য যোগাযোগ করুন

ডেটাশিট দেখুন →

TLE8250GVIOXUMA5 বিশেষণ

Protocol CANbus
ডেটা রেট 1 MBd
Number of Drivers/Receivers 1/1
Duplex Half
সাপ্লাই ভোল্টেজ 4.5 V to 5.5 V
Receiver Hysteresis 200 mV
অপারেটিং তাপমাত্রা -40C to +150C
মাউন্টিং টাইপ Surface Mount
Supplier Device Package PG-DSO-8-16
প্যাকেজ / কেস 8-SOIC (0.154in, 3.90mm Width)
Physical Layer Standard ISO 11898-2 (high-speed CAN)
I/O Voltage Input (VIO) Yes, separate logic-level supply
ESD Protection Robust ESD protection on bus pins
EME/EMI Low electromagnetic emission, high EMI immunity
ECCN EAR99
HTSUS 8542.39.0001
Moisture Sensitivity Level 2A
Part Status Active

TLE8250GVIOXUMA5 পিন কনফিগারেশন

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
পিন 1 TXD — Transmit data input from CAN controller (logic level set by VIO)
পিন 2 GND — Ground
পিন 3 VCC — Transceiver supply, 4.5V to 5.5V
পিন 4 RXD — Receive data output to CAN controller (logic level set by VIO)
পিন 5 VIO — I/O voltage input setting TXD/RXD logic levels
পিন 6 CANL — Low-level CAN bus line
পিন 7 CANH — High-level CAN bus line
পিন 8 NC — Not connected (per datasheet)

সাধারণ ব্যবহার

TLE8250GVIOXUMA5 এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Automotive Body Electronics ECUs, Industrial CANopen and DeviceNet Nodes, CAN Gateways and Network Bridges, Motor Drive and Inverter Communication, Agricultural and Off-Highway Vehicles, Diagnostic Interfaces and Test Tools.

🚗

Automotive Body Electronics ECUs

Body control modules, door modules, lighting controllers, and seat ECUs all communicate over 500 kbps high-speed CAN, exactly the regime the TLE8250GVIOXUMA5 targets. Its ISO 11898-2 compliance guarantees interoperability with the rest of the vehicle bus, while low electromagnetic emission helps the module pass automotive EMC test plans without extra suppression components. The VIO pin lets a cost-optimized 3.3V body microcontroller connect directly, removing level-shifter ICs from the BOM. The -40C to +150C operating range covers passenger-compartment and near-engine mounting locations, and the robust ESD protection on CANH/CANL withstands the transient events typical of 12V vehicle harnesses.

🏭

Industrial CANopen and DeviceNet Nodes

Industrial fieldbus nodes - drives, IO blocks, sensors, and gateways - rely on high-speed CAN physical layers standardized by CANopen and DeviceNet. The TLE8250GVIOXUMA5 supplies the 1 MBd-capable differential interface these profiles require, with 200 mV receiver hysteresis that stabilizes reception on long, cable-infested factory networks prone to reflections and common-mode noise. Its low-EMI driver helps panels meet industrial EMC requirements, and the separate VIO input matches both legacy 5V PLC logic and modern 3.3V MCUs on the same PCB layout. High immunity to external electromagnetic interference keeps communication intact near variable-frequency drives and contactor switching events common in industrial cabinets.

🌐

CAN Gateways and Network Bridges

Gateways bridging powertrain CAN, body CAN, and diagnostic lines need transceivers that behave identically on every channel, and the TLE8250GVIOXUMA5 provides that uniform ISO 11898-2 physical layer at up to 1 MBd per channel. The VIO input is particularly useful in gateway designs that pair a 3.3V application MCU with mixed 5V signaling, avoiding level translators that add delay to the critical RXD path. Its low EME is important because gateways often sit near sensitive RF or analog sections, and the robust bus-pin ESD protection handles cable-attached diagnostic interfaces. Per Infineon, the transceiver also shields the microcontroller against disturbances coming from the network.

⚙️

Motor Drive and Inverter Communication

Servo drives, inverters, and motion controllers use CAN for setpoint and status traffic in noisy power-electronic environments. The TLE8250GVIOXUMA5's high immunity against external electromagnetic interference is the deciding parameter here: switching nodes of tens of volts per nanosecond couple large transients into the bus wiring, and the receiver's 200 mV hysteresis plus the transceiver's common-mode rejection keep bit error rates low. The 4.5V to 5.5V VCC rail is typically already present in drive control boards, and the VIO pin accepts the 3.3V outputs of modern DSP/MCU control sections directly. The PG-DSO-8 footprint also supports isolation-compatible layouts where a digital isolator sits between controller and transceiver.

🚜

Agricultural and Off-Highway Vehicles

Tractors, harvesters, construction machines, and marine equipment standardize on CAN (including J1939 at 250 kbps and ISOBUS implementations), all of which run comfortably within the TLE8250GVIOXUMA5's 1 MBd capability. These platforms expose the transceiver to harsher conditions than passenger cars: long harnesses, 24V system transients, moisture, and wide temperature swings. The part's -40C to +150C rating and robust ESD protection on the bus pins address those stressors, while ISO 11898-2 compliance guarantees node interoperability across mixed-vendor fleets. The VIO feature supports the 3.3V display and telematics controllers increasingly integrated into off-highway cabs alongside legacy 5V logic.

🔧

Diagnostic Interfaces and Test Tools

Handheld CAN analyzers, OBD adapters, and production EOL programmers benefit from the TLE8250GVIOXUMA5's combination of full 1 MBd support - needed for fast flash reprogramming over CAN - and the VIO input, which lets one hardware design talk to both 3.3V and 5V targets without modification. Robust bus-pin ESD handling matters because diagnostic cables are plugged into arbitrary vehicles and modules all day, accumulating electrostatic stress. The compact PG-DSO-8 package fits the small probe-form-factor PCBs typical of these tools, and low EME avoids corrupting nearby RF measurements when the tool is used in lab or EMC-chamber settings.

What is the TLE8250GVIOXUMA5 and what does it do?
The TLE8250GVIOXUMA5 is a high-speed CAN bus transceiver from Infineon Technologies. It acts as the physical-layer interface between a CAN protocol controller and the bus, driving differential signals onto CANH/CANL at up to 1 MBd and recovering received signals to a logic-level RXD output. It operates from a 4.5V to 5.5V supply, includes a separate VIO pin for 3.3V or 5V logic-level adaptation, and is specified from -40C to +150C in an 8-pin PG-DSO-8 package. Per Infineon, it is ISO 11898-2 compliant and suited for automotive and industrial CAN networks.
What is the supply voltage range of TLE8250GVIOXUMA5?
The TLE8250GVIOXUMA5 operates from a 4.5V to 5.5V supply voltage on its VCC pin. In addition, it provides a separate VIO pin that sets the logic levels of the TXD input and RXD output, so a 3.3V microcontroller port can directly interface with the 5V-supplied transceiver without external level shifters. The receiver uses 200 mV hysteresis to reject bus noise, and the device is rated for operation from -40C to +150C, covering demanding automotive under-hood environments.
What is the difference between TLE8250GVIOXUMA5 and TLE8250GXUMA5?
The main difference is the VIO pin: the TLE8250GVIOXUMA5 includes a separate I/O voltage input that lets TXD/RXD logic levels follow a 3.3V or 5V microcontroller supply, while the TLE8250GXUMA5 variant is the version without this VIO feature. Both parts share the same PG-DSO-8-16 package, 1 MBd data rate, 4.5V to 5.5V VCC range, half-duplex 1/1 configuration, and -40C to +150C temperature range, per DigiKey listings. Choose the VIO version when your controller IO runs below 5V.
Can TJA1051T/1J replace TLE8250GVIOXUMA5?
The NXP TJA1051T/1J is a close cross-brand candidate: it is a high-speed CAN transceiver, 1 Mbps, normal/silent modes, 5.5V supply, in an 8-pin SOIC package, as listed in distributor comparison data against the TLE8250GVIOXUMA5. Verify pin-to-pin mapping (TXD, GND, VCC, RXD, and bus pins) against both datasheets before qualifying the swap, and note that the TJA1051T/1J does not replicate the TLE8250GVIO XUMA5 VIO logic-level supply exactly, so any 3.3V microcontroller interface must be confirmed compatible.
What is the best drop-in replacement for TLE8250GVIOXUMA5?
The closest same-brand drop-in is the Infineon TLE8250GXUMA5, which shares the identical PG-DSO-8-16 footprint, 1 MBd rate, and supply range but omits the VIO logic-level input. Cross-brand drop-in candidates found in distributor cross-reference data include the NXP TJA1051T/1J and NXP TJA1057GTJ, both high-speed CAN transceivers in 8-pin SOIC packages. Because pinout and standby/behavioral details can differ between vendors, review the pin-description table of each manufacturer datasheet and test bus timing before switching production.
What is the data rate of TLE8250GVIOXUMA5?
The TLE8250GVIOXUMA5 supports a data rate of up to 1 MBd (1 Mbps), which corresponds to the maximum signaling rate of classical high-speed CAN per the ISO 11898-2 physical layer standard. According to the device specification, it is a half-duplex transceiver with one driver and one receiver, and 200 mV of receiver hysteresis for noise immunity. This rate is sufficient for 500 kbps body/powertrain buses and full-rate 1 Mbps powertrain or chassis networks in automotive and industrial systems.
Is TLE8250GVIOXUMA5 suitable for 3.3V microcontrollers?
Yes, the TLE8250GVIOXUMA5 is designed for direct connection to 3.3V microcontroller CAN ports. Its separate VIO pin defines the logic thresholds of the TXD input and RXD output, so the IO levels can follow a 3.3V rail while the transceiver itself runs from a 4.5V to 5.5V supply on VCC. This removes the need for external level-shifting circuitry. Simply tie VIO to the microcontroller IO supply rail and decouple it appropriately; this is the core benefit of the VIO variant over the plain TLE8250G.
What package does TLE8250GVIOXUMA5 come in?
The TLE8250GVIOXUMA5 comes in an 8-pin PG-DSO-8-16 package, which is Infineon's designation for a standard 8-SOIC body of 3.90mm width (0.154in) in surface-mount form. This footprint is widely shared across high-speed CAN transceivers from multiple vendors, which simplifies second-source qualification on existing PCB land patterns. According to distributor specification listings, the device is supplied in tape-and-reel packing for automated assembly, with moisture sensitivity level 2A.
Where can I download the TLE8250GVIOXUMA5 datasheet PDF?
The official datasheet is available through Infineon's TLE8250G product page at infineon.com, which covers the TLE8250GVIO variant family. Distributor pages such as DigiKey and Mouser also link to the current manufacturer datasheet PDF for this part number. For design work, always use the latest revision from the manufacturer page, since it contains the pin-description table, electrical characteristics, timing parameters, and application information needed to qualify the transceiver in an ISO 11898-2 network.
Where can I buy TLE8250GVIOXUMA5 and check stock?
You can request current price, stock, and lead time for the TLE8250GVIOXUMA5 through the Request a Quote form on this page. Multiple authorized distribution channels carry this Infineon part as an active line item, and availability changes daily, so a quote request gives you fresh pricing and confirmed delivery rather than stale listing data. For volume production, include your target quantity and required date on the quote form so scheduling and reel quantities can be confirmed before ordering.
What is the operating temperature range of TLE8250GVIOXUMA5?
The TLE8250GVIOXUMA5 is specified for operation from -40C to +150C ambient temperature. This wide range makes it suitable for automotive applications including under-hood and near-engine ECUs where temperatures far exceed consumer-grade limits, as well as industrial environments with high ambient heat. The PG-DSO-8 package provides adequate thermal capability for the transceiver's dissipation, and the device integrates protection functions appropriate to the harsh 12V automotive electrical environment, per Infineon's product information.
Is TLE8250GVIOXUMA5 the same as a 5V CAN transceiver with 3.3V IO?
Yes, functionally the TLE8250GVIOXUMA5 is exactly that: a 5V-supplied (4.5V to 5.5V VCC) high-speed CAN transceiver whose TXD/RXD logic levels are referenced to a separate VIO supply pin, allowing 3.3V microcontroller connections. It should not be confused with true 3.3V-only CAN transceivers such as the TI TCAN33x family, which run the entire transceiver from a 3.3V rail. The VIO architecture keeps the bus driver at full 5V drive levels, which supports longer stubs and better noise margins on the physical bus.
Does TLE8250GVIOXUMA5 support CAN FD?
No, the TLE8250GVIOXUMA5 is a classical high-speed CAN transceiver rated at up to 1 MBd. CAN FD operation at data-phase rates above 2 Mbps requires a CAN FD-capable transceiver such as Infineon's TLE1551 family or comparable CAN FD parts, which guarantee loop delay and symmetry at faster bit times. If your design currently uses classical CAN at 500 kbps or 1 Mbps, the TLE8250GVIOXUMA5 is fully appropriate; for a future CAN FD migration, plan a transceiver upgrade alongside the controller change.
When should I choose TLE8250GVIOXUMA5 over TJA1057GTJ?
Choose the TLE8250GVIOXUMA5 when your board needs the separate VIO logic-level input to mate a 3.3V microcontroller with a 5V CAN physical layer, and when you want Infineon's documented low-EME/EMI behavior and robust ESD protection for automotive networks. Choose the NXP TJA1057GTJ when second-sourcing policy favors NXP or when its specific standby and wake behavior better matches your power-management concept. Both are high-speed CAN transceivers in 8-pin SOIC packages at similar data rates, so confirm pinout and standby current differences in the datasheets before finalizing.
What are the key specifications of TLE8250GVIOXUMA5 that engineers should know?
Core facts: Infineon TLE8250GVIOXUMA5 is an ISO 11898-2 high-speed CAN transceiver, 1 MBd maximum data rate, half-duplex with 1 driver and 1 receiver, 200 mV receiver hysteresis, VCC from 4.5V to 5.5V, separate VIO pin for logic-level adaptation, operating temperature -40C to +150C, 8-pin PG-DSO-8 (SOIC-8, 3.90mm width) surface-mount package, MSL 2A, ECCN EAR99. It targets automotive and industrial CAN nodes with low EME and robust ESD protection. These parameters define footprint, bus timing, and microcontroller compatibility for new designs.

এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা TLE8250GVIOXUMA5 — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।

নির্বাচন গাইড

Choose the TLE8250GVIOXUMA5 when your CAN node pairs a 3.3V microcontroller with a standard 5V-supplied ISO 11898-2 physical layer, or when you want a single transceiver design to serve both 3.3V and 5V controller variants - the VIO pin removes level-shift logic entirely. Choose the TLE8250GXUMA5 when your controller IO is 5V and you do not need the VIO input; the footprint is identical, simplifying dual sourcing. Choose the NXP TJA1051T/1J or TJA1057GTJ when corporate policy requires an NXP second source - both are 1 Mbps high-speed CAN transceivers in the same 8-SOIC footprint - but budget engineering time to verify pin-5 function and standby/wake behavior, since neither offers the VIO input. For CAN FD or data-phase rates above 1 Mbps, none of these classical CAN parts is appropriate; specify a CAN FD transceiver instead. All candidates are suitable for automotive temperature ranges, but final qualification should reference each manufacturer's current datasheet.

বিকল্পের সাথে তুলনা

পারামিটার এই পণ্য TLE8250GXUMA5 TJA1051T/1J TJA1057GTJ TLE6250GV33
Package PG-DSO-8-16 (8-SOIC) PG-DSO-8-16 (8-SOIC) - same 8-SOIC (3.90mm) - same footprint 8-SOIC - same footprint PG-DSO-8 - same footprint
Brand Infineon Technologies Infineon Technologies NXP Semiconductors NXP Semiconductors Infineon Technologies
Data Rate 1 MBd 1 MBd 1 Mbps 1 Mbps 1 MBd
Physical Layer Standard ISO 11898-2 ISO 11898-2 ISO 11898-2 ISO 11898-2 ISO 11898-2
Duplex / Drivers-Receivers Half, 1/1 Half, 1/1 Half, 1/1 Half, 1/1 Half, 1/1

মূল পার্থক্যসমূহ

  • Separate VIO logic-level supply input (বনামTJA1051T/1J)
  • 150C maximum operating temperature with VIO feature (বনামTLE6250GV33)
  • Same-footprint no-VIO second source within the family (বনামTLE8250GXUMA5)

ডিজাইন নোট

Place the TLE8250GVIOXUMA5 close to the CAN connector to minimize the stub length of CANH/CANL traces; stubs act as transmission-line discontinuities at 1 Mbps and can cause reflections that the 200 mV receiver hysteresis cannot fully mask. Route CANH and CANL as a tightly coupled differential pair with matched lengths and a characteristic impedance near 120 ohms including the connector. Decouple VCC with 100 nF ceramic plus bulk capacitance, and decouple VIO separately with 100 nF since it only sources logic-level gate charge. Keep the split termination (2 x 60 ohm with common-mode stabilization capacitor) at the network ends, not at each node.

Do not tie VIO to a rail that powers up after VCC or floats during microcontroller reset - undefined logic levels on TXD can drive random dominant states onto the bus and disturb other nodes. Tie VIO directly to the MCU IO supply and ensure it is valid whenever VCC is present. Also remember the transceiver is half-duplex: the CAN controller performs arbitration, so never bit-bang TXD manually. When second-sourcing to the TLE8250GXUMA5 (no VIO) or an NXP SOIC-8 part, re-verify the pin-5 function against that part's pin-description table before qualifying the layout change.

Infineon specifies low electromagnetic emission (EME) for the TLE8250G family, but realized EMC still depends on layout: keep the loop area between VCC, GND, and the bus pins small, and place the common-mode choke (if used in the network design) directly at the connector side of the transceiver bus pins. Symmetry of CANH/CANL routing is the dominant factor in common-mode emission; a few millimeters of asymmetry can degrade emissions at CAN bit-rate harmonics. Use the manufacturer's typical application circuit in the TLE8250G datasheet as the reference topology when drawing the schematic.

কমপ্লায়েন্স তথ্য

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
লিড ফ্রি
Unknown
হ্যালোজেন ফ্রি
Unknown
কনফ্লিক্ট মিনারেলস
Unknown

ECCN EAR99 and HTSUS 8542.39.0001 are listed in distributor data. RoHS/REACH status should be confirmed on the Infineon product page before release.

ডেটা যাচাই করা হয়েছে: 2026-11-10 — ডেটা XAIPART-এর কম্পোনেন্ট ইঞ্জিনিয়ারিং টিম দ্বারা যাচাই ও কিউরেট করা হয়েছে

সম্পর্কিত অনুসন্ধান

TLE8250GVIOXUMA5 datasheet TLE8250GVIOXUMA5 pinout TLE8250GVIOXUMA5 equivalent TLE8250GVIOXUMA5 replacement TLE8250GVIOXUMA5 cross reference TLE8250GVIOXUMA5 vs TJA1057GTJ Infineon TLE8250G CAN transceiver TLE8250G application circuit high-speed CAN transceiver SOIC-8 1MBd CAN transceiver with 3.3V VIO TLE8250GVIOXUMA5 price buy TLE8250GVIOXUMA5

সম্পর্কিত কম্পোনেন্ট ও শর্তাবলী

Infineon Technologies TLE8250GVIOXUMA5 TLE8250G TLE8250GXUMA5 TLE6250GV33 TJA1051T/1J TJA1057GTJ NXP Semiconductors CAN transceiver high-speed CAN ISO 11898-2 CANbus physical layer CANopen DeviceNet PG-DSO-8 SOIC-8 surface mount VIO I/O voltage receiver hysteresis half duplex ESD protection automotive ECU industrial fieldbus RoHS 1 MBd data rate
তাৎক্ষণিক বিলওয়াছে রেকোজিউইট
সম্পূর্ণ বিবরণ পূরণ করুন — আমাদের সেলস টিম 24 ঘণ্টার মধ্যে উত্তর দেবে
পার্ট নম্বর উৎপাদক প্যাকেজ QTY লক্ষ্যমূল্য প্রসারিত
✓
বিল প্রস্তুত করা হয়েছে!

আমরা ২৪ ঘণ্টার মধ্যে আপনার ইমেইলে প্রত্যুত্তর দেব

1
RFQ জমা হয়েছে
2
কোটেশন পাওয়া গেছে
3
অর্ডার দেওয়া হয়েছে
4
পেমেন্ট
5
শিপ করা হয়েছে
6
ডেলিভারি হয়েছে
RFQ বিবরণ দেখুন